Search Documents

By Ihsan Berk Tulu, Gaobo Zhao, Deniz Tuncay, Syd S. Peng

Longwall mine instrumentation for measuring abutment stress distribution, mining induced immediate roof stress change and deformation, and primary/secondary support loads and deformations provides critical guidance for the design of gateroad chain pillars and roof support. Field measurement results are also recognized as the best way to calibrate numerical models that have been used to study the failure and support mechanisms. International Conference on Ground Control in Mining (ICGCM) started in 1981 and since then, there were 26 papers published in the proceedings discussing the stress and load measurements as the face advanced using various field instrumentation techniques. The focus of this paper is on summarizing the analyses of the data published in these papers. Stress/load change monitoring included the following categories: gateroad chain pillar, abutment pressure, bolt load, and pre-driven recovery room. The data shows that the magnitude of stress changes as the face advances varies considerably from panel to panel and mine to mine. However, regardless of types of stress changes, pillar stress, abutment pressure, and bolt load, there exists a rough trend of stress increase as the face advances, generally consisting of three stages, i.e., stress/load (1) initially increases steady or slowly, (2) increases rapidly, and (3) increases reaching the peaks and dropping down slowly or sharply. The stress/load increases start earlier during the second panel mining and are larger than the first panel mining. This review makes it easy for the interested persons to find valuable data for other similar projects.

By T. R. Ellis

Many appraisers/valuers believe that the only valuation method available within the Cost Approach category for Real Property appraisal is the depreciated replacement cost method. Some valuation and financial reporting standards setters also believe the same. This paper introduces the minerals appraiser to a number of useful methods for mineral property appraisal that are based primarily on the principle of contribution to value, the predominant economic principle in the cost approach. Most of these cost approach methods discussed are primarily for use in valuation of exploration tracts and resource properties that have no defined reserves. However, the powerful rural cost method can be used to calculate the contribution of categories of resources, reserves, and other property components to the value of a mineral property. This method can be applied to mineral properties at all stages of development, including producing properties.

Jan 1, 2011

By M. R. Lastra

Island Copper Mine began gold recovery Tom molybdenum sulfide concentrates in April, 1985. Plant design capacity is 20 tons of molybdenum concentrate per day. The molybdenum concentrate is produced in a conventional copper/molybdenum flotation circuit by selective copper depression. After thickening, the molybdenum concentrate is leached with cyanide solution in a series of five leaching tanks. The leached concentrate is then filtered and soluble gold values recovered on activated carbon with a six column adsorption circuit. The gold leach extraction is approximately 80 percent with a gold adsorption on activated carbon of 97 percent.

