Search Documents

By R. Brändle, R. Luis-Fonseca, R. Cornejo, G. Fischer, G. Von Rickenbach, J. Jarufe

Rock damage around underground excavations has been an important hazard in mines and tunnels. Rock dilation generates buckling that needs to be contained before it causes damage to equipment or safety concerns to mine workers. In seismically active mines, rockburst occurrence has been widely recognized as one of the most important hazards in deep mines and tunnels. While there is a wide range of cases where rockburst hazard can be mitigated through dedicated excavation sequences, reentry procedures or exclusion zones, there are still many situations where large unexpected rockbursting may occur, relying only on rock support as the last mitigation measure to prevent production and safety losses. Considering the previous situations, surface support as mesh, plays a major role containing the failed/ejected rock and providing a safe working environment to the underground operations. While there have been considerable achievements in improving mesh resistance, with more than 26Kj/m2 of energy dissipation capacity, there is still a lack of research in the overlapping mechanism and load transfer between contiguous mesh elements. This paper presents the state of the art in static and dynamic analysis of welded and rolled mesh overlaps, based on experimentation carried on by Geobrugg in their Research Center, leaving clearly established that the difference in meshes is not only in levels of energy absorption, but also concluding that in the case of high resistance rolled meshes overlapping is not necessary and the transmission of stresses can be fully guaranteed by using suitable connecting elements. All these characteristics, supported by operational advantages as light weight and mechanized mesh installation, provides a considerable improvement in safety and productivity, improving the economic value of the project

Apr 26, 2022

By Mahesh C. Jha, Frank J. Smit

Column flotation and selective agglomeration are promising advanced physical cleaning processes that can be developed for preparing premium quality coal-water slurry fuel from coal fines. Such a fuel could either replace oil or natural gas in certain industrial and utility boilers or else could be burned in advanced combustors currently under development. These applications require coal cleaned to sulfur and ash contents below 258 g/GJ and 430 - 860 g/GJ (0.6 lb/million Btu and 1 - 2 lb/million Btu), respectively, to meet clean air emission requirements. A highly loaded slurry must be produced in order to avoid derating the boilers, and the total cost of the fuel must be below $2.37/GJ ($2.50/million Btu) in order to penetrate the market by the turn of the century. Achieving these technical and economic goals depend critically on the selection of suitable feed coals. This paper describes the identification and evaluation of 18 coals and final selection of six coals from different regions of the United States as potential feedstock for preparation of premium fuel. The work is being performed under a cost-shared DOE project.

Jan 1, 1995

By G. W. Luxbacher

Coal mine infrastructure is rarely designed solely on the basis of ventilating the underground workings. Instead the optimization of a mining sequence, the minimization of coal quality variation, reduction of coal losses by adapting to property boundaries and geologic structure (seam inclination, roof conditions, coal thickness, etc.) or other similar considerations have formed the objective for mine plant design and layout. Infrastructure development may also reflect a desire to maximize production early in the life of the mine or to permit flexibility in mining according to market conditions. Requirements for coal mine ventilation, established by the 1969 Coal Mine Health and Safety Act, have mandated changes in the traditional concepts of mine plant design in the United States. Mines, in operation prior to the passage of the Act have experienced severe limitations when attempting to adapt the existing mine infrastructure to meet the requirements of the law. In addition the increased quantities of air required, velocity limitations on trolley haulage and belt lines, the establishment of separate intake escapeways and gob area ventilation have com- pounded the inherent complexity in planning mine ventilation systems. Past practices in mine ventilation planning and design are no longer adequate. Given the complexity of today's ventilation systems, effective planning and design approaches are required. As such, the interrelationship between the overall coal mine plant design and ventilation system design is examined. An approach to ventilation system design constrained by global considerations of mine plant design, is presented. The proposed approach is, however, applicable to the design of new mine ventilation systems as well as to the modification of existing systems.

