Search Documents

By Chunlin He, Xinsheng Li, Feng Yang, Lu Han, Yuezhou Wei, Feng Gao

The solvent extraction of vanadium (V) from Na2CO3–NaHCO3 solution was attempted using Aliquat-336 (methyltrioctylammonium chloride) extractant dissolved in sulfonated kerosene as diluent with 2-octanol as phase modifier. The influence factors, such as Na2CO3 concentration, NaHCO3 concentration, temperature, extractant concentration and impurity P, on vanadiumextraction were investigated. The results revealed that the single stage extraction efficiency of vanadium reached above 89%from 20 g/L Na2CO3 – 20 g/L NaHCO3 solution under the following conditions: extractant concentration of 15%, room temperature of 20–30 °C, 2-octanol of 6%, phase ratio (O/A) of 1:1, and oscillation time of 1 min. The addition of NaHCO3 into Na2CO3 solution could lower the pH value of the Na2CO3 solution, improve extraction efficiency of vanadium, and not introduce other impurities. The phosphate anion did not interact with the vanadate anion in the Na2CO3–NaHCO3 solution. The P in the Na2CO3–NaHCO3 solution had little influence on vanadium extraction.

Jul 30, 2020

By I. Martinez-Dominguez

In September 1992, mining in Mexico was opened again to foreign investment by President Salinas-de Gortari, after thirty years of "Mexicanization" of mining industry which limited foreign participation up to a 49 % (or 34 % in case of national reserves) on a Mexican mining corporation. During said period mining in Mexico was controlled by four or five big mining companies and besides mining production was focused mainly on silver, lead, zinc, copper and fluorspar. Suddenly in middle of a big crisis on Mexican mining industry due to low prices of minerals in the world and also in a period on which it seems that mining industry in the United States and Canada has been condemned to die for environmental reasons, it appears a new Mexican Mining Law to permit foreigners to participate in mining in Mexico' trough Mexican mining corporations that they may control up to 100 %

Jan 1, 1994

By M. A. Oskouei

Draglines are the main energy consumers in strip mines. Given the growing cost of energy and environmental concerns, it is important to properly understand dragline energy efficiency. The goal of current research at Missouri University of Science & Technology is to account for operator practice and operating conditions in modeling dragline energy efficiency. This paper presents preliminary correlation analysis and a framework for stochastic modeling of dragline energy efficiency. Thirteen operating parameters (including cycle times, payload, swing angle, and height of dump pile), operator working schedules, operating conditions, and drag, hoist, and swing energies were monitored for an 85 yd3 dragline. Operator effects were examined by two-sample t-tests. The relation between the parameters and energy consumption were assessed by correlation analysis and a stochastic modeling framework has been proposed for dragline energy efficiency. The results show that operator effects are significant (p< 0.05) and energy efficiency is correlated with operating parameters. The completed model will help the coal mines better predict energy consumption, with uncertainty, for different operating conditions.

Feb 27, 2013

By Bruno Bussière, Guosheng Zhan, Michel Aubertin, Vincent Martin, Robert P. Chapuis

The study evaluates the hydrological behaviour of exposed and covered waste rock dumps. The objectives were to determine the major factors influencing unsaturated flow in waste rock dumps and covers, and to improve the in-situ, laboratory and numerical modeling characterization methods. Using material properties obtained from in-situ and laboratory tests, waste rock dumps of different configurations, with and without covers, were modeled. It was found that a properly designed “Store, divert and release” (SDR) cover allows most of the water to be diverted downslope and discharged outside of the waste rock dumps. The SDR cover seems to work efficiently even in extreme storm events. The numerical modeling results show that the unsaturated hydraulic properties (e.g. air entry value and water entry value) of the materials largely control the infiltration of water into waste rock dumps.

