Search Documents

By Donald C. Wotring, Douglas A. Gabriel, Michael G. Vitale

"The Northeast Ohio Regional Sewer District (NEORSD) recently completed the 24-foot diameter Euclid Creek Tunnel using a steel-fiber reinforced concrete segmental lining. During construction HMM, the McNally/Kiewit JV, CSI/Hanson JV, and the NEORSD performed a test program to evaluate replacement of steel fiber with synthetic fiber. A section of synthetic-fiber-reinforced cast-in-situ lining was also placed as part of the permanent works for the starter and tail tunnels. Laboratory and field testing were performed on two complete segmental rings reinforced solely with synthetic fibers. This paper summarizes the testing program, construction, and results of the synthetic-fiber-reinforced CIP lining and concrete segments. INTRODUCTION The principal feature of the Euclid Creek Tunnel (ECT) project is a CSO storage tunnel that is one component of the Northeast Ohio Regional Sewer District’s (NEORSD) Easterly CSO storage and conveyance system. The tunnel, shafts, and appurtenant facilities will be used for the collection and storage of CSOs from the northeastern part of Cleveland, Ohio and subsequent conveyance to the NEORSD’s Easterly Wastewater Treatment Plant for treatment. The ECT project includes five drop shafts that extend as deep as 220 feet below the ground surface. The ECT alignment and shaft locations are shown in Figure 1. Traditionally in northeast Ohio, tunnel excavations were supported with a two-pass system using steel ribs and timber lagging, followed by cast-in-place concrete. Control of rock overbreak proved difficult with large-diameter two-pass operation, and invert degradation led to train derailments. To mitigate these risks, the ECT was supported using one-pass, precast, bolted, gasketed concrete segments reinforced with steel fiber alone. Tunneling operations were very successful and experienced no significant delays or claims. As a result of the positive ECT experience with steel fiber-reinforced segments, Hatch Mott MacDonald, LLC (HMM), McNally/Kiewit (MK) joint venture, CSI/Hanson (CSI/H) joint venture, and the NEORSD performed a test program to evaluate replacement of steel fibers with synthetic fibers in segmental rings. This paper presents the laboratory and field testing program, construction, and results of the synthetic-fiber-reinforced cast-in-place (CIP) lining and concrete segments."

Jan 1, 2016

By David A. Campbell

There has been a long history of ironmaking on the North East coast of England centered around the River Tees. The industry developed here because of the availability of good coking coals to the North in Co. Durham, and the discovery in 1851 of ironstone in the nearby Cleveland Hills, South of the .River. Cleveland ironstone is relatively poor in quality, with an iron content not exceeding h% and high proportion of sulphur and phosphorous. The iron exists in chemical association with alumina and silica, and physical beneficiation processes involve a serious loss in iron unless the upgrading is limited, when the economics of the process become doubtful. Over the years, richer foreign ores have replaced the local ironstone, and the last operating mine was closed in 1964.

Jan 1, 1982

By Ray Brainard, Adriana Ventimiglia, Amanda Kerr

Preliminary design is underway for a new Southern Nevada Water Authority (SNWA) project that will ensure one of America’s most reliable water systems by providing continued, reliable water service to existing and future customers. The Horizon Lateral is a $1.6 billion water transmission pipeline that includes 7–10 miles of 108-inch finished diameter rock and soft-ground tunnels. The tunnels will traverse volcanic rock in or around the McCullough Mountain Range and the surrounding alluvial basin. The tunneling community will find relevance in hearing about this critical infrastructure project from a leading wholesale water utility owner with a proven track record for on-time, collaborative projects.

Dec 1, 2022

By Whitmell J. Smithwick

Lime is one of the most extensively used chemicals in industry. Other than sulfuric acid, it is used in greater quantities than any other man-made industrial chemical. In 1974 there were 20,368,000 tons of lime used in the United States, which amounts to approximately 190 pounds for each man, woman and child in our nation. Lime also is perhaps the most diversely used of any industrial chemical. It is used in such areas as pharmaceutical, chemical, steel making, glass making, production of copper and aluminum, sugar refining, agriculture, construction, ecological endeavors, potable water treatment and sanitation. Figure I lists the major uses of lime for 1974, which is the latest year for which this data is available. The impact of the use of lime for ecological reasons did not show up to any appreciable extent in 1974, but we expect this to be a significant factor within the next few years. Fortunately, in the United States and also in most of the world, there are many deposits of high quality limestone available for the production of hood quality lime. For this discussion, we will assure that a limestone of a suitable quality and size consist will be available in a storage bin or stockpile near the kiln. Quality requirements for the lime product will be covered. We also will give a brief description of the three most popular types of lime calcining systems, how they function, and expected lime product quality from each of these. Commercial fuels and major accessory equipment will be discussed briefly.

