Search Documents

By E. P. Gustafson

Demand by precious metals explorationists for cost effective means to target subsurface geologic structures worthy of evaluation by means of drilling has led to the use of the predictor-correlator technique. To locate polarizable targets, the predictor-a localized inhomogeneity in electrical properties-is placed at various locations in the computer-simulated subsurface region, and correlated with the potential distribution observed in the field. The correlation coefficient obtained is assigned to the subsurface location. IP targets are extracted by calculating a second correlation section based on higher-frequency illumination and subtracting it from the first. The locations of correlation difference correspond to the locations of polarizable mineralization.

Jan 1, 1989

By D. Scott Scovira, Thomas Gustavsson

Exiting WW2, the potential of nitrates and hydrogen peroxide for application as industrial explosives both became known. The technology stream advanced the development and uptake of nitrate-based explosives to the point that they are the current global standard for blasting. Recently environmental issues are influencing the strategic agenda of extractive industries. The mid-2010s saw renewed interest in hydrogen peroxide explosives to eliminate NOx fume. Carbon reduction initiatives in the 2020s provided additional impetus to investigate hydrogen peroxide-based explosives. Hypex Bio is at the forefront of developing and delivering bulk gas sensitized Hydrogen Peroxide Emulsion (HPE) for blasting. HPE consists of hydrogen peroxide along with smaller amounts of fuel and emulsifier. The consistency of HPE is similar to industry- standard nitrate-based emulsions. It is compatible with existing priming and initiation systems. HPE does not contain nitrates and thereby does not produce post blast nitrous oxide fumes nor discharge of nitrates or ammonia to mine water. Importantly, HPE contributes to reduction in total carbon emissions as compared to nitrate-based explosives.

Feb 1, 2025

By D. M. Carris

Since the Buffalo Creek incident in February, 1972, Federal and state environmental agencies have had the pressure on the coal industry in the Appalachian area to close the coal processing plant water circuits. In an attempt to comply with this requirement, Eastern .Associated Coal Corp. decided to install a vacuum disc filter system at its Kopperston plant to eliminate the tailings pond and reduce the amount of plant make-up water. It was recognized at the time that the plant static thickener tailings would be a very difficult slurry to dewater because of its unusually high clay content. The following is a case history of the Kopperston installation and the refinements Eastern has made in its vacuum disc filter operation to increase efficiency.

Jan 1, 1979

By J. O. Guthrie

Newmont has delineated a 600,000+ ounce gold reserve in the Cargo Muchacho Mountains. This is a desert range underlain by Proterozoic(?) Tumco Formation (gneiss) intruded by Jurassic granitic plutons, and cut by low angle shears of the late Cretaceous Chocolate Mountain Thrust event. Gold, associated with pyrite, quartz veinlets, and propylitic alteration, is emplaced along low angle shears. The mineralizing system, enriched in tungsten, copper, zinc and arsenic, was active during Eocene time. Gold reserves are found in eleven areas as moderate to high tenor deposits that may be mined by open pit and underground techniques. Eastmaque Gold Mines Ltd. is developing the deposit.

Jan 1, 1987

By JÖRG DEHNERT, PETER WINDISCH, Bernd Schönherrt, JENS STOPP

The Quick-Erect Stopping System (QESS) offers a new way of reducing the radon exposures of miners in Germany, especially during remediation work in old mines. The QESS is a light-weight, modular, and reusable construction kit of interlocking telescopic aluminum tubes, radon-proof foil, and expanding foam. It is designed to seal off radon-rich parts of galleries within only a few minutes. Originally, the QESS was developed to protect miners against radon exposures. Then, the QESS found the attention of several mine rescue teams at a German mining conference. The Student Mine Rescue of the Technical University Bergakademie Freiberg and the Wismut Mine Rescue carried out firstmine rescue drills in Freiberg and Schlema. Additionally, a mine rescue drill was carried out by the Front Range Mine Rescue in the Edgar Experimental Mine of the Colorado School of Mines. These drills helped to improve the systemand highlighted its potential for mine rescue operations. Now, the QESS is wellsuited for small-scale mining. The QESS can be used to seal off galleries in only a few minutes to both protect miners fromradon exposures and to support mine rescue operations. Moreover, the QESS was also successfully used in ventilation experiments.

