Search Documents

By V. A. L. Breguncci, A. H. Martins, C. P. Ribeiro Jr.

This work presents experimental results for the recovery of gold present in alkaline cyanide solutions by using the electroelution technique of strong-base anionic polymeric resins IRA 402-CL from Rhom and Haas-Brazil Ltd. loaded with gold. This technique of electroelution of anionic polymeric resins is based on the removal of metal ions adsorbed to the resin, resulting from a potential difference applied between the cathode and anode in an electrolytic cell. The electrolytic cell was composed of an aqueous solution with suitable chemical characteristics and an anionic polymeric resin bed loaded with gold. The resin used in the experiments was loaded using synthetic alkaline gold cyanide solution with 1.0 g/L of gold. The variables studied were electroelution time, cathode current density, distance between cathode and anode and the electrolyte chemical composition. Statistical methods made it possible to establish the optimum conditions that would achieve satisfactory gold recoveries by the electroelution technique. The statistically predicted response for the resin loaded with gold by percolation was 16.5% gold recovery, 2.0 A/m2 cathode current density, 20-mm distance between electrodes and 6.0 hrs electroelution time. For the centrifuging system, the statistically predicted response was 7.41% gold recovery under the following conditions: 0.25 A/m2 cathode current density, 1-mm distance between electrodes, 3.5 hrs electroelution time and 10.9% NaOH in the electrolyte chemical composition.

Jan 1, 2002

By C. St. J. Lowe

Weir Minerals ? Linatex has developed a new approach to the dewatering of fine solids, particularly mine and process plant tailings and wastes. The Weir process, patented in 2009, uses standard process equipment in a standard flow sheet, but applies this approach to materials previously thought to be too fine to be dewatered with this type of equipment. The process can be applied to a wide range of materials, making lower moisture products that can be re-used elsewhere or sent to disposal. It has already been tested successfully on a small scale in Australia on coal fines, zinc mine tailings, red mud, iron ore tails, and copper/gold tailings. The principal factors affecting the solids recovery have been established as: 1. The % solids in the slurry feed to the process ? a higher % solids provides a higher recovery. 2. The particle size of the feed solids ? coarser feeds provide higher recoveries. The key factors affecting the % solids in the dewatered product have been determined to be: 1. The particle size of the dewatered product - coarser materials produce a higher % solids in the dewatered product. 2. The height of the discharge weir on the dewatering screen - a higher discharge weir on the dewatering screen also yields a higher % solids. 3. The angle of the dewatering screen. Setting the screen horizontal increases the travel rate, reduces the bed depth and reduces the % solids in the dewatered product. Back-sloping the screen up to 5° reduces the travel rate and increases the % solids in product. Eight plants ranging in size from 3 t/h to 40 t/h have been sold to a range of customers in China, for coal and iron ore tailings treatment. Australia has one plant, a small unit rated at 30 t/h of sand fines, and has recently completed test work on iron ore tailings for a dewatering plant rated at 135 t/h. Additional tests are under way with clients around Australia, to demonstrate the capabilities of this process on specific applications and to provide confirmation that materials can be processed successfully, before moving on to larger scale tests or full size plants. The advantages of the Weir process include - lower moisture in products, uses proven equipment, lower capital and operating costs, lower maintenance costs, reduced power consumption, compact footprint, can be used in parallel or in series with existing equipment, modular design to facilitate redundancy or expansion, efficient water recovery and simpler water management, reduced cement in backfill mixes, smaller tailings disposal footprint, reduced earthworks requirements, much lower seepage losses, more stable tailings mass, progressive site rehabilitation, reduced impact on local wildlife, reduced risk of dam wall failure, and reduced environmental monitoring and compliance costs.

