Search Documents

By R. Cooper, K. De Wet, A. Janwong

"Horsehead Metal Products is a zinc refinery in Mooresboro, NC, treating crude Waelz oxide (WOX) to produce special high-grade zinc by a hydrometallurgical process comprising leaching, zinc solvent extraction/electrowinning, melting and casting and bleed treatment. Cadmium removal by zinc-dust cementation plays an essential role in the bleed treatment circuit to prevent cadmium buildup in the circuit. Silica, though present at a low level of approximately 0.3 percent in the WOX feed material, had a significant impact on the efficiency of cadmium cementation with zinc dust, most likely due to the passivation of zinc dust particles with silica gel. Solid/liquid separation efficiency by filter press was also affected. To identify the source of the silica issues, silica levels were mapped throughout the circuit, and adjustments, including using pregnant leach solution as the feed to cementation, and pH control in the WOX leaching and neutralization were introduced to mitigate the issues created by silica gel in the circuit. IntroductionLocated in Mooresboro, NC, Horsehead Metal Products Inc. is a hydrometallurgical zinc refinery processing Waelz oxide (WOX) to produce special high-grade (SHG) zinc. The flowsheet, known as the Modified Zincex process, consists of leaching, solvent extraction (SX), electrowinning (EW), melting and casting and bleed treatment (Fig. 1). Cadmium cementation, part of the bleed treatment process, provides an essential bleed of cadmium from the circuit, as metallic cement. The cadmium cementation circuit consists of agitated cementation reactors, a zinc dust addition system, filter presses, agitated purification (releach) reactors and a cadmium concentrate filter press.At the refinery, WOX pulp is leached at a controlled pH to achieve the maximum zinc extraction, according to the main reaction:"

Jan 1, 2016

By Robert Hochscheid

A patent issued to J.N.J. Leeman (1957) described the change in performance that takes place when a cyclone is installed in the horizontal position rather than the vertical position. Although this patent was directed more toward improvements that could be realized in the heavy medium cleaning of coal, it contained specific references to reducing the quantity of fine solids that would report in the underflow, and an example for fine sand classification is also included. The three cyclone installations for which data is given in this paper demonstrate that horizontal mounting of large cyclones can improve classification efficiency, eliminate some operational difficulties, and reduce cyclone maintenance requirements in closed circuit grinding installations. Cyclone Experience at Serrana S.A. Each of four grinding circuits at the Serrana S.A. de Mineracao Apatite flotation plant in Brazil have a 2.7 X 4.6 meter (9 X 15 foot) rod mill and each originally operated in closed circuit with two vertically mounted Model D20B (500m nominal diameter) Krebs Cyclones. New feed size is 25mm. The Apatite is liberated at a relatively coarse 35 to 28 mesh grind, but the 500mm cyclones had to be fed at 66 pct. solids in order to obtain an overflow analyzing 12 pct. coarser than 42 mesh. Because dilution water in the cyclone feed had to be limited, classification was inefficient, and there were other significant circuit difficulties as summarized in a recent article by C. A. Busnardo (1984):

Jan 1, 1985

The rheological behavior of high concentrated coal -water slurry (cws), a new liquid fuel, is an important factor in the preparation, transportation and combustion. The conventional viscosimeters designed for Use with true fluids are not suitable to the measurement of the rheological behavior of cws. So that a special viscosimeter of tube type for cws was designed and set up in .laboratory. Experiments using two kinds of cws from two provinces from P. R. Olfna were conducted. It is found from test results that the experimental cws possess the rheological character of Bingham fluid and there is the existence of the wall effects which causes the measurement errors. In our former paper published the wall effects were discussed III the light of methods of Odroyd and Jastrzerbsiki to make the correction of the experimental results. But a number of tests are necessary to meet the need of determining the slip coefficient. In this paper the models of the wall slip velocity and the thickness of the slip layer of Bingham fluid were proposed III in theoretical approach which were satisfactorily used in the correction of the measured results of the rheological character of cws.

Jan 1, 1994

By G. R. Rao, K. A. Natarajan, P. Devasia

The role of growth conditions and adhesion of Thiobacillus ferrooxidans on the leaching of chalcopyrite was investigated. Thiobacillus ferrooxidans grown on sulfur, thiosulfate and ferrous ion substrates was used in this comparative study. Growth on sulfur, a solid substrate, requires bacterial adhesion unlike that required in the presence of soluble thiosulfate and ferrous ion in a mineral-salts medium. Solid substrate-grown cells showed higher rates of leaching than those grown in liquid media. An initial lag period noticed during leaching by solution-grown cells was absent when solid substrate-grown cells were used. Such a behavior is attributed to the presence of an inducible proteinaceous cell-surface appendage on the sulfur-grown cells. This appendage aids in bacterial adhesion onto the mineral surfaces. Such an appendage is absent in solution-grown cells, as substantiated by electrophoretic measurements. The importance of bacterial adhesion and the direct mechanism in leaching by Thiobacillus ferrooxidans are demonstrated.