Jan 1, 1976

By J. L. Kohler

Control circuit failures contribute significantly to continuous miner downtime. The time required to put the machine back into production is a function of the time required to diagnose the problem, obtain parts, and make the repair; of these, the diagnostic time is often the largest. A microprocessor-based system with the ability to diagnose all of the common control circuit failures was designed, installed on a continuous miner, and tested. This paper summarizes the development of the diagnostic system, and provides examples of the system's diagnostic capabilities. Implementation issues and the hardware used for the prototype are briefly described. Finally, comments on the system's performance are presented.

Jan 1, 1993

By Richard Seal

Nabarlek is situated in the Arnhem Land Aboriginal Reserve about 270 km due east of Darwin in the Northern Territory of Australia. During the dry season (May to November) Nabarlek is accessible from Darwin over the Arnhem Highway-- a distance of 330 km. Throughout the wet season (December to April), except for a few days, access is provided by aircraft from Darwin to the Nabarlek airstrip. Because of the limited access during the wet season, reagents and supplies have to be stock- piled for six months on the site to maintain operations. With the mine and plant being remotely located on private Arnhem land with very limited access outside the site fence, operating personnel are flown to Darwin every six days for their days off.

Jan 1, 1980

By Mahmud Esad Uluer, Seyed Hassan Amini, Aaron Noble, Matt Shigo

Airborne coal mine dust is an unintended and unavoidable result of coal extraction operations that raises notable health and safety concerns. Modern mining techniques utilize several dust mitigation strategies, and the flooded-bed dust scrubber (FBS) is one such technology used extensively on continuous miners. The conventional static panel filter, instrumental in most scrubber designs, is fundamentally limited in collection efficiencies due to a high clogging rate and a tradeoff between mesh density and airflow rate. To overcome these deficiencies, a novel vibrating mesh panel is proposed. In this study, a laboratory-scale dust scrubber unit was used to investigate the efficacy of concept as compared to that of a static mesh. A statistical design of experiments study was first used to determine the effective vibrational parameters and scrubber operational parameters on dust collection and clogging mitigation. Optimized results from this study were then evaluated against those of a static mesh to determine performance improvement while investigating the mechanisms controlling dust collection and particle department through the scrubber system. Results show that the vibrating mesh conditions and higher water flow rates led to an improvement in the collection efficiency of the scrubber system. Compares to a static-mesh, the vibrating mesh FBS showed a significant reduction in pressure drop across the mesh screen indicating lower air loss through the test duration. Overall, the findings confirm that vibrating filter mesh reduces filter clogging while maintaining high collection efficiencies. This research supports further technological advancement in mine dust mitigation technologies.

Dec 27, 2023

By P. C. Thakur

The productivity in coal mines, measured in terns of the output per manshift depends largely on the efficiency and speed of men and materials transport between working faces and the surface. The mechanization of coal winning and material handling processes has led to a great rise in the mine productivity (1). Early applications of power in U. S. coal mines were mainly electrical. The excellent traction available with the DC motor and the ease of the distribution of the DC power have made trolley wire installations for haulage very popular. In shallow mines with very limited emissions of methane it did not constitute a major hazard but as mine depths increased and corresponding emissions of methane also increased fire and methane ignition hazards have become very serious. Conveyors have proved economic where intense mechanization of coal faces generates a large output of coal from a single face, but the fire and respirable dust hazard associated with them are no less serious. Recognizing these shortcomings, the Federal Coal Mine Health and Safety Act of 1969 laid down numerous provisions for the safe use of trolley-wire haulage and conveyors (2) which generally improve safety but in some cases complicate mining operations and have decreased productivity significantly since 1969. In course of time as coal mines become deeper and hence gassier and as the emphasis on safety increases it would be inconceivable to use trolley-wire haulage under ground as already witnessed in several other countries with deep coal mines. With rising capital investments and cost of the protection against fire and respirable dust, the use of conveyors may also have to be limited to special areas, e.g. main entries. Indeed, there are only two alternatives available, namely; (1) Degasify the coal seams prior to mining and use conventional electrical power, or (2) Develop alternate sources of power which would be safer and yet efficient and cheap.

