Search Documents

By P. K. Sollars, M. A. Alspaugh

In May of 1996, Twentymile Coal Co. began Longwall mining in the Foidel Creek Mine's East Mine District. These Longwall panels are some of the longest in the world (5.48 km/18,000 ft) with very difficult and challenging geometry. The conveyance system is 1,800 mm (72 in) wide, has a 4,500 mtph (5,000 stph) capacity and employs multiple tripper drives. The trippers include traditional powering designs as well as unique regeneration and braking designs. Several components were developed specifically for this application including a mobile tail brake. Control algorithms were carefully developed and tested via computer modeling. A world production record was achieved in the third month of operation and over 1 million tons were mined in June 1997.

Jan 1, 1998

By A. Halim, J. Gustafsson, A. van Wageningen, J. Johansson, · J. Lööw, K. Kocsis

A major part of the European Union’s (EU) project Sustainable Intelligent Mining System (SIMS) is investigating the development of diesel-free/carbon–neutral underground mines in order to ensure sustainable underground mining in the future. Replacing diesel machines with electric vehicles in underground hard rock mines has been widely acknowledged by the mining industry worldwide as a critical step to improve working conditions by reducing diesel exhaust–related contaminants, to reduce mine ventilation electrical power cost by reducing mine airflow quantity, and to reduce mine greenhouse gas emissions. All of these are major requirements to achieve sustainable future underground mining practices. A field trial of Epiroc’s 2nd generation of Battery Electric Vehicles (BEVs) at Agnico Eagle Finland’s Kittilä mine was conducted during 2019–2020. Vehicles tested were MT42 mine truck, ST14 Load-Haul-Dump (LHD), and Boomer E2 jumbo drill rig. This paper outlines the improvement of the working conditions observed in the field trial, and the opinions of the mine personnel at Kittilä mine on using BEVs instead of diesel machines. Measurements of atmospheric contaminants and air temperatures taken during the field trial clearly demonstrated a significant improvement of working conditions when BEVs were operating as opposed to diesel machines. This field observation was supported by the opinion of the majority of the Kittilä mine workers. However, some remaining concerns must be addressed before BEVs can replace diesel machines.

Oct 25, 2021

By P. J. G. du Toi

Anaconda's experience with percussion longhole drilling in Butte, Montana, has consisted of six phases: 1. Drilling horizontal blast holes in stopes with push feeds. 2. Ring and parallel blast hole drilling in longhole stopes with bar mounted as well as skid jumbo mounted longhole drifters. 3. Ring and parallel drilling in raise climber shrinkage stoping using special raise climber drilling decks designed and built in Butte, Montana. 4. Parallel longhole drilling in horizontal cut and fill stopes with monorail jumbo. 5. Drilling water drain holes between mine levels. 6. Drilling leach holes through caved zones into old stope workings for leaching purposes. 7. Sample hole drilling.

