Search Documents

By F. Gonzalez, A. Zambrano, J. Schwoebel, S. Kravits

Significant lost time delays were experienced by Carbonifera de Nueva Rosita, S.A. de C.V. ("CNR") during mining development of the Pasta de Conchos Mine ("the Mine") near Nueva Rosita, Coahuila, Mexico. Furthermore, methane gas concentration in the return air course had exceeded 1.0 percent. Resource Enterprises, Inc. ("REI") was contracted by CNR to recommend an approach to reduce methane emissions at the Mine. In order to recommend a degasification approach, REI and CNR obtained geologic and reservoir characteristics of the Double coal seam, Olmos Formation. A vertical core hole was drilled to obtain core samples to determine gas content (average 8.4 cm3/gm) and to conduct a slug test to estimate permeability (34 md). This information was used to simulate gas productivity and drainage effectiveness. The simulation indicated that underground horizontal boreholes would remove significant quantities of gas in advance of mining in a reasonable period of time. Based on the results of the simulation study, an underground degasification drilling program was initiated at the Mine. In a six month period, five long in-mine degasification boreholes were drilled in advance of CNR's three to five years mining projections. Peak gas production from the five boreholes (approximately 2,750 cumulative meters) had exceeded 45,000 m3/D. Results to date have indicated a general reduction in methane concentration in the return air course below 0.8 percent.

Jan 1, 1993

By Fritz F. Prugger

This paper considers some of the main aspects of underground mining in the flat, rich, but deep lying deposits of Saskatchewan. It briefly describes the pertinent geological features as they relate co mining and the practical de-stressing techniques used to allow productive extraction in the high stress environment present in many of the province's mines. Fining layouts, materials handling and the evolution of some of the world's largest mining equipment are examined.

Jan 1, 1980

By G. M. Swinkels

It is generally accepted, that oxygen is a necessary reagent for the flotation of galena with xanthate. Recent measurements have shown (1) that under plant conditions oxygen may be in a short supply to the extent that it limits the rate of flotation. Thus, it becomes important to define the exact role of oxygen and establish a model for the rational design and control of flotation separations, involving oxygen as a reagent. All theories or, the flotation of galena assign oxygen the role of an oxidant. However, they disagree on a number of questions: 1) Is the galena or the xanthate being oxidized? 2) Is a lead dixanthate or dixanthogen the actual collector? 3) Is the oxidation process in which oxygen participates of a chemical or an electrochemical nature? The last question arises from the observation (2) that an anodic bias as well as oxygen will make a galena surface hydrophobic in the presence of xanthate. Theories which are based an the premise that the influence of oxygen is of an electrochemical nature offer elegant models of galena flotation. However, full advantage has not been taken of available electrochemical techniques to discriminate between theories and this is the area towards which this research has been directed (3).

Jan 1, 1970

By Sandeep Kumar Jeripotula, Govinda Raj Mandela, Aruna Manglapady

The main aim of this work is to evaluate whole-body vibration (WBV) of dozer operators based on three sitting postures (i.e., with 15° lean forward inclination posture, vertically erect posture with no inclination, and with 15° lean backward inclination posture) in Indian surface coal mines. A seat pad tri-axial accelerometer was used to collect WBV data from six dozer operators for three different sitting postures. Results showed that except for Dozer-1, 2, 4, and 5 operators during lean forward sitting posture and Dozer-4 operator during vertical erected posture, no other dozer operators have exceeded an exposure limit value (ELV) of 1.15 m/s2 in any of the considered sitting postures. Similarly, the vibration dose value (VDV) based on exposure action value (EAV) of 9.1 m/s1.75 has surpassed for all the dozers. But no dozer operator has exceeded an exposure limit value of 21 m/s1.75. The outcome of the study infers that based on “above health guidance caution zone (HGCZ)” for daily vibration exposure, i.e., A(8) measurements, for the operator sitting in lean backward postures the vibration amplification was reduced by 32.89% less compared with lean forward posture and 16.23% less when compared with vertically erected posture. Similarly, based on VDV(8), the exposure to vibration for the lean backward posture was reduced by 33.34% when compared with lean forward posture and 17.11% less when compared with vertically erected posture. Based on the above observation, it is concluded that lean back inclination with a trunk flexion of 15° is a favorable sitting posture, as it exposes the dozer operators to minimum vibration.

