Search Documents

By Nick Rose, Mathieu Veillette, Matthew King

"The Teck Highland Valley copper (THVC) mine is located approximately 55 km (34 miles) southwest of Kamloops and approximately 20 km (12 miles) west of Logan Lake, BC, Canada (Fig. 1). Mining at THVC is conducted at three openpit operations comprised of Valley, Lornex and Highmont with a total annual output on the order of 300 kt (330,000 st) copper concentrate and 5 kt (5,500 st) of molybdenum concentrate. The Phase 8 pushback in the Valley Pit (Fig. 2) was mined from 2011 to 2016. Successful slope steepening occurred in the later stage of the pushback with the implementation of presplit blasting in 2015 and 2016.This article summarizes the investigation and design approach including: structural analysis, kinematic assessments of bench breakback potential, development of discrete fracture networks (DFNs) to characterize discontinuity fabric, rockfall modelling, 2D anisotropic limit equilibrium and 2D distinct element modelling, assessment of potential kinematic failure modes affecting double benches with 3D distinct element modelling and improved blasting techniques using e-dets. THVC is currently undertaking a mine life expansion involving the pushback of the west wall of the Valley Pit above Phase 8 to extend the mine life to 2029. Engineering geologyThe east wall slope in the Valley Pit is comprised of a 350-m (1,148-ft) thick sequence of glacial valley sediments that occur along the Highland Valley (Fig. 2), exposing an overburden slope up to about 225-m (740-ft) high below the crest of the ultimate east wall. The glacial overburden units consist of pro-glacial outwash and glaciofluvial deposits, glacial outwash sands and gravels interbedded with till and alluvial fans consisting of cross-bedded sands and sandy-gravels. Lacustrine sediments occur within the mid to lower portion of the glacial sequence and contain intervals of low-shear-strength clays and silts. Two large (1.3 and 7 Mt or 1.4 and 7.7 million st) waste rock buttresses were required to maintain slope stability using slot-cut and fill mining methods, as described in Fortin et al. (2011).The Valley porphyry deposit occurs in the central portion of the late Upper Triassic Guichon Creek Batholith, which intrudes assemblages of the Permian Cache Creek and Upper Triassic Nicola groups. The Valley deposit occurs in an area of intense fracturing near the intersection of the northerly trending Lornex Fault and the northwest to westerly trending Highland Valley Fault."

Apr 1, 2019

By B. Briggs

Over the past 15 years, the tunneling industry has pushed towards a higher degree of mechanization in nearly every phase of construction. The overall objective of the mechanization was to increase production and the level of safety in tunnel operations. However, the overall complexity of some systems have been a hindrance to a seamless transition to the newer technologies as increased maintenance requirements and re-training of skilled workers has altered the benefit curve for some innovations.

Jan 1, 2010

By Jacob L. Brinkman, Catherine E. Johnson

Unmanned aerial vehicles (UAVs) are being explored by researchers to measure concentrations of gas emissions in situations where such measurements are otherwise extremely difficult to obtain, such as NO and NO2 (NOx) emissions from surface mine blasting. Recently, countries have imposed or are planning to impose surface blasting gas pollution regulations, which creates a need for an improved understanding of UAV-based gas measuring systems. The experiments detailed in this paper were performed to determine if airflow generated by the rotors, also known as downwash, unnaturally alters concentration measurements. Downwash turbulence could create locations of varying pressure, which could affect concentration. A UAV fitted with gas sensors was attached to a stand in a controlled environment containing a mixture of NOx. The gas sensor measuring points were placed at various distances on and from the UAV body to evaluate downwash effects on gas concentration. Results show that the presence of downwash turbulence causes no statistically significant changes to concentration measurements at any distance or direction from the UAV. Based on these results, it is possible to use a UAV-mounted gas monitor to measure concentrations without concern for downwash interference, provided the UAV and measuring point are entirely contained within the gas cloud.

