Search Documents

By Steven I. Majtenyi

INTRODUCTION The heavy risk inherent in all underground construction projects contributes significantly to the high cost of transportation tunnels. First, the knowledge of this risk leads the engineer to design conservatively. Second, the cost overruns are still common with a high proportion of them originating from corrective measures needed when unforeseen problems develop during excavation. These unforeseen problems includes - encountering unexpected objects, materials and water conditions - experiencing an unforeseen behavior of the materials - damaging property beyond the expected range of influence of the tunnel construction. To minimize these expenses, more emphasis is being placed on well planned and interpreted site investigation programs in the final design and planning stages of the project. It is well known that the cost of a planned excavation is less than the cost of dealing with the same conditions when they are encountered unexpectedly. Therefore, the objective of site investigation is to provide a complete set of reliable data for designers and contractors that is continuous along the projected tunnel alignment. Two alternatives axe available to achieve this objective; - for shallow tunnels, it is often feasible to generate continuous data by drilling appropriately spaced, vertical bore holes and applying sensing techniques for interpolation (1, 8). - for deep tunnels, or certain urban tunnels under existing structures, closely spaced, vertical bore holes are not feasible except for narrow zones at the portals. In such cases direct horizontal penetration may be required that may be complemented by radial sensing to extend the range of information.

Jan 1, 1976

By Sarah Holtz Wilson, Kenneth Rossi, Carl R. Handford, David F. Tsztoo

The East Bay Municipal Utility District’s Claremont Tunnel is an 18,000-foot long water tunnel that crosses the Hayward Fault zone near Oakland, California. It was originally completed in 1929. This project involved the construction of a bypass tunnel through the fault zone, including an enlarged vault section designed to accommodate up to 8.5 feet of horizontal offset. Ground conditions encountered included sheared and crushed serpentinite and clayey fault gouge, and presented specific challenges for construction. A special excavation and support sequence used concrete-backfilled side drifts as foundations for the vault steel sets. It also allowed for a 20-foot-wide top heading and bench excavation in soft and squeezing ground conditions.

Jan 1, 2007

By Leon Maday, Dan L. Pecha, Jeremy Johnson, Daniel N. Adams

The Brightwater conveyance system includes 26 km of tunnels, a 130 mgd pump station, 2 km of micro tunnels, and a 2.4 km outfall. The tunnels extend from Woodinville to Puget Sound through varying soils in 1 to 7 bars of hydrostatic pressure and depths to 185 m. The tunnel diameters range from 4 to 6 m and include numerous lining systems. This paper highlights major shaft and tunnel design, including dual cellshafts, multiple pipe configuration tunnels, polymer concrete segments, and the use of a one pass lining designed to convey high pressure effluent.

Jan 1, 2005

By R. R. Rollins

Conventional methods of controlling abandoned mine fires include: loading out, inundation, fire barriers, flushing, and surface sealing. This paper describes a proposed fire-control technique utilizing a new explosive fragmentation method. An impervious barrier is created by using explosive energy and strategic emplacement in boreholes drilled from the surface. Blast round design, average fragment size, and impermeability of the fragmentation barrier are discussed. This barrier, created by the blasted floor rock, could also be used to fill in the open space in abandoned mines for subsidence prevention or control.

Jan 1, 1989

By Jack E. Fraley, Robert E. Simpson

INTRODUCTION Spokane Mining Research Center (BuMines) is researching sealants for underground coal mines to: 1. Reduce sloughing of shale roofs. 2. Reduce sloughing of coal ribs. 3. Seal block stoppings against air losses. 4. Construct stoppings by spraying over jute cloth or metal lath. 5. Render incombustible in-place polyurethane foam. Originally the work was directed towards reducing sloughing of shale roofs. Many underground coal mines have shale directly over the coal which weathers severely after exposure to the mine atmosphere. Lab investigations(l, 2, 3, 4) have shown that many shales separate into layers when immersed in water or stored in a high relative humidity environment. Upon drying or after removal from high humidity, the shales continue to separate. Underground coal mines become wet in the warmer months from condensation of the ventilating air. Conversely, the mines become dry in the cooler months from evaporation. The mines experience severe shale break-up during the summer and much less break-up during the winter. Figs. 1, 2 and 3 show weathered shale roofs. in underground coal mines. Fig. 4 shows fallen shale on the entry floor. Sealing the shale reduces this sloughing problem.