Jan 1, 1980

By F. J. Susko

The Bureau of Mines investigated rapid bubble-pulp separation to improve flotation kinetics. A shallow-depth froth separator was employed to quickly recover the mineral-laden bubbles from a mixture of ore, water, and air bubbles. The shallow depth minimized the rising distance required to recover even the smallest size bubbles (100 ~m). Therefore, the slurry remained in the unit only long enough to recover the bubbles before the pulp exited through the conical bottom. Joining this unit with a rapid bubble-particle attachment unit, a rapid flotation system was formed that floated silica from phosphate in one-fifth of the retention time for conventional mechanical cells. The hydrodynamics of the rapid flotation system along with fundamental parameters for scale-up are presented in this paper.

Jan 1, 1992

By Sidney L. Hansen

This report was written because of concerns of the possible error involved when stopping leakage is incorrectly assumed to be turbulent. It is common practice to use turbulent flow to characterize each airway branch for computer models of mine ventilation circuits. This report addresses computer methods to accurately model air-leakage paths. A graphical method is described for deriving the equations of leakage through stoppings. The significance of modeling leakage according to the proper flow regime (turbulent or laminar) is demonstrated by the following method. A hypothetical mine was developed to represent present-day conditions. The stoppings of the mine were chosen to leak according to laminar flow properties. The mine was represented by constructing two base models. One base model used turbulent leakage equations for each stopping, while allowing the corresponding resistances to vary. The other base model used the correct laminar leakage equations and held corresponding resistances constant. The mine circuit was then expanded to demonstrate future development. The expanded portion was designed with stoppings that were identical to those in the base mine. The mine in the future state was represented by two projection models. Each projection model was an extended version of its associated base model; one used turbulent leakage equations and one used laminar leakage equations for stoppings. The laminar projection was theoretically correct and is used as a basis for comparison of differences in airflow quantities. Rather than modeling every leakage path for stoppings, a more practical approach is also discussed. A good level of accuracy is maintained by combining leakage paths if the proper flow equations are used. This method was used on the hypothetical mine projection and the flows were very similar to the theoretical values.

Jan 1, 1989

By Arpad E. Torma

The introduction of biotechnological principles in hydrometallurgy has created new opportunities and challenges for the industry of mineral processing. During the 1950's and 608s, the mining wastes and unused complex mineral resources have been successfully treated in bacterial assisted heap and dump leaching processes, especially for the production of copper and uranium. The economic viability of bio- leaching technology lead to its world-wide acceptance by the mining industries. During the 1970's this technology grew into a more structured discipline which is called "biohydrometallurgy". Currently, bioleaching techniques are ready to be used, in addition to copper and uranium, for the extraction of cobalt, nickel, zinc, gold and silver from diverse mineral resources and for the desulfurization of certain coals. However, in a foreseeable future the biohydrometallurgical processes may be applied also for the treatment of high- grade ores and mineral concentrates using native and/or genetically engineered microorganisms.

Jan 1, 1989

The 23rd annual American Mining Hall of Fame Awards Banquet sponsored by the Mining Foundation of the Southwest will be held at the Tucson Marriott University Park Hotel, Tucson, AZ on Saturday, Dec. 3, 2005. The Mining Foundation of the Southwest is a non-profit organization. It educates the public about the mineral industries and reports outstanding accomplishments in the fields of mining and the earth sciences. This year’s inductee, guest of honor and featured speaker at the banquet will be Pierre Lassonde, president of Newmont Mining and resident of the World Gold Council. He is one of Canada’s leading gold analysts.

Jan 1, 2005

By None None

Use this month wisely — go online and take advantage of your new member benefit. As an SME member, you can read and download for free all of the full-text papers of the Mining, Metallurgy & Exploration (MME) journal, including the 22 papers in the launch Special Issue on Mineral and Metallurgical Processing in Honor of Professor Emeritus Douglas W. Fuerstenau as well as the archived articles of Minerals & Metallurgical Processing (MMP), all the way back to Vol. 1, No. 1. Just follow the instructions on this page.