May 20, 2021

By O. D. Staman

The risk assessment project examines the likelihood of inorganic contaminants from copper dump-leaching operations to contaminate domestic water supplies. The project examines contaminant transport by modeling contaminant movement from the base of a leach pile through the unsaturated zone and into the saturated zone. The modeling effort is unique in that it models infiltration, contaminant transport in the unsaturated and saturated zone combined with geochemical modeling of the unsaturated zone. The project incorporates probability theory to reflect the uncertainty of hydrogeologic parameters.

Jan 1, 1994

By F. B. Henderson III

Since the "end" of the Cold War, revolutionary new research and commercial remote sensing capabilities are being developed that will dramatically change the way we map the earth and address its environmental problems. The technology challenge is not the growth of new environmental remote sensing technologies themselves. It is, rather, how these new innovative observing systems can be accepted and used to the benefit of both the regulatory and the mining communities in the light of present concerns about unknown risks of discovery and liability. The basis for this paper is an unpublished technology primer prepared for the industry-government Workshop on Advanced Measurement and Site Characterization for Mining Impacts held at Colorado School of Mines, Golden, Colorado, July 14-17, 1997

Jan 1, 1999

By Pierre Longtin

"Replacing the aging roadway access to the iconic Golden Gate Bridge, thereby ensuring traffic safety and robustness in case of seismic occurrences, provided an opportunity for major design improvements as well as the development of a parkway that would include the construction of four new tunnels. With an eye to the future, the Doyle Drive replacement project aimed to meet the highest standards for environmental stewardship beyond regulatory requirements. Understanding that lighting equipment is the tunnel‘s subsystem that uses the most energy, the operator was looking for a sustainable solution to light the tunnels. An Intelligent Lighting Control System (ILCS), designed specifically for road tunnels, was acquired to individually control the almost 2000 luminaires lighting the four tunnels. This paper will show the results in terms of energy and operational savings generated over the nine months of operation between the commissioning and the conference in April 2016. INTRODUCTION Electrical & mechanical (E&M) equipment represents an average of 10 % of a tunnel total construction cost. Once the civil infrastructure completed, E&M equipment drives the main part of the expense during a tunnel useful life. Table 1 below describes the impact of various types of energy consumption and their cost impact in tunnels of less than 500 m. It is clear that lighting is the sub-system that requires the most energy. A good lighting strategy is the key to reducing energy consumption due to lighting and a viable solution that will bring important savings in tunnel operations.With a price of $0.14/kWh in California and a planned increase between 3% and 6% per year during the period 2013-2040, the tunnel operators could not afford to overlit the tunnels—particularly when they have to operate it for the next 30 years. However, they also need to maintain the right lighting level to ensure driver safety all the time. The Presidio Parkway project includes the Battery tunnels, which are 240 m (790 feet) and 230 m (750 feet) in length, and the Main Post tunnels, which are 280 m (920 feet) and 315 m (1030 feet) in length."

Jan 1, 2016

By Robert R. Dorfler

We ought not look back unless it is to de- rive from past errors, and for the purpose of profiting by dear bought experience. - George Washington During the mid 1960's, the application of automation was introduced to Climax by two process control companies. In 1969 Climax decided to seriously consider improved control of selected areas of their milling process after preliminary research had been completed on two rougher ball mill grinding circuits. In 1971 the Climax Mill Department developed a direct digital control scheme for rougher milling, designed a remote control center for handling process water, planned to automate the central steam heating facility for energy conservation, and convert other plant areas to automation. All twenty rougher grinding mills and the industrial water system were automated by 1977. The idea of automating central heating and other areas was abandoned although some fuel conservation items were installed at the heating plant. During this period from 1971 to 1978, the mill capacity was expanded from 39,000 metric tons per day to 43,000 metric tons per day and cyclone classification was introduced to rougher milling. Ore quality changes degraded the milling recovery from over 90% to less than 85%. This report describes the procedure the mill used in developing the automatic process and the occurances that affected the timing and fina1 control logic. The report deals primarily with the automation of the ball mill grinding, classification and flotation process as this was the bulk of the seven-year project.

