Search Documents

By W. A. Haley

The use of diesel engines in underground hard-rock mines dates back to the late 1940s. For the first several years, they were used only occasionally, being limited to a few metal mines that experimented with crawler¬mounted front-end loaders, tractor-trailer hauling units, a few tractors for drill-compressor mounts, and utility cleanup machines. By the mid-1950s, track loaders had become commonplace in limestone mines and uranium mines on the Colorado Plateau in the United States, as well as in Canada. Use of crawler-mounted tractors as drill and compressor mounts also increased. By the end of the 1950s, rubber-tired loaders and some haulers began to replace the track-type machines and rail-mounted cars that had been in use. About 1960, the rubber-tired machines brought about a new era of underground mining mobility and flexibility, centered on a method commonly known as "trackless mining." Ultimately, many of the underground rail-type systems for loading and hauling were replaced by the trackless mining technique. ECONOMIC CONSIDERATIONS The size and nature of mineral deposits, plus ground control techniques, historically had dictated small open¬ings to the surface from many underground mines. The small mine openings led to the development of special rubber-tired loaders and haulers designed specifically for access through the small openings. However, some mines, particularly those in massive mineral deposits, are able to excavate and maintain very large openings, and some use modified room-and-pillar systems. With the large mine openings, the use of larger, more produc¬tive equipment such as that commonly found in surface mining becomes economical. In fact, productivity gen¬erally increases at a more pronounced rate than machine size increases because many of the larger machines were designed for heavy-duty shot-rock applications in surface mines and construction sites where the handling of blasted rock is common. Table 1 can be used as a very Table 1. General Productivity Comparison for Conventional Machines In Underground Use (Shot-Rock Conditions) 2.3 m3 (3 cu yd) 4.6 m3 (6 cu yd) Loader Loader Expected Surface 230 t/h 540 t/h Production (250 stph) (600 stph) Expected Underground 90 t/h 270 t/h Production (100 stph) (300 stph) Expected Total Efficiency: Surface 40%-60% 50%75% Underground 25%.-40% 30%50% Expected Useful Machine 8000 hr 12,000 hr Life Before Replacement general comparison of the production and efficiency between small and large machines. Combining greater productivity often inherent in larger machines, with reduced downtime resulting from using fully developed machines with fast parts and service backup, some mine operators have been able to reduce material handling costs appreciably while reduc¬ing manpower requirements for operators and main¬tenance men. Large mine openings increase the amount of rock that must be handled in the development work, and they sometimes increase the dilution in stopes or rooms, de¬pending upon the dimensions of the ore zone. Providing adequate space for the unrestricted operation of large surface mining machines could, therefore, lead to more waste segregation and handling costs. It could also cause greater ore dilution that would result in a lower grade of ore being delivered to the processing plant. The tradeoffs between opposing cost factors must be reconciled and balanced to achieve the best overall cost of the crude ore, concentrates, or product. EQUIPMENT MODIFICATIONS Loaders and haulers designed for surface mining are seldom used underground in their standard con¬figurations without some modifications. If done, the modifications generally are made by the equipment dealer and/or the user, and the modifications usually include one or more of the following items: 1) The exhaust stack is lowered, and its direction is changed. Usually, it is repositioned horizontally to the rear, or it is fed into the engine fan to diffuse the exhaust gases. 2) The operator's position is lowered by either lowering the seat or changing the seat to a side mount. 3) The operator controls are adjusted to fit the new operator position. 4) Other components, such as the radiator and loader tower, are lowered. 5) Special bumper guards are mounted at the base of the radiator area. 6) An exhaust conditioner is mounted and con¬nected, using either a catalytic or a water-type condi¬tioner, or both. This usually is controlled by the safety and health regulatory authority having jurisdiction. 7) The positions of other components are rearranged

Jan 1, 1982

By Thomas J. DeMull

Amax Gold's Sleeper Mine was brought to production as an open pit mining, cyanidation milling operation in March 1986. The Sleeper deposit is unique in that it contains zones of very high grade gold ore. Despite blending of ore, mill head grades have varied over a broad range. These grade variations were anticipated during mill design and affected, in particular, the sizing and selection of equipment for the CIP circuit. When grades proved to be even higher than anticipated, design operating parameters were adjusted shortly after start-up to accommodate the higher grades. Operating results have been excellent: during the first 18 months of operations the Sleeper mill has processed 375,600 tons of ore and produced 229,000 ounces of gold.

