Search Documents

By T. C. Eisele

The use of column flotation was considered for the ?reverse flotation? of iron ore, where the gangue (quartz) was recovered in the froth product. This use of the froth for carrying the gangue mineral rather than carrying the valuable concentrate significantly changes the operational requirements of the column. The objective of this work was to determine which of several column flotation technologies would be most suitable for this type of flotation operation. Studies were carried out using both the Jameson column and the Deister column. Comparative results are presented that show the capabilities of both column types in this application relative to conventional Wemco flotation cells. Columns were demonstrated to have grade-recovery performance superior to what could be achieved with conventional cells. Two-stage flotation with the columns could produce a concentrate that was up to 70.2% Fe at 87.5% iron recovery, compared to 70.4% Fe at only 77.7% iron recovery for four stages of flotation in conventional cells. It was shown to be particularly important to operate the columns to recover a maximum of the quartz gangue into the froth. It was noted that there are often problems in scale-up of laboratory columns to plant scale, because the increase in height and the decrease in the ratio of height to diameter at the larger scale allows more axial mixing and bubble coalescence, both of which degrade the column performance. Horizontal baffling was shown to improve column performance by reducing axial mixing and breaking up large bubbles, and so the use of such baffles in the reverse flotation application was investigated.

Jan 1, 2007

By Jeffrey P. Carstens

INTRODUCTION Thermally induced fracture of rock is one of the oldest rock breakage techniques known to man. Primitive underground miners used fires to heat and crack rocks as early as the third century B.C. (Ref. 1). History aside, however, present-day tunneling and mining interests are reconsidering the use of modern heating units for rock fracture for some very good reasons. One of the most important advantages of many heating techniques is the lack of direct contact between the heating device and the rock. This means a lower wear rate relative to mechanical cutters, and no large reactant force to be supplied by the tunneling machine. In addition to avoiding physical contact, some heating systems (e.g., electron-beam guns and lasers) can deliver energy to a rock face much more intensely than can be conveniently handled mechanically. Thus, heating power densities of the order of lob to 107 watts/in.2 and greater can be achieved with high-power lasers. These high power levels allow much higher instantaneous penetration rates than can be achieved by mechanical cutting. Another advantage that accrues to some thermal techniques, such as, for example, surface spalling, is that the thermal fracture process works particularly well in certain rock types (e.g., granite) that are particularly hard to cut mechanically. Other methods, involving high power density, are able to cut any rock type, and are relatively

Jan 1, 1997

By Klaus Beckmann

Gentlemen : My object reads "Longwall Rapid Advance of Coal Mining in the Federal Republic of Germany". It is true that the percentage of coal obtained in your country from longwall faces, with at present 1.2, is still rather low, but it increased considerably since 1966 with 0.4 %. The coal mines of the Federal Republic of Germany ever used longwall as the classical method of coal getting. All attempts to introduce bord and pillar mining did not lead to any wider application of this method. The principal reasons, for this appear to have been: - the deeper depth of our workings, - the wish to keep working losses as low as possible and to utilize the deposits opened up by deep and therefore expensive shafts to the furthest possible degree, - the dense sequence of seams and the mutual influencing of the working points, - the high number of disturbances in the geologically much stressed deposits, - and the necessary considerations to the protection of the densely built-upon surface.

Jan 1, 1970

By H. W. Hintze

Coal handling facilities, such as utility plants, coal terminals, ports, manufacturing, processing, etc. Protect themselves against interruptions in coal receipts by maintaining a 60 to 90 day supply in storage. Not too long ago, these storage piles were referred in terms of hundreds or thousands of tons. Today, it is not unusual to have hundreds of thousands or millions of tons in storage. Burn, or shipping and receiving, rates have increased dramatically and storage piles have grown in horizontal as well as vertical dimensions. Fixed systems for delivering and retrieving coal from storage have increased in length and operating capacity and have become highly sophisticated in their operation. With few exceptions, mobile material handling equipment is used to handle all coal beyond the reach of these systems. These machines take excess loose coal from the fixed system to the storage area, place it on the storage pile, compact it, maintain the pile, protect against spontaneous combustion, the spread of fires if they occur, and return the coal to the reclaim system as required, plus many of the small chores around the facility.