Jan 1, 1997

By John W. Robertson, Edwin A. Zink, Gerald P. Zink, John E. Wolgamott

Equipment which will reliably produce high velocity water jets for use in rock excavation is now available. This report reviews some cases where water jets were used in excavating low to medium strength sandstone in Colorado and Utah. The primary discussion is of water jet assisted rotary drilling for blast and bolt holes in tunnels, shafts, and chambers. The subjects include drilling performance, effects on work environment, safety, and controlled blasting results. Information is also presented concerning trench excavation utilizing water jets.

Jan 1, 1983

By Paul D. Tomlingson

There are huge benefits for mining operations that have a well-defined maintenance program that is understood and followed across the total operation. But for operations lacking a quality maintenance program, there is equal assurance that nearly every major maintenance problem can be traced to this omission. Few problems will be permanently corrected until such a program is implemented. Definition The maintenance program re-quires the interaction of all mine departments. Initially, the production department will request work and the maintenance department will identify work, principally through preventive maintenance inspection and testing efforts. Maintenance will then classify the new work to determine the best way to respond. Maintenance will plan selected major jobs to enable its crews to carry them out more effectively. Maintenance will schedule the planned work with operations. Supervisors will assign all types of work to their crews then, control the work through effective supervision. As work is completed, maintenance will measure the work using an accurate information system. Next, it will assess overall accomplishments against goals such as performance standards or budgets. In addition, the pro-gram would prescribe a means to evaluate every aspect of the operation as it affects maintenance so that necessary improvements or changes can be identified, prioritized and acted on. Such evaluations should be part of a mine-wide continuous improvement effort. A well-defined maintenance program is one of the best investments a mining operation can make to assure its profitability. Educating the total operation on the pro-gram assures long-term dividends from the investment.

Jan 1, 2008

By C. A. Young, J. D. Miller

The surface chemistry of the calcite/oleate flotation system was examined by in-situ FT-NIR/IRS. Spectra of combination and overtone bands of aliphatic stretching vibrations revealed gauche/trans conformational changes that occurred solely as a function of temperature. The conformational changes were attributed to the simple "melting" behavior associated with phase transitions. It was concluded that chemisorbed oleate at calcite surfaces is gel-like at temperatures below 22oC, resembles a coagel between 22oC and 31oC, and becomes micelle-like at temperatures above 31oC. By comparison, chemisorbed oleate at fluorite surfaces also undergoes these phase transitions but is additionally dependent on adsorption density. The conformational changes were observed at high chemisorption densities (> 2.0x10-10 mol/cm2) and attributed to molecular forces, primarily van der Waal's interactive forces, among neighboring chemisorbed oleate molecules. Similar analysis of in-situ FT-NIR/IRS spectra of surface-precipitated calcium dioleate at calcite surfaces did not exhibit this behavior thereby confirming that surface-precipitated calcium dioleate remains in an all-trans conformation. The results help explain why surface polymerization is not observed at calcite surfaces but is observed at fluorite surfaces.