Jan 1, 1998

By J. Drelick

Among the wide variety of modern surface chemistry analytical techniques, contact angle measurements still remain attractive for wetting characterization of solid surfaces. The captive-bubble and sessile-drop techniques are the most popular methods for the examination of flotation systems. Systematic measurements of advancing and receding contact angles for several three-phase systems using the captive-bubble and sessile-drop techniques show that the contact angle measurements depend on the technique used and may differ significantly for some heterogeneous and rough solid surfaces. Importantly, it was found that these discrepancies in contact angle measurements depend on the bubble (drop) size. Contact angles as measured with the static captive-bubble technique are compared with those measured with the dynamic captive-bubble technique, in which the capture of a bubble at the solid surface results after buoyant transport and attachment The dynamic captive-bubble technique allows for the formation of much smaller bubbles than is possible with the static placement technique in which a bubble is placed at the solid surface with a microsyringe. Although this dynamic technique cannot be recommended for the systematic wetting characterization of solid surfaces, its significant advantage is the ability to examine the contact angle/bubble size relationship over a wide range of bubble sizes, from several micrometers to several millimeters in diameter.

Jan 1, 1995

By W. H. Dickinson

The performance of seven antiscalants spanning a range of chemistries was evaluated for control of calcium carbonate (CaCO3) formation in gold processing applications. Three preferred chemistries were identified which provided up to 100 percent inhibition in static jar tests when applied at 30 ppm dosage. The three products were further evaluated using a model carbon extraction circuit developed for this application. The test circuit enabled direct measurement of calcium carbonate formed on the carbon from a supersaturated solution under dynamic conditions. The antiscalants lowered CaCO3 buildup on the columns by 15 - 26 percent compared to untreated controls. Impact of the antiscalants on the rate and extent of gold loading onto a carbon adsorbent was evaluated in laboratory carbon-in-pulp (CIP) studies. The antiscalants generated a 25 - 35% increase in gold loading at gold extraction efficiencies up to 65%. On-site testing at a gold processing facility demonstrated that 10 ppm of the preferred antiscalant was able to fully suppressCaCO3formation in thickener overflow water.

Feb 27, 2013

By Mark E. Gershon

The development of long term plans and schedules for strip mines now faces many companies, especially those developing large properties in the West. The rule of mining the lowest strip ratios first, while delaying equipment acquisitions and recouping investment the fastest, creates the situation where stripping ratios are too high in the latter years of mining operations. A program concept taking life of mine return on investment into account is developed in this paper to optimize mine scheduling and equipment acquisition. In addition, quality considerations (heat content, ash, sulfur, washability) can be considered by including the appropriate blending constraints to meet contract requirements.

Jan 1, 1983

By C. H. Smith

The present interest in beryllium seems to be the result of recent developments in the uses for the metal discovery of significant deposits of disseminated beryllium ores, and the development of chemical and physical processing techniques, for recovering the beryllium values contained in these ores. At the present time most of the new and potential uses for beryllium are in the research stage of development and are not consuming large quantities of the metal. However, they do point to an expanding market. Interesting new discoveries or extensions of previously known deposits have been reported during the past year from the Boomer Mine in Colorado, the Mesquite area of Nevada,, the Chemalloy pegmatites in Canada, the Brazilian and African pegmatite districts and from other areas, However, this paper will discuss only four of the beryllium deposits, which appear to be of special significance due to their; large reserves of ore and promise economic development. The new chemical and physical processing techniques are not discussed in detail, but it should be stressed that the development of an economical process to handle the pegmatitic and low-grade non-pegmatitic beryllium ores is of great importance to the development of the beryllium industry. Scientists in both government and industry are co-operating in this effort and it is expected that commercial processes will be developed in the near future.