Jan 1, 1981

By Robert Sturk, Knut O. Halvorsen

"INTRODUCTION AND BACKGROUND The world needs visionary people to break new ground and bring development forward. The human race has an inherent power and lust to explore and push borders, but also to connect and bring people together. Transport of people and goods has through history been a key factor to develop societies and increase collaboration between people and regions. Today, in the era of globalization, efficient transport systems are still vital for further development. Often, ideas of bold projects, like long bridges or tunnels, have been raised long before those projects are realized and actually built. This shows that visions must gradually be transformed into feasible business cases and sustainable political solutions. In some cases also technological development is necessary to make visions come true. Isambard Kingdom Brunel, indeed a visionary engineer, completed the oldest underwater tunnel in the world when the Thames Tunnel in London was opened in 1843. This tunnel is still in operation and now part of London’s rail transport system. Another milestone for the tunnelling industry was passed when the 54 km long Seikan tunnel in Japan was opened in 1988 after more than 15 years of construction. This tunnel is presently the world’s longest railway tunnel. Together with the 50.5 km long Channel tunnel between the UK and France, which has the longest undersea portion 37.9 km, they constitute examples of pioneering engineering projects that bring the industry forward. In 2016, the Gotthard Base Tunnel will be opened and then becomes the longest railway tunnel in the world with its 57.1 km. The trend is obvious that tunnels throughout the world are getting longer and longer. The Brenner Basis Tunnel presently under construction will yet again break the record being 64 km long. Presently, a number of even longer tunnels are planned and under design, some of these also have very long subsea portions, e.g. Bohai Straight Tunnel (123 km), Irish Sea Tunnel (around 100 km) and the Helsinki – Tallin fixed link (approximately 90 km). Northern Europe sees an increasing demand on efficient transport corridors to meet the growth of freight transportation between the Scandinavian Peninsula and central-Eastern Europe. Sustainable solutions will be required, and a shift from road/maritime transports to rail is imperative. Consequently, this paper describes yet another visionary project, a fixed railway link between Sweden and Germany, the Shortcut, to enhance traffic between these regions and to make it greener. It is true that this project still requires some work from politicians, economists and engineers to be realized, however, building a 100 km long tunnel under the Baltic Sea may become reality sooner than we think."

Jan 1, 2016

By W. C. Shanks

The Pioche District of Lincoln County in southeastern Nevada (Figures 1 and 2) has been an historically important producer of silver, zinc, and lead. Economic geology of districts in the Pioche area is summarized most adequately in recent reports by Tschanz and Pampeyan (1) and Gemmill (2) and only a few major aspects will be discussed here. Production in the Pioche District began in 1869 and early mining concentrated on silver-bearing fissures in lower Cambrian quartzites. In the early 1870's the Pioche District was second only to the Comstock Lode in world silver production (3). More recent mining activities have centered on the other major ore type in the area, bedded replacement of lower Cambrian carbonates by Ag-Zn-Pb sulfide ore. Production of replacement ore peaked around 1950. The present study is focused on the Pan American Mine because it is an excellent example of low grade carbonate replacement deposits, because there is little structural dismemberment, and because access was readily available. Most previous workers have suggested that both the fissure vein deposits and the bedded replacement deposits of the Pioche districts are a result of spatially related Laramide igneous activity. The purpose of this study is to determine whether ore genesis is a result of igneous activity or if mineralization might be related to late diagenetic processes such as formed Mississippi Valley "type" deposits. Stable isotopes of sulfur, carbon, and oxygen in ore and gangue minerals have been studied to determine the probable isotopic composition of the ore fluid and paleomagnetic studies of the carbonate rocks have been utilized to determine timing of mineralization. Additionally, petrographic and field studies of carbonate lithologies were undertaken in an attempt to delineate non-structural controls on ore localization. These studies are still proceeding and the results presented herein are, therefore, preliminary in nature.

Jan 1, 1979

By William M. Phillips

This paper will concern the processing of kaolin clays from the sedimentary deposits of Georgia and South Carolina, While the major processing steps will be touched on briefly, emphasis will be given to the dewatering of the clay-water slurries (slips) formed in the processing of kaolin clays The dewatering steps discussed will include gravity settling, centrifugal dewatering, vacuum filtration, and thermal dryings Of these dewatering steps particular attention will be given to vacuum filtration and the variables affecting filtration of these kaolin clays.

