Search Documents

By L. Giraldo, S. Cotten

"INTRODUCTION The vision for a “Mine Escape Vehicle” (MEV) is to provide capabilities to better enable underground travel to allow miners to escape to safety in the event of a major mine emergency such as a fire or explosion. Enhanced transportation and survival capability such as a MEV may have minimized or eliminated the loss of life associated with several of the mine disasters that occurred in 2006, which together resulted in the deaths of 19 miners. Although the most desirable response in an emergency is for the miners exit the mine, if escape proved to be impossible, the miners could use the vehicle to proceed to an underground point of refuge to await rescue. Under a NIOSH contract issued in April 2008, Raytheon developed a conceptual vehicle design including (1) the capacity to provide life support functions for a number of miners, (2) operate in a reduced oxygen atmosphere with little or no visibility, and (3) travel at speeds faster than miners could walk out of the mine. The proposed MEV concept envisioned modification of a personnel carrier (a.k.a. a “mantrip”) that would be used every day during normal mine operations, not a specialized vehicle reserved only for or dedicated solely to escape. The MEV concept also included escape aids that are detachable from the vehicle in the event that the vehicle must be abandoned on the way out of the mine and the dismounted miners had to proceed on foot. To advance MEV development, NIOSH awarded a second contract in 2010 to Raytheon to build, test, and evaluate the performance of a proof-of-concept MEV that culminated in a 7-month performance evaluation of vehicle in an Eastern Kentucky coal mine (Figure 1). User feedback and lessons learned from the proof-of-concept vehicle evaluation provided support for the general MEV approach, guidance related to the practicality of MEV capabilities, and indication of specific technology shortcomings for this application."

Jan 1, 2015

By M. P. Neira

In-situ leaching of copper from chalcocite relies on ferric iron concentration in the lixiviant being reduced to ferrous. To re-establish the ferric concentration in solution, ferrous must be re-oxidized. This reaction is slow under normal chemical conditions but it is catalyzed by Thiobacillus ferrooxidans bacteria. BHP Copper's Miami In-situ unit developed a bio-reactor as a method of oxidizing ferrous to ferric. The effects on oxidation of temperature, CO2? oxygen, and air injection flowrate were defined. This paper summarizes the results of ferrous bio-oxidation using plastic column packing and oxide ores as bio-reactors and the leaching results of the bio-reacted lixiviant on chalcocite ores.

Jan 1, 1997

By Tyler A. Dawson, Ryan P. Butler, Timothy Gualandri, Jason R. Edberg

"In the early 1920’s, the City of Tulsa, Oklahoma constructed an approximately 8,238-foot long tunnel, the Tiawah Tunnel, through bedrock. Voids behind the concrete tunnel liner were detected via probe drilling in early 2000 as part of an interior visual condition assessment. In 2012 and 2015, conditions along the entire tunnel were efficiently assessed through geophysical investigation using ground penetrating radar (GPR) along the inner tunnel crown and at various select locations within the tunnel. Fifty-seven (57) potential voids, extending up to 19 inches in depth and 12 feet in width, were detected with 1,000 MHz GPR and confirmed through probe drilling with approximately 80% accuracy. GPR proved to be an efficient and reliable technology for void detection behind concrete tunnel lining. This paper highlights the geophysical investigation and how geophysical efforts were combined with other investigation efforts to definitively determine the presence of voids outside of the tunnel lining.INTRODUCTION The city of Tulsa, Oklahoma has a population of about 400,000 people. The original source of water for the city was the Arkansas River. The first pumping operation provided untreated water to homes and businesses in 1904. The residents of Tulsa found this water to be unacceptable due to the high levels of salt and gypsum present. As the city grew, land and storage/treatment facilities were acquired in order to obtain and distribute a more suitable raw water. The raw water needs for the city are currently satisfied by transport and treatment of about 100 million gallons per day (MGD) of water from surface water sources. Water is transported many miles from Spavinaw/Eucha and Oologah lakes to Yahola Lake and the Lynn Lane Reservoir (totaling over 3-billion gallon capacity). From here, the raw water is treated and transported to the various customers (City of Tulsa 2015). The Tulsa Metropolitan Utility Authority (TMUA) is responsible for the operation and maintenance of the raw water transport system."