By Graham Davey

High-speed stirred milling is a relatively new method of grinding in the metalliferous process industries. However, it has been widely used in the industrial mineral field for more than 30 years. Many existing metallurgical operations are looking to maximize economic return from existing deposits this requires new thinking and technologies. The operating experience of two copper operations is discussed here to show the effect of the introduction of the Metso Stirred Media Detritor (SMD), a new type of high speed stirred mill. Both operations have derived significant metallurgical benefits from this new technology. The benefits and process difficulties are explained. The initial drive in high speed stirred milling technology was toward ultra fine grinding where the mill product has an 80 percent passing size of 15 µm (937mesh) or less. More recently, a number of installations have occurred in a more conventional regrind setting. Few conventional copper concentrators require such fine grinding to attain satisfactory copper grades and recoveries. So other advantages must be considered here rather than just the ability to grind fine with good power efficiency.

Jan 1, 2004

By A. Chieregati

"A heterogeneity study was conducted at Erdenet Copper Mine in Erdenet, Mongolia, to determine the fundamental sampling error associated with blasthole sampling. Using a custom designed sector sampler, six large blasthole samples were collected to perform the test that was developed by Pierre Gy, to estimate the constitutional heterogeneity factor for several types of ore. The study investigated the entire sampling protocol, from mine site to analytical laboratory, and quantified the contributions to fundamental sampling error (FSE) of the various stages of sampling and sample preparation. The total relative standard deviation (RSD) of sampling error was determined to be ±32% and ±49.4% for copper and molybdenum respectively. A classical statistics analysis conducted on the data confirmed the level of RSD. About 95% of the sampling error was produced from only one step in the sampling protocol: when the 1 kg sample was reduced to 50 g sample for chemical analysis. Therefore, it is recommended that the 1 kg sample be reduced to 50g using a slightly different protocol to minimize the FSE. The 1 kg sample should be first crushed to 0.2cm size. A 250g split should then be taken and fine ground. A 50g split should then be taken from the 250g fine ground split. These two simple steps will reduce the FSE to ±7.9% and ±17% for copper and molybdenum respectively. The modified sampling protocol effectively reduces the probability of misclassification of low grade ore to zero. INTRODUCTION The Erdenet copper-molybdenum open pit mine is located in Erdenet, in Orkhon province, Mongolia. The Erdenetiin-Ovoo copper-molybdenum deposit is between 1.5 and 3 km wide, and about 25 km in length (Erdenet Mining Corporation, 2016). Chalcopyrite, bornite covellite and chalcocite are among the major minerals found in the deposit. The mine processes approximately 26 million tons of ore annually. A study was conducted to evaluate the fundamental error associated with the blasthole cuttings and sampling protocol at the mine. The open pit mine uses 215mm diameter Russian drills to drill 17.5m holes for 15m benches. The total weight of blasthole cuttings for a 215mm diameter hole and 15m bench height is between 1.5 and 2 tonnes. This amount of sample is difficult and time consuming to collect and analyze. Therefore, a sector sampler was designed for the Russian drills to collect large samples that were representative of the blasthole cuttings (Ganguli et al., 2016). In order to eliminate the delimitation and the extraction errors, researchers consider sector samplers to be ideal for sampling blastholes (Pitard, 2008; Chieregati and Pitard, 2009). This method was intentionally more rigorous than the blasthole sampling protocol at the mine to ensure that the blasthole cuttings were properly sampled. This study was part of a broader study that also looked at the relationship between particle size and grade. The samples collected by the custom designed sector sampler were very large (195 kg on average), and therefore, sufficient for both studies. The relationship between particle size and grade has been reported in Ganguli et al. (2016)."

Jan 1, 2017

By B. K. Parekh, Z. Chen

INTRODUCTION The need for cleaning and recovery of fine (minus 28 mesh or 0.5 mm) coal fraction has increased in recent years. This results from realizing a substantial recovery of ultraclean coal from the waste stream improving overall Btu (heat) recovery, providing extra revenue for the coal industry. Also the potential of using the clean coal so obtained for making coal-water mixture which could replace oil. An additional benefit of recovery clean coal from the waste stream is reducing environmental concern of burning uncleaned coal and in waste disposal. Deashing of coal by physical beneficiation processes is limited by the degree to which ash components are liberated from coal. Conventional processes have been inefficient in terms of Btu recovery, for ultrafine coal. Chemical cleaning methods, which involves leaching of ash material from coal, have provided ultraclean coal at high Btu recoveries, are more costly than the physical cleaning methods. An advanced physical separation technique that appears to address the need discussed above is selective flocculation. This technique which has been successfully utilized in iron ore beneficiation offers the potential of processing fine and ultrafine coal to produce a clean fuel. OBJECTIVES The main objective of the present study is to investigate applicability of selective flocculation technique for recovery of clean coal product from the waste coal slurry supplied by the Peabody Coal co., from their three different coal preparation plants. It is also the objective of the program to conduct preliminary economic study of the selective flocculation process.