Jan 1, 1962

By Francois E. Heuze

This paper summarizes the geomechanics programs conducted in two hard rock underground mining operations in the Western United States, between 1966 and 1981. The two projects were directed towards understanding the behavior of the rock masses, at the scale of the caverns. To this end, the emphasis was put on large scale field measurements, complemented by limited laboratory testing. The results of these observations were used to build realistic finite element models of the underground chambers. In the marble mine, at Crestmore, California, the models were applied to the structural optimization of the room-and-pillar pattern. In the granite mining, at Climax, Nevada Test Site, the models explained some unusual stress changes observed during excavation. Based on the large number of geomechanical techniques employed, specific conclusions and recommendations are offered regarding the quality, applicability, and usefulness of the various methods. The two case histories clearly indicate chat numerical models are extremely useful for a detailed understanding of the structural behavior of mine openings. To be realistic, these models must be based first and foremost on large scale field observations. The lessons Learned on these two projects also are directly applicable to the design and analysis of nuclear waste repositories in hard rocks such as basalt, granite, and welded tuff.

Jan 1, 1982

By Walenty Frydel

The paper deals with highly efficient dust collecting systems of the 10-600 type which constitute new generation installations de- signed to eliminate dust hazard in headings driven with roadheaders. A vortex ventube controlling the air flow in the com- bined ventilation system by means of air vortex generated by the ventube drive unit is also presented. From the results of measurements of under-roof concentrations of methane it appears that the application of the vortex ventube makes it possible to decrease the under-roof accumulation of methane more than 10 times.

Jan 1, 1997

By James Diekmann

The Disputes Potential Index (DPI) is a computer program designed to help team mem¬bers assess the likelihood of contract disputes on a construction project. The program's predictions are based on data from 159 construction projects that encompass a variety of public and private projects. The impact of three categories of project characteristics are included in the DPI program, specifically, people, process and project characteristics. Ultimately, DPI returns an overall project score that indicates the likelihood of exces¬sive contract disputes. The output of a DPI analysis can be used as part of a contract readiness review or to define the need for extraordinary dispute avoidance procedures. This paper examines the development of DPI and presents the results of DPI analyses on several tunneling projects.

Jan 1, 1995

By John S. Cummings

In this paper the phrase "exploration for blind metal deposits" refers to exploration activities geared to the discovery of metal deposits which cannot be located by visual surface inspection. The word "system" refers to all of the components (people, money, corporations, techniques, etc.) which collectively result in an exploration process. The details of the system or systems which I have employed in exploration will not be discussed because of client relationships. However, some of the more severe problems in exploration result from how the system's components interact and our attitudes as to what exploration data is telling us, if anything. It is these items which will be discussed. Exploration for blind metal deposits, which has been relatively intense over the last 2S years compared to rather minor outlays prior to World War II has often been an uncoordinated assortment of various specialists employing various techniques (see Dickerson -1). In a program geared to the location of blind deposits, the lack of outcropping deposits or occurrences should not be a deterrent to a well conceived and well planned program. The severe cyclical swings in exploration activity, although often coinciding with depressed metal prices, by and large result from the failure of exploration operators to present a coherent and realistic program to management. It is my opinion that the stream of complaints criticizing management for cyclical exploration support are mostly unwarranted, as many of the programs and goals are ill defined. Although depressed market conditions may serve as the catalyst for exploration cuts, the underlying cause is that when the "chips are down", the non-directional, non-specific nature of many programs is revealed. Thus management should not be castigated for eliminating such programs during bad times, but rather they should be castigated for supporting them during boom periods.

Jan 1, 1978

Mineral processing plant operators are faced with the necessity to choose between many different possibilities for plant improvement. Only a few such possibilities, however, can be tested on the industrial site. Steady-state simulators make it possible to assess the effects of several different flowsheet modifications in a few days, thus helping the process engineer to make his choice implement the solution that seems the most appropriate and check it. The example described here is the crushing and grinding circuit of the Shila Gold Mine, jointly owned by CEDIMIN SA and BUENAVENTURA SA, in Peru. Several possible modifications for the purpose of increasing capacity have been simulated and the results assessed in terms of technical quality, investment costs and energy consumption. The best solution indicated by the USIM PAC simulator was implemented and gave a 20% increase in capacity with a pay-back time of two months.