Feb 23, 2014

By S. K. Sharma

The Bureau of Mines' rapid method of dewatering fine-particulate slurries uses extremely high molecular weight polymers. These polymers form large, strong flocs which can be dewatered by sieving or sedimentation. However, sometimes these flocs deteriorate rapidly if water is not removed immediately. During field tests, clay slurries have been encountered that could have been dewatered economically if it were not for the rapid floc deterioration. A kinetics study was conducted to determine the rate of kaolin-PED floc degradation in which polymer addition, to bring the flocs back to their original condition, was used to determine the extent of floc decay. Results showed that the amount of polymer added, to replace polymer lost by spreading, was less for the lower PEO concentrations. For this clay-polymer system, floc breakage as judged by polymer additions followed first order kinetics. It was also found that the addition of fluoride ion stabilized the kaolin flocs.

Jan 1, 1992

By B. R. Reddy, Y. V. Swamy, B. V. R. Murthy

Chromitiferous overburden containing nickel in oxide form is reduced with CO-CO2-N2 gas mixtures. This converts the nickel oxide to metallic nickel and restricts the iron oxide to the magnetite state to extract the nickel. Reduction experiments were carried out on 500-g samples in a bench-scale vertical reactor. The tests were run to establish the process parameters, including the optimum partial pressure of CO, the reducing gas flow rate, granule size and roasting time. The reduced calcine is then subjected to an ammonia-ammoniacal carbonate leach to extract nickel selectively as its amine complex. More than 90% of the nickel could be extracted with a volumetric CO/(CO+CO2) ratio of 0.57 at 750°C and a roasting time of 90 min. The addition of 2.5% (by weight) charcoal to the granules improved nickel extraction by 11 % to 19%. Nickel leaching efficiency with ammoniacal solution is compared to the bromine-methanol method.

Jan 1, 2000

By R. J. Morrell

The Bureau of Mines, U.S. Department of the Interior, has developed a hardrock cutting concept and incorporated it into an extraction system called the ripper miner. This concept uses a single, wide bit that attacks the rock at a shallow angle and slow speed. Research has demonstrated that the system is capable of excavation rates exceeding those possible with conventional drill-blast and can effectively cut rock too hard for conventional roadheaders or continuous mining machines. It has the additional advantages of low bit wear and dust generation. This highly flexible concept is applicable to both mining and driving development openings and can cut any material from coal to hard rock. A single rip-per miner can perform the functions of a continuous mining machine, a roadheader excavator, and a tunnel boring machine. This paper presents the history of the development of the ripper miner from the initial laboratory tests through the construction and testing of the full-scale, lab prototype. It includes a comparison of the ripper miner to systems currently used from the standpoint of energy efficiencies and operating costs.

Jan 1, 1989

By T. K. McMahon

Formally, a mathematical model could be defined as: A set of equations whose solution will approximate the response of a physical process or system to a set of stimuli which appear as parameters in the equations. The purpose of a mathematical model is to permit the rationalization of experience to proceed by simulation rather than by physical experimentation. In the application of digital computer control to an industrial process, the mathematical model of the process (subsequently called the process model) is needed to calculate the present process performance from the measured variables and to predict the response of the process to a control change. Functionally, the cardinal element in process model development is a concise set of control objectives. These, besides implicitly defining the boundaries of the system to be modeled, will determine the accuracy demanded of the model its nature: dynamic or steady-state, and so forth, The objectives should explicitly define what process efficiencies, production rates, qualities are to lie within the scope of the computer control project, thereby providing a basis for simplifying assumptions in the development of the model. This requirement, a limited set of control objectives, is so often disregarded in formulating industrial control problems that its repetition can scarcely be avoided.

