Search Documents

By P. Tsang

The stability of longwall chain pillars depends not only on the mechanical properties of coal and surrounding rocks, but also geological and mining conditions. In order to evaluate the effects of each, variable, the orthogonal experiment design was employed in this study for significance analysis. The study concluded that the stability of longwall chain pillars is mainly controlled by the ratio of pillar stress to pillar strength, the ratio of Young's moduluds of the roof to coal and floor to coal, entry width, pillar width and the internal friction angle of coal. Additionally, horizontal stress, panel width and mining height also play a significant role.

Jan 1, 1994

By B. J. Arnold

Froth removal rate is perhaps the most important parameter in scaling up from laboratory tests to plant froth flotation circuits. The WEMCO froth factor, the percentage of the froth height over the lip of the cell, accounts for the difference between laboratory and plant froth removal rates. As laboratory tests are generally run with a high pulp level, laboratory results are directly comparable to plant results only when a high froth factor (high pulp level) is run in the plant. When a plant does not have a high pulp level, laboratory results must be modified by using a ratio between laboratory and plant kinetics to predict plant results. This ratio, which accounts for the froth factor is important in testing any new reagents or reagent dosage levels. CQ Inc. researchers have used predictive scale-up equations using this froth factor coupled with equations for kinetics and the residence time distribution in the froth flotation cells. These equations show that modifying the froth factor in the plant can have a large impact on flotation cell yield and reagent use. EQUATIONS DESCRIBING FROTH FLOTATION Scaling up from laboratory- to plant-scale coal froth flotation has been the subject of much research and debate over the years. Determining the proper rate equation to describe flotation kinetics and an equation to describe the residence time distribution in a bank of flotation cells have been particular areas of study. As shown in Tables 1 and 2, various rate equations and residence time distribution equations have been proposed in the literature. These equations consist of one or two parameters giving the rate constant(s) in units of time-1 and a parameter for recovery at infinite time, [Roo]. Dowling, Klimpel, and Aplan (1985) evaluated the rate equations in Table 1 for their ability to fit froth flotation kinetic data and found that all of the equations give reasonably low standard errors. Several of these equations, however, proved to have superior confidence limits for the parameters. Other equations have also been proposed to describe the recovery versus time profile. Most recently, Diao et al. (1992) proposed a first-order form with a sine wave distribution. As indicated in Table 2, investigators have suggested many equations to describe the residence time distribution in continuous froth flotation. To measure the water residence time distribution in a bank of cells, a soluble tracer is often used, with the level of tracer being measured over time at the tailings discharge. This response is then put on a dimensionless basis as described by Austin et al. (1984) in order to compare mixing behavior between cells or under different conditions. Coal flotation cells are generally of the flow-through or hog-trough variety allowing for some degree of backmixing and short-circuiting. While the water residence time distribution (see Figure 1) at the end of one cell in a bank of 1.4 cu ft WEMCO froth flotation cells may approximate perfect mixing conditions (Arnold, 1989), the water residence time distribution at the end of a bank of cells does not. Figure 2 shows the RTD for various flotation cell types compared to that for perfect mixers in series. To better describe the water residence time distribution in coal froth flotation cells, Van Orden (1986) used an equation similar to the perfect-mixers-in-aeries equation. This

Jan 1, 1993

By O. A. Bascur

Current competitive demands on the process industries stimulate the need for improved operating efficiencies and compliance to stricter governmental regulations. Emerging information technologies allow narrowing the gap between management business objectives and the process control level. Benefits come from enhanced energy management, operating costs reduction, enhanced scheduling of activities, reduced quality giveaway, enhanced market driven production and enhanced decision making. Plant management systems integrate economic performance monitoring by controlling the business rather than just throughput and product quality. Sound business based decisions about how to operate the plant can be achieved by adequate dynamic performance monitoring at the plant level and the enforcement of the desired targets at the process control level. This paper describes some of the key requirements to implement a process management system to meet stricter process performance standards. Extensions are made to facilitate conforming with regulations established by various governmental and industry monitoring agencies.

Jan 1, 1993

By Charles Stone, Eric Wang

A method for estimating geotechnical rock loads for shallow cut and cover subway stations is presented. Localized geotechnical conditions lead to extreme variations in rock loading on the walls of subway structures. Actual lateral rock stress on these structures can range from near zero to over four times the vertical in-situ rock stress. The primary factors affecting the actual lateral stress are intact and rock mass mechanical properties, excavation sequence, localized tectonic conditions, and potential future adjacent structures. The authors recommend using the AASHTO code value of 65 pounds per cubic foot (10 kN/m3) during concept design, followed by numerical analysis of rock wedges and stress measurement for final design.