Jan 1, 1986

By F. G. Crack, R. V. Ramani, R. L. Frantz

Management for mine construction and development differs from that needed for routine mine production and maintenance. An integrated approach to managing mine development projects must consider contract documents; management organization of a project; the project manager's role and the field supervisor's responsibility; and the use of scientific techniques for planning, scheduling, executing, and controlling projects. Professional project management encompasses the following: • Preparing contract documents that establish technical and financial schedules, and detail the responsibility for the physical work commitment. • Developing a project's organizational structure, to clearly define the roles of the project manager and the field supervisors. • Establishing project management and field supervisor relationships, to avoid ambiguity in assigning responsibility and to ensure desired project progress. • Using management science techniques, particularly networking techniques such as the critical path method for planning scheduling, executing, and controlling projects. Project Versus Production Management Project management differs from routine production management in the following ways: • Uniqueness: A project is unique. Production operations tend to be repetitive. The magnitude of one-time capital expenditures for many facets of mine development warrant special skills and attention. These professional project development skills must already be available by prior experience in the management team. • Personnel: In projects, personnel are usually assigned on a specialty basis and frequently change with the project activity. On the other hand, production personnel work together, more or less permanently. • Management Structure: In a project there may be several staff-line relationships that are not clearly defined and change with changing project activities. In a production situation, the lines of communication and authority are usually well defined. • Time Frame: A difference between project and routine production management is that project activities have comparatively less well defined durations and often tend to be relatively short-term. Production usually has both long-term and short-term plans and well defined long-term and shor-term goals. In project management, formal, critical, short-term reviews are frequently required. In production management, five year plans can be formally adjusted quarterly and annually. Short-term weekly or daily reviews can be informal. • Response to Delays: Delays in a development project may occur without anyone being immediately aware of their existence or suspecting the magnitude of consequence. In contrast, any delays in the production process can be easily identified from prior results comparison. Additionally, the response is quick, usually in a set routine. This can be traced back to the management structure and personnel. • Control Techniques: Measurements of project progress for control are not easily made due to the variety of activities that are carried on at the same time by different work groups. The yard-sticks of performance measurement for individual activities, let alone for the total project, are not easily established. However, due to the difficulty in detecting project delays, a workable control system is vitally important to a project manager. To apply a scientific project control technique such as "management by exception" requires specific planning and monitoring from the project manager for each activity in the project. Production and productivity are quick and effective yard-sticks of measuring performance in a routine operation. Control techniques required in production management usually revolve around these measures. Construction Contracts The construction contract is an important document that establishes contract scope, technical and financial details of the work, and achievement deadlines. It may also serve as the contract document to pay for work done and to verify field progress with planned progress. In practice, it is a good idea to develop a job-specific contract. This whole area is replete with legal precedence and procedures, and it is not the intent here to deal with the intricacies of establishing a contract document. But it is necessary to have an understanding of major contract types. Construction contracts are extremely important legal documents. They may vary in work specifications and enforcement of the provisions. Due to their nature, they must be composed with legal help and will take some time to compile. Even with all the precautions and provisions, it is not uncommon to find owner and contractor disagreeing. Therefore, it is important to include a way to resolve any difference quickly and to incorporate aspects of the contract as part of an overall management control tool for efficient project management.

Jan 7, 1982

By J. C. Yingling

[New stochastic process models are developed to calculate the probability of various fill levels in section feeders as a function of vehicle interarrival times, payloads and feeder-discharge rates. These models may be utilized to establish the minimum feeder-discharge rate necessary to prevent a feeder, with a particular surge storage capacity, from constraining the section's production rate. In addition, it is shown how the output from these models may also be utilized to calculate the probability of various flow rates at junctions in the conveyor haulage network, enabling one to size gathering belts. The model provides a basis for optimizing, (in economic terms) capacity specifications for feeders and conveyor belts in the materials-handling system by considering tradeoffs in the size of the two types of units.]

Jan 1, 1997

By R. Hagemeyer

In North America, the paper industry is by far the largest consumer of coating and filler mineral pigments. Present use is at an annual rate of 5.5 million metric tons with a value of $660 million. Current estimates are 65 percent is used in coating and 35 percent in filler applications. During the past decade, the switch to alkaline papermaking has provided the opportunity to substantially increase filler levels while maintaining paper strength. As a result filler consumption has been growing at a late in excess of 15 percent yearly. Unfortunately, within a few years, mandated recycling could slow or even reverse this trend. The critical issue is finding an economically viable method for recycling the mineral pigment and/or minimizing the disposal problem

Jan 1, 1994

By Allan M. Johnson

Since 1974 researchers at Michigan Technological University have been studying mine subsidence in the Iron River District of Northern Michigan. The district, which was active from 1881-1978, has had numerous cases of subsidence. Much of the subsidence resulted from rock mass failure but some appeared to have developed primarily in the thick glacial overburden which is a typical feature of this area. This latter observation led to the recognition that some of the surface subsidence was due to piping; i .e., loss of overburden material to the mine voids by groundwater flow (Johnson and Frantti, 1978). The Sherwood Mine was the last mine to operate in the district. With its closedown scheduled for late summer of 1978, a unique opportunity to monitor the mine as it flooded was presented. It was reasoned that with the cessation of pumping, groundwater would rise in the overburden and the mine would flood. The physical characteristics of the mine were favorable for piping to occur as the mine flooded. With the permission of Inland Steel Mining Company and the support of the U. S. Bureau of Mines, a project to monitor the Sherwood Mine for piping subsidence began in June of 1978. This paper present aspects of this study pertinent to the piping-induced subsidence events which occurred at the Sherwood Mine in 1980 and 1981, including acoustic emission monitoring of the subsidence activity, hydrologic monitoring of the groundwater regime and the flooding mine, laboratory modeling of the piping mechanism, and analytic procedures which are under development.