Jan 1, 1970

By C. Anderson, B. Schug, C. Cristoffanini, S. Nazari

The Haile Gold Mine in South Carolina is increasing the automation level of their processing plant in order to improve operational stability. One step towards this goal is the application of a Digital Twin concept to provide Virtual Instruments. Haile has engaged ANDRITZ to implement Virtual Instruments at their grinding area hydrocyclones and at their tailing thickener underflow pump. These virtual instruments provide density values in a traditionally difficult location for reliable slurry density measurement. The Digital Twin is a first principles IDEAS1 ™ simulation model, connected in real time to the control system. Results have been promising, with the virtual instrument values matching the physical instrument under normal operating conditions, and showing better prediction under upset conditions. Haile plans to use the virtual instruments as optional process control parameters. INTRODUCTION OceanaGold’s Haile Gold Mine is located near Kershaw, South Carolina, about 50 miles southeast of Charlotte, North Carolina. This location was first mined in 1827, and has produced gold through several operating periods since then, including a heap leaching operation from 1985 through 1992. In October, 2015, OceanaGold acquired Romarco Minerals, the previous owner of the Haile Operation. The current operation began in 2017 as an open pit mine with additional underground resources. The nameplate throughput is 6,350 tpd ore, and 2017 production was 118k oz gold, with 140 to 155k oz gold expected in 2018. Proven and Probable reserves exceed 3 Moz. The process, as shown in Figure 1, includes a primary jaw crusher, comminution with a Semi-Autonomous Grinding (SAG) mill and ball mill circuit, flash flotation, rougher flotation, regrinding, pre-aeration, carbon in leach (CIL) leaching, carbon elution and regeneration, cyanide recovery, electrowinning and refining. The Haile Operation’s inaugural gold pour took place January 20, 2017. Mine life is expected through at least the year 2030. Based partially on prior experience of some key OceanaGold personnel with automation services from ANDRITZ on other projects, OceanaGold decided to include ANDRITZ on the Haile project. The scope of these services for Haile included design and supply of the process control application software, an ANDRITZ dynamic process simulator for operator training, and ANDRITZ Advanced Control Expert (ACE) ®2 systems for the SAG mill, ball mill, and rougher flotation areas. Since startup, ANDRITZ has continued to provide services for the site, particularly related to PLC and HMI equipment, programming and support, ACE system expansion, and the implementation of Virtual Instrumentation. The implementation of this new Virtual Instrumentation technology at Haile is consistent with Haile goals: increased automation, a change in the role of the operator from interactor to monitor, and improved stability by removing human error.

Jan 1, 2019

By Daniel G. Ganey

Kerr-McGee Coal Corporation has used diesel face haulage and support equipment at its dual-seam Galatia Mine in Southern Illinois since production activities commenced in 1983. The mine began production from its lower seam, the Harrisburg No. 5 coal seam, in October 1983 and from the upper Herrin No.6 coal seam in April 1985. Before production began, the company developed a program designed to make use of the flexibility offered by diesel equipment. While productivity was an important goal, the top priority of the program was to provide a safe and healthy work environment for the miners. Management believed that high productivity would naturally follow. History has proven this belief to be true.

Jan 1, 1990

By T. W. White

One of the objectives of today's mine superintendent is to increase his equipment availability. To this end we have seen improved scheduling procedures, preventive maintenance programs and extensive drive training and operating procedures. However, until recently, one area that has changed little in the past twenty years is the method of refueling and servicing mine equipment. In looking at mines across the country continually one encounters the hazardous oil soaked ground, the hand held fuel nozzle and the maze of hoses of the "traditional" fuel stop. By adapting technology developed in the construction and aircraft industry, current fueling and servicing practices can be easily improved. The result will be less nonproductive time, less downtime from engine failures and increased security from major refueling fires. The time saved almost amounts to having another truck in the fleet! One feature of the improved servicing practice is the implementation of high flow fueling. For trucks now on the market, a flow rate between 120 and 150 gam is feasible, about 90 gam greater than current practice. This flow rate could be increased even further as larger trucks come into use. A second idea borrowed from the aircraft industry is the use of positive lock type connection nozzles that automatically shut off when flow stops. These may be used for fuel, water, oil and hydraulic systems to eliminate spillage and assure that clean fuel, oils, and water are delivered to the vehicles. The reduction of fuel spillage lessens the threat of major fires resulting: in equipment damage and loss. Eliminating fire hazards will become even more important as the turbine engine with its lighter, more volatile fuels come into common use.

Jan 1, 1972

By M. Duane Lackey

Electric drives hire done outstanding job in many-fields that are related to the mining industry. The equipment that is offered for electric-trucks was developed from the traction equipment which is used on the diesel electric locomotive. Rotating equipment available for use on electric trucks is identical in principle to that which is used on these locomotives. In as far as it is practical, similar controls are used. Another descendent of the diesel electric locomotive can be found in the oil well drilling industry, Here, locomotive traction motors and. electric controls have been modified to fit the particular requirements of the drilling industry, One 2400 H.P. diesel electric drilling rig drilled a 24,000 Ft. well in West Texas with an electrical maintenance cost in the order of 7¢ per hour This was a new rig and the costs are less than the average maintenance costs will be for the life of the equipment, Even soy since it took one (1) year to drill this well, this 7¢ per hour has real significance. Electric shovels use a similar type of electrical equipment; they too have shown real savings over the equipment they replaced. Since electric drives have done so well, in other fields, they warrant consideration for use in high horsepower, large capacity trucks.