Jan 1, 1974

By S. Tuylu, D. Adiguzel, A. Bascetin, H. Eker

"Tailings can be more stable in-site where they are stored and and so the risk of conventional tailings dam accidents can be reduced by alternative methods. In recent years, surface paste disposal (SPD) method is one of the alternative tailings storage methods. According to the results obtained from the previous lab scale experiments, optimum storage design was determined and then, this design was carried out in-site application under atmospheric conditions by a pilot scale tests. In the field study, two separate dams with no environmental hazards were established by the hazardous waste storage directive, whose surface area is measured as 400cm × 200cm. Also physical changes in the paste tailings were measured by the sensors such as volumetric water content, mutric suction and oxygen consumption. In addition, seepage water was collected in the drainage pool and examined for acid mine drainage and metal mobilization risks. As a result of the preliminary data obtained from measurements of pilot scale tests, when the pH value of seepage in the cemented dam (only 1th and 10th layers with cemented) is about 11, the pH value of seepage in the uncemented (reference) dam is measured at 8-9. INTRODUCTION Environmental damages occurred during the deposition of mine process tailings at surface using conventional methods (tailings dam etc.) can be reduced and/or eliminated with the use of new technologies and methods to an important extent. Nowadays, it has been investigated to safely deposit metal mine wastes generally discharged into surface tailings dams, seas, rivers, creeks etc. using Paste Tailing Technology which gains the growing importance in recent years. Meanwhile, Paste Tailings Technology has two applications in industry as an underground paste backfill and surface paste deposition. Particularly scientific studies about deposition of process tailings as paste sample in underground and surface have been increased. These studies showed that surface paste deposition can minimize the free water amount which is the biggest problem in conventional tailings dams. Additionally, it also provides less particle segregation, in other words, the formation of more homogenous material, the development of geotechnical properties which causes to obtain more stable material, increases the strength and stability of the paste with addition of binder where necessary surface paste material, and reduces the risk of Acid Mine Drainage (AMD) (Bascetin et al., 2017a). Theriault et al. (2003), Martin et al. (2006) and Simms et al. (2007) reported that Bulyanhulu mine in Tanzania is the first gold mine to employ surface paste disposal (SPD) worldwide. Here, tailings are deposited alternately via several towers. The tailings flow away from each tower to forming a conical deposit. Each layer had a lower thickness than 30 cm. The fresh tailings were poured on top of drying and hardening layer after a waiting period of 5-30 days. No cement was added into the tailings to prepare paste material. Uncemented paste was deposited by a solid content of 73% which corresponded to a 250 mm slump cone height (Yilmaz et al., 2014). In a study conducted by Yilmaz (2010) illustrates the preliminary results of a field cell testing undertaken to investigate the effect of in situ climate conditions and material properties on the performance and quality of fine-grained, sulphide-rich paste tailings at the LaRonde mine in Quebec, Canada. A total of two field cells are constructed in the surface disposal site of the mine and categorized as cemented cell CC and uncemented cell UC (Bascetin et al., 2017b)."

