Search Documents

By J. E. Urosek

Decisions made during a response to a mine fire or an explosion greatly affect the final outcome. The safety of miners should be the primary concern with accounting for all of the miners the first issue for resolution. If miners have not safely evacuated from the mine, the last known location of the miners at the time of the event and anticipated travel routes are primary exploration areas. After the mine is evacuated, there are many very important decisions that must be made quickly and often under great stress. It is critical that the mine operator establish an orderly method to direct the mine emergency response. Designation of a Command Center, staffed with personnel charged with developing plans, is a common method of establishing control. Scheduling of key mine managers will be critical, since decisions must be made 24 hours a day and people working for extended periods with little or no sleep do not always make clear or cognizant decisions. Internal communications, passing information on to subsequent shifts, and external communications with families and media must be accurate and timely. Assembling resources for responding to the mine emergency is critical for an effective response, and pre-planning can pave the way to a successful recovery. Sampling mine gasses and accurately determining the composition of gas mixtures is a common tool used to develop response plans in all fires and explosions. It is essential that preparations for emergency situations are made well in advance of a disaster. Effective communications are essential for mine management to successfully respond to a mine emergency. This paper discusses some considerations which need to be addressed in directing a response to a mine fire or explosion.

Jan 1, 2009

By J. M. Scharer, Bruce E. Halbert, Pettit. Carol M., Lysane Bolduc

The ratio of neutralization potential (NP) to acid production (AP) ratio is often employed for predicting acidic discharges from waste rock dumps. The available NP was evaluated in laboratory studies of limestone dissolution in simulated acidic mine water. The available neutralization potential strongly depended on the particle size. Using limestone particles of 114" (6.4 mm) or greater, less than 20% of the total neutralization potential was exhausted at the onset of acid conditions. Apparently, the dissolution of limestone became mass transfer limited. Under mass transfer limitations, the rate of pyrite oxidation may exceed the rate of neutralization by buffering minerals. The implications concerning the controls on limestone dissolution were examined using a geochemical predictive model for sulphide mineral oxidation in waste rock. The results have shown that in case of heterogeneous waste rock piles the NP/AP ratio is a reliable indicator for short-tam predictions only. Kinetic data on the depletion rate of the neutralizing minerals and geochemical modelling suggest that waste rock environments with NP/AP ratios as high as 5.0 may turn acidic in the long term.

Jan 1, 2000

By T. Rasmussen, T. G. Jørgensen, T. Fischer, R. K. McLimans, C. Knudsen, D. Frei

Ilmenite-bearing paleo-beach deposits were discovered in Jylland, Denmark using a combination of Ground Penetrating Radar (GPR), portable X-ray fluorescence (XMET), bulk XRF analyses, Computer Controlled Scanning Electron Microscopy (CCSEM), and wire line logging. The Miocene-age paleo-beach deposits are located below a thin Quaternary cover in a region of very moderate relief and essentially no outcrop demanding unique approaches in exploration. Initially, an isopach map of the Quaternary is prepared from existing water well data. A geological model for likely occurrence of Miocene paleo-beach deposits is generated and the coincidence of thin Quaternary cover and potential paleo-beach deposits define targets for detailed exploration. The defined targets are traversed with GPR to identify paleo-beach structures which are then used to define a drilling program. This methodology located a paleo-barrier island at the Vorslunde location with more than 10% ilmenite in the sand. During the drilling process, the TiO2 and heavy mineral contents of the sand were logged every meter with a portable XRF unit (XMET) and subsequently calibrated more accurately by comparison to bulk XRF and CCSEM analyses for selected samples. The bulk XRF data also provided more complete compositional information. Insitu determination of geology, heavy mineral abundance, and corroboration of the XRF logging was done using wire line logs, a combination of spectral gamma and induction conductivity logs. Detailed characteristics (abundance, grain size, shape) and chemical composition of minerals was determined by the GEUS CCSEM methodology (Frei et al, this vol.). The average weight percent TiO2 for all Ti-minerals is 62%, 60% excluding rutile. That elevated TiO2 content (>> ilmenite stoichiometric value, ca. 50 %) indicates that ilmenite experienced an iron-leaching environment. The source of the sand deposit was investigated by dating contained zircon. The results show that the likely sources of zircon are in southern Norway and southwestern Sweden with common zircon ages of ca 1100 Ma. and 1500 Ma.