Jan 1, 1979

By Joseph M. Zigich

The Anaconda Minerals Company operates a molybdenite and copper producing mine and mill facility near Tonopah, Nevada. Included with the milling facility is a ferric chloride leach plant for removal of copper mineralization from the molybdenite concentrates. Discussed are the engineering and construction schedules associated with the leach plant. The chemistry associated with the process along with a description of the process flow, equipment, and operating parameters are contained in the paper.

Jan 1, 1983

By Jake Gibson

"As one of the most pressing and important political debates of this century, climate change has captured global attention and is forcing governments to take action toward decreasing greenhouse gas (GHG) and carbon emission levels below what was previously thought to be necessary. With the ever-increasing price of diesel fuel, accompanied by the popular topic of carbon taxes and greenhouse gas emissions, the mining industry is looking to industry specialists for assistance. The benefits of a no-idle policy reach far beyond carbon reduction and fuel savings, ranging from decreased maintenance to increased engine life. With products like battery-powered ac systems and diesel-fired heaters, going noidle is easier today than ever before. With both systems being manufactured to withstand the harsh environments of the mining industry, the end user will see a seamless change from conventional, inefficient belt-driven systems to future, standalone mobile equipment HVAC.The history of GHGs and climate changeIn 1896, Svante Arrhenius first claimed that the combustion of fossil fuels may eventually result in enhanced global warming, but not until 1955 did Gilbert Plass draw global attention to global warming by summarizing that adding carbon dioxide to the atmosphere would intercept infrared radiation and thus warm the earth. Then in the early 1960s, Charles Keeling developed modern technology to produce concentration curves for atmospheric CO2 (Fig.1).In 1988, the Intergovernmental Panel on Climate Change (IPCC) was founded by the United Nations after acknowledgment of a rising global annual temperature. The IPCC consists of more than 2,500 scientific and technical experts from more than 60 countries. Because climate change could not be solved by a single country, the Kyoto Protocol was negotiated in 1998, requiring all participating countries to reduce their GHG emissions by at least 5 percent from the 1990 levels. The Protocol was signed by 186 countries in 2001 (since then several countries have retreated from the agreement, including the United States). In 2002, the Bush administration announced a policy for climate change relying on domestic, voluntary actions to reduce the "greenhouse gas intensity" of the United States economy by 18 percent by 2012. The U.S. still attends the Kyoto conference of parties (COPs) but does not participate in negotiations, as it is not bound by its terms."

Jan 1, 2014

By A. H. Summers

The La Choya mine is located 55 km south of Sonoyta in northwestern Sonora, Mexico. Mineralization is controlled by a 40 meter thick thrust fault zone which created a permeable host for the metal-bearing hydrothermal solutions. The ore body is mined by open pit using wheel loaders and truck haulage. Gold and silver are recovered from low grade ore by heap leaching followed by carbon adsorption.

Jan 1, 1997

By Mahiyar Nasarwanji, Jonathan K. Hrica, Jonisha P. Pollard, Lydia M. Kocher, Brianna M. Eiter

Within the metal/nonmetal mining sector, fall-related incidents account for a large proportion of fatal and non-fatal injuries. However, the events and contributing factors leading up to these incidents have not been fully investigated. To help provide a clearer picture of these factors, an analysis of imminent danger orders issued by the Mine Safety and Health Administration (MSHA) between 2010 and 2017 at both surface and underground metal/nonmetal mine sites revealed that most orders are associated with fall risks. Of these cases, 84% involved the workers not using fall protection, fall protection not being provided, or the improper use of fall protection. Fall risks for workers most frequently occurred when standing on mobile equipment, performing maintenance and repairs on plant equipment, or working near highwalls. In most cases, a single, basic, corrective action (e.g., using fall protection) would have allowed workers to perform the task safely. Overall, these findings suggest that a systematic approach is needed to identify, eliminate, and prevent imminent danger situations. Furthermore, to protect mineworkers from falls from height, frequently performed tasks requiring fall protection should be redesigned to eliminate the reliance on personal fall protection.