Jan 1, 2005

By David S. Bolin, Bruce Kennedy, Leigh A. Readdy, Graham Mathieson

INTRODUCTION The estimation of ore reserves is a process that begins with the earliest exploration stages on a property and continues throughout any subsequent evaluation and exploitation of the deposit. During exploration and preliminary evaluation, the results of these reserve estimates constitute the basic data for prefeasibility studies and economic analysis. The decision to continue exploration and development or to abandon a prospect is often based upon these studies. During the active life of a mine, reserve computations are continuously revised to assist in development planning, cost and efficiency analyses, quality control, and improvement of extraction and processing methods. Accurate reserve estimates are also required when financing a project, purchasing or selling a property, and for accounting purposes such as depletion and tax calculation. It is important to remember that the reliability of ore reserve estimates varies progressively through time as more and more information becomes available. The lowest order of reliability of estimation of reserves exists at the time of discovery. The maximum level of certainty concerning the ore reserves within a deposit is reached when the deposit is completely mined out. Between these two extremes are variable levels of certainty as to the tonnage and grade of the resource. This is particularly true of that portion of the mineral resource that constitutes the "minable reserve," as this portion is dependent upon economic as well as geological and technological factors. In the following discussion, several of the factors affecting ore reserve computation and some of the commonly used methods of calculation are presented. The first part of the discussion is confined to classical methods of hand calculation utilizing level maps and sections. The second part of the discussion presents an overview of somewhat more sophisticated methods of geostatistics which have been developed within recent Years. Geostatistical methods frequently provide the best ore re- serve estimates for many deposits. However, a digital computer is required for such geostatistically derived estimates due to the number and complexity of the cornputations involved. For many properties the classical nongeostatistical methods are adequate, particularly in the early exploration stages. In fact, it is the author&apos;s contention that even at those properties where the geostatistical approach is employed for reserve estimation, the geological and engineering staffs should prepare an estimate by traditional means. This provides an internal audit for the reserves and at the same time requires a continuing close appraisal of geologic problems that influence the presently known geostatistically estimated reserves and production at the mine.

Jan 1, 1982

By Miroslaw M. Hajdasinski

A project&apos;s rate of return (ROR) [The list of all the acronyms used in his text is provided at its end.], be it an internal or external one, usually needs to be approximated. The success and efficiency of an approximation procedure depend on the quality of the initiating parameters such as bounds or seed values (guesses). Current approximation procedures commonly use bounds and guesses dictated by intuition rather then by mathematical consideration. The paper presents three ROR-bounding and six ROR-guessing approaches and examines their suitability on the examples of the typical project cash flow patterns.

Jan 1, 1996

By A. Mull, J. Weyer, J. Brune

"The “Reiche Zeche” mine in Freiberg, Germany, a 600-year-old lead-zinc-silver mine with extensive open mine workings, experiences severe ventilation losses due to leakage. Much air leaks into abandoned workings, decreasing the airflow available to active working areas. Usually, this leakage occurs in remote areas that lack transportation infrastructure like roadways or rail, making it difficult to haul construction materials to the sites to erect passive ventilation controls such as stoppings, regulators and seals. Transportation distances make it impractical to hand carry traditional construction materials, such as bricks and concrete. Alternative materials, such as brattice, foaming polymers, concrete canvas, and some innovative ventilation control designs have been investigated for this purpose. The suitability of the materials investigated depends on many factors including the pressure it can withstand, the ease of transportation, and workability. Impacts of mine water must be considered, as the Reiche Zeche is below drainage and experiences significant inflow of water. Researchers must consider the effects water inundation as well as how the stopping construction material reacts to being exposed to acidic mine water. INTRODUCTION Problem Statement Mining in the area around Freiberg, Germany began in the 12th century. The mine is used for research, mining engineering education, tourism and air conditioning for a local hospital. The first records of mining in the Reiche Zeche are from around 1384. Due to the strength and competency of the host rock, many of the oldest workings still stand and remain open today, although they may not be accessible. Reiche Zeche also connects to several other, closed mines in the area that are largely unmapped. This allows air to leak into neighboring mines, reducing the air available to ventilate to the working areas of Reiche Zeche. In order to improve ventilation efficiency, it is necessary to control the ventilation and reduce leakage by constructing seals, stoppings and regulators. A challenge with building traditional seals and stoppings in the Reiche Zeche is that the old workings lack transportation pathways or rails. Also, the lack of compressed air, water or electricity makes it difficult to operate power tools and drills. This means that construction materials must be hand carried – some over distances of several kilometers. Figure 1 shows a typical drift in the Reiche Zeche. Researchers investigated using lighter, more easily transportable materials including concrete canvas, expanding polyurethane and polyurea foams, and brattice. The applicability and utility of these materials depends on a variety of factors including the ventilation air pressure, chemical resistance to acidic and mineral-laden mine waters, ease of transport, and ease of construction. Stoppings and seals must be substantially constructed so that they remain tight and do not require maintenance. It is also important to consider the toxicity of the construction materials in case of a mine fire."

