Search Documents

By Franklin B. Woodbury

As part of its goal of helping maintain an adequate supply of minerals to meet national economic and strategic needs, the U.S. Department of the Interior's Bureau of Mines is evaluating alternative technologies to treat oxidized taconites. Since process control is an essential element in the application of these process technologies, research was performed with a prototype monitoring system. A Californium-252 neutron source and a thermal neutron capture- gamma ray spectra analysis method was utilized to measure the amount of iron and the percent solids in the process slurries. The concentrate and tailing streams in a 410-kilogram-per-hour (900- pound-per-hour) pilot plant employing a selective flocculation and cationic flotation process were monitored. The results obtained showed that the thermal neutron capture-gamma ray reaction can be used to provide process control parameters.

Jan 1, 1979

By Y. C. Kim, M Nataraja, J. T. Buckley, D. H. Tiktinsk

The Nuclear Waste Policy Act of 1982 (NWPA) assigns the U.S. Department of Energy (DOE) the responsibi1it.y of locating, constructing. operating, closing and decommissioning a nuclear waste repository. Prior to submittal of a licensee application to the U. S. Nuclear Regulatory Commission, the DOE is required by 10 CFR part 60 to conduct a program of site characterization for the site to be described in such application. Site characterization includes an exploration and research program in the field and laboratory to determine the geologic conditions and ranges of those parameters which are necessary for determining the suitabi1it.y of the site as a geologic repository. The information thus collected should be able to establish with reasonable assurance that the public and environment will be adequately protected from the hazards associated with a repository at the site. This paper demonstrates by example a geostatistical approach which, on the basis of the existing limited data base, can be used to evaluate (1) whether existing information on a certain parameter is adequate to be considered representative. (2) if additional information is required, where should the additional sampling or testing be performed, and (3) whether the new1.y acquired data along with the existing information constitute representative data.

Jan 1, 1986

By M. C. Rockwell

There are approximately 1,800,000 t of discarded dolomitic-limestone tailings from the Gays River lead/zinc mining operation in Nova Scotia. Neutralization effectiveness similar to an agricultural grade limestone and low contents of residual metals make the tailings a suitable source' of soil conditioner material for the local market. However, the fine particle size, 98% passing 147µm, and a high moisture content make their handling and application difficult. Agglomeration of the tailings into relatively small hard pellets was investigated and difficul¬ties were overcome. Pellets with a range of pH values and various amounts of soil nutrients and moisture content less than 10% were obtained, from tailings containing 20% initial moisture, through the addition of less than 15% selected materials.

Jan 1, 1985

By Tim O’Neil

Dressed in black tie and Victorian attire, some 200 people came to Leadville, CO, for a September weekend featuring a National Mining Hall of Fame and Museum (NMHF&M) induction banquet and a scenic mountain train trip to Fremont Pass and the Climax Mine. The 18th annual induction banquet on Sept. 17 began with cocktails and a open house. It was a chance for visitors to tour the National Mining Museum including the new Hennebach Wing, opened in February. The new wing is named in honor of Ralph Hennebach, retired chairman of Asarco. Formerly Leadville Junior High School, the Hennebach Wing encompasses more than1,440 m2 (15,500 sq ft) of floor space in two stories. One prominent feature is a 1923 Wills Sainte Claire touring sedan. Climax Molybdenum donated this first all-molybdenum steel motorcar. Docents were available throughout the museum to give banquet attendees directions and answer questions.

Jan 1, 2005

By David A. Brence, Andrew D. Marti, Richard P. Stahura, Ronald J. Valentine

The development of an effective belt-cleaning system for a new conveyor system seemed a fairly conventional assignment. But a closer examination of the project showed a number of “fine print” details: •High altitude location (with resulting cold weather and low humidity conditions). •Long conveyor length. •Troublesome material (very sticky and capable of hardening like concrete). •Limited water. These difficulties are spelled out the challenge of developing a cleaning system for the production conveyor2 (PC2) belt at Climax Molybdenum’s Henderson Mine.