Jan 1, 1962

By Charles Stone, Hannes Lagger, Dru Desai

The design methodology of the planned Second Avenue Subway Project (SAS) led to development of the initial support design to estimate cost and quantities in the Preliminary Engineering (PE) stage. Careful selection of the cavern design rules that recognized the impact of rock quality, rock cover, excavation geometry, and excavation sequence helped to overcome the design challenges of large, shallow caverns for the initial ground support. In the course of the design verification process prescribed by the design methodology, the design team was continuously reviewing and updating the support quantities. The design procedure includes methods using different approaches of empirical, continuum, and discontinuum analyses, which are currently advanced in the Final Engineering (FE) stage. The paper is a continuation of the RETC 2005 “Trials and Tribulations” and focuses on the procedures that led to the changes in the initial support as a result of the ongoing design development.

Jan 1, 2007

By A. T. Iannacchione

From 1990 to 1996, 16 states reported 92 injuries from falls of roof, rib or face in the more than 90 underground stone mines in the United States (Fig.1). Missouri, Pennsylvania and Kentucky accounted for 48% of the total number of injuries (Fig. 2). Of this total, 11 miners were killed. Of the 11 fatalities, 10, or 91%, were associated with unrecognized loose or failed rock within the roof beam. Additionally, unrecognized roof beam failures resulted in a majority of the falls of ground injuries occurring in underground US stone mines from1990 to 1996. This number is not large in magnitude. But a workforce of fewer than 2,000 miners makes for a high fatal-accident rate. The severity of the typical fall-of-ground injury is, in general, very high. About three-fifths of all roof, face and rib fall injuries were designated by the US Mine Safety and Health Administration (MSHA) as some kind of lost time accident. MSHA assigns each accident a severity value from one to six. A one represents a fatality, a two, a permanent disability and three, a lost time accident (Fig. 3).

Jan 1, 2000

By J. Potter, A. Anani, C. Antonio

This research aims to test the hypothesis that the low retention rate of women in the mining industry is caused by workplace culture and policies established due to gender segregation. A quasi-experiment is developed to determine the cause-and-effect relationship between gender segregation-inspired culture and the retention of women. The experiment considers the impact of the job type and the operational environment. The analysis provides information on factors that cause low retention of women in the industry, the extent to which gender segregation plays a role, and insights that allow actionable and measurable changes in the industry.

Feb 1, 2023

By A. A. Schweizer

Buckhorn ore is hydrous, argillized basaltic andesite, and is at least 60% clay composed of kaolinite and subordinate montmorillonite. Moisture content runs from 10% to 25%. The original crushing plant was a typical compression type, employing a jaw crusher, and two cone crushers. The system was plagued with constant plugging and unable to meet production plans. The three compression crushers were replaced with a Stamler Feeder Breaker followed by a Hazemag Impactor. Production plans are now exceeded. Agglomeration has progressed from an agglomeration drum to cascading conveyors, to introduction of the lime and cement into the primary crusher.

Jan 1, 1987

By J. R. Allen

Environmental laws and regulations have proliferated over the last two decades. 1/ Within the last year, Congress has dramatically expanded the scope of the Superfund program 2/ and has enacted significant new amendments to the Clean Water Act.3/ In addition, EPA has shown no signs of slackening the pace at which it promulgates new regulations to implement statutory programs. The agency projects that over the next few years it will issue approximately 275 new regulations under the statutes it implements. 4/