By E. M. Schern

The Morenci/Metcalf porphyry copper mining operation, located in southeastern Arizona, currently processes approximately 100,000 tons of ore per day and has copper ore reserves estimated to be in excess of one billion tons. Functional groups within the Geology Depart¬ment (currently staffed with six professional and two support personnel) include mine geology, project geology, and hydrogeology. The primary task of mine geologists is daily preblast bench face mapping with grade and mill amenability estimates. Auxiliary duties include detailed in-pit metal distribution evaluation, mineragraphic work and flux quarry geology. Project geologists conduct explora¬tion and preliminary development projects both within and outside the Morenci district and provide support to ore reserve block modeling and geotechnical work performed by the Morenci mine engineering group. Hydrogeologists handle exploration for and development of groundwater' resources and groundwater flow modeling, mine dump leach solution penetration and recovery evaluation, and tailing dam water reclamation.

Jan 1, 1983

By R. N. Tempel, M. Lengke

Arsenic sulfide (orpiment, realgar, amorphous AsS and As2S3) oxidation rates were measured in mixed flow reactors at pH-2 and at temperatures of 25 ° to 30 °C. The measured oxidation rates for arsenic sulfide solids by dissolved oxygen are in the range of 10-11 to 10-10 mole m-2s-1 after being normalized to final surface area. The order of arsenic sulfide oxidation rates decreases at pH-2 from amorphous AsS > realgar > orpiment > amorphous As2S3. Compared to pyrite, arsenic sulfide oxidation rates are approximately 1.5 to 15 times slower than pyrite oxidation rates at pH-2.

Jan 1, 2003

By D. R. Nagaraj

There are few organic ligands that can adsorb effectively on noble metals, especially gold, in aqueous media. Ligands containing sulfur and nitrogen donors are known to be the most effective. Dithiophosphorous acids, for example, are known to adsorb on gold under certain conditions and these, along with xanthates, are used traditionally to recover gold values by flotation from ores. These compounds, however, are not necessarily selective for gold since most of the associated sulfide minerals are also floated. Monothiophosphorous acids, on the other hand, were recently discovered to float gold values selectively from sulfide-containing ores in a mildly alkaline medium; thus the dicresyl monothiophosphate is now used commercially in a gold flotation operation in the U.S.

Jan 1, 1991

By J. M. Wempen

As development in underground coal mines progresses away from the critical components of the ventilation system, including the main fans and ventilation shafts, resistance within the system is markedly increased. This results in higher pressure and flow requirements from the main fan(s) to maintain adequate face ventilation. Upgrades to the primary ventilation system are often required. The use of booster fans underground is a potentially practical alternative to the addition of shafts and surface fans. This study presents simulations of the use of booster fans in two underground ventilation scenarios, one longwall and one room-and-pillar. The booster fan effects on the power requirements of the ventilation systems are evaluated.

Jan 1, 2011

By Y. Topkaya, R. E. Johnson, B. R. Palmer, Bruce E. Kurtz, Anatoli Omelian, John I. Choi

This paper relates to hydrometallurgical studies on the recovery of soluble aluminum values from aluminum-bearing ores, i.e., Georgia clays. At least 50% of the soluble alumina values were recovered by leaching the calcined clays from aqueous solutions, comprising simultaneously contacting a stream containing an effective amount of a reducing agent such as sulfur dioxide and a stream containing an effective amount of an oxidizing agent such as chlorine gas for a time sufficient to dissolve alumina. The recovery of alumina from this aqueous slurry of the calcined clay by leaching with sulfur dioxide and chlorine gas showed much better results than that by leaching with concentrated sulfuric acid and/or concentrated hydrochloric acid at 100O C. The leaching reactions between the aqueous slurry of the calcined clay, chlorine gas, and sulfur dioxide were strong exothermic reactions for several hours, requiring no external heating.

Jan 1, 1993

By Kumar Vikram

Rich reserve of prime quality limestone in east khasi hills of India and abundant quantity of low-cost fuel (Natural Gas) in Bangladesh made Lafarge Surma cement limited a joint venture company of Lafarge France and Cementos Molins Spain to envisage an integrated cement plant at Chatak District-Sylhet) a bordering town of Bangladesh. Since April 2006 the single flight 17 km Long Belt Conveyor (LBC) built by M/S Larsen & Toubro Ltd. (L&T), ECC Division an engineering and construction company of India, is feeding limestone/shale to the Lafarge Surma cement plant. This engineering marvel was created on a turnkey basis with technology support of M/S Aumund France