Dec 1, 2022

By Raphael G. Kazmann

The predicted warming of the earth's surface, presently the subject of much debate, controversy and legislation, is based on what is termed "the greenhouse effect." This is the result of the property of certain atmospheric gases. These gases allow the passage of radiant energy to the earth's surface and reflect back, to the earth, the infrared radiation given out by the heated surface. Physicists have computed that if there were no greenhouse effect the average temperature of the earth, now about 15° C (60T), would be close to -18° C (OT). Just what gases have produced this salubrious effect? Water vapor is the most important. Then come carbon dioxide, methane and a number of minor constituents of the atmosphere, both natural and man-made. Climate change, its cause and its impact on human activities have been the subject of scientific and historical study for more than a century. Recently, some scientists have concluded that if the man-made increase in the carbon dioxide and other greenhouse gases continues, by the late 21st century the earth's global average temperature will rise between 2° to 8° F. This temperature rise would cause the water in the oceans to expand and the massive polar glaciers to melt. In 1980, it was predicted that the sea level would rise 7.6 m (25 ft) by the late 21st century. By 1985, the predicted rise was 1 m (3 ft); and by 1989, it was 0.3 m (1 ft) (Jastrow, Nierenberg and Seitz, 1990). Agricultural scientists have pointed out that an increase in atmospheric carbon dioxide would enhance biological growth including the production of foodstuffs.

Jan 1, 1992

By R. Mathur

Cu isotope fractionation in low temperature aqueous environments has been well documented. Here we apply Cu isotopes to two distinct, yet related mining problems. First, an exploration geological application where we measured copper isotope fractionation in oxidized leach caps, chalcocite enrichment blankets and hypogene mineralization in 4 porphyry copper deposits located in South western USA. Cu isotope patterns exist in the lateral and vertical distribution within the mines coupled with distinct relationships with Cu grade. Second, a hydrometallurgical application where we measured the leach fluids, feed and residues from a quick leach text of Cañariaco ores. The results indicate the relative proportions of the minerals providing Cu during leaching. Interpretations of the QLT test measurements indicate covellite is the dominant ore mineral providing Cu during leaching. Both applications clearly demonstrate the power and ability of using the Cu isotope technique to understand low temperature aqueous processed involving copper.

Jan 1, 2010

By M. J. Laurila

On-line analyzers have made possible the use of Fuzzy Logic Control (FLC) for local control applications in coal preparation plants. This includes FLC control of complete circuits such as heavy media vessels, cyclones and froth flotation. These circuits can be controlled in real time in a feedback control loop with an on-line analyzer. Control strategies can be readily developed using Statistical Process Control (SPC) techniques which are first applied off-line in manual mode through the use of control charts and then this process is brought on-line using FLC in conjunction with an on-line analyzer to fully automate the circuit. This paper outlines the types of control strategies employed and presents examples of automatic verses manual control.

Jan 1, 1997

By Francesco Chiappalone, Tanner Murt, Lance Waddell, Cristina Oñate Salazar

The 3RPORT project is a 5-mile-long, 16-foot-internal-diameter tunnel excavated in hard rock by Slurry TBM in Fort Wayne, Indiana. Two-component grouting can be separated into two core areas of operation: batching and underground operations. This paper addresses the challenges faced and solutions implemented in these fundamental areas. The effects of external factors and their impacts on mix design and batching of grout will be explored. Underground, challenges of monitoring parameters and ensuring a proper mix between the two-components will be discussed, focusing on the adopted technical solutions and considerations to be taken in the design stage of tailskin grout ports.

