Search Documents

By K. C. Vories

Surface mining and reclamation has the potential to at least temporarily increase surface runoff and resultant erosion and gully development. This increase in erosion is due in part to compaction of the soil surface with heavy equipment, creation of large relatively unvegetated watersheds, and elimination of natural dendritic ephemeral drainage patterns. Methods for stabilizing gully channels which may develop prior to establishment of sufficient vegetation to control erosion are analyzed. Utilization of various sizes of riprap for channel lining, the use of riprap check dams, reinforcement of riprap check dams, and the relation- ship of type of control structure to area of watershed and resultant flow velocities are discussed.

Jan 1, 1986

By W. B. Greer

The performance of seals in boreholes, shafts, and tunnels is an important concern in mine safety, in the control of effluents from operating and abandoned mines, and in the underground containment of hazardous wastes (Einarson and Abel, 1990; Mining Waste Study, 1988). Despite the clear need for effective seals, few documented test results are available concerning the performance of in-situ seals. Some evidence indicates that horizontal or near-horizontal holes are especially difficult to seal properly (Kelsall and others, 1982). This research involved the installation, extensive hydraulic testing, removal, and post-test examination of a l0-cm-long by 10-cm-diameter cement grout seal in a near-horizontal borehole in limestone. The work was performed in an underground mine on Marble peak in the Santa Catalina Mountains, Arizona. A test hole was diamond cored in the re-crystallized limestone of the Escabrosa formation. The hole is 33.24 m long, 10 cm in diameter, and dips at 10.4 degrees. The hole extends between two drifts and thus is accessible from both ends.

Jan 1, 1992

By David L. Veith

As the basis for the State of Minnesota's Regional Copper-Nickel Study environmental evaluation, hypothetical mine models were developed ranging in ore capacity from 5.35 to 20.00 x 106 mtpy. Open pit and underground mining operations were defined utilizing conventional methods of ore extraction. Processing of the copper-nickel sulfide material involved conventional bulk flotation of the valuable minerals, with maximum water recycle And tailing disposal. Flash smelting and electrolytic refining of the concentrate resulted in 0.10 x 106 mtpy copper plus nickel metal, plus associated cobalt and precious metals. Variations in model parameters allowed environmental trade-offs to be identified.

Jan 1, 1980

By R. J. Sweigard, R. V. Ramani

G.F. Learning The paper by R.V. Ramani and R.J. Sweigard is a wonderful description of the labyrinthine web that has been spun about the mining industry by energetic bureaucrats and politicians over the past 50 years. The remedy for the problem, however, is not more of the same, but less. That may be difficult for the industry to achieve, for it is not a technical solution but a political one. And the current fervor for more detailed planning at all levels of government and private enterprise has become deeply ingrained. The authors recommend the provision of more information about mining and mineral resources to "macro" (i.e., government) land use planners. They apparently overlook, however, the already strong tendency on the part of most government land use planners to consider themselves omniscient. Thus, giving them more information about the technical problems of mining will only make them want to get more and more involved in the "micro" (private, site specific) mine development and production plans of the individual mining firm. In fact, this has already happened at all levels of jurisdiction from municipal to federal government. Examples are legion. The most effective way to ameliorate the adverse impacts of government land use planning on existing and potential mining operations is to: (1) introduce greater flexibility in the definition of land use zones by local and state governments; (2) adopt realistic and relevant ambient environmental performance standards in governing relationships between mineral land uses and concurrent or subsequent nonmining land uses; (3) allow greater leeway for economic considerations in land use decisions in contrast to the explicit legalistic approach now in vogue; (4) recognize that all minerals are not the same and that sand and gravel mining should not be treated the same as underground metal mining, coal stripping, oil field production, or in situ leaching; and (5) eliminate the notion that mining operators should be responsible for determining in detail the use of land by subsequent owners of mined land. This last bit of conventional ethic really makes no more sense than requiring the builders of every shopping center or government office complex to provide detailed plans for the use of that land when its use for shopping or government is ended. Did the builder of Ebbetts Field plan for Brooklyn after the Dodgers went to Los Angeles? Should the developer of the Bingham Pit plan for suburban Salt Lake City after the copper mining goes to Chile? The nation's mining industry must address these questions before further bankrupting itself to provide more data to planners and spending thousands of dollars per acre to create land that when reclaimed is worth only a few hundred dollars per acre. Reply by R.V. Ramani and R.J. Sweigard We thank Mr. Leaming for his valuable contribution. His views on the problems of land use planning and mineral resources are most welcome additions to our paper. As the title indicates, our paper was more concerned with the impacts of land use planning on mineral resource conservation than with the details of the planning process. On the whole, his five recommendations would be helpful for mineral resource conservation. However, we would suggest that the argument he presents for his final recommendation does not address the differences between mining as a land use and commercial or institutional uses. We believe that this difference is the crux of the issue. We share Mr. Leaming's desire to ameliorate the adverse impacts of land use planning. Possibly the most detrimental impact is the loss of mineral resources. Any development, whether mineral or community, that does not give proper consideration to other resources can result in permanent loss or sterilization of resources. With proper planning, some of these losses can be avoided. As our paper indicated, one factor that limits the consideration of mineral resources, and ultimately leads to their sterilization, is the generally inadequate levels of resource characterization and understanding of the unique nature of mineral resources and mining operations. The last point raised by Mr. Leaming is also important. In terms of reclamation and land use planning in mining districts, we certainly do not advocate spending more than what the results are worth. The main thrust of the paper was to explore the avenues for conserving the mineral resources so that, at some appropriate time, the issue of mining and reclamation can still be addressed.

