Search Documents

By A. Jolly, A. R. Kumar, T. Novak

"Coal dust in an underground mining environment has always been a health and safety issue, especially with longwall faces. Efforts to integrate a flooded bed scrubber within a longwall shearer are underway at the University of Kentucky (UK) in order to reduce worker exposure. Small scale physical modeling, along with numerical modeling and full-scale experimentation, are engineering tools being used by the authors for simulating operating conditions underground. Recent advances in affordable 3D printers offer a means for fabricating accurate, scale models for obtaining timely insights prior to building large, expensive test setups. Comparing scale-model results with those of numerical modeling, such as computational fluid dynamics (CFD), lends guidance and confidence in a proposed design. This paper discusses the small scale physical modeling of a longwall shearer with an incorporated flooded-bed dust scrubber in its operating environment. A tracer gas was used in the model in lieu of dust to measure dust-capture efficiency. Results obtained from the physical model are presented and compared with those of CFD model. The small scale model and the CFD results demonstrate good agreement. Dust capture results show the usefulness of the approach in advance of actual design implementation. INTRODUCTION Dust generation is an undesirable, but innate, byproduct of all mining processes. It is particularly problematic in underground coal mining, where coal dust poses potential hazards from two fronts – health and safety. Coal workers’ pneumoconiosis (CWP), commonly referred to as black lung, is a chronic lung disease that results from the long-term overexposure to respirable coal dust. Although the prevalence of CWP has steadily and significantly declined over the three decades following the Federal Coal Mine Health and Safety Act of 1969, a study by the National Institute for Occupational Safety and Health (NIOSH, 2008) indicates that significant health hazards associated with respirable dust still exist within the coal mining industry. In addition to being a health hazard, coal dust can also create a potentially catastrophic safety hazard. Dust that is not captured or removed at its source is suspended and transported throughout a mine by the ventilation airstream. This float dust is subsequently deposited on all mine surfaces along its travel path. Without adequate application of rock dust to these surfaces, forces from a localized methane ignition can reintroduce settled coal dust into the airstream creating an explosive mixture. Therefore, capturing and removing coal dust at its source mitigates the probability of two major hazards that continue to plague the mining industry."

Jan 1, 2016

By H. K. Lin

Elemental sulfur is founded to be the predominant sulfur-containing species in a leaching residue resulting from ferric chloride leaching, under given conditions, of a chalcopyrite concentrate. The mineralogical study of the leaching residue which consists of 52% elemental sulfur reveals that the sulfur formed at the end of leaching process is in the form of discrete crystal rather than coating film. Flotation has been applied to recover the sulfur successfully using xanthate as a collector. Dispersants arc needed to prevent the mechanical entrapment of silicate and quartz by sulfur. Very high recovery of sulfur with satisfactory grades can be achieved with a relatively simple notation scheme.

Jan 1, 1991

By Rudrajit Mitra, Erik Hulthén, TOBIAS HARTMANN, ELISABETH CLAUSEN, Aarti Sörensen

There has been an ongoing debate on how to transform engineering education to better prepare students for today`s professional world that is characterized by increasingly complex problems and challenges that engineers are tasked with upon entering the industry. Within the conceive–design–implement–operate (CDIO) framework, entrepreneurship education presents a valuable pedagogical approach to foster the necessary skills of the students through integrated, hands-on, active learning experiences. While numerous publications have addressed possibilities of how experiential, problem-based, project-based and active learning can be integrated into engineering curriculum, there has been hardly any attention on mining engineering with respect to adopting this approach. This paper will address the possibilities of integrating entrepreneurship education into mining engineering programs in particular. This paper will enhance and foster discussion among academics from mining engineering on how to integrate elements of entrepreneurship education on a course, program and departmental level to infuse value creation experiences across the curriculum.

May 25, 2022

By V. Karra

Based on extensive investigations on the effect of design variables on process performance, during 1982-85, Nordberg developed a 1000 hp cone crusher, with the objective of boosting crushing productivity in existing plants. The 2390 fits on the same foundation as the 7' SHD Symons cone, but is designed to give two times the capacity of the 7'. The economies of scale involved give the customer substantial cost savings. In this paper process performance of the Nordberg 2390 relative to the 7' SHD Symons cone, while crushing the same ore, will be presented. Also, implications of such a crusher scale-up to associated cost savings will be addressed.