Jun 13, 2021

By Aidan Giblett

"It is important to make a clear distinction on the scope of work of the Global Mining Standards and Guidelines (GMSG) guideline for sampling grinding circuits. Many mineral processing practitioners are familiar with the sampling and surveying of comminution circuits, in particular grinding circuits, for performance diagnosis and the identification of optimization potential. These surveys often provide information for population balance modelling of individual comminution and classification unit processes, and consequently require a large amount of information to calibrate and validate the unit models. As a result, these surveys are labour intensive, somewhat expensive, depending on internal capabilities of the mine site or company and have a long time span from initial planning to final reporting. They also require a high level of expertise to process the survey data, simulate the circuit and make sensible recommendations on follow up actions.As a result of these factors, full grinding circuit surveys are not a common occurrence at a large number of processing facilities, and several years may pass before follow up surveys are conducted. In the ensuing gap between surveys, the efficiency of the grinding circuit must often be taken on faith, and this is considered an unacceptable lapse in an environment of strained natural resources and low commodity prices.To support the rapid and productive energy efficiency analysis being promoted by the ICE working group, a much simplified survey and analysis process is required. The process reflected in the GMSG guideline is indeed more conducive to frequent analysis, at a skill level that is well within the capabilities of the average plant metallurgist. As a result, it becomes feasible to conduct mini-surveys of plant performance, which can be used to quickly and precisely diagnose the high level impact of process changes. These methods can also be manipulated by an experienced practitioner to provide sufficient information for modelling of the circuit to estimate the impact of process changes, allowing an initial rate and rank exercise to focus plant optimization efforts."

Jan 1, 2015

By Dale E. Hirschfeld

The clays in Eastern Washington occur in a variety of forms and are extracted for uses in Face Brick, paper coatings, and aggregates. Not in large volumes in comparison to other areas, not even from impressive large mines. However, mans utilization of these clays has progressed from historical clay tablets to the present technically oriented manufactured products of today. White Face Brick, perhaps the whitest produced anywhere is the unique product produced by INTERPACE CORPORATION's Mica Plant from these unusual clays. It is this basic characteristic feature of the clay's in the Mica area that differentiate them from the other clay's in this belt. ORIGIN The significant properties of clay's used in Face Brick are plasticity, fired color, fired strength, dry and fired shrinkage, the PCE or Pyrometeric Cone Equivalent, and extrudability. Testing clay's for these properties is standard laboratory procedure. No two clays are alike, and seldom can one clay be substituted for another. Mica White Clays respond favorable to all these properties, but more especially, the Mica Clays fire to a brilliant white color, from almost the natural state. The geologic history of Eastern Washington is largely conjectural because of the absence of rocks representing segments of geologic time. The oldest rocks in this area are the argillaceous and arenaceous sedimentary rocks which have been slightly metamorphosed. These rocks have been correlated with the Belt Series of the Pre-Cambrian age, although some may be older. These rocks were subsequently intruded by granadiorites and related rocks that are considered to

Jan 1, 1971

By M. L. Klohn

The Felder ore deposit is a 5,000,000-pound uranium deposit in the South Texas Coastal Plain. It occurs in the basal sand of an Oakville Formation (Miocene) alluvial system. The host sand is a carbonate-rich arkose which contains virtually no carbonaceous debris and has been reduced by the local introduction of hydrogen sulfide. The ore lies well within the reduced zone and occurs as coffinite and uraninite that fill interstices and coat and replace grains. The overall geometric configuration of the ore is that of a winged, crescentic ore roll. Weak mineralization extends the wings of the ore roll and gives greater expression to the roll character. Departures from the shape are controlled by discontinuities in bed- ding and by proximity of the ore to the surface. Associated with the uranium is a broad halo of anomalous molybdenum. Subsidiary mineralized trends suggest a pre-existing up-dip position for the main roll. Oxidation from the surface largely destroyed this previous roll by solubilization of uranium. Uranium subsequently migrated into favorably reduced sand and reprecipitated at the present roll position.