Jan 4, 1985

By M. F. Martin

Dewatering aids are chemicals which enhance the efficiency of mechanical dewatering equipment such as vacuum disc filters and centrifugal dryers. A new dewatering aid has been developed which significantly lowers the moisture content of the mineral concentrate and causes none of the undesirable side effects normally associated with dewatering aids. Highlights of product development from laboratory screening through field testing will be discussed.

Jan 1, 1985

By Charles H. Grant

Communications in whatever we do, is one of the major problems we encounter. In an effort to provide a better understanding of the use of explosives, I am going to take a little different view of what explosives are, and how you might look at them as tools to fragment rock, and some of the problems encountered in doing so. First, let's take the explosive, and although there are many factors involved, I want you to consider these as being reduced to only two--shock strain imparted to the rock by the high early development of energy; and the other, the gas effect which is a combination of heat, moles of gas formed, rate of formation of these gases which develop pressures, etc..

Jan 1, 1968

By ERIK C. WESTMAN, JESSICA M. WEMPEN, DALLAN J. COONS, WILLIAM G. PARISEAU, MICHAEL K. MCCARTER

Safe, efficient underground mining is dependent upon proper pillar sizing. Pillar sizing is typically based on a combination of observation of prior behavior, point measurements, theory and numerical modeling. The actual stress redistribution within a pillar, while assumed for many years, has rarely been imaged. Such imaging can help confirm whether or not theoretical and numerical modeling methods agree with actual conditions within a pillar. This research presents a case study from a longwall mine in the western United States. A two-entry, gate-road yield pillar in the headgate of the mine was instrumented with seismometers and convergence monitoring stations, and was monitored over a period of about six months as the longwall face approached the pillar. In this paper, the stress distribution imaged using seismic tomography is compared to the stress distribution expected from theoretical models, geotechnical measurements and numerical models. The tomography results generally agree with those proposed by theory, convergence measurements and numerical modeling results. The agreement of the methods provides validation for the theorized stress redistribution, and this study provides further evidence that tomography can indicate the redistribution of induced stress within a mined rockmass and is another tool available to ensure that mining is conducted safely and efficiently.

Aug 1, 2022

By George C. Carter

It was just a little over three years ago that the "Go" button was pushed to start operations on the blending piles at Oro Grande. As is usual with any new installation, there were problems that had to be solved. This paper will concern itself with those problems directly related to quality control. To obtain a consistent outgoing quality level at the most economical level for a finished product requires two main points: 1. Measurement of variations in the process, 2. A method of making a predictable change to adjust for variations. The manufacture of cement requires a relatively high degree of accuracy if a consistent outgoing quality level is to be maintained. The blending piles were our solution to this problem.