Jan 1, 1975

By Robert A. Irvine

Traditionally, cost effective gains in the capacity of material handling systems were a result of increases in equipment size. In general, the use of maximum capacity components in a system optimizes the production "costs per ton." The trend-"Bigger is Better" will continue in material handling equipment. Since it is rare for plant operators to lament an over abundance of screening capacity, one can safely predict that vibrating screens will follow this trend. Large Vibrating Screens - The Challenge Large vibrating screens represent a unique challenge for Manufacturers, Plant Designers, and Plant Operators. The inherent mode of operation for vibrating screens is self-destructive. More often than Manufacturers admit, Designers plan for, or Operators staff for, a vibrating screen succeeds and self-destructs. This is a problem. It can magnify with larger vibrating screens.

Jan 1, 1983

By Satya Harpalani

The four most important parameters controlling the flow of gas in coal are the gas content, permeability, diffusion coefficient and cleat characteristics. Estimates of these and, more importantly, a knowledge about the variation in their values over time are required for simulation of long-term gas production. This paper describes experimental techniques to determine each of these, along with their time dependency, under simulated in situ conditions. It is shown that the permeability, diffusion coefficient and the cleat aperture values are not constant as usually assumed to be. There is a significant variation in their values as a result of changes in the microstructure of coal associated with release and flow of gas.

Jan 1, 1995

By L. C. de Kooker, K. Esmaeili, I. Musonda, M. Ferentinou

A numerical investigation of the effect of pore pressure regime on the safety factor and the critical failure mechanism is presented for fly ash storage facility. Pore pressures’ measurements from standpipe piezometers and pore pressure estimated from seepage analysis are used to compare the factor of safety for a fly ash slope. This was applied for considering static and seismic scenarios. A probabilistic approach was applied to account for the uncertainties resulting from the limited data available and support a qualitative risk assessment evaluation. Slope stability analysis is conducted in two and three dimensions, adopting the limit equilibrium analysis approach, and also a finite element seepage analysis, to assess the stability of the slope. The two-dimensional cross-sections were extruded to three-dimensional models to estimate the factor of safety and associated shear failure. The results from the performed analysis suggest an increase in safety factor values of 5%.

Mar 27, 2024

By G. J. C. Young

The paper describes the replacement of a conventional filtration, clarification and zinc precipitation plant by a carbon in pulp (CIP) electrowinning plant, with the objective of improving the recovery of gold from cyanide leached, acid plant calcines. The discussion covers the early laboratory studies to the design and erection of the full scale plant. Particular emphasis is placed on the problems encountered with commissioning and the strategies which were employed to solve them.

Jan 1, 1982

By U. Heuer, B. Rathmann

Many mining operations have gained an impressive expertise in trouble shooting and maintenance with their existing fleet over the years. Whether it is an in-house maintenance group or an external service group - most of the systems weak points are well known and can be corrected by maintenance personnel. As some of these issues get more and more serious each year, too much time is lost in unscheduled downtime, often taking hours to be repaired and to find the failure with obsolete diagnostic tools (Fig. 1.). Many of the breakdowns result from failures that cannot be detected in advance. The maintenance system is much more reactive than preventative. The state of the art of mining equipment today uses advanced, efficient, and reliable systems for electrical drives, control and diagnostics of the machines. The demand for highly sophisticated solutions on such mining equipment is well known. Mining operators need to ensure the highest level of productivity, lowest operating costs, least maintenance and highest reliability in a drive system. The paper will introduce you to the state of the art of drives technology for dragline (Fig. 2) and shovel mining equipment (Fig. 3).

Jan 1, 2007

By Karl C. Dean

The current emphasis on environmental problems has focused attention on the massive nationwide accumulations of mine, mill, and smelter wastes that represent potential air and water pollution hazards. The pollution hazards can be reduced or eliminated by utilization or stabilization of these wastes. The U.S. Bureau of Mines, since the inception of the Solid Waste Disposal Act of 1965, has been conducting research to determine the practicality of various utilization and stabilization procedures. Investigations include partial extractions of desirable waste components and full utilization of the wastes as simulated soils or in ceramic or other structural products. Chemical, vegetative, and combined chemical-vegetative methods of stabilization have been actively studied. This report updates information previously developed by the Salt Lake City Metallurgy Research Center and presents the current status of antipollution solid waste work 1/,2/.