Jan 1, 1965

By S. K. Mishra, S. B. Kanungo

Because conventional (physical) methods of ore dressing are not suitable for reducing the phosphorus contents of high-phosphorous manganese ores from Andhra Pradesh (AP) and the adjoining area in southern Orissa, India, the adoption of chemical methods becomes imperative. An attempt was therefore made to reduce the phosphorus content of partially beneficiated manganese ores from AP by roasting with sodium carbonate and then leaching with hot water. However, due to the higher phosphorus contents of the manganese ores from Nishikhal mines in southern Orissa, and because of their apparent resistance to dephosphorization by roasting with Na2CO3 alone, a mixture of Na2CO3 and NaCl was found to be necessary to reduce the phosphorus content to below 0.15%. Free-energy calculations at 700°C and above indicated that Na2CO3 (or Na2O as the active component) is a more active reagent than NaCl. Various process parameters, such as the temperature and time of roasting, the amount of sodium carbonate and the temperature and time of leaching, were studied to arrive at the optimum conditions for dephosphorization.

Jan 1, 2000

By Robert Cook, Valeria Zarate, Jason Hallowell

The long hole open stoping (LHOS) method is widely used in underground mining. While methods to predict stable stope geometries are well established, the ability to maintain a stable back often assumes effective ground support across the full stope span. The efficacy of the support strategy is dependent on rock jointing, quality, density, top cut width and height, and the type, amount, and orientations of bolts installed. However, it is becoming increasingly common for operators to assume narrow top cuts in service of wider stope spans with minimal bolting coverage. Failure to account for the required top cut drift size and support requirements can ultimately lead to raveling type instabilities along stope shoulders that result in back collapse. A new method has been developed to evaluate the minimum top cut dimension necessary to accommodate wider stope spans with various rock bolting configurations. Due to the economic impacts of top cut development and support, this is a critical consideration in the accurate costing and scheduling of a LHOS operation. Tables 1 lists the acronyms are used throughout this paper.

Feb 1, 2025

By R. Gilliam

The Jewett Mine is located in two East Central Texas Counties, Leon County and Freestone County. The area is primarily suited for agriculture with approximately 90% of its agricultural income coming from beef cattle and hogs. In addition to livestock both of these counties produce hay, oats for grazing, pecans and corn. There are 1,101 farms and/or ranches in Freestone County consisting of 381,248 acres. Less than 15% of this acreage is harvested croplands. Leon County has 1,227 farms and/or ranches for a total of 442,387 acres, of which less than 13% is harvested cropland. Total annual agricultural sales for Leon County are approximately $36 million and Freestone County has approximately $21 million. Ninety percent of the annual agricultural sales derive from livestock.

Jan 1, 1992

By J. Marbeau

In this paper, a geostatistical study of the North Butte roll type uranium deposit is presented. The geostatistical procedure applied takes into account the varying direction of the roll front for reserves calculations. For variogram calculation, the roll front is unfolded thereby allowing estimation of the variogram in directions parallel to and perpendicular to the roll front. Variograms calculated in unfolded space show strong directional anisotropies consistent with the anticipated configuration of the deposit.

Jan 1, 1991

By S. Angioletti

This paper addresses strategic investment decisions when they are nested in a project development format where each project is implemented in phases and each phase is approved to move on to the next phase only if certain technical and economic requirements are met. This configuration is sometimes referred to as a ?Project Portfolio?. Mining companies maintain project portfolios in their exploration investment plan. This study proposes a procedure to best manage an exploration project portfolio including technical and economic uncertainties. The procedure may support decision makers in a simple and intuitive way, while maintaining the rigor and precision required by the rather large amount of financial resources typically called for by mining projects. The procedure was tested in a real case study of a gold mining company and its exploration projects portfolio. The procedure uses the following approaches: i) investment valuation methods under technical and market uncertainties based on Option Pricing Model, Real Option Theory and Option Space; ii) portfolio management and Stage Gate®1 method; iii) Monte Carlo simulation.

Jan 1, 2010

By Samir Kumar Pal, Rajasekar Rathanasamy, Gobinath Velu Kaliyannan, Moganapriya Chinnasamy, Sathish Kumar Palaniappan

The research examines the performance of uncoated and coated tungsten carbide-cobalt rock cutting bits. It aims to optimize process variables (cutting speed, depth, coating material) considering multiple output responses (cutting forces, specific energy, wear rate, material removed, angle of reaction forces). The study uses a hybrid optimization technique combining Taguchi design, grey relational analysis, and fuzzy logic. The optimal parameter combination was found to be cutting speed: 200 mm/s, cutting depth: 6 mm, and titanium aluminum silicon nitride coating.