Jan 1, 2002

"Use of the Bond Work Index to size industrial grinding equipment was widely known. Bond also described its application for measuring grinding circuit efficiency. Bond Work Index efficiency has been widely used by industry, but until now without concise standard methods, or a formal guideline, for doing so. The Bond Efficiency Sub-Committee of the Industrial Comminution Efficiency work group of GMSG has produced such a guideline, which follows. It covers the methods and provides examples of how to calculate the Bond Work Index Efficiency of most industrial grinding circuits. Bond Work Index testing equipment and methods are also provided. The next steps are: (1) to establish standard reference testing materials and one or more laboratories to serve as bases for reference testing; (2) to establish the accuracy of relative circuit Work Index Efficiency determinations; and (3), to develop and provide a public data base of industrial comminution circuit Bond Work Index Efficiencies. OUTLINE Introduction and Background Part 1. Determining the Bond Efficiency of a Grinding Circuit Method Demonstration/Example Calculations Bond Work Index Testing Equipment and Procedures Accuracy of Comparative Circuit WI Efficiency Determinations (under development) List of Symbols Part 2. Data Base of Bond Grinding Circuit Efficiencies (under development) References Annexes: A1. The Bond Crushing WI Test Equipment and Procedure for Bond Efficiency Determinations (Revised March 26, 2015) B1. The Bond Rod Mill WI Test Equipment and Procedure (Revised March 26, 2015) C1. The Bond Ball Mill WI Test Equipment and Procedure (Revised March 26, 2015) Introduction and Background Please see the references and slide presentation “Bond Efficiency SLC (rev3)-print.pdf.” This efficiency determination applies to most brittle materials in their naturally occurring (un-scalped) size distributions being treated in size reduction circuits down to a product sizing of approximately eighty percent passing 70 µm (see below). Unusually shaped materials (e.g. mica) should be regarded with caution. Part 1. Determining the Bond Efficiency of a Grinding Circuit Method In the plant: • Define the circuit for which the WI efficiency is to be determined • Procure samples of the circuit feed and product • Obtain the power draw of the size reduction equipment at the drive pinion(s) • Obtain the circuit throughput rate (dry tonnage) In the laboratory:"

Jan 1, 2016

By T. Bajpayee, L. Prosser, A. Iannacchione

Reducing the number of roof fall injuries is a goal of the NIOSH mine safety research program. Central to this effort is the development of assessment techniques that will help to identify the nature of the risks associated with working under potentially hazardous roof conditions. This paper discusses a method to determine the roof fall risk using a qualitative risk analysis technique. The ability to determine roof fall risk has been a long-standing goal of safety professionals and can provide the kind of information, needed by on-site personnel responsible for worker safety, to mitigate roof fall injuries.

Jan 1, 2007

By Donald O. Rausch, William E. Hawkes, Odin Jr. Strandberg

INTRODUCTION Kennecott Copper Corp.'s Tintic Div. Burgin mine is a 725 t/d (800 stpd) lead-zinc producer, located in the east Tintic mining district, 5.6 km (3.5 miles) east of Eureka, and 130 km (80 miles) south of Salt Lake City, UT. The Burgin mining complex includes three shafts, shop, dry, and office facilities, and a 454 t/d (500 stpd) flotation concentrator. Production and ser¬vice entry to the mine is through a 4.26-m (14-ft) diam concrete-lined production shaft, and a three-compart¬ment rectangular shaft. A connection with the Apex No. 2 shaft and the Burgin mine provides a second exhaust airway. Bear Creek Mining Co., Kennecott's exploration sub¬sidiary, began exploration of the Burgin mine area in 1957 with the sinking of the 335 m (1100 ft) deep No. 1 shaft. A station was cut at the 320-m (1050-ft) level of the shaft and extensive drifting, diamond drilling, and some winzing and raising confirmed the presence of a major lead-zinc ore body, the main portion of which oc¬curred below a hot saline water table. Surface facilities and the 4.26-m (14-ft) diam concrete-lined production shaft were completed in 1966. Ore production has been steadily increased to 725 t/ d (800 stpd) since 1966. The collar elevation of the No. 2 production shaft is 1731 m (5678 ft) above sea level. The mine's three levels, the 1050, 1200, and 1300 are at elevations of 1414.6, 1356.4, and 1338.1 m (4587, 4450, and 4390 ft), respectively. The approximate elevation of the hot saline water table is 1382.6 m (4536 ft). The earliest production on the east Tintic mining district was from the Eureka Lilly mine in 1909. Later, in 1916, the Tintic Standard mine was discovered, and pro¬duced ores with a gross value of $80,000,000 through 1956. The Eureka Standard mine located 1.6 km (1 mile) southwest of the Burgin mine produced ore worth $12,000,000 from fissures in the Tintic quartzite along the Eureka Standard fault. Ores produced from the east Tintic mining district through 1971 are valued at $151.3 million. The production from the entire Tintic district is approximately $500 million. GEOLOGY The Burgin ore deposit occurs as replacement bodies in limestone, dolomite, and shale. Numerous fault struc¬tures and rock formations make the mine geology com¬plex. The mineralization is strongly associated with sev¬eral major geological features, which include the Ophir formation, consisting of limestone, dolomite, and shale as the favorable host rock, and the structural influence of the east Tintic thrust, the Eureka Standard and sev¬eral other significant faults. Fig. 1 depicts the Burgin 1300 level workings, a generalized configuration of the ore body, and the main geological features. Covering the quartzite, limestone, dolomite, and shale facies enclosing the Burgin ore deposit are 183 to 274 m (600 to 900 ft) of andesite. The Burgin ore consists of massive sulfide and oxide lead-zinc ores with significant silver and cadmium val¬ues. The main ore minerals are galena, cerrusite, and spalerite. Extensive manganese oxide deposits are associated with the lead-zinc ore occurrence. A limited