Jan 1, 2018

By Paul Eger

The use of wetlands to treat mine drainage has become increasingly common, particularly as more information is available on their operation and construction. However, the lifetime of each system is still, at best, an estimate. Treatment lifetime depends on the types of processes that provide the majority of the metal removal. Anaerobic systems (vertical flow systems) rely primarily on sulfate reducing bacteria, which reduce sulfate to sulfide and generate alkalinity. Metals can be precipitated as sulfides, and acidity is neutralized. These systems can remove over 90% of the metals and increase pH from around 4 to over 7. The bacteria will remain active as long as the system remains anaerobic and contains an adequate supply of sulfate and small chain organics. Although estimates of lifetime made on the total carbon in the system suggest that lifetime should exceed 20 years, data from field and laboratory studies show that the rate of sulfate reaction decreases with time, and that after several years rates decreased substantially. To maintain acceptable treatment, either additional organic material must be added or the total metal and acid load to the system would need to be reduced substantially. Aerobic systems (overland flow wetlands) can effectively remove metals from neutral mine drainage by reactions with organic material in the substrate. Over 90% of the copper and nickel have been removed in aerobic systems treating mine drainage in Minnesota. The primary removal processes in these systems include adsorption, ion exchange and complexation, which are finite; removal will cease unless new removal sites are generated. Two wetlands built in Minnesota have been successfully treating mine drainage for 12 years. At one of the wetlands, the annual production of new removal sites has been estimated to be equal to the annual metal input, and, as a result, metal removal should theoretically continue indefinitely.

Jan 1, 2005

By R. A. Pimentel

Complying with reduced dust standards (i.e., less than 2.0 mg/m3) due to quartz levels that exceed 5 percent is presently a critical problem for many continuous mining sections. Results are presented of research which was performed to determine the factors causing high levels of respirable quartz dust and to identify the major contributors to operator exposure. It was found that the significant sources of quartz dust are the drilling of the roof and the mining of the roof, floor and rock bands. Both the miner and the bolter may be on a reduced standard, but compliance is easiest to achieve on the bolter for which improvements in maintenance and operator practices are usually sufficient. At the miner, the problem is more elusive. Research continues to identify operating and mining practices that contribute to the exposure..

Jan 1, 1985

By R. R. Klimpel

The process of froth flotation as a means of upgrading the quality of coal by removing ash/pyrite and of separating selected mineral(s) from undesired gangue materials is certainly one of the most common unit engineering operations in use today. Flotation has been successfully practiced at the industrial scale for well over 50 years, and if anything, its use is increasing due to the ever decreasing feed grades of the coals and minerals being processed. Flotation, as a process, has also shown itself to be an extremely flexible process that lends itself well to a wide variety of solid/solid separations. Thus separations can involve very different particle sizes, particle densities, relative weight ratios of materials to be separated, etc., with surprisingly little modification in equipment and operating philosophy required.

Jan 1, 1988

By Fred N. Kissell, Robert J. Timko

Safe escape from coal mine fires continues to be a concern of the mining industry. The most life-threatening fires occur outby the working sections. Because stoppings always leak some air, an outby fire may in time cause intake escapeways to become contaminated with smoke and toxic gases. Smoke and gas infiltration into intake escapeways can be minimized by raising their air pressure over that of adjacent airways. This can be done by checking off the intake escapeway near the working face. The Bureau of Mines has investigated the use of a parachute stopping as a quick-erect check curtain during mine fires, and the concept has been tested in several mines. In every instance, when a parachute stopping was erected on the section, the intake pressure went up substantially. The pressure-raising effect of the parachute persisted for up to 1200 m (4000 ft) outby. Results indicate that checking off the intake escapeway may serve as a viable way to improve safety during mine fires.