Jan 1, 1962

By George Watson, Gu Quanzhong, S. Gerard Sawyer

Bulkheads, also known as hydraulic seals, are used to seal abandoned workings and protect adjacent active mines from explosion and control unwanted inflows of water from poorly sealed shafts, water-bearing strata, and abandoned mine areas or gobs (1). At coal seam outcrops, bulkheads have typically been used to prevent access and to control acid mine drainage. Bulkheads have also been installed at outcrop openings located within the footprint of an embankment dam, or within the reservoir of an impoundment, to prevent stored water or slurry waste from flowing into active or inactive underground mine workings (2). Components of MICON Bulkhead Seal MICON bulkhead seals in mining applications refer to seals designed to impound liquids or slurry. The MICON bulkhead seal is comprised of two concrete block walls set in the front and back and a polyurethane/aggregate core (Figure 1). The two walls are usually dry-stacked, surface-bonded walls constructed with solid load-bearing concrete blocks (ASTM C90) or concrete building brick (ASTM C55). The surface bonding material used in the wall construction must be MSHA-approved. The type of stone, if any, used to fill the space between the walls is not essential. However, MICON generally uses No. 57 limestone in 50 lb. bags, specified to moisture control, shrink-wrapped and palletized. The polyurethane foam used in the construction of the bulkhead seal is engineering specified and formulated by density based on the optimization of cost, seal core thickness, required adhesive strength, the use of stone filler and other required physical properties.

Jan 1, 2005

By I. G. Bowen

The pumping of abrasive and sometimes corrosive slurries is normally carried out at modest heads (say 100 ft) with specially designed centrifugal pumps. When heads become higher than this, two or more pumps are used in series but ultimately the system requires staffed pumps with consequent increase of costs. The only other type of pump suitable for high heads is the Ram pump but this is notoriously subject to wear. The paper describes a novel application of the so-called "lock hopper" principle to continuous pumping of slurries. The pump itself is never in contact with the abrasive slurry nor is it subject to head or capacity limitation. It works by displacing slurry with the clear fluid component of the slurry (in most cases water) through cylindrical vessels fitted with plug valves to control the discharge and filling operations. Two such vessels are used and the scheme is completed with a liquid clarifier which allows the pipe flow to be maintained continuously. The paper describes experience on the prototype unit used to discharge tailings from a coal washery in Scotland. A tentative evaluation is also made of the economics of this pump against conventional equipment.

Jan 1, 1965

By Jack E. Brockway

As tunnel boring machine technology has expanded, so has its range of application. Tunneling machines (TBM's) are tackling tasks today that fifteen years ago were considered "inappropriate". A case in point is incline/decline TBM boring. An incline or decline bore presents peculiar design considerations that differentiate it from a horizontal bore. This paper reviews those design considerations as they apply to TBM's, backup, muck handling and other tunneling subsystems. In addition, several abbreviated case studies are presented. By the review of real life tunneling techniques as well as design considerations, the "appropriateness" of TBM incline/ decline boring today becomes apparent. INCLINE Introduction In contemplating the impact of incline versus horizontal tunnel boring system design, the obvious consideration is gravity. Up-hill boring can be quite different than horizontal boring. Muck, water and machine weight all tend to slide down the incline. In addition, hydraulic and lubrication systems if unaltered, will find their fluids pooled in the lower corners contentedly ignoring such higher elevation items as gears and bearings. In order to address this inherent gravity problem, a review of

Jan 1, 1983

By Jess H. Albino, Girish Roy, James M. Monsees

Construction of the North Hollywood line of the Los Angeles Metro System required crossing the Hollywood Fault as the twin transit tunnels extend into the San Fernando Valley. The Hollywood Fault is considered active and represents the largest active fault that the North Hollywood Redline extension will cross. The feature is a thrust fault with the north plate overriding the southern plate and creating the Santa Monica Mountains in the process. South of the fault lies the alluvial valley and Hollywood. North of the fault are the Santa Monica Mountains which rise locally to more than 1200 feet. The average overburden at the seismic section is about 300feet and is overlain by Runyon Canyon Park, a municipal park with environmentally sensitive areas. The actual fault plane was anticipated to lie within the southernmost120 feet of the 600 to 700-foot-wide fault zone. The special seismic section constructed for the tunnels consisted of an enlarged cross-section with special lining, drainage and finish features that will facilitate the restoration of metro service in case of a major event occurring on the Hollywood Fault. The discussion will address the geology, the procedure used to define the design event and predicted displacements, the unique design features as well as the construction methods used and the instrumentation and the results obtained.