Jan 1, 1982

By S. Acar, P. Somasundaran

Results of selective flocculation of natural ores containing two or more minerals and of synthetic mineral mixtures do not usually agree with what is expected on the basis of the results from single mineral tests (Acar and Somasundaran, 1985). This is mainly due to the ionic species released by the minerals, which act differently under different pH values. The objective of this investigation was to study 1) the surface chemical composition of selected sulfide minerals-natural chalcopyrite and pentlandite and synthetic covellite, millerite, and pyrrhotite-and 2) the changes brought about by the dissolved mineral species. Electron Spectroscopy for Chemical Analysis (ESCA) was used to perform the surface analyses.

Jan 1, 1991

This paper was developed as part of an effort by the National Institute for Occupational Safety and Health (NIOSH) to identify risk factors associated with bumps in the prevention of fatalities and accidents in highly stressed, bump-prone ground conditions. Changes of failure mechanism with increasing confinement, from extensional- to shear-dominated failure, are widely observed in the rupture of intact specimens at the laboratory scale and in rock masses. In the previous analysis conducted in 2018, both unconfined and triaxial compressive tests were conducted to investigate the strength characteristics of some specimens of a Utah coal, including the spalling limits, the ratio of apparent unconfined compressive strength (AUCS) to unconfined compressive strength (UCS), the damage characteristics, and the post-yield dilatancy. These mechanical characteristics were found to be strongly anisotropic as a function of the orientation of the cleats relative to the loading direction.

Jan 7, 2020

By Prasad S. Mulukutla

INTRODUCTION The use of specialty chemicals In mining Is an Important consideration In determining the economic efficiency of a floatation plant. The plant metallurgist would like to maximize the recovery of valuable minerals while maintaining an acceptable grade product. The direct cost of the reagents, while significant, Is only a part of their economic effect. Reagents determine the flotation rates and the selectivity of the mineral separation. In flotation practice, mineral selectivity can be achieved through the addition of various reagents that can control the wettablllty of a particular mineral In the flotation pulp. The reagents which will generally optimize the flotation process are commonly classified Into three distinctive categories: collectors frothers and modifiers. Large tonnages of metal sulphide concentrates which are the source of most of the common base metals are produced economically by fairly standard flotation techniques. The advent of modern technology coupled with the necessity of processing finely disseminated and complex ores of low grade has Increased the need for utilization of non traditional and high selective chemicals reagents for the economic recovery of metals and raw materials. Mining operations in developing countries continue to progress at a rapid growth as many countries mine and process both metallic and nonmetallic ores. The total mine production of base metals, precious metals, Iron ores and coal In developing countries In Africa, Asia and South America has been much higher as compared to the western world production In terms of tonnage and dollar value. Global capital Investments In mining during 1991-95 Is $ 55.1 billion and It Is anticipated that the development of new and specialty reagents may be concentrated In the processing of aluminum , copper, precious metals and Industrial minerals with special reference to potash, phosphates, kaolin and silica sands.(1) The challenge for the design and development of new specialty chemicals Is dependent on Its cost performance and environmental acceptability. Information on the theory and application on the development of mining chemicals has been reviewed In several conference proceedlngs,(2-4) publications(5) and also discussed by several Individual authors.(1,6-10) These publications serve as a comprehensive reference source on the reagents used In several flotation processes. This paper discusses the present trend in the use of specialty mining chemicals In diversified mining operations on several mineral systems with particular reference to sulfide ore systems. The necessity to expose these specialty chemicals through aggressive marketing techniques In mining operations In many developing countries Is also presented. SPECIALTY CHEMICALS Specialty mining chemicals, like other specialty chemicals, share common business characteristics that transcend geographic boundaries. They are manufactured 1n a few selected areas, generally expensive relative to commodity chemicals, shipped and compete globally and usually require specialized knowledge for proper use. Specialty mining chemicals are relative newcomers to chemical markets. The vast majority of mining chemicals are derived from products that are less than two decades old. Traditional collectors and frothers have been available for a considerably longer time. The emphasis on adding value to existing products and byproducts Is responsible for several characteristic features of the mining chemicals business. Most raw materials for these chemicals are related to oil and gas byproducts, chemical refineries, pulp and paper mills and all chemical manufacturers. Until the last several years these operations were located In Industrialized countries, while a significant number of mining chemical users were In developing countries. Therefore International trade In mining chemicals developed through agencies or agents in each particular country.