Jan 1, 1991

By Kevin Andrews, Zach Agioutantis

Analysis of Coal Pillar Stability (ACPS) software, released in 2018, integrates numerous empirical pillar design techniques. The ACPS program incorporates methodologies originally available as design tools from the National Institute for Occupational Safety & Health (NIOSH), including Analysis of Longwall Pillar Stability (ALPS), Analysis of Retreat Mining Pillar Stability (ARMPS), Analysis of Multiple Seam Stability (AMSS), and concepts including Coal Mine Roof Rating (CMRR), the Mark-Bieniawski pillar formula, and pressure arch loading. The design methodologies that are the basis of ACPS were developed via analysis of significant amounts of real-world data and have been standards of the United States coal industry for decades. While there are empirical factors built into ACPS, making it ideal for use in U.S. coalfields, the concepts in the program have proven to be applicable in variable mine settings, and the software was developed to allow for user-based, site-specific modifications of key design inputs. Application of ACPS to cases outside the regions for which it was developed must be approached carefully, and continuous development of site-specific data is mandatory. A case study is presented involving the application of ACPS to assess pillar stability and assist future design for an underground lignite mine in Eastern Europe. Assessment of in-mine observations, review of the geology of the lignite mine, and evaluation of specific conditions associated with a failure event resulted in “calibration” of key input factors to ACPS. Scenarios evaluated with ACPS suggest that pillar strength and overburden depth are key factors for the determination of pillar stability and design in future areas.

Jun 25, 2024

By W. M. Shaver, W. R. Dengler, F. A. Edwards

INTRODUCTION The Macassa Division of Lac Minerals Ltd. is a high grade gold mine that has been operating in Kirkland Lake, Ontario for the past 51 years. It produces approximately 120,000 tonnes of ore per year, averaging approximately 18.7 grams per tonne (0.45 ounzes per ton) of gold. Over the years, the ore body has been developed to a point where mining takes place below the 1,220 m (4,000 feet) elevation and 1,830 m (6,000 feet) west of the original shaft. The mine is currently serviced by two surface and two winze shafts. (Figure 1). The ore body extends below the 1,930 m (6,400 feet) Level which is the bottom of the existing mining operation. An ambitious underground exploration program has substantially increased these reserves. Concurrent with the discovery of greater reserves, has been rapidly escalating mining costs, particularly labour which constituted 66% of the total cost in 1981. These costs continued to escalate as the major proportion of mining was carried out to the west, far away from the existing hoisting systems. This required three lift hoisting for men, materials and ore. I n addition to the increased travel time and ore handling expense, increased humidity and temperature and ventilation and compressed air losses have added to the inefficiency of the operations. As a result, studies were initiated in 1980 to assess the future of the Macassa operation.