Jan 1, 1988

By W. V. Liu, D. Omane, H. Yu, Y. Pourrahimian

"A large-scale wildfire had broken out at Fort McMurray in Alberta, Canada during May 2016. Many oil sands mining activities were affected due to the wildfire and the associated ash emissions. In particular, ash emission generated from the fire outbreak is a huge problem during the post-fire cleanup. These emissions pose a severe health hazard to workers, environment, and global climate. The ashes emitted into the atmosphere are caused by either human activities or climate conditions. The objective of this research is to assess the effect of three different ash dust suppressants, namely water, #1 surfactants, and #2 polymers at various volumetric concentrations on ashes samples to prevent propagation of fine solid emissions into the atmosphere. It is found that both #1 surfactants solution and #2 polymers solution are effective in retaining fugitive ash dust generated from the ashes. Volumetric concentration efficiency of 0.05% of #1 surfactant and 5% of #2 polymers in 500 ml of water have been proven to provide ash dust retention efficiency greater than 99% after the spraying of these suppressants. It is also found that both #1 surfactants solution and #2 polymers solution maintain an ash dust retention efficiency higher than that of the use of only water. This confirms the merit of using chemical dust suppressants on fugitive ash dust for a longer period, which is proven by the 72-hour data from this experiment. This study gives a general view of how effective chemical suppressants on fugitive ash emissions work. INTRODUCTION On May 1st, 2016, a large-scale wildfire gutted Fort McMurray, Alberta, Canada. Many oil sands mining activities were affected due to the wildfire and the associated ash emission. Due to the wildfire, some of the biggest oil sands companies in Fort McMurray such as Royal Dutch Shell and Suncor Energy shut down their oil production, at 255,000 and 350,000 barrels per day respectively [1]. Syncrude Canada Ltd scaled down its normal production capacity level of 350,000 barrels per day [1]. This generated an estimated loss of about 1.1 million barrels of oil production per day, constituting a 30% reduction in the Canadian daily oil production, crippling the economy [2]. This loss in production by the companies translated into 0.33 % of the Alberta GDP in 2016 constituting a loss of $985 million and 0.06 % of the entire Canadian economy [3]. In 2017, it is estimated that the rebuilding and reclamation of the affected areas in Fort McMurray will add $ 1.3 billion in GDP to Alberta’s economy [3]. A population of over 90,000 people was evacuated from the location and its surroundings for health and safety reasons [4]. The fire destroyed about 2,400 structures and over 500,000 hectares of forest vegetation in Fort McMurray, leaving an estimated 232,000 tonne of post-fire ashes [5,6]."

Jan 1, 2017

By Simon Strong, Tim Brown, Luis Ignacio Sanz Vivanco

"One of the most significant technical and practical challenges facing the tunnel construction team on the Legacy Way road tunnel project in Brisbane, Australia was how to erect the pre-stressed precast concrete slabs to form the smoke duct in the tunnel boring machine (TBM) tunnels. An essential part of the tunnel ventilation system, the smoke duct, extends the full length of the 4.6km long twin, two lane tunnels. The vast majority of the tunnels (approx. 4.3km) were constructed using two 12.4m diameter double shield TBMs. The refurbished Herrenknecht machines broke several world records on the way to completing the tunnel excavation works in just over nine months. With the excavation complete the focus turned to solving the complex civil tunnel fit out challenges. A key component of the civil fit out of the tunnels was constructing the smoke duct in the TBM tunnels which was designed as a precast solution. The slabs which each measure 8.62m long by 2.0m wide by 200mm thick and weigh close to 9 tonne need to be erected above cast in situ corbels whilst other tunnel finishing works continue. The space proofing clearance offered by the design to the support corbels below and the precast segmental lining above was in the order of only 100mm. This paper details the events of how the Transcity JV tunnel fit out team, comprising some of Europe and Australia’s leading tunnel construction specialists, drew upon the global strengths of the existing JV member companies and the global reach of leading TBM manufacturer Herrenknecht to develop an innovative system to solve this challenging problem. This globetrotting story, which starts in Australia, visits Europe and mainland China before returning to Brisbane where it all began."