Jul 23, 2020

By Christopher B. Kapes

To reduce concentrate dewatering and drying costs, the Concentrator Division at Phelps Dodge Morenci, Inc. investigated available filtration technologies. Numerous methods were explored, including: drum, disk, belt, pressure, hyperbaric, and ceramic media filtration. An economic evaluation of the individual filtration technologies indicated the advantages of ceramic media filtration for Morenci concentrates. This paper discusses the technological development culminating in the first full scale application of ceramic media disk filters in North America. Low moisture contents are obtained at high production rates and greatly reduced operating costs.

Jan 1, 1994

By Robert J. Wright

The purpose of this paper is to propose a classification of uranium deposits that is believed to be well suited to the needs of uranium exploration and resource assessment. By way of background some observations are offered about mineral exploration in general, and uranium in particular. Attention is first given to the we of models in mineral exploration. Some general principles of mineral deposit classification, the basis for model formulation, are then considered. Finally, the uranium classification is presented.

Jan 1, 1979

By Roy H. Paddon

This paper describes the 6, 000 tpd, three stage haulage system at the Ozark Lead Company's mine in southeastern Missouri. It details the methods and problems pertinent to the loading, hauling, sorting, crushing, storing and hoisting of waste rock and ores obtained from underground development headings and production areas. The Ozark Lead Company is a wholly owned subsidiary of the Kennecott Copper Corporation. Its mine is located nine miles south of Bunker in Reynolds County at the south end of the "New Lead Belt" mining district. Development started in May, 1964, by drilling a seven foot diameter (six foot cased), 1, 250 foot development-ventilation shaft. Drifting began in August, 1965, to obtain a bulk ore sample, to test ore continuity, and to drive two mine levels while the pre-grouted production shaft was being sunk. Over 7, 900 feet of 12 by 24 foot drifting was done from this small shaft. In March, 1966, a 20 foot diameter, three compartment, concrete lined production shaft was collared. It intersected existing development headings at a depth of 1, 195 feet in April, 1967, and was completed along with a concentrator and other facilities in June, 1968. Mine production began that month, with 5, 000 tpd reached in 1970.\

Jan 1, 1971

By R. Guardia, J. Hoskins, E. Claros, Y. Kamiya, R. Ramirez, J. Dalenz, P. Fernandez, E. Ilgren

Crocidolite is a well known causative agent for mesothelioma. Studies have shown that the pathogenicity of the fiber from different mines varies considerably and it has been postulated the parameter that appears most likely to account for this variation is fiber width. Epidemiological studies have shown that ‘thin’ fibers from mining areas of Western Australia and the Cape Province, in South Africa are associated with a high mesothelioma risk while exposure to ‘thick’ asbestiform amphibole fiber of the same fiber type are associated with little or no mesothelioma risk. This study is concerned with ‘thick’ Bolivian crocidolite but similar findings also probably explain the paucity of mesotheliomas in the Finnish anthophyllite, South African amosite and African Transvaal crocidolite mines. The findings from the present study suggest the incidence of mesothelioma in the three major cities of Bolivia is not significantly elevated above background even though Bolivian crocidolite has been used for the past 60 years commercially and residentially in all three cities. Although some cases of mesothelioma may have been missed due to a failure to reach hospital or a shortened natural lifespan, mesothelioma generally occurs after the age of 50, we cannot tell precisely the extent to which these were confounding. We suggest the most likely explanation for the lack of mesotheliomas despite the large populations at risk from the long and extensive residential and commercial use of crocidolite containing products, is related to an increased fiber width distribution and a concomitant reduction in the ‘Stanton fiber size’ fraction.