Jan 1, 2016

By Roberto de Moraes

Lunar construction faces unique challenges arising from the nature of regolith and megaregolith. Unlike terrestrial soils shaped by weathering, lunar regolith is composed of angular, poorly sorted particles produced by impacts, with bulk Density, strength, and trafficability varying sharply with depth and terrain. Boulder fields, floaters, and talus aprons add further complexity, disrupting excavation and mobility. Apollo missions documented these conditions through drive-tube samples, trenching, penetrometer data, trafficability tests, and seismic profiling, but the results remained as datasets rather than a unifying classification. This paper introduces the LRC (Lunar Regolith Classification) Framework and the Overconsolidation Ratio applied for the Moon (OCR*), the first contractor-ready system to organize Apollo-derived trends into excavation demand zones (L1–L5). LRC is explicitly a classification, not a stratigraphy: depth ranges are indicative and require in-situ verification before use. Each zone is defined by bulk density and strength ranges, field proxies (bootprints, trench stability, auger torque, seismic contrasts), and corresponding excavation implications. Worked examples from Apollo 15 (mare), Apollo 16 (highlands), and Apollo 17 (pyroclastics and talus) demonstrate how observed data translate into LRC zones. These cases show that LRC captures both systematic depth trends and sharp local heterogeneity. The framework standardizes excavation planning for landing pads, haul roads, berms, foundations, and tunneling trials, while converting floaters from hazards into resources. LRC thus provides a common language for lunar construction. Rooted in Apollo evidence but designed for Artemis verification, it is proposed as a living standard; a reference framework to guide site preparation, excavation, and risk management in the next phase of lunar development.

Feb 22, 2026

By S. Gering, R. Ruiz, C. H. Calderon-Arteaga, J. Barrios

"INTRODUCTION Located in the northeast corner of Zacatecas State, Mexico, the Peñasquito Operation is comprised of the Peñasco and Chile Colorado (Brecha Azul) deposits. Open pit mining (pre-stripping) began in 2010 and full production commenced during 2011. The open pit mines feed both a sulphide concentrator (mill) and a heap leach pad. The project is owned by Goldcorp, Inc. Penasquito is a poly metallic deposit with Au, Ag, Zn and Pb being recovered as payable metals. As a consequence of lower grade ores expected with advancing mine-life Peñasquito is facing a declining metal production profile. To maximize returns and asset value plant modifications including the addition of a carbon pre-float circuit and a pyrite leach circuit to improve recovery are currently being undertaken. This carbon pre-float circuit will enable the recovery of precious and base metals from carbonaceous sediments. This material is currently being stockpiled. With the associated increase in complexity in the process circuit, the requirement of the ore control system to accurately predict ore feed characteristics is critical to maximizing metal recovery at the Penasquito operation. The addition of the carbon pre-float circuit was also a key driver in allowing the Chile Colorado open pit to be developed. These conditions alongside Goldcorp’s drive to increase profitability, and maximize net asset value has created challenges. These challenges are numerous and are multifaceted, however the ability to accurately route materials from the ore control system is critical to site success, and some of these challenges have been overcome by the adoption and implementation of a new ore control (OC) technology. Examples of these technological innovations in the ore control program are discussed in this paper and include improvements in geo-modeling, material routing and reconciliation. Successful implementation of these elements has led to significant improvements in selectivity, performance, and data management, while reducing the variance between planning and execution, thus helping to drive overall improvement across the operation."

Jan 1, 2018

By E. W. Geist

This paper is presented from the viewpoint of the mill operator and maintenance supervisor. Its purpose is to highlight the things that have been accomplished by the mill designers to lighten the load for the maintenance superintendent and to reduce the overall costs for the plant operator. The complexity of plant design, the civil and structural engineering problems encountered when the satisfactory maintenance layout is accomplished are appreciated, and the writer is fully aware of the complexities of these problems. However, it is not the purpose of this particular paper to dwell upon these problems, nor to emphasize or de-emphasize the problems of the civil, mechanical and electrical engineers. It is simply that the paper will attempt to review what these people have accomplished in spite of the many technical problems. This paper then is prepared with the operator and maintenance people?s viewpoint. What is their definition of design for maintenance? It is the writer's interpretation that the various design concepts which mean improved maintenance are such items as (I) maintenance areas, (2) laydown space for maintenance materials in specific maintenance jobs, (3) the inclusion of bridge cranes in the plant and specific design of the craneways to accomplish flexibilities for the cranes, and (4) the location of the piece of equipment to allow maintenance people to work around the equipment - - - this specifically includes the orientation of the particular piece of equipment.