Jan 1, 2002

By S. D. Hill, G. E. McClelland

To maximize productivity and improve minerals processing technology, the U. S. Department of the Interior, Bureau of Mines, is investigating a particle agglomeration technique as a means of increasing the percolation rate of leaching solutions through heaps of clayey or finely crushed, low- grade, gold-silver ores. Bench-scale and pilot-scale experiments conducted on different ores indicated that the percolation rate of cyanide leaching solution was enhanced markedly by mixing the ore with a binder, such as lime or portland cement, moistening the mixture, then mechanically agglomerating and aging the feed prior to heap building and leaching. In addition, the rate of silver and gold extraction markedly increased without sacrificing total recovery of values. The use of concentrated cyanide solution instead of water during the agglomeration procedure substantially decreased the leaching time required to obtain maximum recovery. Results from bench-scale and pilot-scale experiments using the particle agglomeration technique are discussed.

Jan 1, 1981

By Jerry C. Tien

Mining in China dates back at least 4,000 years. Today, with no less than 103,000 metal/nonmetal mines and between 40,000 to 80,000 coal mines, China’s mining industry is undoubtedly the largest in the world. Despite improvements in recent decades, seemingly endless mining accidents continue to make the news. Official coal mining deaths were 6,702 in 2003, and 6,027 miners died in 2004; actual figures may be much higher. Added to these were the 2,699 deaths in the metal and nonmetal industries. Most of these accidents were due to CH4 (methane gas) explosions and fires as a result of inadequate mine ventilation de-sign or practices. A good portion of these accidents occur in small, privately run and often technically illegal mines. During the past 10 years, the Chinese government has attempted to crack down on small and often technically illegal mines without much success. The number of accidents and associated fatalities has not significantly reduced. However, there appears to be a new urgency in China’s efforts to step up mine safety in the country. After its worst reported mine disaster in more than a half century, the government quickly paid reparations to families, suspended high-level officials in charge and announced additonal reforms. One of those was the elevation of the central government’s work safety office to cabinet-level status. There has been increased transparency in reporting and investigation of mine accidents and disasters in recent years. There has also been an increase in public criticism by labor leaders concerning the neglect of mine workersafety.1 This article examines the causes of China’s many mining accidents, current legal and enforcement structures, respective mining health and safety related laws and regulations, recent mining industry developments and the latest effort to curtail small mining operations.

Jan 1, 2005

By M. I. Al-Wakeel

Nile sediment was collected as a waste from one of the water treatment plants in Cairo, and subjected to petrographical investigation and granulometric, chemical, and mineralogical analyses. It was expected to find diatomite in that sediment but it was a surprise to find that the diatomite content amounted to about 52.01% by volume in addition to quartz, orthoclase and clay minerals. The latter are represented by montmorillonite and illite minerals. The sediment is light gray in color, soft and has low density and high surface area, such density and surface area generally decrease with temperature. The sediment absorbs 317% of its weight in water. The diatomite skeletons are the main factor responsible for its high porosity producing microporosity and low density, and these particles are concentrated in the very fine silt size fraction (11x2µm). The common diatoms in such sediment include Cyclotella ocellata Pant, and Melosira granulata (Ehr.) Ralfs. It seems that this Nile diatomaceous sediment has many advantages over the fossil diatomite, such as Fayium diatomite in Egypt, with the absence of carbonate minerals that require grinding and calcination those cause destruction of the cellular structure and energy consumption. This Nile diatomaceous sediment can be processed using sequential classification to obtain diatomite concentrate of 88.8% grade at 90.6% recovery, and a middling product of 19.4% grade and 5.8% recovery. The suggested flow sheet is quite simple to produce diatomite product for different industries at a low cost. The unusual particulate structure and chemical inertness make diatomite an ideal mineral to be used as functional filler in a wide range of industries, and as catalyst carriers and insulating material. Key words: Egypt, Nile sediment, Diatomite, Beneficiation, Sedimentation, Classification.