Jan 1, 1982

By R. L. Virta

Common clay is a natural, fine-grained material composed of hydrous aluminum silicates. Shale is a laminated sedimentary rock that is formed by the consolidation of clay, mud or silt. Production About 160 companies produced common clay and shale in 41 states. In states not reporting production, common clay and shale probably was mined and sold for construction applications by companies not participating in the U.S. Geological Survey’s canvass of producers.

Jan 1, 2005

By James E. Lawver

During 1981 the Florida phosphate industry produced more than 43 million metric tons of phosphate rock - about one-third of the entire world production and also generated nearly an equal amount of waste clay and waste clay-sized product that requires dewatering and disposal. The material balance of solids and water for a typical Florida phosphate mining operation is shown in Figure 1. Historically, the industry has impounded clay waste (about 60% below ground and 40% above ground) in earthen dams, often as large as 800 acres and occasionally greater than 60 ft. high. The dams have served the triple purpose of: 1. Dewatering initial 3% solid waste clay for process water re-use. 2. A reservoir system to minimize water discharge from the mining area and to capture and store rainwater thus minimizing deep well pumping requirements. 3. The ultimate densification and storage of waste clay.

Jan 1, 1983

By R. T. Dec

A review is undertaken of existing mathematical models of compaction process in roll press. The example of plane-strain, plane-stress model is presented together with comparisons between computed and experimentally recorded pressure distribution in roll nip region. Next, the discrepancies between predicted and measured values are discussed and practical method based on experimental optimization of compaction process using laboratory roll press is proposed. Examples of the selection of optimum roll press operating parameters for calcium oxide fines, sodium chloride and iron oxide dust are presented to illustrate advantages of the method. Finally scale up procedure is discussed for estimating the performance of commercial size roll press based on the data collected on laboratory size equipment.

Jan 1, 2000

By R. L. Virta

Four companies mined ball clay in four States during2004. They were H.C. Spinks Clay (owned by Franklin Minerals) Kentucky-Tennessee Clay (owned by Imerys),Old Hickory Clay and Unimin. Production was estimated to be 1.46 Mt (1.61 million st) valued at about $56.9 million, based on a preliminary survey of the ball clay industry. In 2003, production was 1.31 Mt (1.44 million st) valued at $56.2 million. Tennessee was the leading producer state with 61 percent of production. It was followed by Texas, Kentucky and Mississippi.

Jan 1, 2005

By Paavo Eerola

In May of 1984, it was decided that Outokumpu Oy would design and build a new nickel flotation mill to process ore from the newly discovered Enonkoski mine in eastern Finland. Since there hart peen a number of successful process charges in the existing mills, the design effort included the study and incorporation of several new developments, including all-autogenous grinding, "flash flotation", lane cell roughing, large cell cleaning and a computer-based, profit optimizing, process control system. The paper discusses the background and results of those studies, and a description of the resulting mill which will begin production in 1986.

Jan 1, 1985

By Lauren W. Choate

Wollastonite, a calcium metasilicate, derives its name from the man who discovered the mineral, Doctor William H. Wollaston, an English scientist. OCCURENCE Occurences of the mineral have been noted in Finland, Switzerland, Russia, Japan, Mexico and in the United States in Texas, California, Arizona, and New York. The only commercial deposit now being exploited is at Willsboro, New York. It is mined and processed by the Cabot Corporation whose home offices are in Boston, Massachusetts.