Jan 1, 2008

By D. Kaja

The Symons Cone Crusher was invented by Edgar B. Symons in 1923. It was quickly accepted as a superior secondary and tertiary crusher. Nordberg manufactured crushers for the Symons Brothers Co. and in 1928 acquired the Symons Cone business. Since then, the Symons cone has become the standard of the Mining Industry. This is due to the basic rugged design and Nordberg's continued efforts to modernize and upgrade the crusher design over the years. In 1930, the Heavy Duty model was introduced with a 225 kW (300 HP) rating. Then in 1931 the Short Head version was developed to handle finer crushing applications. In 1950, the 7 Ft. XHD design was produced which provided higher crushing force capabilities for harder ores and for smaller product size requirements. Finally, in 1978, the 7 Ft Super Heavy Duty design was created to expand the power rating to 500 HP and to further increase the crushing force limits. The first 7 Ft. Super Heavy Duty crushers were delivered to Bougainville Copper Ltd. in 1978 for the production of primary ball mill feed in a three stage crushing plant with the third stage in closed circuit. The product size was 80% minus 6.35 mm (1/4 in).

Jan 1, 1998

By R. J. Caine

Like most major firms engaged in project management, Dravo Corporation faces a constant challenge to keep its management systems in tune with the ever-increasing demands imposed by larger and more complex projects. This paper suggests that one of the key elements in meeting this challenge is more effective organization of project data. It reveals some of the details of a program at Dravo's Minerals 6 Metals Division which seeks, through better organization of project data, to improve Dravo's capabilities in estimating, cost control, scheduling, performance reporting and material control. In particular, this paper discusses ideas Dravo is developing for improved job numbering, codes of accounts, requisition and purchase order numbering, inventory cataloging, and employee/badge numbering.

Jan 1, 1980

By R. H. Clarke

"INTRODUCTION Characterization of waste rock is frequently an oversight in mine planning which can contribute to significant delay in permitting and ultimately development. Thorough waste rock characterization is now a prerequisite to developing operating and closure plans acceptable to regulators and the public. BACKGROUND A long history of mine development has placed virtually all focus on the economic extraction and beneficiation of ore materials, while waste rock characterization and management received substantially less attention and consideration. Inadequate waste rock characterization has contributed to planning and management practices that are having unintended and unforeseen impacts to surface and groundwater, and in some cases lead to significant long term closure liability. In response, the regulatory community has developed guidelines for performing waste rock characterization during the pre- mine permitting process that in some cases seem onerous (BLM, 2013). Additionally, where a project proponent has not met these guidelines or results have been deemed “inadequate”, the Nevada Division of Environmental Protection and Bureau of Land Management (regulatory agencies) will only issue operating permits with rigid management practices to address the uncertainty, including requirements for lining waste rock facilities. WASTE ROCK CHARACTERIZATION FOR NEVADA PROJECTS Newmont Mining Corporation (Newmont) operations in Nevada approaches waste rock characterization like ore characterization, as it requires a similar investment of time, funding and attention to detail in order to pass public and regulatory scrutiny. Newmont follows a tiered approach to characterization that creates three over-lapping data sets representing an “escalation” in analysis at each tier, an approach that has thus far gained regulatory approval. “Tier 1” waste rock characterization for most Newmont projects begins with exploration drilling which follows internal standards and procedures. 20-foot composite samples are prepared from all drilling and analyzed for multiple trace elements using inductively coupled plasma mass spectrometry (ICP-MS) methods and for acid-base characterization using method ASTM-E1915. If the exploration program is successful and further resource or reserve development is recommended, the Tier 1 data are used to prepare a Waste Rock Characterization Plan (Plan) that will be presented to regulatory agencies as a part of baseline project characterization."