Jan 1, 1967

By Josh Swank

Albert Einstein once said, ?the important thing is not to stop questioning.? In the mining industry, a lack of inquisitiveness may lead to a blissful ignorance but it certainly will not increase efficiencies. While one may claim necessity is the mother of invention, questioning and analyzing how methods and systems can be improved is the catalyst to discovering necessities. Understandably, when working in the middle of Canada?s oil sands, where trucks operate around the clock every day of the year, it is nearly impossible to pull the nose from the grindstone long enough to provide thorough analysis. But, fortunately, some manufacturers/inventors have assisted by examining the process and the ensuing headaches within this application.

Jan 1, 2013

By T. Grammatikopoulos, C. Gibson, M. Aghamirian

"Lithium is a silver-white alkali metal that has recently become a target commodity for many junior mining companies. Lithium has a wide range of applications including ceramics and glass, lubricating greases, air treatment, continuous cast mold flux powders, polymer production, and primary aluminium production, but the current popularity of lithium can be attributed to an anticipated increase in demand for lithium ion batteries. The most common lithium-bearing minerals occur globally in pegmatites and granites. Spodumene [LiAl(Si2O6)] is the most desirable economic lithium-bearing mineral due to its high lithium content (theoretical Li2O content of about 8 wt%). However, lithium can also be hosted in petalite, micas, tourmaline, and phosphate minerals. In Canada there are a number of spodumene deposits in Ontario and Quebec at development stage that have the potential to help narrow the forecast lithium supply gap stemming from the widespread acceptance and use of electric vehicles. This paper discusses the beneficiation of hard rock lithium deposits, including an in depth review of the use of flotation to upgrade spodumene. A review of the use of dense media separation (DMS), magnetic separation, and roasting as means to process spodumene bearing ores is also discussed. INTRODUCTION Lithium is a soft, silver-white alkali metal with atomic number 3. As of 2015, the end use of lithium was estimated to be as follows: lithium-ion batteries (35%), ceramics and glass (32%), lubricating greases (9%), air treatment (5%), continuous casting mould flux powders (5%), polymer production (4%), primary aluminium production (1%) and other uses (9%) (Jaskula, 2014). Lithium is found in brine lake deposits containing lithium chloride and in hard rock pegmatite deposits. It can be sold in a range of product types; as mineral concentrate, brine, compound (lithium carbonate or lithium hydroxide) and metal depending on its intended end use (Goonan, 2012; Jaskula 2014). In the 1990s the United States and Chile were the largest producers of lithium globally, primarily from brine operations (Ober, 1994). Most of the lithium compounds produced over this period were consumed in the glass, ceramics and aluminium industries. In the 1980s and 1990s there were two major lithium operations in the United States: brine operations at Silver Peak, Nevada, and a spodumene mine and lithium carbonate/lithium hydroxide plant in Kings Mountain, North Carolina. The Kings Mountain operations ceased production in 1991 and were eventually dismantled in 1994. Brine operations were also active in Argentina and Chile, while the largest lithium ore deposit in the world was operated at Greenbushes, Western Australia. During this period it was predicted that major shifts in demand for lithium would come from the success and widespread use of electric vehicles (Ober, 1994)."