Jan 1, 1985

By Jeffrey B. Smith

Introduction The gas shortage is going to be with us for some time to come. If we can set aside political and industry rhetoric (along with subjective personal opinions), we still are confronted by two serious "facts of life": (1) for almost a decade the U.S. has been con¬suming natural gas at a greater rate than we have been finding new reserves; and (2) there is a finite amount of natural gas present within the earth&apos;s crust. Much of the known and easily exploitable sources of gas (the so-called "conventional" sources, such as the high permeability sand reservoirs of the Tertiary sequence along the Gulf Coast) already have been developed; their production is declining rapidly. The total producible reserves from con¬ventional gas reservoirs amount to only 216 Tcf, less than an 11-year supply. However, several large potential resources of natural gas remain to be developed. These "uncon¬ventional sources" have low permeability and/or peculiar producing characteristics. The DOE program for development of these unconventional sources of gas is called the enhanced gas recovery (EGR) program. The primary goal of this program is to provide a data base of resource characterization and production technology that will lead to commercial development. DOE will encourage and support in¬dustry participation in developing and demonstrating technologies needed to reach this goal. Unconventional Resources Four major unconventional resources of gas have a high potential for commercial development. There are other unconventional sources (such as gas hydrates) that are too poorly defined to warrant a major development thrust at this time. The four unconventional sources of gas currently included in the EGR program are: 1. The carbonaceous shales of Devonian age in the Appalachian, Illinois, and Michigan sedimentary basins are the targets of the Eastern Gas Shales Project (EGSP). 2. The low permeability, low porosity so-called "tight" gas sandstones of the Upper Cretaceous/Lower Tertiary in the Rocky Mountain areas constitute the resource target for the Western Gas Sands Project (WGSP). 3. The free methane trapped in coal beds of both the eastern and western U. S. constitute the Methane from Coal Beds Project (MCBP). 4. The abnormally high pressured, high-temperature saltwater aquifers of the Texas¬Louisiana gulf coast are targets of the Geopressured Aquifer Project (GPAP). Basic implementation strategy for these EGR projects involve (1) assessing and characterizing the resource potential of the resource; (2) conducting cost-shared field testing with industry to improve, develop, and demonstrate various stimulation and production technologies; (3) coordinating EGR activities within DOE and with other federal agencies (such as the Bureau of Mines) to minimize duplication; and (4) aiming all projects toward commercial development of the gas resources. EGSP What type of "geological animal" is the EGSP dealing with? While gas undeniably is related to the occurrence of natural fracture systems within the shale, the overall producing mechanism and precise location of fractured, gas¬bearing locales within each basin is still poorly understood. By developing reliable resource characterization techniques and applying effective stimulation technologies we intend to elevate the Devonian shale from the status of a potential gas resource to that of a proven gas reserve. Once we have done this the private sector can take over the large-scale commercial development of the Devonian shale gas resource. WGSP The second largest project (both in terms of complexity and level of funding) is the WGSP. The primary targets for this project are the low permeability (< 1 md) gas sandstones of the Piceance, Uintah, and Greater Green River basins and the Northern Great Plains Province. Project success in these four primary geologic locales will permit investigating additional low permeability sandstones in 16 other sedimentary basins. It ap¬pears that the only practical means of increasing permeability and resultant flow rates from these sandstones lies in the use of massive hydraulic fracturing techniques. Unfortunately, it is still too early to design such jobs with predictable results. MCBP The MCBP is to be involved in producing and utilizing methane derived from coal beds. The coal, like portions of the Devonian shale, is impermeable, highly fractured (termed "cleat" by

Jan 1, 1980

By L. Alan Weakly

Coal mines and power plants utilize different methods to control dust for the safety of their workers and to protect their installations. The methods that they use are limited by the Environmental Protection Agency or the states in which they operate. Now there is a new technology for controlling dust at conveyor transfers! The Passive Enclosure Dust Control System utilizes several proven technologies to mitigate fugitive dust. This new system has been proven to be four times more effective than standard enclosures utilizing bag house collection and is considerably less expensive to install and operate.