Jan 1, 2015

By Martin H. Stanczyk

In recent, years the demand and consumption of finely ground industrial minerals has substantially increased for such uses as fillers and chemically reactive components. The size, specifications for these types of industrial mineral materials vary to a great extent and depend on the particular end purpose' and on the physical properties of the mineral itself. Size reduction of industrial minerals usually is obtained by conventional crushing and grinding methods. However, some specialized milling techniques have been developed for producing these minerals in extremely fine particle size ranges. During recent years the Bureau of Mines has been investigating an attrition grinding method to produce ultrafine subsieve-size mineral particles. The Bureau developed process, which has been patented,2 comprises the intense agitation of a slurry composed of the material to be ground, a relatively fine granular grinding medium, and a suspending fluid. The process has been shown to be effective for the comminution of kaolin in the particle size range of 2 microns and finer on a batch3 and continuous basis.4,5 This report presents the results of batch tests made to determine the effectiveness of the attrition grinding process for comminuting commercial products of (1) mica, a tough lamellar material, (2) fluorite, a brittle intermediately hard material, and (3) barite, a relatively soft, massive material.

Jan 1, 1967

By Dale W. Norris, John A. L. Campbell

INTRODUCTION Optimization, as measured by productivity gains, is being achieved in our nation's preparation plants principally by automation, economy of scale, and reducing maintenance. Increased tonnage per unit of investment, a1 so a measure of optimization, is being achieved by breaking with tradition and increasing plant utilization, while simultaneously improving on equipment re1iabi1ity. Improved qua1ity, another measure of optimization, is being attained through technical innovation. This review will concentrate on state-of-the- art unit operations and processes, and will not discuss emerging new technologies which are covered in detail in other presentations of this symposium. It is recognized that much of what will be discussed in this paper is not unique to the fine coal circuit, but is equally applicable to the entire preparation plant. However, the areas reviewed are the principal means being used today to optimize an existing preparation plant's fine coal circuit. Prior to designing and optimizing a fine coal cleaning circuit, the question that must first be answered is, "Do we even want a fine coal circuit? This is a much more complex question than is readily apparent, as most of you recognize. It can be argued either way. In the final analysis the "bottom line" will hold (Blackmore, 1982). If your sales contract a1 lows it, and the selling price can justify it, you most assuredly want to build a fine coal circuit into your preparation plant. In general today, most new preparation plants do have fine coal cleaning circuits. The purpose of fine coal cleaning has changed with time. Some of the early applications of fine coal cleaning were to prevent stream pollution rather than to prepare a product for market (Merrill a Pennington, 1962). During the 50's, 60's and into the 70's the principal thrust of fine coal cleaning was in metallurgical coal preparation. More recently, the emphasis of the 80's is on steam coal processing. There is no consensus on what is fine coal. Traditionally, fine coal would be anything below 1/4" in size. Because of the advances being made in intermediate coal cleaning processes, i.e. heavy media cyclones and jig cleaning, this discussion will define fine coal as -28 mesh (Aplan, 1987). Figure 1 is a plot of the size ranges of a large number of U.S. bituminous coals. In general the -28 mesh fraction of a bituminous coal will be between 7% and 18% of the ROM feed with reported ranges of 5% to 40% (Aplan, 1987). Consequently, traditional fine coal cleaning is general 1 y involved with a re1 actively mi nor portion of the coal feed. Every effort is taken both in terms of mining and preparation to keep it that way because of the high cost of cleaning fines. The move away from this posture, namely, the techniques to fine grind coal to liberate pyrite is probably the biggest challenge facing fine coal processing today.

Jan 1, 1988

By Peter Greenhalgh, W. Baguley, R. P. Riley

The traditional impeller system for aeration and suspension of slurries, e.g., in bacterial oxidation plants, is the vertical flat blade turbine (VFBT) . This type of impeller is energy-intensive, which results in a heavy-duty design of shaft, gearbox and drive. The VELMIX bio-reactor development programme is designed to evaluate the use of the new generation of hydrofoil impellers which consume less power and thus have poten­tial for capital and operating cost savings as well as being possibly less damaging to the bacteria. The early tests on pyrite oxidation in a 300 litre laboratory pilot tank using the Thiobacillus ferro oxidans bacteria, showed that hydrofoil impellers had superior charc­teristics to the VFBT impeller and to air­ agitated pachucas, with lower energy input. The geometry of the sparge _ring was found to be very important in optimizing the system.

Jan 1, 1990