Jan 1, 1970

"The Industrial Comminution Efficiency (ICE) working group, part of the Global Mining Standards and Guidelines Group (GMSG) has engaged a large number of industry professionals representing mining companies, equipment vendors, consultants and metallurgical laboratories with interests and capabilities in the comminution field. These participants have collaborated to develop three guidelines for the assessment of the efficiency of mineral comminution circuits. Two of these guidelines deal specifically with power based modelling techniques to quantify energy efficiency using widely practiced techniques, those developed by Bond (1961), Rowland and McIvor (2009), and Morrell (2009). The third guideline deals with the sampling and surveying of grinding circuits as is required to provide the necessary information, at appropriate quality, to furnish the efficiency analysis promoted by the first two guidelines. This preprint will focus on the Guideline on Methods to Survey and Sample Grinding Circuits, which is currently in the final stages of peer review and finalization by the GMSG. INTRODUCTION It is important to make a clear distinction on the scope of work of the GMSG guideline for sampling grinding circuits. Many mineral processing practitioners are familiar with the sampling and surveying of comminution circuits, in particular grinding circuits, for performance diagnosis and the identification of optimization potential. These surveys often provide information for population balance modelling of individual comminution and classification unit processes, and as a result require a large amount of information to calibrate and validate the unit models. As a result these surveys are labour intensive, somewhat expensive depending on internal capabilities of the mine site or company, and have a long time span from initial planning to final reporting. They also require a high level of expertise to process the survey data, simulate the circuit and make sensible recommendations on follow up actions. As a result of these factors full grinding circuit surveys are not a common occurrence at a large number of facilities, and several years may pass before follow up surveys are conducted. In the ensuing gap between surveys, the efficiency of the grinding circuit must often be taken on faith, and this is considered an unacceptable lapse in an environment of strained natural resources and low commodity prices. To support the rapid and productive energy efficiency analysis being promoted by the ICE working group, a much simplified survey and analysis process is required. The process reflected in the GMSG guideline is indeed more conducive to frequent analysis, at a skill level that is well within the capabilities of the average plant metallurgist. As a result it becomes feasible to conduct mini-surveys of plant performance, which can be used to quickly and precisely diagnose the high level impact of process changes. It can also be manipulated by experienced practitioner to provide sufficient information for modelling of the circuit to estimate the impact of process changes, supporting an initial rate and rank exercise to focus plant optimization efforts."

Jan 1, 2016

By P. Lan

Gold is often associated with arsenopyrite in many refractory gold ores. The selective recovery of arsenopyrite by flotation is therefore necessary in order to maximize the recovery of gold. However, the complexity of arsenopyrite flotation often makes it difficult to obtain a high recovery from real lean gold ore. This paper presents the results of arsenopyrite flotation by ultrasonic pretreatment in micro flotation experiments and bench scale flotation tests. The tests showed that pure arsenopyrite exhibited low natural floatability due to the oxidation on the mineral surface under ambient conditions. Using ultrasonic pretreatment, the oxidation film was ruptured and the floatability was enhanced greatly. The presence of Fe (III) was found to inhibit the flotation of arsenopyrite and this depression was also removed by the ultrasonic pretreatment. This result explained why the arsenopyrite in real ore is often difficult to float and how ultrasonic pretreatment can effectively improve the arsenopyrite flotation in real gold ores. Guanidine (GMM) was found to be a superior collector for arsenopyrite in acidic medium and xanthate in alkaline medium.

Jan 1, 1998

By Stig Eriksson

In Switzerland two major railway systems as shown below in Figure 1 has recently been completed or is under construction: ¦Lötschberg, south of Bern which was commissioned in 2007 ¦Gotthard, south of Zurich which is scheduled to be commissioned in 2016The aim is to increase the transport capacity of the railway system and to transfer more transport of goods to the railway by offering transport of trailers and lorries on the new railway systems. It will have a positive environmental impact but also improve the congested traffic situation of the highways in north-south directionThe Gotthard tunnel is totally 57 km (35 mile) long and the Lötschberg tunnel is 35 km (22 mile) long. Both tunnel systems consist of two parallel single track tunnels connected with cross tunnels at every 333 m (1 093 ft). Additionally there are cross-over tunnels and caverns for installations and operation. In the Lötschberg tunnel, the majority of the excavation has been by Drill & Blast and in Gotthard tunnel the major part is being excavated by TBM.

By V. T. McLemore

The Wind Mountain (WM) nepheline syenite deposit is part of the alkalic complex in the Cornudas Mountains, which ranges in age from 34.6 ± 1.5 Ma to 36.8 ± 0.6 Ma. The WM deposit consists of a complex, zoned pluton that ranges from syenite porphyry to nepheline syenite porphyry. The WM deposit has potential use for ceramics and dark-colored beverage containers and consists of nepheline, k-feldspar, albite, and varying amounts of other minerals. Analcime also is present locally but must be avoided because it is unsuitable for ceramic and glass. Chemically the deposit consists of 56-63 % SiO2 17-21 % Al2O3 and 4.0-5 % Fe2O3. Although initially iron is high, when the crushed rock is passed through a specialized magnetic separator, the iron content drops to below commercial maximum standards of less than 0.5% Fe2O3. The WM deposit is currently under exploration and testing to determine marketability.