Jan 1, 1964

By W. Kracht

Frothers are surfactants used in floatation to aid generation of small bubbles. Studying events at the moment of bubble creation is a challenge because of the short time frame. This presentation introduces a novel acoustic approach. The technique has the resolution capable of detecting events that occur within 1-2 ms. The transition from coalescence to non-coalescence is tracked as a function of surfactant concentration and gas rate through the capillary. Results are given for some common flotation frothers and n-alcohols (C4-C8). A stress model is used to give a qualitative explanation to the observed action of frothers on coalescence prevention. Results for salt (sodium chloride) are included for comparison).

Jan 1, 2009

By J. Kuti

In room and pillar mining a large number of working points are arranged to follow a mining pattern. Geological and roof control problems can be overcome or their effect minimized by varying this pattern. Longwall mining on the other hand, fixes the mining pattern for anyone panel. This aspect of longwall mining leads to constancy, so that a well-conceived organization, ventilation, dust and roof control systems lead to daily repetition and subsequent simplicity of control. All the same, a fixed mining pattern calls for a very careful consideration and selection of design parameters. (Ref. 1.)

Jan 1, 1971

By Earl G. Hoover, V. S. Znamensky

For most geologists and miners the term asbestos refers to a group of highly fibrous silicate minerals that readily separate into long, thin, strong fibers of sufficient flexibility to be woven; these fibers are heat resistant and chemically inert, and possess a high electric insulation and therefore are suitable for uses where incombustible, nonconductive or chemically resistant material is required. The US Mining Safety and Health Administration (MSHA) specifically refers to the naturally occurring minerals chrysotile, amosite, crocidolite, termolite asbestos, anthophyllite asbestos, and actinolite asbestos as asbestos if the individual crystal fragments have the following dimensions: length-greater than 5 µm; maximum diameter-less than 5 µm; and a length to diameter ratio of 3 or greater. Since asbestos has been identified as one of the ten most carcinogenic substances (a cancer-causing agent), it has become, for many government regulatory agencies, a major issue concerning banning emissions to the environment. Very few recent issues have caused as much concern for the crushed stone industry as asbestos. Complicating the problem is the fact that several federal and state bureaus have greatly compounded the confusion because each has become involved in the asbestos dilemma. Simple solutions to a very complex problem have been proposed by these various governmental groups. In addition to governmental bungling is the fact that public interest groups have been able to use federal and state laws that have been enacted with a strong environmental bias to foment even greater complexities. Such is now the state of the asbestos problem. No con- firmed health risk has been associated with low-level exposure, namely crushed stone in an unbound form; a methodology for sampling and analyzing for asbestos has not been developed; a precise definition of what is asbestos does not exist, nor does a concensus among the various government groups as to what course of action to pursue. Pure asbestos as it is mined for commercial purposes does not exist in the properties mined by the crushed stone industry. Where the six asbestiform minerals do appear (to date we've been referring mainly to chrysotile in serpentinite formations in Maryland) the amount of the asbestiform mineral present is generally quite small. They generally appear in scattered, miniscule amounts. In the case of Rockville Crushed Stone in Montgomery county, Mary- land, the chrysotile is less than 1/2 of 1% of the rock deposit. No health risk has been identified with such minute quantities of asbestos minerals. MSHA standards for the occupational health and safety of quarry workers are being met; and there is every indication that normal background levels of asbestos, throughout the surrounding countryside, are as high or higher than levels measured on roads where the rock is used in pavement or base. The problem and the controversy lie with improper terminology on the part of so-called public interest environmental groups, aided and abetted by some governmental agencies who, to be charitable, we can best describe as uninformed. The news media frequently has fanned the issue, unintentionally we'd like to think, by quoting these misinformed authorities and not bothering to question the facts or adequately report balancing information handed to them. It is much better copy to talk about an asbestos cancer scare, than to deal with rather mundane measurements and descriptions that are hard to understand. At the heart of the issue is the improper use of the word asbestos. Instead of being confined to the geological description of the six asbestiform minerals-chrysotile, amosite, crocidolite, termolite asbestos, anthophyllite asbestos, and actinolite asbestos-the word asbestos is also wrongly used, but too-frequently to identify many other minerals that happen to have elon-