Jan 1, 2005

By Andrew E. Nevin

The government of India convened a precedent-setting meeting in New Delhi on Nov. 12, 2001.The meeting brought together regulators and the mining industry in an attempt to fix the industry’s mine development problems in that country. More than 150people attended the all-day session. Ram Vilas Paswan, Minister of Coal and Mines, chaired the meeting. Ravi Shankar Prasad, Minister of State for Coal and Mines, was also present. The secretary of the Department of Mines and the Joint Secretaries and Additional Secretary also participated. The Department of Mines’ mandate is for economic growth: to get new mine development going and to make investment in mining attractive for both domestic and foreign-owned companies.

Jan 1, 2002

By Verya Nasri

This paper presents analysis of damages and rehabilitation design for three major French rail-way tunnels built in mid-19th century. The La Nerthe tunnel underwent ovalization deformation with excessive displacement at the springline, and pinching and bursting of the liner bricks at the crown due to tectonic residual stresses with very high lateral earth pressure. The Saint-Louis les Aygalades tunnel invert was subjected to undulatory deformation resulting in tracks misalignment, which was caused by non-homogeneity of mechanical and hydraulic properties of the ground. The Roches de Condrieu tunnel required widening to comply with the increase in dynamic envelope of trains due to their larger cross section and higher speed. The applied rehabilitation methods and constraints of work in these busy mainline railway tunnels have been discussed in detail.

Jan 1, 2008

By K. Ward

The Environmental Protection Agency (EPA) is beginning to provide compliance assistance visits to various industries, including mining, for Emergency Planning and Community Right-to-Know Act (EPCRA) compliance. The EPA inspectors may consist of a multi-media team deployed to review systems and procedures for EPCRA Sections 302, 304, 311, and 312. The Team’s focus may include emergency response plans, training programs, qualifications of personnel, and release notification protocols. This presentation takes a look at the EPCRA compliance challenges faced by Arizona copper mining and processing facilities.

Jan 1, 2001

By William A. Dupree, Mark J. Schultz, William J. Francart

Maintaining intake escapeways clear of contaminants from mine fires has been an issue for many years. Removing fire sources from these entries reduces the risk of contamination greatly. In recent years, concerns have been raised related to contamination of the intake escapeways by leakage when fires occur in adjacent airways. This paper discusses measured leakage rates for multiple stoppings at various pressure drops across stopping lines in a number of actual coal mines. Also addressed are methods for reducing the contamination risks for the intake escapeways, considering the ventilation system employed. The Effects of Air Leakage The effects of air leakage through ventilation controls has been well documented. While normal leakage is expected through stoppings, overcasts and other structures, abnormally high leakage results in an inefficient ventilation system and can increase operational costs for a mine. In addition, excessive leakage results in less control over mine ventilation airsplits. This may compromise the isolation of mine escapeways, and allow adjacent entries to be rapidly contaminated by products of combustion in the event of a mine fire. A study was conducted at ten mines in which air pressure and quantity measurements were taken near the active sections. The method used to construct the ventilation controls to separate airways was also noted. Stopping Construction Table 1 shows the type of stopping construction commonly used in the 10 mines included in this study. Main entry stoppings were normally built with mortared joints (wet stacked) with sealant applied to the high pressure side of the stopping. In most cases the entire face of the stoppings were sealed. In one case only the joints between blocks were sealed but the perimeters were sealed in all cases. Some mines also sealed the low pressure side of the stopping. Solid blocks were normally used for main entry construction and hollow blocks were sometimes used for longwall panel development. [ ]

Jan 1, 1993

By Bhaskar B. Thapa

The design of the Caldecott 4th Bore, located along State Route 24 in Oakland, California, is based on the principles of the New Austrian Tunneling Method (NATM). Typical NATM initial support design practices used in Europe were adapted for this project to account for U.S. conditions and requirements, such as degree of experience with NATM construction, the prevailing contractual environment, and preferences for contractual simplicity. Key design features are: (1) support selection criteria based on ground behaviors and ground conditions; (2) a prescriptive design with allowance for support adjustments based on observations during construction; and (3) organization of support requirements into only four major support categories, while permitting some adjustment for variations in ground behaviors and conditions using a few subtypes and additional support measures.