Jan 1, 2017

By P. T. Bissert, T. J. Lutz, J. A. Yonkey, G. T. Homce

"Underground refuge alternatives require an air source to supply breathable air to the occupants. This requires pressure relief valves to prevent unsafe pressures from building up within the refuge alternative. The U.S. Mine Safety and Health Administration (MSHA) mandates that pressure relief valves prevent pressure from exceeding 1.25 kPa (0.18 psi), or as specified by the manufacturer, above mine atmospheric pressure when a fan or compressor is used for the air supply. The U.S. National Institute for Occupational Safety and Health (NIOSH) tested a variety of pressure relief valves using an instrumented test fixture consisting of data acquisition equipment, a centrifugal blower, ductwork and various sensors to determine if the subject pressure relief valves meet the MSHA requirement. Relief pressures and flow characteristics, including opening pressure and flow rate, were measured for five different pressure relief valves under a variety of conditions. The subject pressure relief valves included two off-theshelf modified check valves, two check valves used in MSHA-approved built-in-place refuge alternatives, and a commercially available valve that was designed for a steel refuge alternative and is currently being used in some built-in-place refuge alternatives. The test results showed relief pressures ranging from 0.20 to 1.53 kPa (0.03 to 0.22 psi) and flow rates up to 19.3 m3/ min (683 scfm). As tested, some of the pressure relief valves did not meet the 1.25 kPa (0.18 psi) relief specification.IntroductionThe Mine Improvement and New Emergency Response Act of 2006 (MINER Act) was enacted in the United States in the wake of three mine explosions/fires that claimed 19 lives that year. Intended to help improve underground coal mine accident preparedness, the MINER Act includes provisions that target mine safety issues in areas such as emergency response planning, adoption of new technology, training and education, and mine safety standards enforcement (U.S. Mine Safety and Health Administration, MSHA, 2006). Section 13 of the MINER Act specifically directed the U.S. National Institute for Occupational Safety and Health (NIOSH) to provide for research into the effectiveness and viability of refuge alternatives for underground coal mines. This mandate culminated in the 2009 adoption of changes to Title 30 of the Code of Federal Regulations (30 CFR) mining health and safety regulations, requiring underground coal mines to provide mine emergency refuge alternatives and associated components, to provide a life-sustaining environment for persons trapped underground. Such refuge alternatives can be either self-contained mobile units or built-inplace facilities. The regulatory changes also include provisions establishing requirements for MSHA approval of refuge alternatives and their components, and among these provisions are numerous criteria for providing a safe breathable atmosphere under positive pressure within the refuge alternatives. One specific criterion for maintaining a safe refuge alternative atmosphere requires the inclusion of an air pressure relief valve that will activate at a maximum of 1.25 kPa (0.18 psi), or at a pressure above mine atmospheric pressure, in the refuge alternative, as specified by the manufacturer when the breathable air is supplied by a fan or compressor (MSHA, 2008)."

Jan 3, 2018

By James Westfield

I welcome this opportunity to appear before you and to review briefly the various health and safety services of the Bureau of Mines available to the mining industry, other than coal, and also to tell of our plans for extending these services to improve safety and health conditions. The Bureau's health and safety activities are basically services by which we attempt to develop and disseminate information on improved techniques in mine accident prevention and promote mine safety education in the mineral industries. Unfortunately, some mining companies, particularly some of the smaller operations, seem to be unfamiliar with these services, The Bureau of Mines is charged by law with the responsibility for inspecting coal mines; other services to the coal mining industry and are provided only on request, Safety inspections and other services that we offer are provided for noncoal mining industries solely upon request.

Jan 1, 1958

By E. R. Dotson

Kaolin is an important industrial mineral. It has unique properties, which combined with its low cost, make it suitable for use in a wide variety of products. Kaolin is defined as "any of a group of clay minerals, including kaolinite, nacrite, dickite, and anauxite, with a two-layer crystal in which silicon-oxygen and aluminum-hydroxyl sheets alternate; approximate composition is AlZ03-ZSiOZ-1/ ZHZO".-The kaolin discussed here is composed chiefly of the mineral kaolinite. Kaolin is also commonly referred to as "china clay". Approximately 4.9 kkg (5.4 million short tons) of kaolin was sold or used in the United States, and .8 million kkg (.9 million short tons) was -exported in 1974. In domestic usage, paper coating and filling accounted for 43% of the total, fol-2/ lowed by refractories, rubber, and ceramics.-Figure 1 shows the amount of kaolin sold or used by domestic producers for specified uses for the years 1963-3/ 1973.- Kaolin was produced at mines in 14 states, but Georgia accounted for 75% of the 1974 domestic production. The average value for all grades was $36.00/kkg 4/ ($32. 67/ton) .-