Jan 1, 1961

By Donald M. Duncan

An acceptable source of concrete aggregate is available in Kansas City in a continuous, medium bedded, slightly dipping limestone unit. Removal is accomplished in shallow depth, 12 feet to 17 feet high, room and pillar mines. The accepted empirical design spaces 20 foot pillars 60 feet on center. A portion of the 20 foot unit is left in place for roof support. Rock and soil cover is variable to 100± feet maximum. Long-term stability of these mines is affected by numerous factors, including the above mine-rock profile, ground water conditions and mining practice. Crusher-run aggregate sells at the mine for $2.20 per ton, yielding a gross income of $2.00 to $2.80 per square foot of mine. Use of mine space for real estate development requires a new perspective in mine development. Mining practices to obtain long term stabile structures can become an over-riding factor as compared with minimum production costs and maximum extraction ratios. Poorly mined areas are unusuable for secondary purposes. Development cost for lease space in less desirable mines is substantially greater than those planned for a secondary use. Real estate development in mine space involves unique engineering problems. Properly engineered developments offer singular advantages. Warehouse lease space sells for $.50 to $1.00 per square foot per year; fully developed office areas may double these values.

Jan 1, 1968

By V. R. Burkhart

Pennsylvania Power & Light Company is an investor-owned public utility which was incorporated under the laws of the Commonwealth of Pennsylvania on June 4, 1920, with general offices at 901 Hamilton Street, Allentown, Pennsylvania. At the present time PP&L is operating five coal-fired steam electric stations, two hydroelectric stations and one steam heat plant which is being converted from anthracite to oil fired. In addition, PP&L is a partner in both the Keystone and Conemaugh mine mouth bituminous coal-fired steam electric stations in Central Pennsylvania and also part owner of a company which operates another hydroelectric station. PP&L plants, other than the two mine mouth stations, are located in Central Eastern Pennsylvania. (Figure 1) The company derives about 99% of its operating revenues from supplying electric service, while the balance is from the one steam heat plant serving the city of Harrisburg. The entire service area covering 10,000 square miles in 29 counties, has a population of approximately 2,300,000 people. The area served is mostly suburban. It includes 109 communities each having a population in excess of 5,000 people. The largest cities served are Allentown, Bethlehem, Harrisburg, Hazleton, Lancaster, Scranton, Wilkes-Barre, and Williamsport which range from 50,000 - 120,000 in population. So you see our service area does not include any major cities. The area has industrial, commercial, residential, agricultural and recreational activities that are linked with the Eastern Megalopolis by an extensive interstate limited-access highway system and railroad networks. We consider this Central Eastern Pennsylvania area we serve as the "heart of the market" -- an area with great growth potential.