Jan 1, 2008

By Daniel R. Stewart

The function of the geological engineer is to assist in mine planning and operations by collecting, interpreting, and applying geologic data to the solution of engineering problems. The geologist supports this effort by collecting additional geologic information specifically useful to the engineer. This use of geologic information reinforces the value of mine geology to the mining process beyond the traditional role of orebody definition. Work discussed includes: evaluation of caving strategies at the Climax and Henderson mines; support definition and slope stability at the Climax mine; and some uses of geology in cavability estimation for the Mount Emmons project.

Jan 1, 1983

By Joseph W. Siefke

The Kramer borate deposit is located in the western Mojave Desert at Boron, California, about 100 miles northeast of Los Angeles (Figure 1). The deposit derives its name from the district in which it lies. Borax (Na2 B407.10H2O) is being mined from the Boron open pit to serve a major portion of the United States and world borate markets. This paper deals primarily with those geologic factors which affect slope stability in the overburden at the Boron open pit. Discussion includes slope failure history, slope monitoring techniques and the results of a dipmeter survey of overburden structure. Open pit mining was begun at Boron in 1957. The initial pit was successfully excavated at the recommended 1.5:1 (horizontal to vertical) slope in the overburden. During pit expansion in 1962, excavation of the overburden exposed beds dipping into the pit at +15 degrees and numerous high angle fractures associated with two intersecting fracture systems, the West Jenifer and Portal fault zones. Ensuing south and east wall failures indicated the need for more structural information in the arkose to establish better wall design criteria. Barnard and Kistler (1963) recognized that the many facies changes, faults and other variables in the Boron overburden make it extremely difficult to reduce prediction of slides to a simple arithmetical formula. Despite the difficulties and uncertain¬ties, special programs such as surface resistivity, refraction seismic and core drilling were conducted in an attempt to predict slope stability conditions and to gather geologic information. These early efforts while helpful, did not provide the necessary details of bedding orientations and fault locations which are of paramount importance in our slope stability program. A dipmeter survey in 1974 successfully measured these variables and data from that survey are instrumental in the design of slopes currently being excavated.

Jan 1, 1976

By John M. Karpinski

A method and equipment have been developed Tor measuring the impact strength of grains of brittle materials. It is shown that brittle materials develop a characteristic particle size distribution when fractured by impact. A simple mathematical model has been found to describe this distribution, and one of the parameters of the model has been designated the r value. The r value is directly proportional .to impact energy and, for fixed impact energy, it becomes a useful criterion of grain strength. Data are presented on the variation of the r value as a function of sample history, initial size, energy input and number of impacts, The results are interpreted in terms of the flaw theory of brittle fracture.

Jan 1, 1964

By Brendan Reilly, Jon Isaacson, Paul McDermott

Kenny/Shea JV is constructing the water intake tunnel for the new Elm Road Generating Station, a supercritical coal-fired power plant in Oak Creek, Wisconsin, being built by Bechtel Power Corporation. The intake tunnel system consists of a temporary mining shaft, pump house and intake channel riser shafts, and four lakebed intake shafts. An 8.33 m diameter, 2,800 m long TBM mined rock tunnel is being constructed to connect the shafts. The intakes are located 2.4 kilometers offshore in Lake Michigan. The shafts and tunnel are being constructed in glacial tills and Silurian Dolomite. The estimated tunnel completion is December 2007.

Jan 1, 2007

By R. Feenstra

In the course of time, an increasing number of investigations on jet cutting all kinds of material, such as rocks1, 2, 3, metals4, 5, and wood6 have been reported to serve various applications. This paper deals with one particular application of jets, viz deep-well drilling for hydrocarbon exploration and production. A number of papers have been published on this subject 7, 8, 9, some of which refer to jets purposely containing abrasives, termed 'jetted particle drilling'7. Since such abrasives complicate fluid handling considerably and do not appear to be absolutely necessary for making hole we have restricted ourselves to conventional drilling fluids. A large part of our investigation has been performed with the aid of three laboratory-type drilling machines, which permit tests on both micro-bits (12 in) and full-scale bits (62 - 9 5/8 in). In view of the application of jets in deep wells, care has been taken to simulate hydrostatic pressures as they exist in the field on the hole bottom. These have been found to have a major effect on the bit-penetration rate for various drilling fluids. Following experiments with single nozzles, laboratory bits have been designed, improved further and developed for field use. Field runs on 9 5/8 in bits, using conventional equipment and pumps, served to verify the feasibility of the jet drilling concept. Further efforts are evidently needed to evaluate the jet drilling method. It is encouraging that one of these10, a field test programme, is supported by a number of oil companies jointly. Such a combined effort is of paramount importance to evaluate and develop this new method of drilling to its full potential in a reasonable period of time. This paper aims to contribute to that ultimate goal.