Jan 1, 2012

By Raymond A. Bradbury

Martin County Coal Corporation operates three underground mines and two surface mines on Wolf Creek in Martin County near Inez, Ky. The original underground development was begun in March of 1970. The property being developed is leased from Pocahontas Land Corporation. The A. T. Massey Coal Company, whose offices are located in Richmond, Virginia, is the parent company and sales agent for Martin County Coal. Duke Power Company is the customer who will take all the production from the mines which ultimately are scheduled to produce 2,500,000 tons annually. The Norfolk and Western Railway Company built a 24-mile railroad into this huge reserve of low-sulfur steam coal. Four coal seams, all above drainage, are included in the lease. The Middle Coalburg and Stockton seams are being deep-mined now and it is in three mines that the diesel haulage equipment is used. Those of you who attended the AIME meeting in Birmingham last October or the Diesel Symposium in Pittsburgh in January of this year are familiar with the introduction of trackless diesel-powered haulage equipment into our Martin County mines. I made a presentation at each of those meetings which dealt with our first experience with Wagner Mining Equipment haulage units. These machines are sold exclusively by Lake Shore, Inc. whose offices are in Iron Mountain, Michigan.

Jan 1, 1973

By A. Adhikari, P. Tukkaraja, S. Jayaraman Sridharan

Shafts are critical components of the mine ventilation systems and contribute significantly to the mine ventilation pressure. Estimation of shaft pressure losses is an important aspect of mine ventilation planning and shaft frictional pressure losses are extensively studies. Shock losses contributed by shaft buntons are estimated using the interference factor model developed half a century ago. This study aims to develop a better performing prediction model for shaft buntons using state of the art experiment and numerical data, and machine learning techniques. Results show that the present prediction model is performing poorly, and the prediction performance can be improved by incorporating additional predictor variables. The Artificial Neural Network standardized Machine Learning model developed in this study is able to predict the shaft bunton shock loss with high accuracy (R2 = 0.956).

Jun 25, 2023

By J. Oliver, J. Cleason

"With maintenance costs rising and an increasing demand for higher production, the use of sealed spherical roller bearings can reduce maintenance costs while providing increased production uptime. The sealed spherical bearing has increased bearing life by slowing the ingress of contamination. This paper will describe how contamination and bearing wear is reduced by reviewing case histories from coal and metal mines that improved their production by decreasing downtime using sealed spherical roller bearings. INTRODUCTION The spherical roller bearing (SRB) is a robust rolling element bearing that can accommodate high radial loads, low to moderate axial loads, and misalignment with no loss in carrying capacity. (i.e. Figure 1) Because of these characteristics, it is a favorite in mining applications and many other heavy industry applications. Primary applications are the various pulleys on conveyors. Coal and hard rock mines have hundreds of miles of conveyor lines and countless head, tail, drive, and idler pulleys. Maintaining the bearings on these pulleys and replacing bearings that have failed can be a huge expense to a mine in components, labor and downtime. Ideally, the bearings are replaced when the pulley is changed out according to the maintenance cycle, about every 4 years. Reality, however, causes the bearings to be changed out every year, or sooner. These premature bearing replacements can cause production shut downs for as long as 8 hours. Conveyor pulleys have been targeted at many mines as the single biggest maintenance pain point.The primary reason for replacing conveyor bearings is internal wear from fine, solid particle and water ingress through the bearing housing seals. (i.e. Figures 2 & 3) Traditionally, the bearing is mounted in a split pillow block housing (SAF, FSAF, SDAF or SNL are typical industry styles) with only labyrinth seals (LER/LOR) for protection against the ingress of contaminants. The bearings are lubricated with grease. A common way to extend the MTBR is to purge the bearing system with large quantities of grease to flush out the contaminants. If the bearing, and thus the housing seals are not frequently purged with grease, fine solid contaminants enter the housing and bearing through the labyrinth cavities."