Jan 1, 2000

By Jeffrey B. Smith

Introduction The gas shortage is going to be with us for some time to come. If we can set aside political and industry rhetoric (along with subjective personal opinions), we still are confronted by two serious "facts of life": (1) for almost a decade the U.S. has been consuming natural gas at a greater rate than we have been finding new reserves; and (2) there is a finite amount of natural gas present within the earth&apos;s crust. Much of the known and easily exploitable sources of gas (the so-called "conventional" sources, such as the high permeability sand reservoirs of the Tertiary sequence along the Gulf Coast) already have been developed; their production is declining rapidly. The total producible reserves from conventional gas reservoirs amount to only 216 Tcf, less than an 11-year supply. However, several large potential resources of natural gas remain to be developed. These "unconventional sources" have low permeability and/or peculiar producing characteristics. The DOE program for development of these unconventional sources of gas is called the enhanced gas recovery (EGR) program. The primary goal of this program is to provide a data base of resource characterization and production technology that will lead to commercial development. DOE will encourage and support industry participation in developing and demonstrating technologies needed to reach this goal. Unconventional Resources Four major unconventional resources of gas have a high potential for commercial development. There are other unconventional sources (such as gas hydrates) that are too poorly defined to warrant a major development thrust at this time. The four unconventional sources of gas currently included in the EGR program are: 1. The carbonaceous shales of Devonian age in the Appalachian, Illinois, and Michigan sedimentary basins are the targets of the Eastern Gas Shales Project (EGSP). 2. The low permeability, low porosity so-called "tight" gas sandstones of the Upper Cretaceous/Lower Tertiary in the Rocky Mountain areas constitute the resource target for the Western Gas Sands Project (WGSP). 3. The free methane trapped in coal beds of both the eastern and western U. S. constitute the Methane from Coal Beds Project (MCBP). 4. The abnormally high pressured, high-temperature saltwater aquifers of the Texas-Louisiana gulf coast are targets of the Geopressured Aquifer Project (GPAP). Basic implementation strategy for these EGR projects involve (1) assessing and characterizing the resource potential of the resource; (2) conducting cost-shared field testing with industry to improve, develop, and demonstrate various stimulation and production technologies; (3) coordinating EGR activities within DOE and with other federal agencies (such as the Bureau of Mines) to minimize duplication; and (4) aiming all projects toward commercial development of the gas resources. EGSP What type of "geological animal" is the EGSP dealing with? While gas undeniably is related to the occurrence of natural fracture systems within the shale, the overall producing mechanism and precise location of fractured, gas-bearing locales within each basin is still poorly understood. By developing reliable resource characterization techniques and applying effective stimulation technologies we intend to elevate the Devonian shale from the status of a potential gas resource to that of a proven gas reserve. Once we have done this the private sector can take over the large-scale commercial development of the Devonian shale gas resource. WGSP The second largest project (both in terms of complexity and level of funding) is the WGSP. The primary targets for this project are the low permeability (< 1 md) gas sandstones of the Piceance, Uintah, and Greater Green River basins and the Northern Great Plains Province. Project success in these four primary geologic locales will permit investigating additional low permeability sandstones in 16 other sedimentary basins. It appears that the only practical means of increasing permeability and resultant flow rates from these sandstones lies in the use of massive hydraulic fracturing techniques. Unfortunately, it is still too early to design such jobs with predictable results. MCBP The MCBP is to be involved in producing and utilizing methane derived from coal beds. The coal, like portions of the Devonian shale, is impermeable, highly fractured (termed "cleat" by

Jan 9, 1980

By E. G. Hoover

In the mid-I 970s the rallying cry sent out by the aggregate trade associations to aggregate operators was to come to Washington and help design national legislation mandating reclamation of pits and quarries. This collective effort paid off in that aggregate operators were able to assist in the design of "livable" legislation; however, the coal mining industry took some very hard hits. A principal argument used by the aggregate industry was that relatively small parcels of land are impacted, the operations are located in or near urban areas to serve in the development of that immediate area, and are of many years duration; whereas, coal strip mines disturb many acres, are of short duration, and whose products may have world or nationwide utilization. Historically, developments in reclamation are tied closely to the regulatory systems that have been created to control environmental effects of mining. Since reclamation generally results in a cost incurred after the stone, sand and gravel has been mined and does not add to the inherent value of the mineral, there was little incentive in the past for mine operators to reclaim the land. In 1977, the Surface Mining Control and Reclamation Act (SMCRA) became the law for coal mine operators. The law states that, among other provisions, reclamation must "restore the land affected to a condition capable of supporting the uses which it was capable of supporting prior to any mining, or higher or better uses". It is of interest to note that years before the initiation of legislation leading to SMCRA twenty-eight states already had reclamation regulations that covered virtually all minerals. The scope of performance standards found in the state reclamation regulations included slope stabilization, grading, revegetation, neutralization of toxic materials, visual screening, waste disposal, control of drainage, and other sources of pollution and erosion. Environmental legislation and the consequent regulations came about because the public perceived that private industry did not properly value environmental quality and as a result the government became the policeman.