By Allan G. Provost

Shaft construction is assuming ever increasing importance when new mining enterprises are considered. The reasons for this increased emphasis is the much greater depths at which many new ore-bodies are being developed and the rapid depletion of near surface reserves requiring mines to go to greater depths on existing deposits. These greater depths increase the probability of exposure to unfavorable geologic conditions and it is more likely that high ground and/or water pressures will be experienced at these depths. The large capital costs involved and the critical position of a shaft in the overall mining program necessitate that this element of project development be given careful and critical consideration. The Henderson No. 2 Shaft is located in the Rocky Mountains of north central Colorado (See Figure I), about 55 miles west of Denver, near the community of Empire in Clear Creek County. At the 10, 442 foot collar elevation, winter arrives in late September and brings snow to contend with until May. The labor force for Shaft No. 2 is approximately 90 men. They are provided access to the project via all-weather U. S. Highway 40. SHAFT DESIGN The Henderson No. 2 Shaft is a 28-foot I. D. circular, concrete lined (1 foot thick) vertical shaft. The final depth will be approximately 3100 feet

Jan 1, 1972

By M. Portal, L. Goicochea

This study is carried out in the Zenit mining concession, which is located in the city of San Pablo in the department of Cajamarca in Peru. The Project has 33 mineralized structures and according to laboratory analyzes we have the presence of gold and silver. The geostatistical evaluation provides an analysis on the distribution of precious metals in the vein. This information is used to improve the efficiency of metal extraction and to reduce costs. The general objective is to evaluate the polymetallic veins (Au and Ag), for which the classification of resources (measured, indicated, and inferred) has been carried out, taking into account the parameters of minimum distance from the composite, corresponding volume and tonnage calculation. In addition, an inventory of estimated geological resources was carried out with the block grades obtained to generate the tonnage-grade curves.

Feb 1, 2024

By D. Shuck

Incorporation of a 2,727 mtpd, $5.7 million flotation circuit into the Mclaughlin flowsheet was completed in November 1991. This capital addition reduced overall operating costs and improved the gold recovery of the low grade refractory reserves over that expected for direct cyanidation. In addition, flotation provided a means to generate a sulfide concentrate which is utilized to supplement feed to the pressure oxidation circuit.

Jan 1, 1994

By Ali Ekrem Aritan

Exposure to hand-arm vibration (HAV) among the labor force in the mining industry can result in permanent vibration diseases such as behavioral disorders, visual impairment, osteoporosis, pain (mostly in the hands, wrists, and shoulders), circulatory system disorders, and malnutrition. In this study, the vibration exposure of excavator operators working regularly in 25 different natural stone quarries was measured. In addition, the relationship between vibration exposure and rock properties was investigated. Gloved and ungloved vibration measurements were performed and revealed that antivibration gloves reduce excavator operators’ vibration exposure by 7.10–25.95%. Samples from each quarry were characterized with rock mechanics tests. The correlations between the hand-arm vibration measurements and the natural stone physical–mechanical properties (uniaxial compressive strength, Shore hardness, Knoop hardness, apparent density and total porosity) were determined to be over 70%. One finding of the study was that the health risk in excavators cannot be reduced sufficiently by the sole use of antivibration gloves. Furthermore, the excavation of any rock with a Knoop hardness above 121 is associated with an 81% risk of HAV. To increase awareness of the danger of vibration exposure for natural stone miners, training programs should be provided, and technical and operational changes should be implemented.