Jan 1, 1988

By G. M. Wilemon

The U.S. Bureau of Mines has conducted preliminary investigations on the leaching of phosphate ores obtained from deposits in the western United States using sulfuric acid (H2SO4) in the presence of methanol. Phosphate extractions in excess of 80 pct were obtained on an ore sample from Pocatello, ID. Initial leaching studies using the ore as received yielded extraction levels of approximately 35 pct. However, when the sample was ground for as little as 5 min in a rod mill, in methanol, then treated with HzS04, 82 pct extraction was achieved. The R2O3-P2O5 (R2O3 = Al2O3 + Fe2O3) ratio of the starting material was 0.11. Solubilized products after leaching exhibited an R2O3-P2O5 ratio of 0.02, which is well within desired limits. These results illustrate the potential of acid-alcohol leaching for recovering phosphate values from marginal-grade ores and as an alternative to methods involving current beneficiation techniques that yield lower phosphate recoveries.

Jan 1, 1992

By M. N. Herrera

The bioleaching of mineral sulfide pulps in a bench-scale rotating drum reactor has been studied. The reactor includes horizontal paddles in the inner wall for lifting of the mineral pulp. The performance of the reactor was tested in the bioleaching of a refractory pyritic gold concentrate in the presence of pure Thiobacillus ferrooxidans strain (ATCC 19859). The concentrate was efficiently bioleached at 50% pulp density with the drum operating at 0.5 -1.0 rpm Attempts of bioleaching the concentrate at the same pulp density in conventional stirred reactor showed severe inhibition of bacterial activity. The results demonstrated that the drum reactor allows to operate at much higher pulp densities than the conventional stirred tank reactor. This behavior is explained in terms of an improvement of the bacterial activity due to a better control of the attrition of the mineral particles.

Jan 1, 1997

By Paul L. Russell

Numbers, arithmetic, mathematics. Where did it all come from? Who needs it? We all do, but many school children would not agree. Engineers, physicists, accountants, tax collectors, and most of the general public are well aware that modern society in large part is founded on mathematics and could not exist without it. Mathematics developed over thousands of years as part of the everyday life of man. No one area, tribe, or race can claim discovery. In fact, from the records that do exist, it is evident that many facets of mathematics were discovered independently of others who made similar discoveries. While proof may be lacking, the earliest concepts of mathematics may be some 250,000 to 300,000 years old. The first use of numbers as written records is unknown. However, a bone of a young wolf deeply cut with 55 notches-arranged in two rows, one of 25 notches, the other of 30-was found in Czechoslovakia. Dated to be about 30,000 years old, it is perhaps an early record of some kind of counting system. It is assumed that mathematics was developed as an answer to man's practical needs, but anthropological studies suggest that the art of counting may have developed in connection with the needs of primitive religious ceremonial rites. Fingers probably were first used to designate sets of from one to five objects. Using both hands, up to 10 items could be indicated. As civilization developed, so did the need for more flexible systems to record items of trade, measure land, and figure taxes. Aristotle noted that the development of the decimal system comes from the fact that most people are born with 10 fingers and 10 toes. In spite of this obvious fact many early civilizations used binary, ternary, and quinary systems while vigesimal systems (with 20 as a base) and even sexagesimal systems (with 60 as a base) were used by others. A form of writing was in use in both the Mesopotamian and Nile valleys as early as 3000 to 4500 B.C. In Mesopotamia, wedge-shaped marks were impressed upon soft clay tablets that were hardened in ovens or by the sun. Many thousands of such tablets have survived. When the tablets were finally deciphered, some were found to be records of items shipped in trade, inventories, tax accounts, and mathematics exercises for teaching. Mesopotamia is also the source of an interesting board game dating back to about 2500 B.C. Its buttonlike men and triangular dice were apparently used with squares of shell, inlaid with lapis lazuli and red sandstone. Unfortunately, rules of play were not found. In Egypt, record preservation was somewhat better. Discovery of the Rosetta Stone in 1799 eventually led to deciphering the Egyptian hieroglyphics that included a numbering system at least 5,000 years old. These records show a competence in counting and numbering. A calendar of good accuracy may have been in existence as early as 4,200 years ago. Mathematics, as practiced today, developed when the Greeks added logic and proof to arithme-