Jan 1, 1993

Reaction kinetics for gold dissolution in acid thiourea solutions were investigated using formamidine disulfide as an oxidant. For the conditions studied it appears that a surface reaction limits the rate of gold dissolution. The rate was found to be first order with respect to thiourea concentration and half order with respect to the concentration of formamidine disulfide; the apparent activation energy for the reaction was 10.40 kcal/mol (43.40 kJ/mol); and the reaction rate was independent of pH for the pH range 1.0 to 3.0.

Jan 1, 1999

By Francis Martino

There are numerous techniques and predictive models used by geologists and mining engineers to define coal reserves and plan mines. The traditional reserve estimation methods commonly used include the isopach, triangular, polygonal, inverse-distance weighting, weighted-moving-average, and trend-surface methods. Geostatistically-based estimation techniques are now being examined by many geologists and mine planners as a superior alternative to these traditional methods. With today's coal mine development costs often exceeding $100 million, and power generation $1 billion, it is logical that a technique that can indicate the degree of confidence associated with a reserve estimate (fuel supply), and thus also the degree of risk, is highly desirable to the coal producer, the financiers, and those desiring to commit to coal utilization under short or long-term supply arrangements.

Jan 1, 1983

By Clement K. Chase

Since the dawn of cyanidation leaching techniques for precious metals, certain manganese-bearing silver ores have been a problem due to low silver extraction. Since simultaneous occurrence of silver and manganese is common in nature, this situation has made many otherwise attractive silver deposits uneconomic in the past. Several older techniques have been useful but at $1.29 per ounce of silver, the economics were unfavorable. With the new look in silver prices and some improvements in processing technology, neglected silver districts offer new promise.

Jan 1, 1981

By A. W. Popp

After forty years of exploration and development, the heavy mineral sand deposits of the Murray Basin are on the eve of substantial exploitation by Iluka Resources Limited, Southern Titanium NL and RZM/Cable/Bemax, whom plan to initiate mining and processing operations in 2005. A trial mining and processing operation was undertaken on the Wemen North strandline deposit in 2001-2003 by Murray Basin Titanium, a joint venture of Sons of Gwalia and RZM/Cable, which brought to light a number of mining and processing problems which have since been the subject of extensive studies and process development work. The mineralogy of these weathered strandline deposits is complex by industry standards due to the variety of the heavy minerals present, coatings on the mineral grains and the extensive weathering and alteration which has taken place during the past 50 million years. This paper provides an overview of the complex mineralogy that, in turn, dictates the processes that can be used to recover the valuable heavy minerals. The Murray Basin encompasses some 300,000 km2 and has been a depositional basin, often land locked, since the start of the Cenezoic Era. The economic heavy minerals include ilmenite, altered ilmenite, leucoxene of highly variable composition, rutile, and zircon. There are also other heavy minerals present such as cassiterite, chromite, and monazite in quantities that pose both problems and opportunities. The clay content and overburden thickness also play a major role in the selection of the deposits to be mined. Project Services Consultants (PSC) has undertaken the preparation of this paper as part of its ongoing participation in the mineral sands industry and in particular the project development activities in the Murray Basin region currently being undertaken by Iluka Resources. PSC has been involved with the mineral sands business for several years with senior staff having in excess of 30 years global industry experience. The company is well placed to provide a range of services to clients like Iluka Resources in the areas of project development, execution and strategic development and industry advice.