By G. G. Gold

A leach pad’s fluid flow characteristics greatly affect the recovery of metals from heap leaching. However, because there are other factors such as particle size distribution, application rate and method, and chemical reactions to consider, mining companies often overlook potential problems associated with fluid flow until it is too late. In an effort to better understand the dynamics of fluid flow in leach pads, a series of experiments were preformed using temperature probes. A model leach pad was set up using a particle size distribution, fluid application rate, and application method common to modern leaching methods. Variable water temperatures were applied in succession and data gathered from the three dimensional grid of temperature probes built in to the model. Current work is analyzing these data along with visual observations of the model, computer simulations, past mining experiences, and other related research, in an attempt to develop a low cost test that could be performed prior to large scale leaching to determine the fluid flow characteristics of a particular ore. This paper will summarize the work and findings to this point as well as suggest areas of additional related research.

Jan 1, 2004

By Daniel J. Dobbels, Eric R. Drooff, James R. Wheeler

Construction of Boston’s C11A1 Section of the Central Artery (I-93)/Tunnel(I-90) Project beneath the existing MBTA Red Line Subway at South Station required excavation to depths in excess of 33.5 m (110 ft) through permeable sand and gravel subject to almost 27.4 m (90 ft) of hydrostatic groundwater pressure. As tacked drift tunnel underpinning system was designed to provide positive support to the active station prior to mainline tunnel construction. As part of this system, a permeation grouting program was developed to facilitate tunnel excavation. This paper describes the design and implementation of the grouting program, in sit testing, and the overall performance of the grouted soil mass.

Jan 1, 1999

By Christopher Snee

??care has to be taken that the design is driven by sound geological reasoning and rigorous engineering logic rather than by the very attractive images that appear on the computer screen.??Hoek 1999 Design of a cavern is inextricably linked to the engineering geology of the site. The importance of sound geological reasoning will be illustrated by transportation projects in New York City where there are proposals for at least 11 caverns. These caverns have been the subject of advanced exploration techniques and geological interpretation but even so the raw data falls short of the sophistication of modern numerical methods. This paper will give geological explanations for the engineering characteristics of the rock in New York City which will provide guidance for practitioners when approaching cavern design in New York and elsewhere.

Jan 1, 2008

By Ross K. Digby

The Victorian Tunnelling Centre (VTC) has evolved its purpose from purely training workers, to a tunnelling industry education city. The VTC has now focused its activities on the areas of technology; education and training; applied research; and career education. were identied as the hus around which activities would e conducted to create a tunnelling industry education city. The VTC provides ustralias tunnelling industry with an education facility that not only provides laour training, ut enales the industry to come together to meet, participate in product launches, undertake research, work with new technologies and promote tunnelling careers.

Jun 23, 2024

By Tom Bruington

This paper discusses the accuracy of determining the quantities of gold and silver on activated carbon in various stages of process for typical precious metals flowsheets. Accurate plant performance evaluation depends upon reliable estimates of carbon and precious metals inventories. The sources of sampling error are identified and methods of reducing them discussed. Several case studies illustrating the sensitivity of flowsheet performance to sampling error are presented.

Jan 1, 1991

By D. Babich, L. Alcorn, E. Spencer, A. Smith

Noise is one of the most pervasive health hazards in mining. A compilation of Mine Safety and Health Administration (MSHA) noise survey data for Fiscal year 1990 shows that approximately 40% of the total samples taken for longwall occupations exceeded the Permissible Exposure Limit (PEL) of 100% [Gigliotti et al. 1991]. In order to properly determine workers’ exposures on longwall coal mining systems, it is necessary to provide accurate baseline measurements for these mining systems. This research was designed to develop guidelines and test procedures for identifying all noise sources that are major contributors to the underground noise exposure of longwall coal mining system workers. Once the high noise sources are identified, promising engineering controls can be tested and evaluated to reduce the noise of the sources. The measurement system used to analyze the noise sources included stationary dosimeters in a documented repeatable pattern and a time-motion study of the cutting cycle and operator’s work cycle. Significant results from the underground measurements show that the highest sound levels recorded are at the stageloader discharge segment and tailpiece controls and remained at about the same level throughout the test.

Jan 1, 2007

By John Lovering

The Afton property is located 180 air miles East-Northeast of Vancouver and nine miles West of Kamloops, a city of 60,000 people, in South Central British Columbia, Canada. The mine is adjacent to the Trans-Canada Highway at an elevation of 2,200 feet above sea level. The orebody is a porphyry, copper deposit that has undergone supergene alteration. The-major economic minerals in the supergene zone are native copper and chalcocite with chalcopyrite and bornite in the hypergene areas. The grade is one percent with an overall copper distribution: 70% native, 25% chalcocite and 5% chalcopyrite with bornite and covellite. The ore also contains important, but variable amounts of gold and silver.