Jan 12, 1982

By N. I. Aziz, B. Srinivasa Rao, R. N. Singh

The control of respirable dust and its subsequent exposure to miners is essential for improved safety in longwall mining. The extensive variation in face conditions and operations of longwall make numerical modelling an attractive approach in both the development and evaluation of dust control devices. Three dimensional finite element computational fluid dynamics code FIDAP was used to model air velocities and the effect of dust control techniques on dust concentrations at a typical longwall face. The effect of shearer body on airflow characteristics in a longwall face was analysed with both antitropal and homotropal ventilation systems. Path traces of particles introduced near the shearer drums was also simulated. Initial modelling results were validated using field trial results at three operating longwall faces. Results of simulations tallied very well with the field results.

Jan 1, 1993

By M. Poulton, J. A. Botín, C. Gatica

"The Chilean minerals industry faces a shortage of 27.000 new skilled professional by 2023. Enhancing the integration of women into the workforce is a possible solution. This study analyzes the state of women in the mining workforce over the past decade. Several key indicators are presented: percent in the workforce, salaries, career profiles, presence at management level, and participation in academia are studied. The study also analyzes the strategies used by government, industry, and universities to recruit and retain women for the minerals industry. The main results show that women represent 7.4% of the mining workforce in Chile and less than 1% of senior positions with a salary gap of approximately 30%. Systematically, women prefer professional programs in geology, chemistry, and environmental areas. The Chilean statistics are compared to data from the United States mining industry. INTRODUCTION The Chilean mining industry faces a significant shortage of professionals for the next decade which compromises competitiveness and productivity. The demand for human capital in mining depends on several factors. First, the age structure of workforce, which determines future retirement needs. Second, minerals market considerations, determining the amount and size of mining projects entering production in the coming years. Third, the evolution, positive or negative, of productivity, mainly driven by technology and innovation, and negatively affected by the declining ore grades. Finally, negative trends in lead times to production of mining projects, due to social opposition, changing regulations and other project contingencies, negatively affecting the demand for human capital. Regarding the supply of human capital, the fast increase in the technology level of the minerals industry and hence, the increase of technical qualification requirements of the human capital generates a rise in the time required for trade and university education of mining professionals, which may cause imbalances in the labor market. According to (Consejo Minero, 2014) human capital gap in Chile by 2023 will be around 27.000 workers for extractive, processing and maintenance jobs, which represents 14% of the current workforce (Figure 1)."

Jan 1, 2016

By J-M M. Rendu

Geostatistics are increasingly recognized as powerful tools for reserve evaluation and grade control. It is also generally accepted that geologic input is required for the results of a geostatistical study to be meaningful. The role of the geologist is significant at all stages, whether it be to oversee the creation of the database, to assist in the statistical and semivariogran studies, to ensure appropriate block evaluation and kriging, or to review the results obtained. However the link between geology and geostatistics is often complex and not well understood. A presentation is made of the areas where geologic input is needed, and of the tools which the geologist should have at his disposition to ensure that his role is fulfilled. Organization of a Geostatisticel Study To be acceptable as the basis for financial investment, a geostatistical reserve estimation should be composed of four phases, the last phase being optional: Phase 1 - Background discussions, Phase 2 - Computation, Phase 3 - Reserve reporting, Phase 4 - Reserve audit. During the background discussions (Phase 1) the role of the geologist is primordial, as it is then that most decisions will be made concerning the geologic factors to be included in the geostatistical model.