Jan 1, 1986

By A. A. El-Midany, R. M. Farag, A. M. Salem, S. E. El-Mofty

Bentonite represents one of the main players in the stability of the drilling mud. Its particle size and particle size distribution affect the physical properties of the drilling mud especially the rheological properties. Therefore, a specific particle size distribution was recommended by American Petroleum Institute (API) for use in drilling mud. To clarify the effect of individual size and size distribution, in this study, the bentonite sample was classified into different size fractions. Each size fraction was tested separately in terms of controlling properties such as filtration loss, plastic viscosity, gel strength, cake thickness, and packing density. The effect of each size fraction on the rheological properties of the suspension was correlated to the behavior of the whole particle size distribution in the bentonite sample. The results indicate that the coarser the particles, the higher the rheological properties; in this case, the API mixture is the highest. The filtration loss and cake thickness for the API mixture are lower than that of the individual size fractions due to its wider size distribution due to the filling of voids between larger particles with smaller ones, which lead to bed compaction and consequently lower fluid loss and cake thickness.

By M. Soderstrom

In a solvent extraction (SX) plant, stage efficiency calculations are used to determine mixer efficiency. With modern extractants and mixing equipment, it is generally taken for granted that stage efficiencies will be above 95%, but this is not always the case. Dependant on mixer/solution conditions, stage efficiencies can occasionally be low, therefore leading to higher reagent usage. Proper methods to identify when stage efficiency performance is below expectations, and ways to identify if it is an equipment or chemical issue are valuable tools for a plant metallurgist. With these tools and skills an on-site metallurgist can more quickly return their SX plant to proper operation. This paper will discuss methods for analyzing stage efficiency, evaluating factors that may affect stage efficiency, and evaluating the impact of stage efficiency on the overall operation.

Jan 1, 2010

By Langtry E. Lynd

Ilmenite concentrates prepared from beach and dune sands of Florida, India, Australia, and other localities deviate to varying degrees from the theoretical composition of pure ilmenite, and generally contain more Ti02 than the formula FeTiO3 would indicate, and some Fe203. This variation in composition is due to different amounts of altered ilmenite in the concentrates.(l) The alteration has been shown to take place by oxidation and leaching of the iron in ilmenite, to yield residual products consisting of amorphous or very finely crystalline titanium dioxide and ferric oxide, Other studies (2) have stressed that ilmenite may alter first to an amorphous titanium-iron oxide, or to an amorphous mixture of titanium and iron oxides, with later alteration to crystalline titanium dioxide. There has been some speculation as to whether alteration of ilmenite is usually caused by weathering or by hydrothermal processes,(3, 4, 5) Three main methods of approach were used to study the mechanism and rate of ilmenite weathering, (1) Etch tests were used to learn the relationship between crystallographic orientation and the rate of chemical attack on ilmenite. (2) Altered ilmenites in New Jersey sands were compared with ilmenite in rocks of the area from which the sands were probably derived, (3) Experiments were carried out to determine at what rate, and by what agents, originally fresh ilmenite could be altered in the laboratory under simulated weathering conditions.

Jan 1, 1959

By James Carroll, Lance Heyer

This paper describes the shaft design and construction for a 72-inch microtunnel under 14 active railroad tracks in Avondale, Louisiana. Initial shaft design for a deeper tunnel alignment considered secant piles with a jet grout plug. Final design for a shallower tunnel alignment included contractor input with support consisting of braced sheet piles with a jet grout plug. The authors further elaborate on jet grout implementation in very soft organic clay soils and the practical limitations of jet grouting. This paper emphasizes how all project participants worked together to utilize value engineering and alternative delivery on a unique tunneling project with a focus on temporary shaft support.

Jun 23, 2024