By Sandeep Kumar Asarapalli, Sunil Kumar Bisoyi, Bhatu Kumar Pal

Spontaneous heating of coal is one of the major concerns in the coal mining industry. Hundreds of millions of tons of coal are lost each year because of spontaneous heating. If necessary arrangements are made, many fires due to spontaneous heating may be avoided. Therefore, protective measures have become essential to prevent coal from spontaneous combustion. A large amount of coal reserve can be saved by the assessment, suppression, and prediction of spontaneous heating of coal, which also helps in betterment and efficient coal production. The use of chemical retardants can act as inhibitors for the liability of coal toward spontaneous heating by increasing its ignition temperature, thereby, increasing its incubation period. The coal-chemical mixture can be used for whitewashing the exposed coal in galleries as it creates a layer between coal and oxygen in the atmosphere, delaying the oxidation process and ultimately inhibiting the spontaneous heating liability of coal. This work examines the effect of chemicals such as sodium chloride, calcium carbonate, potassium iodide, sodium nitrate, and potassium chloride on the spontaneous heating of a coal sample. Thereby, it suggests a better chemical for inhibiting the liability of coal toward spontaneous heating. The experimentation involves flammability temperature (FT), crossing point temperature (CPT), and differential thermal analysis (DTA). The ignition and oxidation temperatures were found from the above experimental methods for Lingaraj open-cast coal mine samples, with and without adding chemicals. The results are cross-checked and verified through DTA. Correlation analysis was carried out among the results obtained from CPT, DTA, and FT, and better chemical retardants that effectively inhibit coal’s tendency toward spontaneous heating were suggested.

Dec 23, 2023

By Robert L. Wade

The two primary goals in underground coal mining are to improve safety and to lower mining costs per ton through increased productivity. However, as evidenced by the drastic decrease in. productivity since the enactment of the 1969 Coal Mine Health and Safety Act, (the Safety Act), these goals appear to be mutually exclusive. Millions of dollars have been spent in the res, arch and development of systems to solve this problem. Before the Safety Act, "productivity had experienced a 25-year history of continued increases ...? (Douglas, 1980). But since its enactment there have been dramatic decreases in productivity accompanied by phenomenal increases in mine costs. Labor trends, depletion of the more readily minable underground coal reserves and other factors have contributed to this situation, but the dominant factor is undoubtedly the Safety Act itself. To illustrate, prior to 1969 underground coal mine production was much greater than surface mine production but since then underground mine production has been declining at a rate greater than the overall growth rate of total coal production.

Jan 1, 1985

By K. V. Raj, M. McNinch, A. L. Miller, J. Wilson, D. A. Parks

Diesel particulate matter (DPM) has been shown to contribute to various adverse health effects on underground miners. In order to reduce worker exposures, it is critical to measure the levels of DPM in the active work settings and in real time. However, the 5040 method, developed by the National Institute for Occupational Safety and Health (NIOSH), which quantifies the mass of elemental carbon (EC) and organic carbon (OC) in the samples, is based on full-shift samples, and can take days or even weeks for results. Use of real-time monitors could significantly reduce the risk of DPM exposure to miners, and available monitors have been shown to quantify DPM, mainly using the EC and other surrogates. The NIOSH Spokane Mining Research Division is conducting research aimed at developing a field-portable DPM monitor that is able to quantify both EC and OC. One part of this work is to understand the effect of OC on currently available real-time DPM monitors. This paper will present the results from experiments that were designed to observe the effect of OC on real time monitors and compare the results with the NIOSH 5040 method. BACKGROUND Diesel engines remain ubiquitous in mining environments and, as such, are one of the primary sources of ultrafine- and nano-aerosols in the mining environment in the form of diesel particulate matter (DPM). As a result of their small size, DPM has longer residence times in a mine atmosphere than the typically larger mechanically generated dust [1]. In addition, the small size enables DPM to penetrate deeply into the respiratory system [1], and exposure to DPM has been shown to contribute to various adverse health outcomes of the pulmonary system [2] and cardiovascular system [3]. Diesel exhaust has been classified as a carcinogen to humans (Group 1) by the International Agency for Research on Cancer [4]. Due to mounting concern about adverse health outcomes, extensive efforts are being made to reduce workers’ exposure to DPM, with the high exposures that often occur in underground mines being of particular concern [5]. New technologies are being developed to reduce engine emissions and thereby airborne DPM levels, including advanced engine technologies, a host of aftertreatment systems [6], and a variety of alternative fuels. The latter have been shown to markedly decrease respirable DPM and other hazardous components of diesel emissions from mining vehicles [7], yet high exposures persist, especially in underground mines [8]. In order to reduce worker exposures, it is critical to measure the levels of DPM in active work settings. In mine settings, exposures to DPM are measured by collecting air samples on filters (usually full-shift samples) and sending them to a lab for analysis using the Mine Safety and Health Administration (MSHA) P13 method, a variant of the National Institute for Occupational Safety and Health (NIOSH) 5040 method. The 5040 method is designed to quantify the mass of elemental carbon (EC) and organic carbon (OC) on the samples [9], which is then used to determine the concentration in the sampled air. MSHA has set a limit for exposure, which is based on the concentration of total carbon (TC), or the sum of both EC and OC. The allowable TC in the air (time-weighted average over the shift) is 160 μg/m3 of TC [10].