Jan 1, 2015

By R. J. Zagrocki

Rekindled public concern about lead toxicity has intensified the awareness of lead-bearing materials in contact with the environment and the human population. Lead's common association with other metals makes the increasingly restrictive lead standards a primary concern for a large number of metal and metal-related industries. In commercial scale demonstration tests with lead-bearing wastes, the HRD Flame Reactor process has a demonstrated ability to separate and recover over 95% of the lead as a recyclable oxide, while rendering the remainder of the material as vitrified, non-leaching, and nonhazardous co-product. Recent Flame Reactor process tests and preliminary cost data for secondary lead soda slag are highlighted.

Jan 1, 1992

By Richard C. Corson

The new 9300 TPD sinter plant being built for China Steel Corporation is incorporating the latest computer technology for plant control systems. The control system will use a central computer and distributed micro-processors to control instrument loops and switching logic in the blending yard and sintering plant. All plant functions, including combustion and fan controls, will be controlled by remote microprocessors located throughout the plant, and connected by a communications link to the centrally located computer and control room. The design, programming, construction and operation of a microprocessor based control system presents new challenges to the control engineer. With microprocessors in the control system, more power exists in the individual control loop and many supervisory functions may be added at the loop level. The specification of the microprocessor system and the resolution of hardware design and control system design can lead to development of powerful systems capable of higher level control and optimization functions

Jan 1, 1981

By G. W. McMahon

Following the Sago Mine accident, the U.S. Mine Safety and Health Administration (MSHA) asked the U.S. Army Engineer Research and Development Center to study several possible methane explosion scenarios in the Sago coal mine. The study used a 0.3-m (1-ft) resolution map of the mine to produce a 3-dimensional (3 D) model of a portion of the mine, including the sealed area where the explosion occurred. An advanced 3 D computational fluid dynamics (CFD) code was used to calculate the explosion pressures within the sealed area, on the mine seals and in nearby regions of the mine. Based on the best available information on methane concentrations and assumptions on homogeneity and on layering and mix composition, three separate initial conditions of methane-air concentrations and location were studied. This paper discusses the CFD modeling technique, the results of the calculations, the challenges of conducting this type of modeling and the advantages and limitations of CFD modeling of accident investigations of mine explosions.

Jul 1, 2010

By Erika Moonin, Jim Nickerson, Claudio Cimiotti, Roberto Bono

"In response to the severe drought on the Colorado River basin and in order to preserve existing water capacity to the Las Vegas Valley, the Southern Nevada Water Authority contracted a new deep-water intake (Intake No. 3) located in Lake Mead. The current project (Contract No. 070F-01-C1) includes 5 km (3 miles) of tunnel with very difficult geological conditions and a 200- m (650-ft) deep shaft and marine works. This paper will present the current status of the design-build contract being constructed by Vegas Tunnel Constructors and the challenges and problems faced and the innovative solutions developed to handle the difficult conditions encountered during tunneling with up to 15 bars of pressure.ProjectbackgroundThe Las Vegas Valley receives the majority of its water from Lake Mead, which is located approximately 30 km (20 miles) east of the Las Vegas, NV metropolitan area. Due to the severe drought that has hit the southwest region of the United States, the water level in Lake Mead has receded from its high water level of 372 m (1,221 ft) above mean sea level (amsl) to a low of 330 m (1,076 ft) amsl in June 2015. Should the lake level continue to fall, at elevation 320 m (1,050 ft) amsl, the current water intakes will not be able to draw enough water to meet the needs of the local area. The risk of losing water capacity has prompted the construction of a new deeper intake. Not only is the new Intake No. 3 situated at a lower elevation in the lake at 262 m (860 ft) amsl, the new Intake No. 3 is also located to draw better quality (Fig. 1).Project challengesThe project has had several difficult challenges to overcome:• The work consisted of a 1.2 kt (1,300 st) structure constructed on a barge and lowered 100 m (330 ft) into Lake Mead anchored with 9,200 m3 (12,200 cu yd) of tremie concrete.• The drill-and-blast starter tunnel was impacted by three inflow events, resulting in a one-year project delay.• One of the main challenges was selecting the tunnel boring machine (TBM) and excavating the tunnel with expected hydraulic head pressure of as much as 17 bar (16 bar was the highest pressure recorded during the drive), crossing faulted areas, low rock cover and the risk of tunnel instability due to direct connection with the lake.• Extensive pre-excavation grouting with a constant head pressure ranging from 12 bar to 15 bar.• Structural repair of the cutterhead in difficult hydrogeological conditions [water inflow of approx. 800 m3/hr (4,000 gpm)].• Complete repair of the cascade sealing system for the main bearing and two replacements of the pinion bearings.• The TBM approach to the intake structure."