Jan 1, 1994

By Graham A. Mathieson

The precise definition of an ultimate or economic pit has, over the years, received much attention in the literature on the subject of mine planning. Unfortunately, relatively little has been published in the area of pit sequencing and scheduling--an aspect which is typically of much greater economic significance both during the life of a mining operation, as well as in the evaluation of an exploration project. This paper discusses an overall mine planning methodology with emphasis on the design of an optimal sequence of pit expansions or phases. Although the concepts given are not new, it is hoped that some practical suggestions will be made. The paper will also describe graphical techniques which have been found useful in comparing the merits and impacts of alternate planning strategies and production schedules.

Jan 1, 1982

By R. J. Sweigard

One possible alternative for disposal of flue gas desulfurization (FGD) by-products is use as backfilling support material in highwall mine adits. The finite element method was used to analyze the variation of stresses and displacements within and around a highwall adit backfilled with FGD materials. The engineering properties of the rock material and the optimum mix proportioning of the FGD materials were obtained from laboratory tests. Finite element analyses show that, for the case in question, the roof displacement would decrease about 48 percent and the peak stress could be decreased about 58 percent. The study indicates that fairly weak FGD materials can eventually lead to stability of backfilled highwall adits.

Jan 1, 1996

By Kaye P. Strong, Desmond M. Levins, Anthony G. Fane

1. INTRODUCTION The safe disposal of tailings is the most important environmental question facing the uranium mining industry today. This is because tailings present a major long term radiological hazard as they contain about 71% of the radioactivity originally in the ore. The magnitude of the problem can be appreciated by considering the quantity of tailings involved. For example, projections of milling programs in Australia indicate that there will be 100 million tonnes of tailings produced by the year 2000 (Levins 1980). The United States currently has in excess of 100 million tonnes and by the year 2000 will have between 900 and 1700 million tonnes (Landa 1980). Present options for tailings rehabilitation include leaving them above ground, returning them to the mine or placing them in specially excavated pits. In any event, the tailings will be covered with earth and revegetation attempted. This will remove the problems of airborne radioactive dust and water erosion of the tailings, at least in the short term, but diffusion of radon-222* from the tailings may still occur. The Atomic Energy Control Board of Canada (1981) has proposed a maximum allowable radon flux from rehabilitated tailings of 0.074-0.37 Bq m -2s-1(2-10 pCi M-2 s-1); the exact level is to be determined "after discussion with other regulatory agencies and the industry". The United States Nuclear Regulatory Commission (USNRC 1980) has been more restrictive in recommending a maximum flux of 0.074 Bq m -2s-1 (2 pCi m-2s-1). As a guideline they also suggested a minimum depth of covering material of 3 m to achieve this surface flux for tailings typically found in the western milling regions of the United States. The design of rehabilitation schemes is aided by a knowledge of radon transport through tailings piles. In this paper we present the results of a theoretical analysis and experimental study of radon diffusion through selected Australian tailings and cover material. The minimum cover criteria of 3 m is reexamined in the light of these findings. [ ]

Jan 1, 1981

By S. Mafi

The Broken Aro project is associated with a 1910 abandoned underground mine complex that has been discharging aeid mine drainage from entries, seeps and springs. The Ohio Department of Natural Resources(ODNR), R&F Coal Company (R&F) and American Electric Power (AEP) are involved with this unique project that will remine the abandoned underground complex and install a mine seal constructed of fixated flue gas desulfurization (FGD) material. The goal of the project is to eliminate or reduce the acid mine drainage that is discharging into the watershed. This paper discusses remining, installation of the FGD mine seal, government financed reclamation projects and future application to active and abandoned mining sites.

Jan 1, 1998

By J. S. Hall

The productivity and fuel efficiency of iron-ore blast furnace operations has greatly increased in recent times. These improvements, particularly to the Japanese steel industry, have primarily arisen from process engineering studies of the blast furnace and associated operations such as sintering. The development of fluxed sinter based on iron-ore fines reacted to produce highly reducible, low slag sinters has contributed further to a reduction in fuel requirements. The Pilbara province of Western Australia is a significant source of these iron-ore fines supplied to the international market. Increasingly, this market is being offered high quality ores from other foreign sources. To technically assist companies in improving the processing efficiency of ores, and to improve the technical marketing of ores by modelling the processing characteristics of Australian/international ore blends, the Commonwealth Scientific and Industrial Research Organization (CSIRO) is actively assisting the industry by researching the general theme of 'iron ore from mine to metal in this paper we outline progress towards a numerical description of: a. ore deposit classification. b. Degradation during transport. c. Direct reduction of iron ore. d. Liquid bath ore reduction/smelting. e. Industrial sintering.

Jan 1, 1986