Jan 1, 1973

By C. Clark, J. Seymour, D. Benton

"National Institute for Occupational Safety and Health NIOSH is conducting research on jackleg use and related accidents in underground metal mines. This paper provides an analysis and overview of jackleg drill usage, accidents, operational characteristics, and alternatives, based on information from injury reports, legacy research, stakeholder input, and published literature. Jackleg drills are involved in more ground fall accidents in underground metal mines than any other drill. Jackleg-related injuries are most prevalent at the face in the course of installing initial ground support. Alternatives to jacklegs for drilling and bolting under incomplete support in narrow underground openings are not yet available. Small mechanized bolting equipment needs to be developed to address jackleg-related accidents and improve safety at mines where jacklegs are being used. JACKLEG DRILL Description The term “jackleg drill” is a generic name for a class of handheld, rotary, percussion rock drills that are equipped with an attached reaction leg to provide stability and thrust for the drill (Figure 1). All of the drill and leg controls are located near the operator’s handle at the rear of the head portion of the drill. Jacklegs are classified according to the bore size of their pneumatic pistons which normally range from 6.03 to 8.26 cm (2.375 to 3.25 in) [Kurt, 1982; Clark, 2012]. Jacklegs typically weigh 460 N (103 lbs), but their weight can approach 535 N (120 lbs) after they are fitted for operation with drill steel and air and water hoses [McKibbin and Clark, 2001]. In underground mines, jackleg drills are commonly used to drill 3.8-cm (1.5-in) diameter holes 1.83 m (6 ft) deep in rock. Application The jackleg drill is primarily used in underground mines when the size of the ore body, the ground conditions, or the mining method do not permit large openings to be mined using mechanized equipment (e.g., narrow vein mining). Jacklegs are used to drill blast-holes for explosives and also holes for installing ground support. These versatile drills are used in nearly all phases of mining including exploration, development, production, and maintenance [Kurt, 1982; Williams et al., 2007; Chen and McKinnon, 2012]. The jackleg is used to drill holes in rock using drill bits attached to hollow steel bars called drill steels (rotary percussion drilling). After the hole is drilled, the jackleg can be used to install different types of ground support components, depending on the ground conditions and the specific ground support measures that are needed. For example, the jackleg can be used to install expansion-anchor rockbolts or resin-grouted rockbolts using the drill’s rotary-motion feature. On the other hand, the jackleg can also be used to install friction-type Split-Set™ rockbolts using the drill’s percussion (hammer-motion) feature. As shown in Figure 1, various washer-like bearing plates can be installed along with these bolts to provide additional ground support and to help secure surface control products, such as wire mesh and shotcrete that are in turn used to retain small, loose material between the bolts [Clark, 2012]."

Jan 1, 2016

By K. A. Perry, R. Q. Eades

The University of Kentucky conducted inerting tests and angle of ejection tests on three types of rock dust. A newly developed hydrophobic dust was compared against typical dry and wet dust applications. This new product is designed to alleviate respirable dust concerns for dry dusting and caking issues with wet dusting. Samples for both test types were prepared in a laboratory and subjected to temperature and humidity cycles that are typical of an underground coal mine. Inerting tests were conducted in a 38-L chamber with a 5-kJ Sobbe igniter. Angle of ejection testing was conducted at the University of Kentucky Explosives Research Team’s laboratory in Georgetown, KY. The results of these tests indicate that the newly developed dust has improved results for flame suppression and ejection compared with typical wet dust applications. The significance of these results is discussed with regard to existing respirable dust regulations and the issues associated with caking.

Jan 1, 2016

By O. K. Olawale, G. O. Edaogbogun, B. N. Ben‑Festus, F. Ben, F. R. Amodu

The environmental and health implications of artisanal gold mining activities at mining sites across Nigeria have rekindled research interest. This study aimed to assess the scalability of naturally occurring radioactive materials in gold mining sites in Iperindo, Nigeria. Soil samples were collected from three different mining sites and control locations and analyzed for natural radionuclides, mainly 238U, 232Th, and 40K, using gamma spectrometry having a sodium iodide detector. The average activity concentration values of 61.55 ± 3.71, 72.65 ± 4.45, and 1134.99 ± 38.12 Bqkg− 1 obtained from within the mining sites for 238U, 232Th, and 40K, respectively, were above the world permissible values of 33.0 Bqkg− 1 for 238U, 45.0 Bqkg− 1 for 232Th, and 420.0 Bqkg− 1 for 40K. The average activity concentration values of 15.26 ± 3.19, 21.46 ± 4.27, 381.04 ± 23.36 Bqkg− 1 estimated for 238U, 232Th, and 40K, respectively, for the control location were, however, lower than the global permissible values. The study also evaluated other radiological parameters such as radium equivalent, dose rate, annual effective dose rate, internal and external hazard indices, and alpha and gamma indices. The obtained values were 252.83 Bqkg− 1, 119.98 nGyh− 1, 147.15 mSvy− 1, 0.85 Bqkg− 1, 0.68 Bqkg− 1, 0.31 Bqkg− 1, and 1.89 Bqkg− 1 respectively. Except for radium equivalent, external and internal hazard risks, and alpha index, which were significantly lower than the recommended threshold, all other radiological parameters were higher than the recommended global limits. Moderate data reproducibility and a p-value of 0.000574 further reinforced the robustness and reliability of the results obtained in this study.