Jan 1, 1993

By Jung-Joo Kim, Jong-Uk Kim, Turab H. Jafri, Han-Kyu Yoo

"INTRODUCTION Steel sets such as H-type and lattice girders are often installed in the tunnels before the hardening of shotcrete to ensure the stability of conventional tunnels in soft ground conditions. In practice, while designing the tunnels with the help of numerical analysis, steel sets are generally considered only as temporary support elements. Only a few studies propose the direct application of composite support in the tunnel design, based on large-scale experiments and numerical analysis. In order to assess the structural performance of the composite support consisting of shotcrete and steel sets, large-scale experiments were performed on two types of arch-shaped specimens by applying the combined effects of axial forces and bending moments. Based on the experimental results, numerical analysis was performed to assess the application of composite support in tunnel design. The crown settlement, axial forces, bending moments, and load distribution in the composite support were analyzed in the light of different structural patterns. LARGE-SCALE EXPERIMENTS USING COMPOSITE SUPPORT Preparation and Procedure of the Experiments The preparation setup as well as the organized procedure of the large-scale experiments using composite support is shown in Figure 1. An appropriate geometry of the specimens was selected by considering the standard cross-section of a two-lane highway tunnel in South Korea. Under the loading conditions meant to develop the axial forces and bending moments simultaneously, arch-shaped specimens were assembled with the ends of the specimens subtending a 60° arc angle at the center of the arc circle as shown in Figure 2. The fabrication of six specimens was completed in two groups based on the dimensions of steel sets, with the first group of three specimens being reinforced by H100 (No.1, No.2, No.3) and the other three by H125 (No.4, No.5, No.6). In order to reduce the voids on the boundary of the shotcrete and steel sets, concrete was casted over the steel sets instead of using shotcrete. The specimens were designed to incorporate the uniaxial compressive strength of 21 MPa. Shear keys and steel plates were installed at the ends of the specimens, so that shear failure could be avoided at the ends and the specimens could also be protected from detachment at the fixation. Translational and rotational movements at the ends of specimens were fixed."

Jan 1, 2016

By B. A. Hancock

New permit discharge standards instituted at Hecla Limited?s Lucky Friday Mine required installation of water treatment plants to manage water quality at two outfalls to the South Fork of the Coeur d?Alene River. The 002 Outfall Water Treatment Plant (WTP) is a clarification-filtration plant for treating the combined mill and underground discharge water flows. Process optimization efforts were a significant challenge until the negative impact the exploration diamond drilling products had on the clarification process was identified and resolved. The products were being wasted directly to the mine water discharge system which was pumped to the surface WTP. Anionic soluble oil and polyacrylamide based products were causing TSS particle hydrophobicity and dispersion that greatly affected coagulation and flocculation response, resulting in excessive chemical usage and treatment control issues. This paper details how problems associated with the drill products negatively impacted the 002 WTP and how system changes, alternative product usage and treatment at the source resulted in more consistent plant performance.

Jan 1, 2011

By Wayne A. Van Voast

Many coal beds that will be mined in southeastern Montana are aquifers that provide essential local water supplies. Mine cuts along aquifer outcrops create almost imperceptible piezometric changes. Monitoring near such operations at Colstrip has detected almost no water-level declines in observation wells. Mine cuts between outcrops induce rapid storage depletion and associated piezometric depressions. One such cut near Decker induced 1,250 m3/day of flow from storage and created a piezometric depression of 3 meters or more as far as 1,500 meters from the mine. No wells have yet become non-productive but losses of some are inevitable as operations expand. Alternative supplies are available from aquifers stratigraphically below the disturbed materials. Effluents from active mines are chemically similar to other area waters because they are mixtures or ground waters entering the mine cuts. Occasional high concentrations of nitrate do occur, however, as residuals from explosives. Spoils generally consist of confined aquifers of wasted coal and coarse rubble at their bases, overlain by finer-grained sand, silt, and clay. Hydraulic conductivities and storage coefficients are comparable with those of undisturbed confined aquifers. Water quality in mined lands is highly diverse because of diverse spoils lithologies and poorly-established ground-water circulation. Ground water in spoils is more mineralized than in the coal beds and chemically resembles waters from sandstone aquifers. Hydrologic effects of mining will not be catastrophic or widespread but may have local significance. Most notable changes will be in water quality; availability will not be permanently reduced.

Jan 1, 1978

By D. Malhotra

The number of variables which can effect flotation of molybdenite is very large. This paper discusses the effect of two operating variables, namely, the degree of aeration and agitation, on the grade and recovery of molybdenite. A series of factorially designed flotation tests were carried out in a "Leeds Automatic Laboratory Flotation Cell." The analysis of flotation results indicate that molybdenite can be characterized into fast-floating and slow-floating components. The rates of fast-floating components, which do not create a problem in flotation, could be varied by changing agitation of airflow rates. However, the rate of slow-floating components was stable and was only a function of residence time in the float machine. The degree of aeration has a significant effect on the grade of MoS2 with only a slight effect on the recovery of MoS2. The degree of agitation has a slight effect on the grade, but does not effect the recovery of molybdenite. The implications of the results on the design of flotation cells and control and optimization of the existing circuits is subsequently discussed.