Jan 1, 2016

By Janet E. Lamarre

Current statistics show that 90% of new-business failures are caused by the unsuitability of the entrepreneur for the business he has started. Are you a suitable candidate for success as a consulting geologist? Should you start your own geologic consulting business, and when? This paper investigates the demand for consultants with respect to general economic trends and mineral exploration activity trends. Furthermore, the study reveals certain technical skills and personal characteristics important to the success of the consulting geologist. Research shows chat certain expectations which prompted geologists to change careers are fulfilled while other unanticipated expectations often are also met.

Jan 1, 1985

By B. A. Slaker, T. Miller

"An underground limestone mine in eastern Ohio was experiencing significant floor heave and roof falls, attributed to high horizontal stresses. Areas of the mine showing floor heave were monitored with roof-to-floor extensometers and photogrammetry surveys, to determine the rate and magnitude of heave. Extensometer data were recorded hourly at four locations across adjacent entries while photogrammetry surveys of the floor were performed at the same locations every two to five weeks. A final survey was performed using an I-Site 8200 laser scanner. Following instrumentation, floor heave up to 10.1 cm (4 in) was measured by the extensometers, photogrammetric reconstructions, and laser scanner over a 6-month period. The extensometers were biased by the location where they were placed, failing to consistently capture the location and extent of floor heave and cracking. The photogrammetry surveys were not precise enough to capture small magnitude movements. Mining in the area was halted and within several months the floor movement and incidence of roof falls was significantly lessened. INTRODUCTION Limestone formations in the United States can be subject to relatively high horizontal stresses due to the presence of tectonic loading of the strata. Horizontal stresses have a documented history of causing stability issues in underground limestone mines. Kuhnhein and Ramer (2004) discussed the influence of horizontal stress on complex ground control interactions associated with limestone pillar design and mine layouts. Esterhuizen et al. (2008) documented roof damage observations associated with high horizontal stresses such has roof guttering, beam instability, oval-shaped falls, and failure propagations. There have also been a number of documented case histories of horizontal stress causing unexpected roof and pillar failures at shallow depths (Stacey and Yathavan, 2003). To the knowledge of the authors, there has only been one well-documented case of floor failure causing stability issues in an underground limestone mine. Murphy et al. (2015) documented the role that a weak, moisture-sensitive floor had in the development of a massive roof collapse. For this paper, the study site neighbored, and was in the same general geology of, the site in Murphy et al. (2015). However, the weak, moisture-sensitive floor was not present for the current study. The current study site has experienced significant floor instabilities caused by high horizontal stresses. The instability area was monitored using two different methods to determine if the floor failure would eventually propagate into roof or pillar failure. The objective of this paper is to analyze displacement monitoring measurements from string potentiometers and remote sensing techniques in an area experiencing active movement. Based on the measurement trends and observed damage from inside of the mine, the presumed failure process will be discussed."

Jan 1, 2017

By Sigmund J. Sulinski

The following is a progress report on a continuing study being made by the Sanitary District for purposes of developing reliable data for predicting costs and progress on future tunnel contracts. All data available to date on five separate tunnel contracts has been analyzed. All were machine-mined in soft ground, all used steel ribs and wood lagging and finished inside diameters varying from 5&apos;6" to 6&apos;6". Basic data regarding progress per shift, hours mined per shift, hours of downtime per shift, cause of downtime and type of soil mined were reported by the District&apos;s resident engineer at the job site. Figure 1, Weekly Mining Report is an example of the form used. Data regarding manpower and equipment used during tunnelling operations was also supplied by the resident engineer during the course of construction. Soil type being mined was verified by the resident engineer during construction, by visual observation, and compared with data listed on a previously prepared soil profile. The soil profile is a graphic presentation of anticipated soil stratas superimposed on a cross section

Jan 1, 1997

By K. A. Allison, D. R. Van Orden, R. J. Lee

Continuing analysis of environmental samples for asbestos content has resulted in the misidentification of non-asbestos amphibole particles as asbestos fibers. These errors have received wide publicity (such as in the asbestos-in-crayon story) and have caused unnecessary reformulation of products. The primary cause of these errors has been a poor understanding of mineralogy and analytical techniques among the many asbestos laboratories that arose following the passage of the AHERA regulations. Presented here is a procedure based on published data that can be used to correctly classify an elongated particle as asbestos or as non-asbestos.