Feb 22, 2024

By Joel S. Leventhal

The roles of organic matter in ore deposits are complex and represent a specialized effort in the larger subject of the geochemistry of ore deposits. The organic carbon cycle can be considered with particular emphasis to ore deposits in order to understand the origin and genesis of the organic matter. Organic matter may play one, several, or none of the following important roles in the formation of ore deposits: leaching, transport, concentration, reduction, and precipitation of metals. For deposits that contain organic matter, detailed field relationships and laboratory characterization of the organic matter are required to make an ore deposit model that Includes the organic matter and specifies its role(s). Examples of the involvement of organic matter in several types of uranium deposits are contrasted as being direct or indirect, syngenetic or epigenetic, and necessary or unnecessary. Examples of organic matter in deposits containing gold and lead-zinc, and In metal rich shale are discussed with respect to ongoing work and critical questions.

Jan 1, 2013

By Donald E. Ranta

An ore zoning technique developed by Climax geologists during the past forty years has been used to contour drill-hole assay values on cross-sections for fourteen porphyry molybdenum deposits in western North America, including the Climax and Henderson orebodies. Detailed geological studies of these large, complex deposits are essential in determining ore controls, which are the factors most critical to the zoning of MoS2 assays and to conceptualizing geologic models. The technique provides a detailed representation of the size, shape, grade distribution, and geologic continuity of the individual deposits. It demands a disciplined approach and adheres to rigorous rules while maintaining flexibility for adaptation to widely varying geologic conditions. By defining the limits that guide and control manual, computer-assisted conventional, and geostatistical reserve estimates, it exerts a strong geologic influence on the estimation process. A combination of ore zoning and geostatistical analysis of molybdenum deposits produces a significantly more accurate, precise, and defendable geologic reserve estimate than other methods.

Jan 1, 1983

By Brian Y. Lattimer, Kray D. Luxbacher, Jonathan L. Hodges, Manuel J. Barros-Daza

The abstract discusses the importance of predicting fire response time (the time before conditions become untenable for firefighters) in underground coal mines. It introduces a data-driven approach using artificial neural networks (ANNs) to predict response time and fire size based on measurable parameters like CO concentration, mine geometry, air velocity, and time since fire detection. The approach was tested using simulations from fire models (FDS and FSSIM), showing promising results for real-time predictions during mine fires.

Mar 6, 2022

By Robert F. Shurtz

This paper suggests that pre-occupation with the random process model notised by geostatisticians may result in neglect of more promising techniques, especially since the random process model does not appear to be essential to current geostatistical procedures. This point of view is emphasized pictorially. To emphasize the potential of new techniques a simple application of the conventional Brownian function is described. The probabilities estimated in this truly random way are different from those estimated by Kriging

Jan 1, 1980

By T. S. Golosinski

This paper identifies the components of belt conveyor shifting force as a vertical force. Pv, horizontal force, Ph, and longitudinal force, P1. A method for estimation of these forces is proposed, which relates their value to the properties of the conveyor structure and rails, shifting operation parameters, and other site-specific conditions. The effect of this force on shifter behaviour is analysed and guidelines are developed for selection of a suitable shifter. Also discussed are the requirements of the shifting operation for other equipment.

Jan 1, 1986

By Thomas H. Dubaniewicz

(XP) enclosures to enclose electrical ignition sources to prevent propagation of an internal methane-air explosion to a surrounding explosive atmosphere. Researchers at the National Institute for Occupational Safety and Health (NIOSH) conducted a lithium-ion battery thermal runaway test within a modified MSHA-approved XP enclosure to assess thermal runaway containment. Thermal runaway produced jet flames emanating from the cover joint at several locations and distorted the cover joint and bottom plate of the enclosure beyond allowable limits. The test demonstrates that XP enclosures may not provide adequate explosion protection against lithium-ion battery thermal runaway. This paper suggests some approaches to mitigate the hazard.