Jan 1, 1970

By C. Dirscherl

"Declining ore grade, leading to increased material transport and plant throughput requirements, is one of the major challenges in the current mining environment. This is accompanied by rising energy and labor costs, decreasing plant productivity and the requirement for highest plant availability. Siemens’ answer is the latest gearless drive technology for grinding and conveying. Gearless drive solutions are surpassing the mechanical limits of conventional drive systems serving to utilize the principle of economies of scale. By elimination of various components of the drive train the maintenance activities and spare parts inventories are reduced. The advantages are culminating in the incomparable availability of the Siemens’ gearless drive technology of 99.46 to 99.71% - as confirmed by real operational data from the Antapaccay mine in Peru. It was the first plant worldwide to use gearless drives for both applications. KEYWORDS: Gearless Mill Drives, Gearless Conveyor Drives, Availability, SAG Mill, Ball Mill, Overland Conveyor, Antapaccay INTRODUCTION – THE GEARLESS PRINCIPLE The principle idea behind a gearless drive system is to reduce the number of components and diversity of parts. Especially those components that are at the edge of current manufacturing or power limits are eliminated. The used equipment provides the possibility to scale up and increase the power transmitted to the driven machine. This finally results in a possible increase of throughput respectively transported or processed material. In order to apply this principle of simplification we will take a look at the components of a conventional drive system consisting of: - Driven equipment (mill, conveyor, slurry pump…) - Components altering the rated speed (gearboxes, girth gear / pinion) - The electric motor - Starting devices for the motor (VSD, CCV, LRS, clutch…), which are necessary because a direct across-the-line start of high power motors with load would result in a significant drop in the line supply voltage - Alternatively a variable speed drive (VSD) or cycloconverter (CCV) to utilize the possibility of speed variation during operation - The electrical supply system (cables, switchgear, transformers, protection equipment) Intermediate gearboxes are not required when a motor is used with a rated speed that directly matches the speed requirement of the driven equipment. Furthermore the VSD can be used to smoothly start the motor and to vary speed during operation, which means that it satisfies both requirements."

Jan 1, 2015

By C. Woofter

Quarry operators must continue to change and adapt environmental compliance methods to meet the increasingly demanding regulations. To fulfill industry needs, a computer-based decision support system is being developed to facilitate decision making that mine operators are required to make regarding environmental responsibilities. This system can help to determine permitting and compliance measures needed for air, surface water, groundwater, noise, aesthetics, vegetation, wetlands, hazardous wastes, storage tanks and wildlife habitats during the development, operation, and closure phases of mining. Operators will utilize the system's user-friendly interface consisting of mouse driven responses and limited keyboard entries on a desktop computer. The system is easy to upgrade according to the user's needs and changes in current laws and regulations. Data input models, user interfaces, and support of decision making are explained. The program permits inclusion of the decision maker's own insights through "what-if' analysis, in which the user can change ad hoc entries and check the related consequences. Using this approach, the user has complete control over all steps of the decision making process. A storm water example is selected to demonstrate the potential benefits of the support system to environmental decision makers.

Jan 1, 1995

By Georgene Renner

With more than 800 booth spaces sold and 540 exhibiting companies displaying their wares, there was something for everyone on the exhibit floor of the 2014 SME Annual Meeting in Salt Lake City, UT Feb. 23-26. The following is a sample of what was offered at the 2014 meeting.

By V. Svalbonas

Presently the U.S. mining industry is very conscious of costs. It is timely, therefore, to review the dominant specifications used in the industry for procuring large size-reduction equipment. These are compared with other specifications and procurement methods, such as ASME and DOD, using the criteria of resulting costs, safety/ quality, and fitness-for-service.

Jan 1, 1987

By J. Gathje

Normal process development for pressure preoxidation treatment of refractory gold ores starts with laboratory batch autoclave tests, followed by operation of a continuous autoclave pilot plant for confirmation of the various process options. This scheme will generally provide good information showing the effects of such variables as grind size, time, and temperature, and will indicate whether autoclave preoxidation will produce solids that are amenable to cyanidation for gold recovery. However, several recent test programs conducted over the last three to four years have shown that the cyanide leaching responses of treated solids from the batch tests can differ considerably from those achieved by the continuous pilot plant autoclave. Examples are provided to demonstrate these differences and to show the importance of extending the laboratory investigations to include the use of a semicontinuous autoclave test procedure. A test case is cited in which this procedure provided data that could not be obtained from batch tests.

Jan 1, 1995

The use of coal as a fuel causes air, pollution in; a number of different forms, and in nearly all stages of its, handling, preparation, storage, use and-disposal of its residue. First let us consider the handling of coal. As shipped, particularly to large utilities, it is run-of-mine bituminous made up of large chunks as well as pulverized particles. Because it 'is in an open car or barge, it is subject to the action o winds and the small particles may be blown around adding to the-particulate load in the atmosphere. Mien un¬loaded from the barge or car, there is again an opportunity for the wind to blow the fine particles around. All of us I am sure have seen a barge at the dock of a utility plant being unloaded by a clamshell bucket. This, after grabbing its load from the barge, lifts it some 60 or 70 feet and, then drops it on a conveyor, which carries the coal to a storage area.

Jan 1, 1964