Jan 1, 1985

By Alvin W. Schillinger

Drilling was not entirely satisfactory in the search for native copper in the Osceola amygdaloid footwall as mining showed oreshoots to be more continuous than drilling indicated. The Geophysics Department of Michigan Technological University developed a portable induced polarization drill hole probe with a 3 electrode configuration and a sampling radius of 5'± A 20 ma current of alternately reversed polarity is pulsed at 3.5 sec. intervals and readings are taken every two feet. Potential is read during the "on" cycle for resistivity determinations. During the "off" cycle, after 10 ms delay, the I.P. potential is sampled for 10 ms and recorded. Resistivity (ohm-feet) and "S" values (mv/v) are plotted on semi-log paper. A lithologic log is plotted based on resistivity and anomalous "S" values noted. The low resistivity amygdaloid contains sills of high resistivity basaltic trap. Verified by core logs, amygdaloid-trap contacts could be picked to ±.5' from resistivity alone. Lithologic logs of long steel holes, based' on resistivity, now replaced sludge logging. An "S" value of 30 mv/v was established as the lower limit of diagnostic I.P. effects in mineralized amygdaloid and 50 mv/v as a threshold value for ore. Of 914 footwall zones drilled, 315 were probed yielding 203 anomalies. Success increased from 34% for drilling to 72% for drilling and probing. As checked by mining, 46 probe results were 78% correct. Failures were due to the instrument not detecting copper or to the misinterpretation of an anomaly. No false anomalies were found.

Jan 1, 1964

By R. S. Scheetz

The search for a more effective means of coping with methane liberation has resulted in the expanded use of seam degasification. Its advantages are measured not only in reducing the hazards due to methane, but also in producing a marketable commodity: .the gas, itself. However, the success of a methane drainage system is the culmination of many complex factors, the most important being the coal seam permeability. The two most popular drainage techniques used mining today are the vertically simulated borehole method and the in-seam horizontal borehole method. The objective of this paper is to determine the permeability range in which the selection of the degasification technique is based primarily on equipment and economic analysis. A discussion of the equipment involved will be incorporated into examples evaluated by the Penn State coal methane simulation model.

Jan 1, 1989

By A. K. Martin

Adaptive management can be described as a structured, iterative process of robust decision making in the face of uncertainty, with a goal of reducing uncertainty over time through system monitoring. Adaptive management is a tool which can be applied to not only change a system, but learn about the system (Holling, 1978). Adaptive management has been used in ecosystem management for years and guidance is provided in a variety of handbooks and publications. Adaptive management can be applied to industrial facilities and mines through the use of an adaptive environmental management plan (AEMP) and associated practices. The goal of this paper is to provide an explanation of how the plans and practices support regulatory agency approvals and permitting, span the life-cycle of mines, manage uncertainty, and assist in addressing mining impact and legacy issues. AEMPs and associated practices are useful tools to address the uncertainties in identifying, evaluating, and managing impacts of proposed new and modified mining facilities undergoing environmental review. Once a proposed project is approved, the AEMP continues as a living document, being informed, revised, and adapted by the operations. The AEMP can serve as an ongoing management tool for describing and evaluating environmental impacts, continuing in operations into post reclamation. If initiated during planning and environmental review of a project (and in some locations such as the United States [U.S.], the preparation of an Environmental Impact Statement (EIS)), the AEMP becomes a basis to identify, monitor, and manage potential project environmental impacts. Development of an AEMP for an operating mine is also beneficial since there are generally developing and ongoing environmental issues at those facilities as well. Over time, the AEMP is adapted to changing requirements and conditions including those anticipated and unanticipated. Ever increasing scrutiny of mining projects and the complexities of the EIS process highlight the uncertainties inherent in impact predictions. In making the momentous decision of initial project approval, these uncertainties can discourage the regulatory agencies? actions and create stakeholder anxiety and controversy about a project. A well-designed AEMP can support the decision to approve an EIS and enable a project to move forward. Additionally, an AEMP can inform financial assurance estimates and revisions over the life of a mine providing all parties including the citizens of the surrounding communities with greater confidence that potential environmental impacts and risks will be well managed.