Jan 1, 1998

By Scott G. Britton

Today&apos;s coal mines are turning more and more to belt haulage as the key system to transport coal out of the mine. The advantages of using belt for both intermediate and main haulage are numerous. Belts are reliable high capacity haulage mediums that can be utilized at low operating costs. They are adaptable to rolls in the coal seam and can handle relatively steep grades. They are not noisy, operate with a minimum amount of labor, and are easily extended and retracted. Belts require the least power of any haulage medium, are easily controlled by push- buttons and interlocks, and present low fire and safety hazards. Belt haulage can also be the largest source of operational problems for mine management when not installed correctly. This chapter and Chap. 6 concentrate on proper installation of both the static and dynamic components of efficient belt haulage. This chapter looks at the static system component, composed of the belt drive, its installation and operation, as well as belt takeup and transfer point construction. These components do not change readily over the life of the installation, hence the term static system. Chap. 6 discusses the dynamic system of belt line construction, which includes belt splicing, breaking down and reanchoring the tailpiece, and extending the belt line, plus operational and maintenance items for belt operation. This chapter is divided into three major topics. The first is a general discussion covering the points necessary for designing an efficient haulage system; the second looks at installing belt drives, head rollers, and takeups, and the third discussion centers on installing efficient and effective transfer points along the haulage system. Each will address the design and construction issues facing the engineer or construction supervisor in charge of installing the system. Before looking at the static system, it may be useful to review some of the basic design factors and considerations of all belt haulage systems. The material usually carried on an underground belt is a mixture of raw coal and rock, commonly known as run-of-mine (ROM) coal. This mixture has certain material characteristics that guide the mining engineer to the final and proper belt selection. The characteristics looked at most frequently are: 1) Angle of Repose is the angle at which the material will freely make a pile. Most ROM coal averages a 35"-39" angle of repose. 2) Angle of Surcharge is the angle a pile will assume on a moving conveyor. This ranges from 5" to 15" less than the angle of repose in most materials. For ROM coals, 25" is the average angle of surcharge. 3) Flowability, which determines the maxi- mum cross-sectional area needed to carry any given material on a belt. It is measured by the angles of repose and surcharge of a material and also serves as an index of the safe incline angle for the belt line. These characteristics, plus practical engineering research and development work are defined by an organization called the Conveyor Equipment Manufacturers Association (CEMA) for most bulk materials. CEMA also provides a code for each classified material depending on the characteristics above and the subjective considerations of the average size to be encountered, the abrasiveness of the material, and any miscellaneous characteristics (oil resistive, corrosive, etc.) which may be important. For coal, CEMA (composed of member companies in-

Jan 1, 1983

By U. Paschedag, H. Bussmann

"Bucyrus manufactures the most comprehensive product portfolio of mining equipment worldwide. Its mission is to have a positive, lasting effect on our world. Bucyrus makes sustainable development a fundamental way of doing business through economic, environmental and social initiatives that support, educate and benefit our employees, customers, shareholders and other stakeholders. Our participation in GRI (Global Reporting Initiative), a network-based organization that has pioneered the most popular sustainability reporting framework will be discussed as well as examples will be given on each major field of engagement. Two examples from surface machinery are most fuel efficient haul trucks as well as the Highwall mining system which allows access to coal reserves which are lost not making use of this kind of system. Two examples from underground machinery are Bucyrus’ automated plow systems for the mining of medium and thin coal seams with minimum rock and Bucyrus’ intelligent CST drive system for high-powered armored face conveyors (AFCs) for efficient use of energy."

Jan 1, 2011

By Snehamoy Chatterjee, Dharmasai Eshwar, Aref Majdara, Rennie Kaunda, HUGH MILLER

The U.S. mining industry has made progress in reducing accidents and injuries, but interpreting safety data remains difficult due to changes in workforce size and productivity. The Mine Safety and Health Administration (MSHA) uses tools like the pattern of violation (POV) and significant & substantial (S&S) calculator to monitor safety, though these have limitations. To address this, we developed an information entropybased risk (IER) index that combines various safety metrics, including citations, penalties and injuries. Using data from 2011 to 2020, the IER index was validated with statistical methods and clustering algorithms to ensure it accurately reflects risk levels. The analysis showed clear differences in risk across mining sites, proving the index’s usefulness. The IER index was then applied to a coal mine to demonstrate its effectiveness. This new tool can help mining companies better assess their safety risks and take action to improve workplace safety.