Jan 1, 1977

By J. Hupka

Some aspects of kerosene penetration into tar sand have been investigated. The natural tar sand porosity was measured and used to analyze the performance of the hot water process. Subsequently, pretreatment experiments, using 20 kg tar sand samples (Asphalt Ridge and Whiterocks, Utah), and kerosene as a diluent were carried out at the expected summer temperature (26°C) and the expected winter temperature (-14°C). The natural tar sand porosity accessible by diluent has a crucial impact on the reduction of bitumen viscosity, and influences the penetration time required for successful bitumen separation from tar sand by hot water processing. Thus the tar sand porosity is an important variable which determines appropriate operating conditions. Experimental results indicate that diluent penetration into the Asphalt Ridge tar sand (high porosity) is almost complete after 30 min, whereas for the Whiterocks tar sand (low porosity) the penetration process is much slower, and still not complete after 15 hours regardless of the ambient temperature.

Jan 1, 1992

By A. D. S. Gillies, Hsin Wei Wu

An evaluation of the use of air cooling power as an index of the thermal environment is discussed. A body temperature prediction -. model based on body temperature tests, a concept linked to a maximum safe body temperature and the predicted fourth hour body temperature which depends on the rate of heat accumulation (heat storage) within the body has been developed and tested. This has led to the conceptual development of a personal response heat stress meter calibrated to the physiology of the personnel within the workplace. The proposed heat stress meter will be able to measure workplace environmental parameters such as air temperature, humidity and air velocity and the user can either select or manually enter other heat stress parameters such as work rate, clothing type and subject's personal response to heat. With a built-in computer program, the meter will calculate the ACP of the workplace, the fourth hour body core temperature expected and the maximum safe working time allowed for a pre- defined limiting body temperature. A brief description of the work required for developing the meter is included. The potential benefits of such instrument to the mining industry are also evaluated.

Jan 1, 1997

By Owens S. Roberts

The drive selected for any piece of machinery must adequately satisfy the application requirements both during the starting interval and at running conditions, All loading possibilities of the drive must be known and allowances made for any adverse limiting conditions such as extreme cold, or perhaps an intermittent excessive loading situation etc. In general, the drive must be selected to provide the required operating characteristics with maximum reliability and at minimum cost. Simplicity of overall design is always an advantage and care must be exercised to insure that systems incorporating unnecessary complicated parts are not indiscriminantly provided. Important non-technical considerations such as equipment avail-ability (on an overseas project) as well as standardization details also play a role in the drive selection process. Additionally, an assessment of the potential capabilities of the personnel that will have to maintain the equipment can have some influence on the final choice. Several types of prime movers are available but this article will restrict itself to the use of induction motors operating from an available alternating current power source. Many drive arrangements are possible, the most common being the direct coupled single motor arrangement. It is sometimes desirable to use more than one motor per machine, but these designs are usually more