Apr 24, 2022

By J. D. Pitts

The worldwide production of iron ores was approximately 880 million metric tons in 1975. This level is the result of an annual growth rate of nearly four percent during the period 1967 to the present. The high growth rate was particularly significant in that two relatively severe worldwide recessions occurred in 1971 and 1975. The current upturn in world economic growth will probably allow future annual iron ore production growth rates in excess of the four percent figure, and, in fact, the International Iron and Steel Institute (IISI) has predicted that a five percent rate should be realized through 1985. The IISI figures would indicate a 1.4 billion metric tons per year output by 1985 or an increase in current production levels of around 500 million metric tons per year (MMTA)1. Even the more conservative four percent growth rate prediction from historical data would provide an 2 increase over current figures of nearly 350 MA by 1985. A large portion of world iron ore production is being provided by large resource-rich countries with relatively new industrial bases. These countries are typified by heavy export of raw materials such as iron ore and ore products and a large capital investment in the facilities to recover these raw materials. Brazil and Australia are typical of such countries and, indeed, their production of iron ore in the period 1967 to 1973 increased at annual rates of 17 to 30 percent, respectively, The continual reassessment of resources in these and other major iron ore exporting countries such as Venezuela and Liberia would indicate chat these high growth rates may continue for some years to come to meet anticipated world demand for raw steel production.

Jan 1, 1976

By J. W. Devon

The coal mining industry is divided into two distinct economic segments based on Coal Supply Agreements. Coal supply agreements generally fall into two categories, spot or long-term, with the selected contract term being driven by the buyer's market expectations, security of supply considerations, fuel tonnage and quality requirements, and economics. Short-term or spot coal purchases are generally market driven and are highly competitive in today's marketplace. Long-term contracts, particularly those involving captive mines and mine-mouth power plants, are commonly driven by considerations other than economics. These other considerations, such as Reserve Conservation and Resource Recovery, Security of Supply, and Maintenance of Levelized Costs may increase the cost of coal, often needlessly and without benefit to the buyer or seller. The basic economic principles which guide the market driven metals industry and generally guide the spot coal sector of the coal industry should apply equally well to the long-term coal supply contract. The artificial constraints imposed as a result of regulated rates of return should be re-examined and in most cases, abandoned. There are many methods of surface and underground coal mining being used today such as, open-pit, contour, mountaintop, and area mining for surface mineable reserves; conventional, standard continuous and super-section continuous miners, and longwalls for deep reserves; and highwall miners, thin seam miners and augers in between. This discussion is primarily directed to surface mining, however the same principles of least cost mining on a Net Present Value basis must be considered in all cases.

Jan 1, 1994

By J. B. Griffiths

Clearly there is a tremendous need for assistance in Eastern Europe since most industries must undergo major restructuring. The new governments face many dilemmas, the first task being to establish an order of priorities to deal with the numerous problems at hand. Issues such as the standard of living take low priority compared with market economy and ecological problems. The concept of a Comecon market is now virtually non-existent and trade in roubles ceased from 1991. From this time onwards countries were obliged to trade using free market prices. Governments must also avoid the economic mistakes of countries such as Poland with its high devaluation and lack of economic control and, if possible, contain inflation and unemployment. The privatization of Eastern European enterprises raises considerable difficulties, particularly for large corporations, employing anywhere from 50-100,000 people, which played a major role in the national economy. Whichever method is selected, however, still has to overcome the problem of lack of capital and evaluating the national property. For example, earnings represent only a small percentage of the value of these national industries and thus cannot convert to private ownership without foreign capital investment, either direct or as joint venture capital.