Jan 1, 2005

By Wayne A. McCurdy

I welcome the opportunity to meet with you and discuss the work and program of the Office of Coal Research. Our programs are oriented to serve the conservation objectives of the Johnson Administration and of the Nation by seeking out the most efficient and best uses for coal. We believe that even if only a portion of our program is successful, the coal industry and the Nation will benefit far out of proportion to our expenditures. Operating with a budget of $7,220,000 in Fiscal Year 1966, OCR sponsors contract research which offers potential for achieving benefits to the coal industry in the form of new production and new markets. This directs us into many areas of research activity: in coal combustion, in advancements in mining methods and coal preparation, in new uses for coal, and in associated economic and marketing research.

Jan 1, 1966

The introduction of computer technology to the mining industry has produced many benefits for the mining engineer. The most significant is the dramatic increase in productivity realized by the individual user. This is important during times of competitive market conditions. Software for the minerals and energy industries has evolved substantially over the past decade. But even today it remains difficult to find a system that features the flexibility and integration capabilities to effectively (and cost-effectively) handle the needs of professionals in each phase of the mining industry - from exploration to reclamation. Several national software developers are now addressing this challenge. One Denver-based company, MINEsoft Ltd., offers a software package that is currently being used in each phase of the mining industry. The basic technology used in MINEsoft's database management system was developed in the 1960s. But during these early years of the computer industry, most of the technology was available only on mainframe computers, and then only as separate entities. MINEsoft's system unifies these various systems in one package that can be used on most computers manufactured today. Database Management System TECHBASE is a flexible, integrated database management system designed specifically for technical applications. The system features a database manager with no practical limit to the amount of data it can store, retrieve, and manipulate, according to the company. TECHBASE in¬cludes Applications Packages (TAPs) designed to meet the needs of professionals in a host of industries. Clients use the TECH BASE system to prepare many reports, including important EPA information. The package reduces data to a manageable level and enables users to increase productivity with a smaller staff. Mining engineers no longer need to do things by hand. What used to be a day's work can be accomplished in an hour or two. Exploration "Using the TECHBASE system to generate maps has probably saved us the expense of three or four draftsmen," says Ralph Fitch, regional manager and senior staff geologist with Chevron Resources in Portland, ME. "The system has great flexibility. You can treat it much like a spreadsheet. If you are halfway through with a particular project, the system allows you to add fields and calculations with ease but without starting over." Fitch uses TECHBASE for the "straightforward" plotting of results and generation of geochemical and geophysical profiles. "In exploration," he says, "these are the two key elements ... the generation of maps and data profiles. The system allows you to plot as many elements and variables in these areas that you like." Other aspects are important, too, says Fitch, including drill hole sections. "We use all the basic capabilities the system provides in the complete package," he explains. "When shopping for a system, TECHBASE was clearly dedicated to exploration in the

Jan 9, 1987

By Dean Brox

The use of Tunnel Boring Machines (TBMs) for tunnel construction of long tunnels in the Andes of South America has been of mixed success in the past due to a variety of reasons and key lessons can be recognized. A review of past TBM tunnel projects in the Andes has unveiled some interesting findings for different TBM tunnel approaches with both world records of progress as well as nearly in-completed projects with machines being abandoned. Key considerations for the use of TBMs for tunnel construction in the Andes include geological issues; (faults, rock type, rock strength, rock abrasivity, durability, groundwater inflows),depth of cover and the potential for overstressing/rockbursts, site access and terrain, portal locations, intermediate access possibilities, minimum tunnel size, support requirements, contractor and labour experience, and project schedule demands. TBMs offer highly recognized schedule benefits(high progress, no concrete lining) for a project if intermediate access adits are limited as well as hydraulic benefits for water conveyance projects. Minimum specifications for TBMs can be easily developed to suit the unique requirements of any project so as long as all factors are carefully considered. The overall conditions and factors associated with some projects may suggest that it is not appropriate to use TBMs due to a perceived high risk. Finally, access for geotechnical investigations by drilling in the commonly steep terrain of the Andes is typically difficult and often not impossible. Alternative approaches for geotechnical investigations for TBM tunnels including comprehensive mapping, high-resolution airborne electric-magnetics for delineation of possible fault zones, and rock block sampling is presented and discussed.