Jan 1, 1971

By Richard L. Breithaupt

INTRODUCTION A shuttle car is a self-propelled rubber-tired haul¬age vehicle designed specifically for underground min¬ing, primarily in coal mines (see Figs. 1 and 2). The drive mechanism is located on the sides of the vehicle, and the load is carried in the center. A chain-and-flight conveyor distributes the load when the car is being loaded by a loading machine or continuous miner and also discharges the load onto a conveyor belt or into a mine car. As the name implies, the shuttle car shuttles back and forth between the working face and the un¬loading point and is not required to turn around. Shuttle cars have served as primary haulage in this country since 1940 and still perform this function in most coal mines today. TYPES OF SHUTTLE CARS Shuttle cars may be battery-powered, diesel-powered, or cable-reel electric powered. Battery-powered cars were used between 1940 and 1950, but are almost out of existence today because of their limited power. Diesel cars have been used in coal mines, but are used mostly in noncoal mines where rules and regulations are not as stringent. Also, objections by organized labor have limited the use of diesel-powered shuttle cars in coal mines. Today, the largest number of shuttle cars are cable-reel cars. Electric power is fed through a cable stored on a cable reel that may have a capacity from 152 to 244 m (500 to 800 ft), depending upon the size of the cable and the cable reel (see Table 1). This, of course, limits the travel of a shuttle car. However, time studies have shown that for the most efficient haulage cycle, the length of haulage should not exceed 91 m (300 ft). As haulage distance increases, the waiting time for the loader or miner becomes longer, and haul¬age efficiency suffers. Cable-reel cars are manufactured in standard hand and opposite standard hand models. A standard car has the operator's control on the left front side and the opposite standard car has the opera¬tor's controls on the right front. Generally a loader or miner operates with two shuttle cars, one of each type. This allows the trailing cable to lie on either side of the entry and prevents the cables from fouling each other. Shuttle cars are designed to operate with either dc or ac power. Cars using dc power are designed for 250-v supply and ac cars are designed for either 440, 550, or 950 v, three-phase voltage. Most coal mines that are relatively level can use dc cars where dynamic brak¬ing is not required. For mines having steep grades (in excess of 15%) ac cars are used because ac traction motors have inherent dynamic braking and are safer when tramming downgrade. A recent innovation in shuttle car design in the last five years has been the introduction of an ac/dc car. This design utilizes ac input power through the cable, and the power is rectified on the car to 250-v do for traction motors. The pump motor and conveyor motor are powered by ac voltage. The main advantage of this design is efficiency-a much smaller cable may be used and the smooth operating characteristics of the dc traction motor is obtained. This prevents shock loading on the traction drive train, which is an undesirable feature of ac traction motors. SHUTTLE CAR FEATURES Elevating Discharge Today, all shuttle cars are equipped with an elevating front conveyor that allows the shuttle car to discharge into a mine car or belt feeder without the use of ramps. Hydraulic Power System Today, all shuttle cars are equipped with an hy¬draulic power system. An hydraulic pump is driven by an electric motor which provides hydraulic power for steering, elevating the front conveyor, and powering the

Jan 1, 1982

By Jürgen Kretschmann

The European climate and energy framework for 2030 is highlighting the reduction of man-made CO2 by increasing the use of renewable energy to mitigate climate change. In this spirit, Germany has decided to erase the coal use as an energy source by 2038 completely. Inevitably, this strategy promises a feasible, responsible, and sustainable post-mining management, because 200 years of coal mining have created numerous challenges necessary to tend to once the mining ends. Thus, the Research Institute for Post- Mining (FZN) at the TH Georg Agricola University in Bochum, Germany, has developed a holistic approach to meet these postmining challenges including further expertise present at our university. Here, the four strategic research pillars are (1) technical geoecology and hydrogeology to avoid and mitigate risks underground, (2) geomonitoring to evaluate and protect the surface, (3) industrial heritage preservation and engineering to secure and reuse brownfields such as mine sites, and (4) economic transformation planning of mining regions to enable a prosper future for generations to come. In all efforts, we aim to achieve the fundamental goals of the UN to deal with the resources of our planet responsibly and sustainably. Furthermore, we are synergizing increasingly with national and international networks in the interest of social, economic, and environmental stakeholders.

Jul 23, 2020

By Donald P. Richards

Is a shaft the same as a tunnel and can it be approached in the same manner for design and construction? The most obvious difference between a shaft and a tunnel is that of orientation; whereas a tunnel is commonly near horizontal or slightly dipping, a shaft is commonly vertical or steeply inclined. As a result, design and construction methods employed for tunneling, in general, cannot be directly applied to shafts, although some of the basic concepts of behavior are quite similar. Many of the shafts that have been sunk in various parts of the world are owned by private mining companies. Each company has generally accumulated years of experience in shaft sinking and mining techniques pertinent to its particular geographic location. When a new shaft is to be sunk or an existing shaft deepened, the tendency often seems to be to continue to use the methods that have been used successfully in the past.

Jan 1, 1979

By Norman F. Schulz

Representative sample s of typical manganiferous iron ores from the Cuyuna Range, Minnesota, were reduced to the metallic iron state at temperatures just short of fusion with an excess of coke in the manner prescribed by the R-N Direct Reduction Process. The magnetic separation characteristics of the reduced ores were determined at several grinds by means of the Davis magnetic tube concentrator. The efficiency of metallic iron concentration by magnetic separation was a direct function of the degree of metallization of the ore sample and of the degree of liberation attained in grinding. Some improvement of liberation characteristics was observed if a small amount of sodium chloride was present in the ore during reduction. Despite the extremely fine -grained structure of the crude ores, iron concentrates containing more than 90% Fe at iron unit recoveries of 90% or more were obtained from well-metallized samples of three of the four ores tested. The rejection of manganese to the tailings corresponding to such separations varied from 80 to 95%.