Jan 1, 2015

By L. Xiao

Using K-oleate as a collector and alizarin red S (ARS) as a modifying agent, selective depression of dolomite from francolite was achieved in alkaline medium (pH> 9.0). Interestingly. ARS was also found to depress igneous apatite in alkaline medium in oleate flotation of apatite and calcite. Adsorption of ARS alone on dolomite was found to be higher than that on francolite. Complimentary adsorption experiments of ARS and K-oleate showed that oleate adsorption was increased in the presence of ARS on francolite but not on dolomite. K-oleate adsorbs on both francolite and dolomite and causes precipitation of calcium and magnesium oleate. Such precipitates can be pre-vented when ARS is present. The results are explained in terms of competitive adsorption for the active sites on francolite and dolomite by oleate and ARS, and their interactions with dis-solved mineral species in solution.

Jan 1, 1988

By Ted H. Eyde

Improving the mineral industry's tarnished image describes in a nut- shell the reason why the Speakers Bureau of the Tucson Subsection of the AIME was formed. Let's go back in time about 3 years to the fall of 1971. Literally thousands of bills detrimental to the mineral industry were being introduced into Congress and State Legislatures. Unfortunately, many were being passed and signed into law. Clean air and water, zero pollution, preserve the environment, ecology, biodegradeable, wilderness were the words that the self- styled ecologists and environmentalists were preaching. The mineral industry either sat mute or in place of acting, reacted in a way certain to attract a maximum amount of bad publicity with a minimum amount of rhetoric. A mining company president, for example, commenting on the primary air standards in Arizona was reported by the press as having said, "we'll shut all the smelters down and put thousands of Arizonans out of work if we have to meet the Arizona standards." Or another defending a poorly planned highly visible open pit nonmetallics operation, "we'll take the whole mountain down if we want to, and nobody can stop us" and still another manager of Operations, "the bottom line is all that counts, to hell with all of this environmental nonsense."

Jan 1, 1975

By L. A. Baker

The presence of goethite in a hematite ore has been shown to strongly affect the time of heating to the firing temperature. The investigation of spalling of single pellets and of packed beds has enabled free water and goethite spalling to be identified as separate phenomena. In addition, it has been shown that even for an 18 inch deep bed of green balls the free water and goethite drying periods can be considered separately. Based on this observation, a method of predicting production rate and hood temperature profile is presented. The method required knowledge of the ore goethite content, ore grind and the green pellet bulk density. Laboratory results were found to be in good agreement with actual plant practice and have led to improved process performance.

Jan 1, 1972

By Charles Bruce

Three years ago, at a reception given during the Steel Institute meeting in New York, I heard the remark, "A new formula must be found for foreign investment." This was immediately following the takeover of U. S. Steel's Matilde operation in Bolivia. Recently, at the World Mining Congress in Lima, Peru, the subject of foreign investment was still a lively topic of conversation. The nationalization of the copper mines in Chile and recent trends in the "Third World" have made all but a few extremely wary of investment anywhere other than in the ?stable? countries. Now, the fallibility of this philosophy has been demonstrated in such "stable" countries as Canada, Australia, and Ireland. Yet, nationalization is not new to us. The events in Chile were classified as disastrous to the affected companies, but so were the effects of nationalization to the majors in Bolivia in 1952. Mexicanization of the mining industry in Mexico was considered impractical by many. Now, those who accepted it are finding it to be workable.

Jan 1, 1975