Feb 23, 2014

By R. K. Singhal

A sizable surface mining industry exists in Western Canada. There are the surface coal mines in the provinces of Alberta, British Columbia, and Saskatchewan producing the bulk of Canadian Coal. The two oil sands plants in Fort McMurray, Alberta producing synthetic crude oil are surface mining operations. Much of the metalliferous mining in British Columbia is carried out by open pit methods. This paper discusses the current surface mining methods in both of these industries with particular reference to Alberta. Issues relating to environmental impact assessment, mine reclamation and mine site closure have been dealt with.

Jan 1, 1995

By Claus Becker

The Mixshield is a tunnelling machine for water bearing soft soils. Developed on the basis of the Hydroshield, it extents the application of this machine to cohesive soils. The design of the drum-type machine allows three different applications 1. As shield with liquid supported face and hydraulical mucking 2. As Compressed-Air-Shield 3. As Earth pressure balanced shield. The Mixshield is employed on three big contracts 1. a 6.3 km ring tunnel in Hamburg, outer diameter 5.95 m, with a new developed segmented concrete lining 2. a 1.9 km pipe-jack job near Cologne, o.d. 3.6 m 3. Metro Lot 3 in Lille/France, o.d. 7.7 m, 3.2 km long with segmented concrete lining and a most sophisticated separation-plant The site experiences will be reported.

Jan 1, 1987

By Fouad Faraj, Julian M. Ortiz

Within the natural resource industries, there is an increasing amount of data and number of variables being recorded when sampling a site. This has made multivariate geospatial datasets more difficult to analyze, in particular the definition of estimation or simulation domains used in geostatistical analysis. Establishing these domains is typically the first step for any subsequent geostatistical workflows or modeling. Domains are traditionally established using categorical data such as lithology, mineralization, or alteration from geological logging and are aimed at identifying distinct populations with particular geological, spatial, and statistical features. The manual logging process is time-consuming and costly but is required because defining geologically homogenous volumes is crucial for the planning, extraction, and processing of natural resources. Classical clustering methods have aided in analyzing the multivariate datasets, but the resulting clusters from these methods do not correlate well with geological logging and do not allow practitioners to input their knowledge of the domain in the clustering process. In this work, a simple unsupervised classification workflow is presented which allows the practitioner to input domain knowledge by selecting relevant variables to cluster reasonable geological domains. This can be used as a tool to aid the manual logging procedure or as a tool to establish domains for different uses such as defining zones with different rock hardness distributions which allows the corresponding volumes to be sent to appropriate mills for efficient mineral processing. The performance of the workflow is assessed on a mining dataset using the geochemical information and validated with the geological logging.

Apr 16, 2021

By Stephen G. Hardcastle

3D-CANVENT is a software package that integrates advanced computer aided design (ACRD) true 3D graphics with a mine ventilation simulator. The package runs as a Windows(tm) application to access its printer drivers environment and does not need third party CAD software. It is composed of two primary modules: DMVENT and MINEDESIGNER. DMVENT is a traditional Fortran coded Hardy-Cross iterative ventilation network solver written in 1980 with thermodynamic capabilities. This module is relatively unchanged with the traditional data input options for branch type, specified or calculated resistances, fixed flows, and fixed or variable pressure fans. MINEDESIGNER is the graphics engine that optimizes the ventilation design process. It performs the front-end transformation of input data entered in the graphical interface into the correct format for the solver. At the back-end it reconverts the historically standard tabular data output from the solver into an easily viewed graphical format. ACRD features of MINEDESIGNER are used to generate a 3D wire-frame node and branch network of the mine's ventilation system. The network can be displayed in up to 4 views orientated to XYZ planes or a 3D view. All the views have zoom, pan, slice and rotate options. The graphical interface efficiently permits data entry and editing via a mouse with pick-and-point item selection. Branches can be found or added with "search" and "join" options. Visual interpretation is enhanced by the 16 colour options for branches and numerous graphical attributes. Network locations are readily identified by alpha-numeric names for branches, junctions and fans, and also the logical numbering of junctions. The program is also readily expandable for pollutant simulation and control/monitoring applications.