Jan 1, 2005

By L. Diels

About 45% of the contaminated sites are dealing with heavy metal problems. Metals are spread in the environment by mining activities, surface treatment and non ferrous processing. As heavy metals can not be degraded, removal or immobilization (leading to bioavailability reduction) are the only risk reducing measures that exist. The currently best available technique for remediation of heavy metal contaminated groundwater is to pump the contaminated water and to treat it in a wastewater treatment plant installed on the surface. Next to this often used, but expensive, pump and treat technologies, heavy metals can be immobilized by inducing sulfate reducing bacteria (SRB) to transform the sulfates, that are very often present in the same groundwater (due to the metal mining or processing activities), into sulfides. These sulfides will precipitate the metals as insoluble metal sulfides. At the moment several studies have demonstrated the feasibility of this In Situ Bioprecipitation Process (ISBP) for the removal of heavy metals from ground-water as well at lab scale (batch and column tests) as at field scale. However, some questions arise concerning the continuation of the process, the efficiency and the sustainability of the precipitates. The presented study will try to answer these questions. The study is based on more than 10 different studies, all done by the same authors, on different groundwaters and aquifer samples. The presentation will give an overview of the guidelines necessary for a correct and successful bioprecipitation process with stable metal sulfide precipitates. An important question in the ISBP is related to the sustainability of the heavy metal precipitates. It could be observed that the interruption in the carbon source delivery also stopped the in situ bioprecipitation process. Depending on the metal also some release from the precipitate could be observed. It was shown that release can occur with Co and Ni. Aquifers, on which the metals precipitated during the ISBP, were treated in a sequential extraction process under an-aerobic and aerobic conditions. It could be shown that especially under the anaerobic conditions the Zn and Cd precipitates changed from the leachable and the exchangeable fraction to the organic or Fe-Mn fraction (i.e. from the unstable to the stable fraction). The same could be observed for Co and Ni but still some fraction was present under a more available form. On the other hand it could be shown that large differences were observed concerning the heavy metal speciation on the aquifer in function of the used carbon source during the ISBP. The molasses treated systems showed a much more available heavy metal fraction on the aquifer compared to the lactate or HRC® treated groundwater. The different speciation forms based on the use of different carbon sources will be discussed in detail. It will pay attention to the influence of the carbon source, the efficiency of the induction of the bioprecipitation process, the influence on the competence between sulfate reducers and methanogenic bacteria and the influence of low pH on the ISBP. It seems that acetate, which is also a degradation product of fermentation of some carbon sources, can inhibit some sulfate reducers. Also the relation between slow release compounds and immediately available compounds will be explained. Finally a pilot study will be presented showing the problems that can be encountered during this process. Focus will be put on the induction of the process, the keeping on of the process and the follow up of the process by the installation of in situ mesocosm socks. These results will allow the correct implementation of the ISBP with an eye on longevity and sustainability of the process and present the ISBP as a much more sustainable alternative to the pump and treat technology as measure for heavy metals contaminated groundwaters.

Jan 1, 2006

By Enrique Jelvez, Pierre Nancel-Penard

The traditional way of generating open-pit mine production schedules has several limitations. This work addresses the design and production-scheduling problem by considering minimum operational space requirements under a Direct Block Scheduling approach to generate extraction sequences that satisfy the operational space required. For this, traditional formulations were extended by including a new set of constraints that generate operating spaces for mining equipment to move and extract material. Then, a heuristic algorithm produces close to optimal practical pushbacks. This proposal was applied in a case study, and the results show its ability to generate practical production schedules without sacrificing expected return, obtaining differences in terms of Net Present Value (NPV) lower than 1% when compared to the traditional approach.

Jun 25, 2023

By D. Buranek, J. G. Wulff, F. W. Gifford

I. INTRODUCTION During the past few years, the state of the art of disposal of solid and liquid waste products from uranium mining and milling operations has experienced some rather interesting and significant changes. Some of these changes have resulted from technological advances in the milling operations and in the engineering aspects of the actual design and construction of the disposal facilities. However, the most significant changes, at least those which have had the greatest impact on the comparative cost and economics of modern disposal systems, have been environmental requirements and regulatory controls, which have become increasingly stringent in recent years. Without delving into the details of the myriad of new laws and regulations which now control the uranium industry, it can be stated with reasonable confidence that one of the principal purposes of more rigid state and federal controls over this industry is the basic desire to promote safer, more reliable and longer term means of effectively controlling and disposing of the potentially objectionable waste products resulting from uranium mining and milling operations. It is difficult to take issue with these basic goals because their need was spawned by past lack of awareness and inattention on the parts of both government and industry to the long term environmental problems and potentially hazardous conditions which can be created by limited planning and ill-conceived or poorly controlled and executed disposal practices. On the other hand, despite the good intentions of those who developed and those who are administering the regulatory controls now in effect, the basic danger exists that overgeneralization of the approach to disposal problems and overrestriction of the potentially acceptable solutions for uranium mine and mill waste disposal could have a significant, adverse economic impact on the mining industry and the ultimate consumers of their products. The regulatory pendulum, which perhaps swung too far toward lack of controls over uranium mill waste disposal in the 1940's, could now well be headed too far in the opposite direction, that is toward over-regulation in the form of restrictions based on technically unrealistic or weakly supportable

Jan 1, 1980