Jan 1, 1985

By T. N. Moore, E. M. De Souza

Vibratory hand-tools can produce Hand Arm Vibration (HAV) Syndrome in their operators. This disease, often called Vibration White Finger, can cause varying levels of hand-arm discomfort and, in severe cases, impairment. In addition to the human suffering, there are also significant economic repercussions for industry. These include reduced operator efficiency, lost time through increased absenteeism and increasing compensation awards. In the mining industry, jackleg rock drills are a particularly troublesome source of hand vibration exposure. As a result, a significant amount of work has focused on redesigning rock drill handles to minimize hand-transmitted vibration. This paper details the results of a study undertaken to determine the effectiveness of using elastomer covered ("cushioned") handles in place of the standard steel design. The results indicate that, for a particular cushioned design, the overall acceleration level experienced at the hand-handle interface can be reduced by as much as a factor of three, relative to the steel handle. It is also shown that this reduction takes place predominantly in the frequency range above 500 Hz, with performance improving with increasing frequency. Qualitative evaluation of the cushioned handles by the drill operator indicates a significant increase in comfort over the standard steel handle.

Jan 1, 1992

By C. Maltesh, P. Somasundaran

The ever increasing need for treating fine complex mineral bodies has led to the evolution and rapid development of advanced processing techniques for fine grinding, classification an if mineral separation and purification. With the introduction of these new technologies and understanding of underlying fundamental principles, mineral processing is now being applied to materials ranging from ceramics and composites to superconductors. In this review, current and potential applications of mineral engineering techniques to advanced materials processing are discussed. Particularly, material processing involving ultrafine grinding, dispersion and flocculation and thin film formation is examined. Novel techniques of solid/liquid separation involving manipulation of interfaces and use of high intensity high gradient superconductor magnetic equipment for solid/solid separation are discussed.

Jan 1, 1990

By S. B. Bhagwat

The United States has abundant coal resources that could last at least another century. and probably longer at present consumption rates. Geographically, the coal resources are distributed over the entire nation including Alaska, although there are no coal deposits in the highly populated areas on the two coasts. This allows free access to the coal, but makes transportation more expensive. Not all coals can be utilized equally because they differ vastly in quality. The sulfur content of coals, considered as the most detrimental acid rain-causing element, varies from as low as 0.3 percent in some areas of the western U.S. to 5 percent or more in parts of the Midwest. The chlorine content, which causes corrosion of plant hardware, also varies regionally. The 1990 amendments of the Clean Air Act of 1963 (CAA) require that emissions of sulfur be restricted and rolled back in two stages by the year 2000. There have been a number of reports expressing concern about the future of the industry in the states where high sulfur coal is produced. The remedies devised by the federal government and many coal-producing states in the past to "se-cure" the future of the regional coal industries have focused on the physical task of removing sulfur rather than the economic challenge of doing so at a cost that will enable high-sulfur coals to survive and compete. The past remedies, generally, were not specific enough to account for the characteristics of regional coal deposits and did not look at the coal market as an integrated national and international entity. The State of Illinois has, in recent years, taken a more comprehensive approach to the solution of the problem.

Jan 1, 1992

By M. Irish, M. Jahraus

Accurate prediction of gold (or other metal) production from a heap leach operation is essential to the economic vitality of any such operation. However, this is also one of the most challenging issues facing managers of these facilities. Three approaches to modeling gold production from the Valley Leach Facility (VLF) at Anglogold’s Cripple Creek & Victor Gold Mining Company are presented. Evolution of these modeling methods has been necessary as ore heights and volumes have increased. In addition, the complex geometry of the VLF presents additional complications to production modeling, Comparison of actual and predicted gold production are presented

Jan 1, 2001

By R. Zunich, E. Rybinski, M. Grondin, B. Flintoff

It is uncommon these days to read a business magazine or newspaper without finding a reference to Knowledge Management (KM), and its critical importance to corporate success. One definition of KM is: “getting the right knowledge to the right people at the right time and helping them to put information into action in such ways that strive to improve organizational performance.” In the minerals processing industry we could assert that we have been practicing this for years through effective operator training. In most cases we would probably be wrong. Training has certainly filled the need of addressing safety and basic operational issues, but we must collectively focus on education (learning), and the difference, as measured in outcomes, is not at all subtle. This paper briefly examines the history of training and education in the mining industry, and looks in more detail at the impact of one company’s approach to empower its workforce, while keeping the ultimate goal clearly in mind: “The great end of knowledge is not knowledge, but action.” (T.H. Huxley)

Jan 1, 2001