Jan 1, 1977

By E. P. Lunghofer

Silicon Carbide and Aluminum Oxide were two of the early forms of man-made abrasives often referred to as synthetic and were invented at the turn of the century. Edward G. Acheson invented Silicon Carbide in 1893 and Charles F. Jacobs filed a patent for the manufacture of fused alumina from bauxite in 1900. Jacobs' patent provided a method for tempering the alumina by reduction and fusion to a degree of hardness and toughness suitable for abrasive purposes. These two inventions are the basis of the synthetic abrasive industry today. Improvements have been made in the equipment used in the process, however the process itself remains basically the same. In 1904 A. C. Higgins observed that hot spots developed on the shell of the pot furnace used in the reduction of bauxite. He found that by spraying water on the hot spots they could be prevented and, in addition, they failed to return in the same place. Higgins reasoned that the cooling effect of the water caused the melt contacting the metal shell to freeze as an insulating autogenous refractory. This suggested that an improved furnace design could be obtained by using a metal shell which is continuously flooded with water on the exterior surface. Paradoxically, a furnace required to contain tons of molten Aluminun Oxide was thus constructed of nothing but a sheet steel shell with no refractory lining at all. A test of such an arrangement was tried by Higgins with considerable trepidation and was found to be extremely satisfactory.

Jan 1, 1985

By R. D. Williams

In spite of the increasingly polarized and politicized view of climate science and climate change in the United States, many of the principles behind the ?theory? of Anthropogenic Global Warming (AGW) or Global Climate Change (GCC) are in fact firmly established both in fundamental physics and detailed observations and are widely accepted elsewhere. The discovery of the earth?s ?greenhouse effect? dates back nearly 200 years to the work of French mathematician and physicist Joseph Fourier in 1824 and 1827. In 1872, John Tyndall an English physicist and mountaineer, described the capacity of various gasses to absorb radiant heat. He identified water vapor and carbon dioxide as the principal ?greenhouse? gasses. The work of Fourier and Tyndall was the foundation for the theory that increasing carbon dioxide (CO2) in the atmosphere might be responsible for an increase in global temperatures developed by the brilliant Swedish chemist Svante August Arrhenius in 1896. This was backed up by the additional work of Gilbert Callendar in the 1930s, and Gilbert Plass, Hans Suess and Roger Revelle in the 1950s. There is little scientific dispute about the physics by which this occurs: carbon dioxide in the atmosphere absorbs long wave radiation that would otherwise escape into space, thus warming the lower atmosphere and respective temperatures worldwide. The Intergovernmental Panel on Climate Change (IPCC), approximately 2500 climate scientists from around the world, has concluded that increases in carbon dioxide resulting principally from the burning of fossil fuels are responsible for most of the continuing increases in global temperatures (IPCC, 2007). NASA?s Goddard Institute for Space Studies (GISS) states; ?The ten warmest years all occur within the 12-year period 1997-2008? (GISS, 2009). 2009 was the second warmest year on record and 2010 was tied with 2005 for the warmest year on record (GISS, 2010, 2011). The science is in fact settled; the earth has not cooled since 1998 as some have claimed. It continues to warm as evidenced by not only surface temperature records but also ocean temperature records as well as changes in physical and biological systems (IPCC, 2007).

Feb 27, 2013

By M. J. Shulman

An algorithm used by the US Coast Guard to find lost objects is utilized to optimally allocate exploration efforts during initial stages of an exploration program. Based on classical search theory, the algorithm assumes a target probability distribution function, a detection func¬tion, and a cost function. The three Junctions are analogous to delineating areas of possible mineralization, choice of exploration methods, and exploration budget. Application of the algorithm is shown for a hypothetical target distribution. Using the maximum number of field days available as the cost function, the optimal allocation of effort is shown for different exploration methods, e.g. electromagnetic survey and induced polarization. The adaption of the algorithm for the exploration process is discussed.

Jan 3, 1984

By A. W. Laughlin

Laser-Induced Breakdown Spectroscopy or LIBS can be used to provide exploration companies with precise and accurate chemical analyses in the field, in real-time, resulting in major time and cost savings. Using a Field-Portable Analyzer (FPA), anomalies can be followed up immediately while crews are still in the field. Lower limits of detection (LLDs) are element dependent, but many are sufficiently low to be useful in exploration. LLDs in ppm for selected elements of interest are: Be-2, Cu-3, Zn-20, As-200, Sb-500, Pb-30, Ag4, Mo-100, B-33, Ti-500, V-350, and Cr-1. LIBS analyses require little or no sample preparation.

Jan 1, 1999