Jan 1, 2005

By Justin Cardwell, Alyson Cartwright

"Grade estimation is the cornerstone of longrange mine planning. Pit designs, metal recovery, mining costs, reserves calculations and reporting are all dependent upon a reliable grade model. If the geology is poorly understood or the interpolation methods and parameters have been haphazardly constructed, then massive financial losses will be the inevitable outcome. Therefore, a properly trained geologist must use all of the appropriate tools available including deposit knowledge and advances in modeling technology to construct the most geostatistically and practically sound long-range block model.Certain deposits, such as the sedimenthosted deposits at Tenke-Fungurume, require an interpolation method that best suits the style of mineralization. In 2014, Hexagon Mining developed a tool in MineSight called dynamic unfolding (MSDU) that has the potential to improve upon previous Euclidean-based interpolation methods. MSDU utilizes the nonstationarity of a folded grade trend to more accurately construct variograms and improve interpolation results based upon a modeled three-dimensional surface.Geology overview. The sediment-hosted Tenke-Fungurume mining district is located in the southeastern part of the Democratic Republic of the Congo (Fig. 1). The rocks within the district are primarily dolomites and shales from the lower half of the Roan Supergroup that were mineralized by ascending pregnant copper and cobalt rich brines within a massive sedimentary basin (Cailteux et al., 2005) (Fig. 2). These oxidized brines likely found a fluid channel in the porous RSC unit. The surrounding rock units provided a redox boundary for copper and cobalt precipitation along organic rich beds, forming a massive stratabound deposit that was later broken up by several subsequent tectonic events (Dewaele et al., 2006)."

Jan 1, 2015

By J. C. Schneider, G. Van Weert

Hydrochem Developments Ltd. has developed and put into full scale operation a novel type of vertical flotation column incorporating a multiplicity of mechanically agitated stages. Characteristics of this flotation column include a low height to diameter ratio, high upgrading factors and the possibility of modifying geometry and operation to specific flotation requirements. A commercial unit is currently handling up to 100 tpd rougher concentrate at Dickenson Mines Limited, Balmertown, Ontario. Design parameters and plant performance will be discussed.

Jan 1, 1988

By K. Heasley, A. Yassien, A. Khair, S. Peng

There are three major components of a fully grouted roof bolt which primarily determine its ability to develop and sustain load: the steel rebar, the resin annulus, and the rock/grout interface. The untensioned, fully grouted roof bolt is subjected to loading only when the surrounding rock deforms. Vertical rock deformation is generally a result of strata sagging and bedding plane separation, whereas horizontal deformation is typically a result of bedding plane sliding. These two types of deformation create different types of internal loads with-in the roof bolt, tensile stress for vertical rock deformations and shear stress for horizontal rock deformations. Also, as a result of the mutual load transfer between the rock and bolt, shear stress will be developed along the grout/rock interface. According to the exact bolt loading conditions, different failure modes may occur: bolt axial failure, bolt shear failure, and shear failure along the grout/rock interface. Understanding these possible failure modes and their root causes is the key to eliminating roof failures in underground mines employing fully grouted resin bolts. Using ABAQUS 5.8, a finite element model was developed to simulate the components of the fully grouted bolt and its interaction with the surrounding roof strata. Several models were conducted to investigate how load transfer occurs between the rock and the bolt under different geological and mining conditions. The effects of bed-ding plane location and properties, and strata sequence on bolt stability were studied. Also, the effects of hole roughness on bolt stability were discussed. Bolt axial failure was not observed within the range of the studied parameters; however, a combination of high overburden depth, a bedding plane located at 2 to 3 ft from the roofline or a low coefficient of friction along the bedding plane caused strata sliding and shears failure in the bolt. Also, in the case of a weak immediate roof, the shear stress at the grout/rock interface could exceed its ultimate capacity lead to slippage.