Jan 1, 1999

The criteria used to design, operate and control flotation columns are significantly different from those used for conventional flotation machines. Therefore, a computer-aided design (CAD) package for column flotation has been developed. The simulator has been set up using guidelines developed at Virginia Tech and information published in literature during the past few years. The simulator is useful for determining the proper design and appropriate operating conditions for a column cell to fit a specific set of conditions. In addition, the simulator can be used for training in column operation and for trouble-shooting operational problems. Simulation results have been found to be in good agreement with experimental data obtained using laboratory columns.

Jan 1, 1990

The need for an integrated approach to optimization of unit operations in both the pit and the mill has long been recognized, but the complexity and nature of the overall problem has up to now resisted solution. This paper reports on a modeling methodology which couples symbolic and numeric computing to unify operations in both the pit and mill. The ultimate goal of this work is to optimize all operations that are influenced by blasting. Blasting plays a key role in all facets of operations. Obviously, drilling and blasting costs are determined by blast design, but the down-stream costs that are closely related to blasting results are often treated as separate functions: loading, hauling, cleanup, and crushing and grinding are all heavily influenced. Diggablilty and bucket fill factor are a function of fragmentation, the condition of the floor and uniformity in the shape of the muck pile. Likewise, cycle times and loading delays partially determine haul cycles, while fragmentation distribution and size determines the efficiency of truck loading. Removal and breakage of oversize causes loading delays and increases cleanup costs. The influence of blasting doesn't stop at the crusher. Mill productivity, power consumption, and maintenance are a function of the feed. Even at the SAG mill a reduction of a critical particle size during blasting can increase throughput. Thus, a bottle-neck for production far removed from unit operations in the pit can be alleviated by a modification in blast design. The question is: how do we optimize blasting with respect not only to itself but to al\ related mining and milling operations? For that matter, how do we even model blasting so that we can control the results of a blast?

Jan 1, 1991

By Ronald W. May

The Lower Cretaceous McMurray Formation in northern Alberta contains bituminous sands interbedded with other sediments which form the reject encountered during mining operations. Grade prediction is based on a combination of geological interpretation, computer modelling and past mining experience. In addition to estimates for ore, an accurate estimate of "waste" or "reject," are required for Mine Planning. This study investigates the ability of point-kriging using geostatistics, to augment the existing data base of drill-holes in a study area on Syncrude's leases. This approach enables the assessment of potential "worst" case - "best" case scenarios within the context of Mine Planning.

Jan 1, 1985

By J. R. Weber, R. D. Haddenham, J. H. Bailey

Introduction The Vernal Phosphate Operation is located in northeastern Utah, about 18 km (11 miles) north of Vernal, about 280 km (175 miles) east of Salt Lake City, UT. The plant began initial operations in 1961 under the name of the San Francisco Chemical Co. In 1981, Chevron purchased the operation from Stauffer Chemical Co. In 1982, plant capacity was doubled to about 72.6 kt/a (800,000 stpy) of phosphate concentrate. From 1984 to May 1986, another expansion increased the capacity to 1.2 Mt/a (1.3 million stpy) of concentrate. It also incorporated a number of equipment and process changes designed to increase the overall plant phosphate recovery. A 150-km (94-mile) slurry pipeline, the world's longest phosphate pipeline, was also constructed from the Vernal plant to a new Chevron Chemical and Fertilizer plant near Rock Springs, WY. Over the past five years, plant expansions and the pipeline construction have been accomplished without missing a single concentrate shipment.

Jan 1, 1987

By David W. Lillie, Pier A. Abetti

This paper reports on a study of the impact of fast growing new technologies on the market for copper over the next 15 to 20 years. The greatest threat is clearly the inroads of fiber optics on the traditional market for copper in communication cable. Opportunity areas identified include heat pumps, solar power and heat, desalination, electric vehicles and others. The overall impact of new technologies on copper is expected to be modestly positive if adequately encouraged by effective R&D.

Jan 1, 1986

By K. L. Gabby

Selective removal of mercury from cyanide leaching solutions while retaining silver has been a long-standing problem, due to the chemical similarity of mercury and silver. In order to be practical, a mercury removal process needs to be both highly selective and use inexpensive materials. This paper reports the use of zinc sulfide (ZnS) as a precipitant for mercury. The mercury cyanide complex (Hg(CN)4 2-) undergoes a replacement reaction with the zinc sulfide, forming insoluble HgS, while the silver cyanide complex (Ag(CN)2 -) remains in solution. Under appropriate conditions, the separation of mercury from silver is nearly quantitative, with close to 100% removal of mercury, while nearly none of the silver is precipitated.