Nov 1, 2024

By J. Tuzson, H. McL. Clark

Introduction Wear of pumps, wet cyclones and pipelines by suspended solid particles will impact their operating economies by limiting their useful life, reducing their reliability and increasing the amount of servicing. Erosion is considered a materials problem. The empirical solution consists of testing different materials in field applications. Such tests are time consuming and expensive. The prediction of localized wear rates, life estimates and appropriate material selection demand a better understanding of the slurry wear process in environments corresponding to those found in working equipment. Key words: Wear, Slurry abrasion, Coriolis erosion tester The slurry wear process Solid particles suspended in liquid generally move with the flow, but such particles deviate under the centrifugal and Coriolis forces encountered in pumps. The concentration of particles will increase, and a solid layer or bed may accumulate if the acceleration is directed against the flow passage wall. Large particles in dilute suspensions may impact the wall. dissipating their kinetic energies and removing material. However, particles smaller than about 11)(1 µm encounter great drag when moving through the liquid. and such par¬ticles have little kinetic energy left when they reach the wall. They cannot penetrate the stagnant boundary layers present in pumps. Therefore, small particles tend to form beds that slide along the wall, removing material by a process that could he called sliding erosion or wet abrasion. Wear by impact erosion from large particles in dilute slurries can he predicted by appropriate analytical and empirical methods. However, laboratory tests and calculations of wear rates that correspond to sliding erosion are more likely to correlate with field experience from wear under similar conditions. Specific energy Data from laboratory slurry erosion experiments have shown that the amount of material removed is approximately in proportion to the energy expended in the erosion process. Thus. the specific energy-energy expended in removing by erosion a unit volume of material-offers a simple, practical measure for the erosion resistance of materials. The concept was found to also apply to sliding erosion (Clark et al.. 1997). Generally, the study of the material-removal process in slurry erosion continues to remain a subject of research. Conceptually, if the flow velocities and accelerations could be calculated in a pump or pipeline, the energy dissipated at the passage walls could also be estimated, and the material removal rate would become known from the specific energy determined by laboratory tests. Slurry erosion testing Laboratory devices made specifically for slurry erosion testing may be grouped into the following: jet erosion devices, slurry pots and the Coriolis test machine (Pagalthivarthi and Helmly, 1992). Jet erosion devices use a slurry pump and nozzle to produce a high-velocity slurry jet that is directed at a flat material specimen, either perpendicularly or at some acute angle. Combined impact and sliding erosion are produced. but the processes cannot be separated, and the wear is difficult to assess except by weighing. Slurry pots consist of a cylindrical vessel containing the slurry of interest. In the slurry pot, test specimens are attached to a rotating arm. The samples are rotated in the slurry and experience local flow conditions that result in combined impact and sliding erosion. Wear depth measurements from detailed laboratory experiments have been successfully correlated with results from an analytical model of the process, and specific energy values have been calculated (Wong and Clark, 1995). In industrial use, the samples are weighed to determine the total material loss. Materials are ranked with respect to some reference material. The Coriolis erosion tester (Tuzson, 1984) consists of a rotor with a central cavity, from which two opposing radial passages lead out (Fig. 1). The slurry is fed to the centerof the rotor in one pass from a stirred overhead tank. The slurry particles are subjected to the Coriolis acceleration as they flow out through the radial passages. The material specimens are mounted into the radial passage walls facing the direction of rotation and are eroded by the particles that are pressed against them as they flow out radially. A narrow groove is worn into the sample within a few minutes, using a few gallons of slurry. Material removal is estimated accurately from profilometer traverses across the wear scar at different locations. The energy dissipated by the particles can be estimated, which leads to a well-defined experimental value for the specific energy.

Jan 1, 2000