Jan 1, 2004

By QUANWEN PU, Yonggang Wei, Bo Li

The spent catalyst is one of solid waste resources, which contains precious metals with considerable recovery value. However, due to the different compositions of catalyst, the recovery process is difficult. Most of the catalysts are supported by alumina which has good alkali-soluble properties, while platinum is insoluble in alkali. Platinum is enriched by pressurized alkaline solution which is a kind of hydrometallurgical process. The novelty of this study is the separation of alumina and platinum from the spent catalyst and the enrichment of platinum in the solid phase. In this study, a leaching process using NaOH as leaching agent under high temperature and pressure was employed. The effects of alkali concentration, leaching temperature, leaching time, and liquid–solid ratio on leaching efficiency were investigated. The optimum process conditions were determined as follows: alkali concentration of 240 g/L, temperature of 200℃, pressure of 1.20 MPa, time of 1 h, liquid–solid ratio of 5:1. It was concluded that the leaching rate of alumina can reach 99.69%. The content of platinum increased from 0.1749 to 21.12%, the loss of platinum was 3.39%, and the enrichment ratio of platinum increased by 120.82 times. The leaching kinetics of alumina was studied based on the shrinkage core model. The activation energy of alumina leaching is 19.53 kJ/mol, and the leaching process is controlled by chemical reaction. Pressurized alkali solution can not only efficiently leachate alumina from the spent catalyst and enrich platinum, but also reduce the reaction time and increase reaction rate.

Feb 11, 2022

By E. Milosavljevic, C. H. Bucknam, K. L. Gabby, T. C. Eisele

"Since mercury is chemically similar to silver, it tends to dissolve along with the silver and gold during cyanide leaching. Ultimately, mercury is recovered along with the silver as mercury/silver/gold amalgam, which requires retorting to remove the mercury prior to refining the silver and gold. A possible approach to separating mercury from silver and gold in cyanide leach solutions is to take advantage of the replacement reaction between [Hg(CN)4]2- and Ag2S, which results in precipitation of mercury as HgS while dissolving silver as [Ag(CN)2]-. Results are presented demonstrating that mercury can be removed from cyanide solutions with high effectiveness while, at the same time, recovering additional silver in solution. Initial experiments with static flasks in the laboratory showed a high degree of mercury removal could be achieved. Results using actual metallurgical plant products in bottle roll tests indicate the process works on a larger scale, but also results in significant gold losses if the solution being treated has high gold levels, such as carbon stripping pregnant eluent solution. IntroductionThe dissolution of mercury along with precious metals during cyanide leaching is a long-standing problem, which can result in significant mercury toxicity issues (Washburn, 2003). Mercury is first dissolved by the cyanide solution, and then, since it has a great deal of chemical similarity to silver, it follows silver throughout the concentration and recovery processes, ultimately being recovered as a silver/ mercury amalgam when the metal is precipitated by either the Merrill-Crowe process or by electrowinning.While it would be desirable to either prevent mercury dissolution entirely while still allowing silver dissolution, or to selectively capture mercury before the precious-metals recovery step, there is not yet an effective and economically practical approach to doing this (Grosse, 2003; Ravichandran, 2004; Misra, 1998; Pai, 2000). There are a few processes that have been proposed, such as differential adsorption. While activated carbon, as used in the carbon-in-pulp process, is not highly selective between mercury and silver (Washburn, 2003), it may be possible to achieve some separation by selective elution of the carbon to produce high-mercury and low-mercury eluates (Bunney et al., 2010). Certain synthetic resins were shown to be selective for gold but are more expensive than carbon, requiring special equipment, and have not yet been shown to be selective for mercury (Grosse, 2003). There may be potential for differential dissolution approaches, as thiosulfate leaching does not dissolve mercury sulfides as readily as it dissolves gold (Oraby et al., 2010), and it is possible that it may be similarly more selective for dissolving silver relative to mercury. Some work has also been done with selective precipitants, such as sodium polythiocarbonates (Bucknam, 2007), and 1,3-benzenediamidoethanethiol (Matlock, 2002). Common problems with these approaches include introduction of a solid:liquid separation step, reagent costs, the need to measure the mercury concentration for process control for minimizing silver losses, and regulatory requirements to retort otherwise stable mercury concentrates."