Jan 1, 1974

By Elliot Gillerman

The title of this paper implies the presence of silver, nickel, and cobalt minerals at, the Alhambra mine. Perhaps this should be amplified to include uranium, as pitchblende also occurs, possibly in mineable quantifies. A brief history of the Alhambra mine is of interest, both from a historical angle and as pointing up the importance of geology in the-present development. The Alhambra is one of several mines in the Bullards Peak or Black Hawk dis¬trict, ass it is more familiarly known, in southwestern. New Mexico, which was mined for silver in the 1880?s and 18901s, Silver valued between $500,000 and $1,000,000 was extracted from the mine in the 10 years prior to 1893, when operations ceased. Almost all the silver mined was native silver, although a small quantity of argentite was produced. Nickel and cobalt were recognized in the ores, but they were thought to be of no consequence.

Jan 1, 1959

By H. S. Castro

The by-product molybdenite technology in Chile is reviewed. Flowsheets, reagents and some operation features for the actual six Chilean moly plants(Chuquicamata, El Teniente, El Salvador, Andina, Las Tortolas and Pelambres), are presented. The chemical and physicochemical factors involved in the depression of copper and iron sulfides during the selective flotation of molybdenite, with sodium sulfide, sodium sulfhydrate, anamol-D and LR-744, are discussed. Advances in technology to solve problems of excess of lime (precipitation with sulfuric acid); excess of residual flotation reagents (activated carbon and kerosene); and optimization of depressant consumption (Eh control, nitrogen and low-oxygen air), are discussed.

Jan 1, 1998

By Anshumali Gangwar

This paper outlines the chance constrained binary integer program developed by the author in his doctoral dissertation at Columbia University, New York, 1973. The optimum planning of a mining program involves the determination of a production schedule which maximizes the net present value of the mining property. The actual mining process has an inherent stochastic and discrete nature. In particular, the demand for the mined product and the grade of the mineralized material in the ore are the two most important stochastic mining variables. The decision to mine or not to mine any block of a mining property is a binary integer variable. This paper outlines the formulation of pit production scheduling problem as a chance constrained binary integer program. The deterministic equivalents of these chance constraints are nonlinear in binary variables which have subsequently been linearized. The planned objective is to meet with a stipulated high degree of reliability, all the random demands as they materialize with a random supply of the commodity being marketed as determined by the eventuating random grade values of the exposed ore blocks and the mining system's production constraints such that the discounted total production costs over the entire planning horizon are minimized or the profits maximized. The emerging surface of the mine in each scheduling period is determined by the values taken by the binary decision variable associated with each block of material in each scheduling period.

Jan 1, 1982

By Thomas P. Mucho, Dennis Dolinar, Christopher Mark

Horizontal stresses are caused by global plate tectonic forces. During 1995 alone, they were largely responsible for closing two U.S. longwall mines. This paper presents six case histories from Pennsylvania. West Virginia, Kentucky and Alabama. In each case history, a mine encountered roof falls or difficult ground conditions in the headgate, caused by horizontal stress concentrations. The problems are detailed and the control measures adopted are described. In most cases, nearby longwall panels without stress concentrations were trouble-free. The paper also discusses detailed measurements made at two adjacent Pennsylvania longwalls. One headgate was oriented to avoid a horizontal stress concentration, and the other was not. Eliminating the stress concentration dramatically reduced roof support loads and roof deformation. The paper concludes that proper panel orientation and sequence is the key to maintaining headgate ground control. The optimum orientation is not parallel with the maximum horizontal stress, as previously thought but rather 200 in the stress shadow of the gob. Other stress control techniques, including artificial support, are briefly discussed.

Feb 24, 1997

By A. Mayton

The prolonged exposure of equipment operators to shock and whole-body vibration (WBY) is linked to cumulative back, neck, and abdominal disorders. In low-coal mines, space restrictions make seat suspensions difficult to use in isolating operators from shock and WBY. Researchers at NIOSH, Pittsburgh Research Laboratory, are responding to these issues by investigating viscoelastic foams. For the full-load case. an ergonomic seat with viscoelastic foams isolated the shuttle car operator from shock at 15Hz. Researchers used results from additional foam testing with an analytical model to identify viscoelastic foams that provide shock isolation at a frequency below 5 Hz.

Jan 1, 1998