Jan 1, 1995

By C. J. Pritchard

Productivity improvements reduced the number of continuous miner sections from seven to three while maintaining full productive capacity. So a decision was made to test an advancing tailgate ventilation system on the shortwall mining section. Having the shortwall mine its own return air system has freed the third mining section for more productive, less costly mining. The advancing tailgate has provided effective ventilation across the face and gob with acceptable pressure losses. The low-productivity, tailgate-development, continuous-miner section has been transformed into to a high-productivity, development-retreat section that is also available for long-term mine development duties, increasing mine planning flexibility.

Jan 1, 1991

By H. Lyn Bourne

Daily everyone depends on the great variety of glass products, so much so that glass is often taken for granted. In fact most people do not realize how versatile glass has become. Consider the various uses and then try to imagine a day in which we are not influenced by glass. Common uses include container ware, table ware, window glass, lead crystal, automobile glass, and fiber glass. Several less common, but important, uses include laboratory ware, pharmaceutical, TV bulbs, light bulbs, glass ceramics, optical glass, fiber optics, and laser glass. Corning, Inc., a leader in specialty products, uses nearly 1 000 different compositions to manufacture about 60 000 different products (Edwards and Copley, 1977). Glass is such a complex product that-definitions vary and exceptions can be found for most definitions. Glass is an inorganic amorphous (non-crystalline) solid. Most glasses are produced by melting of a mixture of oxide raw materials, and then cooled to room temperature. Soda-lime-silica composition.s account for about 90% of all glasses melted (Anon, 1973). The properties of the glass product come mainly from its chemical composition. All of the different glasses require melting a combination of raw materials and forming the molten material into the desired shape. Both the melting and the forming processes use sophisticated technology and these technologies require experts to manage these production systems. The manufacturing process is continuous and takes place in tonnage quantities, so adjustments in the batch to achieve the desired finished product requires a great deal of expertise. Raw materials are fed to the batch mixing area in very large quantities (tons in most cases). As a result, impurities in the range of 0.1% result in addition of that impurity within the molten glass in kilogram amounts. More than twenty different industrial minerals are consumed in the manufacture of various kinds of glass (O'Driscoll, 1990). This chapter describes the major and minor ingredients of the various glass batches. It discusses the roles of the various oxides in the glass batch and most importantly considers the mineral raw materials which supply the glass industry. Each of the raw materials is described in detail in other chapters so the geology and mineralogy sections are kept brief here. Container glass, by far, accounts for the most production; followed by flat glass, fiber glass, and specialty glass of which table ware accounts for the greatest tonnage. [Table 1] shows the general production data for 1987 through 1990. Statistics for many of the uses do not appear because production volumes are small compared to the major uses. The glass industry is organized in four categories: containers, flat glass, fiber glass and specialty glass. The US Department of Commerce, Bureau of Census, publishes production data about the glass industry in three different categories: 1) glass containers, 2) consumer, scientific, technical and industrial glassware, and 3) flat glass. The Bureau has very complete statistics about the glass industry in these three categories but they report production data in different units according to industry standards. Therefore, [Table 1] gives the production data in dissimilar units. The production of most glass articles follows similar steps. The raw materials are mixed and the resulting batch is fed into the furnace. In soda-lime-silica glasses melting begins between 600 and 900°C. At these temperatures CO, and other gasses are released which create bubbles in the molten glass. To remove the bubbles and insure complete melting the temperature is raised to between 1 500 and 1 600°C. This is the melting-refining stage during which the refining agents in the glass batch serve to aid in the release of gas bubbles, homogenize the melt, and prevent the formation of scum on the surface of the molten liquid. At the conclusion of the melting-refining stage the glass is too fluid for working and the melt is cooled to about 1 100°C to attain the proper viscosity for working and forming to begin. After the glass article has been made, it must undergo annealing (slowly and uniformly reheated and cooled) to remove thermal stresses that were created during the forming process.

Jan 1, 1994

By George Alan Weed

The management of safety is not only the most noble, but also the most personally and financially rewarding of all the management functions. The management of safety should result in the prevention of accidents and the elimination of human suffering and loss of life. Safety management must be the number one priority of all management's production and profit objectives. For years, safety management has been a result of mockery, charlatanism and snake oil presentations dedicated to giving a quick dog and pony show. The result has been an unacceptable record of accidents and fatalities.

Jan 1, 1981