Jan 1, 2015

By Dr. -Ing. Rainer Alles

Introduction Belt conveyors usually run in a straight line. The correct alignment is a major criterion for reliable functioning and optimum running properties. Any misalignment of the conveyor, especially mistracking of the belt, can have many negative effects. As a consequence of this, damage can occur on the belt and conveyor, some material can he thrown off at the edges and serious running problems can arise. In the worst case the belt can come off its supporting structure so that operations are brought to a halt. The absolutely straight alignment of a belt conveyor is actually impossible so that on closer observation every belt conveyor contains more or less sharp curves. Whereas on non-movable conveyors the deviations from the straight can he kept within the range of practical measuring accuracy by careful installation, movable conveyors in surface mining or belt systems in difficult terrain often contain curves that are easy to see with the naked eye. Below ground, too, alignment cannot always achieved to a desirable extent or is changed by geological faults over the years. Despite these unwanted curves, most belt conveyors perform their function reliably. In view of the belt tension, the belt tends to take the easiest path. This in general is the shortest distance between the pulleys on which the belt is tensioned and bent. This means for example that for a curve radius of 10,000 m over a flight of 100 m the greatest deviation from the ideal line is as much as 12 cm. And a figure of this magnitude cannot normally he accepted. In such cases, use is made of guide devices to properly train the belt if it doesn&apos;t center itself anyway. If it&apos;s possible to control the belt position over such unwanted curves. it can also he expected that the belt tends to follow the desired curved path within certain limits. I&apos;d now like to cite a few examples to illustrate the ways and means of guiding a belt conveyor in curves. Cost-effectiveness The advantages of belt conveyors, in particular for longer conveying distances and mass flows have been known and undisputed for some time. However, there are often obstacles standing in the way of the concept of straight routing. If a belt conveyor is to bypass elevations or existing buildings or to follow the seam of underground deposits or a predetermined path, then substantially tighter radii and longer curves are desirable or necessary.

Jan 1, 1993

By Thomas A. Mekelburg

Due to a tight ash constraint on the clean coal product and difficult middlings washability characteristics, a considerable amount of coal was being lost in the jig middlings at the Monterey No. 2 Mine. An investigation was conducted into circuitry to recover this lost coal with minimal effect on the total clean coal ash. A reverse two-stage hydrocyclone system cleaning at low specific gravities was selected. This system is currently recovering approximately 5.8 kg/s (23 tph) of 11.5% to 12.5% ash coal. The specific gravity of separation for the system is about 1.5 and the probable error is 0.13.

Jan 1, 1984

A portable electronic instrument was developed which will measure change of longitudinal wave velocity with change of uniaxial stress in rock columns. The instrument is a solid-state device powered by nickel-cadmium batteries. It uses a probe of two piezo-electric crystals spaced inches apart to send and receive a pulse through a stressed rock. A one-inch cathode ray oscilloscope visually displays the longitudinal wave. A reference chart is used to find the stress. Laboratory results have indicated that the average stress on a sandstone column can be found to within 35 psi. The feasibility of using this instrument to determine stresses in mine pillars is to be studied. The instrument may be used to investigate physical properties of rock.

Jan 1, 1970

By Fred Pena

The VERTIMILL has proven itself to be a reliable performer in heavy duty industrial applications. Applications have been extensively used in the mining industry, flue gas desulfurization applications, and industrial minerals field. The machine is a vertically stirred machine that utilizes a screw operating in a grinding media. Grinding media types have ranged from several sizes of steel balls as the most common to pebbles or ceramic media. Mesh-of-grind and final product size are the determining criterion for the selection of the media size used. Product size consists have ranged from very coarse to super-fine grinds of less than 25 microns. Savings in consumption of power, grinding media, and liners when compared to a conventional ball mills, have been realized. Savings in consumption of reagents have also been demonstrated.

Jan 1, 1992