Feb 1, 2024

By R. J. Matetic, J. Noll, C. Zhou, J. DuCarme, M. Reyes, J. Srednicki

"In April 2016, MSHA began requiring the use of continuous personal dust monitors (cPDMs) to monitor and measure respirable mine dust exposures to underground coal miners. After the cPDM’s implementation, mine operators discovered that it interfered with proximity detection systems (PDSs), thus exposing miners to potential striking and pinning hazards from continuous mining machines. NIOSH was sought out by MSHA and mining industry stakeholders to determine how the cPDM and PDS interact with each other. Accordingly, NIOSH investigated existing standards, developed test protocols, designed experiments, and conducted lab evaluations. Some interferences were observed to be caused by electromagnetic interference (EMI) from the cPDM. Results showed that there was no significant interference when the cPDM and the miner-wearable component of the PDS were separated by distances of 6 inches or greater. In this study, the cPDM and PAD needed to be at least 6 inches apart in order for them to be used simultaneously and reduce interference potential. INTRODUCTION Underground coal miners are exposed to a variety of hazards on a daily basis such as coal dust exposure, high noise levels, roof and rib falls, the potential for fires and explosions, and operating and working with heavy machinery. One of the hazardous jobs is operating or working nearby a continuous mining machine (CMM). According to Mine Safety and Health Administration (MSHA) statistics, 40 miners have been fatally struck or pinned by a CMM since 1984. In an effort to prevent future striking and pinning fatalities from occurring, proximity detection systems have been developed and are required on all operating CMMs in underground coal mines, with the exception of full-face CMMs, by 2018 (1,2). Proximity detection systems (PDSs) are designed to alarm miners and stop machine motion in order to protect miners from being struck, pinned or crushed by CMMs(3). Currently, MSHA-approved PDSs, installed on CMMs, are based on the principle of magnetic flux density (B-field) (4,5). The system generates a magnetic field around a CMM and determines the relative distance a miner is from the CMM based on a detected magnetic flux density. A PDS typically consists of multiple magnetic field generators mounted at different places around the CMM, and personal alarm devices (PADs), which are worn by the miners to detect the magnetic flux density. When a miner, wearing a PAD, gets closer to the machine, the PAD detects a stronger magnetic field from the generators and detects a weaker magnetic field when a miner moves away from the machine. The magnetic field generators installed on CMMs typically produce modulated magnetic wave signals at frequencies between 10 kHz and 120 kHz. The magnetic fields are measured by three small magnetic coil antennas mounted on orthogonal axes inside of the PAD worn by the miner. According to Faraday’s Law, the changing magnetic field induces a voltage in each coil antenna, and the voltage values are transmitted from the PAD back to a controller on the CMM wirelessly, typically at a frequency between 400 MHz and 2.5 GHz. These values are then used to determine the distance between the miner and the generators of the machine. Typically this information is used to determine when a miner wearing a PAD is in a warning zone or stop zone which would trigger different alarms and actions such as slowing the machine down or stopping it."

Jan 1, 2017

By W. R. Reed, D. E. Pollock, T. W. Beck, J. A. Organiscak, J. D. Potts

In underground continuous mining operations, ventilation, water sprays and machine-mounted flooded-bed scrubbers are the primary means of controlling respirable dust exposures at the working face. Changes in mining arrangements — such as face ventilation configuration, orientation of crosscuts mined in relation to the section ventilation and equipment operator positioning — can have impacts on the ability of dust controls to reduce occupational respirable dust exposures. This study reports and analyzes dust concentrations measured by the Pittsburgh Mining Research Division for remotecontrolled continuous mining machine operators as well as haulage operators at 10 U.S. underground mines. The results of these respirable dust surveys show that continuous miner exposures varied little with depth of cut but are significantly higher with exhaust ventilation. Haulage operators experienced elevated concentrations with blowing face ventilation. Elevated dust concentrations were observed for both continuous miner operators and haulage operators when working in crosscuts driven into or counter to the section airflow. Individual cuts are highlighted to demonstrate instances of minimal and excessive dust exposures attributable to particular mining configurations. These findings form the basis for recommendations for lowering face worker respirable dust exposures.

Jan 1, 2016