Jan 1, 1992

By Dayu Long, Changhong Li, Yu Wang, Juzhou Li, Yongyue Hu

To address the problem of seepage failure that affects the stability of the fine-grained tailings dam, two kinds of prevention and treatment measures were proposed involving composite flocculants and composite curing agents. The orthogonal test was conducted to determine the optimal ratio flocculant (ORF) and the optimal ratio curing agent (ORCG). Then, numerical models were established to evaluate the effects of the prevention and treatment measures on the seepage and stability of the tailings dam. The results show that the mechanical properties and microstructure of the tailings are significantly improved by adding the ORF and ORCG. Furthermore, numerical studies suggest that the addition of the ORF and the ORCG to the tailings improves the factor of safety of the tailings dam, but the addition of the ORCG also increases the height of the phreatic line. It is also speculated that the addition of the ORF can prevent the formation of through failure zone in the tailings dam. Therefore, the optimal measure to prevent seepage failure in the tailings dam is adding an appropriate amount of the ORF, as it reduces the height of the dam’s phreatic line and lowers the risk of seepage failure. The typical area susceptible to seepage failure can be treated by adding the ORCG. However, it is important to ensure adequate drainage of the area and to maintain the phreatic line at a reasonable buried depth.

Mar 4, 2024

By G. L. Mowrey

One of the critical parameters of any automated coal mining system is the ability to only cut coal and not the rock / waste surrounding it. To do this the system must be able to detect where the coal-rock/ waste interface is. The U.S. Bureau of Mines is investigating a new approach to vibrational coal interface detection (CID) by utilizing an adaptive signal discrimination (ASD) system to perform feature extraction and classification of complex vibrational signals. Accelerometers, geophones, and piezoelectric films are mounted on mining machines and/or strata and are used to monitor vibrations produced during mining operations. Selected data are digitized and the ASD system is trained on known types of vibrations (e.g., "cutting coal" and "starting to cut roof"). A signal classifier is then generated which can be used to identify unknown waveforms. The ASD system can be retrained if mining conditions change significantly.

Jan 1, 1990

An information system (I/S) plan is a means for establishing and communicating the direction the organization intends to take to provide the information required for achievement of organizational goals and objectives. The rapid advancements in information technology, the increasing complexity of systems, and the growing dependence of mining companies on these information systems have emphasized the need for more comprehensive I/S planning. This subsection explores this need, the role I/S planning can play within a mining company, and finally describes a methodology for development of an I/S plan.

Jan 1, 1979

By T. BACHMANN, G. SHAPLAND, E. Amini, N. BEATON, M. BECERRA

In this study, several methodologies to manage low grade and often competent portion of the ore have been proposed and tested in lab, pilot and operational scales. Relevant to this subject, the Cooperative Research Centre for Optimising Resource Extraction (CRC ORE) has developed Grade Engineering® (GE) concept to modify feed streams by rejecting the low grade and possibly hard components in the stream at the early stages of a value chain. Application of GE requires to understand the impact of the process on the value chain as they are value modifiers on in situ opportunities. Traditional modelling approaches and tools do not have the ability to run the analysis in a block model scale with high fidelity in an integrated value chain. Integrated Extraction Simulator (IES) in conjunction with sophisticated analytical tools such as a neural network (NN) was used to develop and reconcile a fully integrated value chain. The value chain model makes it possible to run all available blocks in the Geomet block model, which could be several millions, under possible scenarios for Grade Engineering for economic evaluation analysis and mine planning.

Sep 16, 2020

By L. F. Delgado

Environmental and cost pressures sparked renewed interest in gravity separation. Industrial sands in Mexico are generally processed by screening, desliming, and flotation. Gravity separation with spirals was evaluated as an alternative to flotation in order to lower operating costs and decrease water pollution. Outstanding operating results are obtained in glass and foundry sand operations, plus a more competitive position for Mexican producers due to lower operating costs. Coal fines, generally recovered by flotation, have the same cost and environmental advantages when processed with spirals.

Jan 1, 1994