Jan 1, 2016

By R. M. Wilson

Concentrating plants, in common with other types of industrial plants, cannot operate without lectric power. The elctric distribution system and utilization equipment; therefore, must be carefully considered in all phases of plant design. Two important aspects of proper distribution and usage of electric power are the selection of voltage levels and the methods of system grounding. These are not necessarily the most important design considerations, but are perhaps more controversial than other major points, Modern plants demand increasing amounts of power which, since electric power is the product of voltage and current means higher voltages or currents. Higher voltages require more insulation, higher currents more conductor. The equipment designer?s problem is to obtain in his transformer, cable, switchgear, controller, motor, etc a balance of insulation and conductor to obtain a satisfactory design at lowest cost. To provide the most economical system, both in initial and operating costs requires the system designer to select the proper voltage level. Adequate voltage also permits expansion to meet future requirements, and results in better operation of utilization equipment, Relatively little advancement has been made in recent years in improving conductors; however, great progress has been made in improving insulation. Thus modern plants, in general, now find it more economical to use higher voltages than they did previously. For example plants which only a few years ago would have used 2400 volts as a system voltage often find nowdays that 4160 volts is their proper choice. If the plant requires 10,000 kva br more, then an even higher voltage, such as 13,800 volts, will prove economical. However, for the average concentration plant, with less than 10,000 kva demand, the choice of distribution voltages is between 2400 and 4160 volts, and 480 volts will be used for the low voltage utilization system.

Jan 1, 1958

By John A. Wolfe

Applications of mathematical statistics to the field of exploration are still relatively new. There are two primary reasons why little has been published in this field. First, if one discovers an effective technique for exploration, he does not like to disclose it. Second, the geologist needs to work closely with a mathematical statistician, and the communications barrier between the disciplines is formidable. The authors of this paper, one a geologist and the other a statistician, were interested in the economic benefit which appeared to be possible in the interdisciplinary area which they have called "geostatistics." An actual example has been selected to illustrate this benefit.

Jan 1, 1962

By P. Samanta, Mohammed N. Azad, Gustad F. Taraporewalla, A. K. Mukherjee, Abhay S. Patra, D. Sachinraj

Beneficiation of coal is a water intensive process, and the water is recovered in downstream operations in the high rate thickener (HRT) and vacuum belt filtration (VBF). Clean coal particles entering the HRT have an inherent tendency to enter the overflow because they are extremely fine and hydrophobic. Hence, flocculants (polymers) are used to floc the ultrafine particles so that they settle and enter the underflow. Ultrafine coal particles (−37 μ), which are highly hydrophobic, if present in the stream, will not be efficiently captured by using flocculants alone. This is observed in the normal plant operation at one of the beneficiation plants in the Jharia region, Jharkhand, India. Approximately 6–7% of the feed to the HRT enters the over flow (supernatant water). Hence, this amount of clean coal particles is not recovered and account for production losses. A comprehensive settling and dewatering test work was conducted with clean coal slurry using several commercially available reagents. Studies were also done on different combinations of reagents, including coagulants and surfactants along with flocculants, to improve the settling behavior of the coal particles. The reagents were assessed based on their performance with respect to settling rates, overflow water clarity, and compaction of the underflow solids. Emphasis was given to the ability of the reagents in compacting thickener underflow to higher densities so that maximum water could be recovered from the thickener. Pretreatment of highly hydrophobic coal slurry with a combination of coagulant and surfactant followed by flocculation showed very good settling characteristics with clear overflow.

Sep 30, 2021

By James B. Meredith

The European Economic Community (The Common Market) is now shifting from I a coal oriented to an oil oriented economy. The proportion of energy supplied by oil has increased from only 13% in 1950 to 38% in 1962, and will approach 50% by 1970. In the past five years Common Market petroleum demand has in- creased 15% per year compared with only 3% per year in the United States. This rapid shift to oil can be explained by looking at oil's competition, First; there is simply not enough other energy - European coal, natural gas and hydro-electric power - to meet the demand, Secondly, oil?s primary competing energy in the Common Market is coal, and Community coal is high-priced - it costs more than two and a half times as much as U. S, coal at the pithead. The third reason for the shift to oil is consumer preference for the ease of handling, convenience and cleanliness of liquid fuels. As these reasons suggest, much of the shift to oil and the resulting growth in demand would have occurred whether or not the Common Market organization had existed. On the other hand, the Common Market has stimulated the use of oil by causing a higher rate of energy consumption, and oil has been the beneficiary of most of this growth.