Jan 1, 2019

By W. R. Reed, S. Klima, J. Driscoll, T. W. Beck

"Tests were conducted to determine properties of four foam agents for their potential use in longwall mining dust control. Foam has been tried in underground mining in the past for dust control and is currently being reconsidered for use in underground coal longwall operations in order to help those operations comply with the Mine Safety and Health Administration’s lower coal mine respirable dust standard of 1.5 mg/m3. Foams were generated using two different methods. One method used compressed air and water pressure to generate foam, while the other method used low-pressure air generated by a blower and water pressure using a foam generator developed by the U.S. National Institute for Occupational Safety and Health. Foam property tests, consisting of a foam expansion ratio test and a water drainage test, were conducted to classify foams. Compressed-air-generated foams tended to have low expansion ratios, from 10 to 19, with high water drainage. Blower-air-generated foams had higher foam expansion ratios, from 30 to 60, with lower water drainage. Foams produced within these ranges of expansion ratios are stable and potentially suitable for dust control. The test results eliminated two foam agents for future testing because they had poor expansion ratios. The remaining two foam agents seem to have properties adequate for dust control. These material property tests can be used to classify foams for their potential use in longwall mining dust control. IntroductionAbout one-half of U.S. underground coal is produced by longwall mining, which allows for mining high volumes of coal but generates significant amounts of coal mine dust. This can lead to overexposures for longwall miners and possibly occupational respiratory diseases, including black lung and silicosis, which have no cure and can be disabling or fatal. The only method to avoid these occupational illnesses is through elimination of exposure to respirable coal mine dust and crystalline silica (quartz). The current occupational exposure limit for respirable coal mine dust is 1.5 mg/m3 during each shift that a miner is exposed in the active workings of the mine or in mine facilities (Mine Safety and Health Administration (MSHA), 2015a). When respirable quartz is present, the mine must maintain average concentrations at or below 0.1 mg/m3. If the mine exceeds the 0.1 mg/m3 respirable quartz dust concentration, then the applicable respirable dust standard is reduced, calculated as 10 divided by the percent quartz present (MSHA, 2015b)."

Jan 1, 2018

Placing a detonating explosive inside a volume of rock is an efficient method of rock fragmentation. The explosion generates internal tensile stresses in the rock, and because rock is a brittle material, this brings about crack propagation and fragmentation far more efficiently than does application of explosive on the surface. To get the explosive inside, we drill a pattern of boreholes and charge the explosive into the holes. This is really the one and only purpose of making blastholes in mining: to give access for the explosive to the interior of the rock. No matter how big and expensive a drilling jumbo we stand up in front of a rock face, and no matter how many boreholes we let it drill, the rock does not fall apart by itself without blasting. It is the action of the explosive in the boreholes that does it. When we consider that we need a pound or two of explosive for every cubic yard of rock to be fragmented, and a pint of borehole volume for each pound of explosive, we see that the process of blasthole charging is an important element in the whole process of rock blasting.

Jan 1, 1975