Jan 1, 1967

By M. L. Harris

Explosions in underground mines and surface facilities such as processing plants are caused by confined accumulations of combustible dust and/or flammable gas mixed with air in the presence of an ignition source. Underground explosions can be prevented by minimizing methane concentrations through methane drainage and ventilation, by adding sufficient rock dust to inert the coal dust, and by eliminating ignition sources. The effectiveness of rock dust in arresting explosion propagation was proven by experiment and practice (1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11). The precise mechanism by which rock dust (generally pulverized limestone dust) quenches flame has not been fully explained, but is believed to be absorption of thermal energy from the heated gases and absorption of radiant energy, which reduces the preheating of unburned coal particles ahead of the flame front. One measurable aspect of explosibility is incombustible content. In order to determine whether enough rock dust is applied, 30 CFR1 § 75.403, Maintenance of Incombustible Content of Rock Dust, requires at least 80% incombustible content on the roof, ribs, and floor of underground coal mines. 30 CFR § 75.403-1 further defines the incombustible content as follows: ?Moisture contained in the combined coal dust, rock dust and other dusts shall be considered as a part of the incombustible content of such mixture.? In order to determine the incombustible content of the mine dust, samples of deposited dust from specified areas in a mine must be collected, analyzed, and then compared with the minimum standard of 80%. The traditional low temperature ashing (LTA) approach to determine if a coal and rock dust mixture is compliant with the inerting requirement consumes the coal dust and considers the remaining material to be inert. Compliance with the law is then determined by comparing the measured percentage of inert material of the representative band sample with the pre-established requirement of 80%. The incombustible content of the sample includes rock dust, the amount of moisture as received at the lab, and the inherent ash in the coal. The LTA method is not itself a direct measure of explosibility but is a surrogate that calculates a single parameter associated with large-scale Bruceton Experimental Mine (BEM) explosion test results conducted with dry rock dust. This method assumes a homogenous mixture with no layering of rock dust and coal dust. Float coal dust is a serious explosion hazard if it accumulates on top of the rock dust and is not mixed with the rock dust (12). Mitchell and Nagy (13) studied the effectiveness of water as an inerting agent for the coal dust explosion hazard. The study emphasized that surface water evaporates readily from dusts. Thus, in a passageway where the dust is wet, changes in weather or the ventilation system could dry the dust and make it unsafe in a relatively short period of time. Where adequate rock dust has been applied, this drying effect is not a factor. However, if the mine depends upon the moisture content as part of the incombustible content, fluctuations in the dust surface moisture within a mine can render moisture content an ineffective and inconsistent measure of safety. Additionally, if sufficient moisture is absorbed and subsequently relinquished by rock dust, a cake can form and render the rock dust ineffectual. The trend has long been recognized that mine explosions occur primarily during the winter season when the humidity is low for long periods of time (14, 15, 16). In light of this trend and due to the potential variability of the moisture content of the dust, it may not be prudent to include variable surface moisture in the total incombustible content of the sample. Instead, surface moisture should be viewed as an additional safety measure as long as the rock dust is dispersible. However, moisture limits the ability of the rock dust to disperse and can significantly reduce its capacity to effectively inert propagating explosions (2, 13, 17, 18, 19, 20, 21, 22). Given the methods by which the as-received moisture and incombustible content are determined, dust samples from the 2010 MSHA database were assessed to determine the variability of the moisture content throughout a year and how often the measured as-received moisture might have affected the dust explosibility determination if removed. The findings were then verified by observation in laboratory studies and within the NIOSH OMSHR Safety Research Coal Mine (SRCM).

Feb 23, 2014

By Robert J. Collins

Computer-aided design drafting systems have been employed in plant design for nearly ten years. Current and future systems will include computer-aided engineering as well. This paper will explore the history and development of such systems including computer and workstation hardware, graphics software, and plant design applications software. The paper will also address future systems and will present both the system vendor and the mine mill designer's view. Specific examples of particularly successful applications will be included.

Jan 1, 1985