Jan 1, 1963

By Alexander N. Winchell

"The deposits of the east end of the Mesabi Range cover very large areas, and consist of the same taconite that produces the hematite of the central and western Mesabi. It is not deeply covered with drift, but outcrops boldly in large masses. It is not concentrated locally into enriched bodies separated by leaner areas, but is all a fairly uniform, hard, banded, unaltered chert, carrying about 25 to 30 per cent iron as magnetite.The Mesabi Iron Company, organized by Hayden, Stone & Co., and under the direction of D. C. Jackling, has taken over these deposits and is building a Concentrating plant at the new town of Babbitt, about fourteen miles east of Mesaba, Minn. This plant is to have a capacity of 2,000 to 3,000 tons per day, and is based on the application to this low grade material of the methods which have made the so-called porphyry copper properties so successful.In 1916, an experimental mill was built in Duluth; containing full sized machinery and capable of handling from 100 to 200 tons daily. A considerable tonnage of material was concentrated here during 1916, 1917 and 1918. The work showed that the resulting product could be varied, almost at will, between 60 per cent and 70 per cent iron and .006 per cent to .030 per' cent phosphorus, and that this could be made on a large scale well within the limits of cost set by iron trade conditions. A small special cargo was sent down the lakes, late in 1918, assaying 63.27 per cent iron (natural and dry) and .008 per cent phosphorus; but it is assumed that large scale shipments will normally be of a Bessemer' grade carrying about 63 per cent iron and .020 per cent to .030 per cent phosphorus. This material is a sinter, carrying only traces of sulphur and titanium, with silica between 6 per cent and 10 , per cent, and alumina, lime, magnesia, and manganese, each below 1 per cent. Some of the iron in this sinter is hematite and some is magnetite, the percentages varying according to the treatment given on the sintering machine. Like the analyses, this hematite percentage is within reasonable control. Sinter made from finely ground magnetite has much the structure of coke, being firm yet porous, and gives good account of itself in the blast furnace."

Jan 1, 1920

By Quanjun Liu, Rongping Lin, Rongdong Deng

Arsenic contamination significantly affects the quality of copper concentrates, presenting challenges during smelting processes. Considering that covellite and enargite have similar surface properties, they are difficult to separate by flotation, resulting in copper concentrates with excessive levels of arsenic. To address this issue, this study systematically investigated the flotation separation of covellite and enargite in microflotation and bench-scale flotation tests using calcium lignosulfonate as a depressant, with the results indicating that calcium lignosulfonate can be used to separate covellite and enargite because it enables the separation of arsenic-bearing copper minerals into high- and low-arsenic (As 0.57%) copper concentrates. According to contact angle and adsorption tests, scanning electron microscopy–energy dispersive spectroscopy, and X-ray photoelectron spectroscopy, the differential adsorption of calcium lignosulfonate onto covellite and enargite is the primary reason for their distinct flotation behaviors in the presence of calcium lignosulfonate. The selective depressive effect of calcium lignosulfonate provides a novel approach for improving the flotation separation of arsenic-bearing minerals from copper sulfide minerals.

Feb 28, 2024

By Kevin J. Ashley

Coal is deposited at a mine site in several thin seams which outcrop in rolling hills and dip at about 8° to the northeast. The deposit is located in the northeast area of the State of New Mexico in the Southwest of the United States. A drilling program was undertaken and was quite irregular. Not all of the seams appear in all of the drill holes. Some of the holes did not go deep enough, while others were drilled below the outcrop of some seams. Occasionally a seam would pinch out and not be seen in a drill hole. Also, the outcrops of the seams are buried in many places by several feet of alluvium. All of these factors make correlation of the seams between drill holes difficult. The drawing of cross sections in three directions and at many locations across the mining area have been necessary to assure the accuracy of the input data.

Jan 1, 1982