By M. L. Mellish

The year 1988 unexpectedly turned out to be a good year for the US coal industry. In fact, it was a third consecutive year of record coal production. Accord¬ing to preliminary Energy Information Administration data for 1988, domestic coal consumption went up 5%, or 41 Mt (45 million st), from 1987. Coal exports were up by a surprising 13.6 Mt (15 million st). In 1988, 22.7 Mt (25 million st) of coal were drawn from stockpiles for consumption. Even so, US coal production increased to 862 Mt (950 million st). That was up 28 Mt (31 million st) from 1987. While coal consumption, exports, and production were up, delivered prices for steam coal continued to slide during the year. Metallurgical coal prices, however, firmed up and showed a moderate increase. This reflected tight metallurgical coal markets at home and abroad. Coal consumption US coal consumption reached 800 Mt (882 million st), compared with 759 Mt (837 million st) in 1987. Increased metallurgical coal consumption was one factor. Most of the rise in coal consumption, however, was due to unexpectedly high electricity demand. Unseasonably hot summer weather al lowed added coal-fired electric generation to supplement the drought-related reduction in hydro-electric power supply. Electric utilities consumed 687 Mt (757 million st) of coal in 1988, 35.4 Mt (39 million st) more than in 1987. Coal-fired power plants remained the primary source of US electricity generation, providing 57% of the total in 1988. Coal consumption at coke plants increased 13%, to 38 Mt (42 million st), from the level consumed in 1987. This increase reflects the recent recovery in the iron and steel industry. Metallurgical coal consumption in 1988 could have been greater. But US coke plants reportedly reached their maximum practical production capacity. As a result, net US coke imports amounted to 1.45 Mt (1.6 million st). Despite increased industrial activities, steam coal consumption by industrial plants was up only slightly from the 1987 level, amounting to 69 Mt (76 million st) in 1988. Residential and commercial coal consumption remained virtually unchanged at 6.4 Mt (7 million st). Coal exports and imports US coal exports rebounded in 1988, reaching 86 Mt (95 million st). It was the highest level of annual US coal exports since 1982, when they reached 96 Mt (106 million st). An unusual set of factors led to an opening for US coal exporters in 1988: • a high level of industrial production in Japan and the European Economic Community, • supply disruptions due to labor problems at coal mines in Poland and Australia, • a drought-related reduction in hydro-electric power generation in Canada, requiring increased coal-fired generation, • China's problems in meeting its export commitments, and • a fall in the value of the US dollar. US metallurgical coal exports in 1988 amounted to 56 Mt (62 million st), 9.1 Mt (10 million st) more than the 1987 level. Europe, Japan, and Canada were the principal importers of US metallurgical coal in 1988. European countries, in particu¬lar, increased their take by one-third of US metallurgical coal. The labor problems in Poland and Australia contributed to these higher levels of imports. So did increases in pig iron production of 8% in Japan and 9% in the European Economic Community. US steam coal exports - including bituminous, anthracite, and lignite-increase to 30 Mt (33 million st). This was up from 25.4 Mt (28 million st) in 1987 Contributing to this overall rise were 1.8-Mt (2-million st) increase in shipments to Canada and a 2.7-Mt (3-million st) increase to Europe. Unaffected by the somewhat tighter world coal market, US coal imports showed a slight increase to 1.8 Mt (million st) in 1988. Colombia continue to be the leading exporter to the United States, followed by Canada and Venezuela. Venezuela's entry into the US market is a relatively recent one, having made its first significant shipment in the fourth quarter of 1987.

Jan 1, 1989

By L. Alagha, L. Sanchez-Calderon, M. Silwamba, W. Kirk

Selenium-rich metallurgical waste, also known commercially as “crude selenium,” is a byproduct of the copper (Cu) refining process. This by-product, contains ~ 90% selenium (Se), precious metals, platinum group metals (PGMs), and other critical elements. This study investigated the leaching efficiency of Se from the sludge under alkaline conditions using different oxidizing agents to enrich PGMs and precious metals in the leach solid residue. The effectiveness of each oxidizing agent during leaching was assessed and compared. Additionally, Eh-pH diagram for Se was established under specific experimental conditions and utilized to inform process optimization. Key variables, including leaching time, temperature, and oxidant concentration, were evaluated for their impact on the efficiency and the selectivity of the oxidative alkaline leaching process.

Feb 1, 2025