By Verya Nasri

The Silver Line Phase III Project is the final one mile underground segment of the new Bus Rapid Transit in downtown Boston. The project is expected to significantly reduce existing and anticipated traffic congestion. The twin one-lane tunnels and two station platforms will be built by NATM in Boston saturated soft clay, sand and till layers in proximity to several historical buildings, underpinning two existing cut and cover subway stations and several major utilities in densely built urban area. This paper presents the analysis and design of the NATM tunnels and stations detailing the excavation sequence and support system and various ground improvement and pre-support techniques used in the preliminary and final design of the project

By Martin C. Jones

INTRODUCTION This paper outlines the methods used to drill and pregrout prior to the excavation of five Mine Shafts in the Coal Measures of the Eastern United States. One example is the use of cement pregrouting of four 240 meter deep shafts and the second is the use of chemical pregrouting of a 360 meter deep shaft. These two examples will be compared and contrasted, both at the investigation stage of each project, and during the drilling and pregrouting itself, to illustrate the different approaches taken and how these affected the outcome, both technically and economically. INVESTIGATION FOR 240 METER SHAFTS In the case of the four 240 meter shafts, site investigation was carried out prior to bid, and information was made available by the Client in the form of a report. This report was based on pressure testing of NQ cored boreholes at each shaft site. Pressure testing was repeated two or more times, at each test setting, using 345 or 690 kPa of water pressure in accordance with the procedure outlined by the U. S. Bureau of Reclamation. Flow readings were taken every minute over a period of ten minutes. Maximum computed permeabilities, for the strata which accepted water under test for the shafts, carried between 1.0 x 10-6 m/s and 3.0 x 10-6 m/s, and total calculated seepages varied between 170' litres/minute to 3891 litres/minute. Although these figures did not indicate an excessive amount of seepage, the Client decided that pregrouting should be carried out, and chemical grouting was not discussed, even though the test permeabilities indicated the use of cement grout would be limited in this case.

Jan 1, 1979

By Iwasaki I.

This article discusses the effect of physical and chemical modifications of starches on the anionic and cationic flotation of silica from oxidized iron ores and magnetite-taconite concentrates, and the results of the interaction of starch, pH, and calcium ions on the flocculation, clarification, and filtration of iron ore slimes and magnetite-taconite tailings. Starches, particularly when anionically modified, were found to be effective depressants in anionic silica flotation. British gums and dextrins were beneficial for oxidized iron ores, but none of the starches or starch derivatives appeared to have any effect on magnetite-taconite concentrates. The flocculation and filtration of iron ore slimes were most strongly affected by the level of starch, to a lesser degree by the pH, and were virtually independent of the level of calcium chloride. The clarification of iron ore slimes was complexly dependent on these three factors. The flocculation of magnetite-taconite tailings depended mainly on the level of starch, whereas their clarification depended on the level of lime. As previously reported in the literature, selective flocculation and partial upgrading of a semi-taconite could be readily attained with starch and calcium chloride.

Jan 1, 1968

According to the previous research, it is found that the thickness of cover is mostly less than 100 m for highwall mining system. However, for most of the Chinese surface coal mines, the mining depth is over 150 m; on the other hand, the shovel-truck is the most common mining technology. As a result, a lot of residual coal will be remained around end-walls. Considering these facts, the calculated methodology of highwall mining system under thick cover is presented in this paper. Meanwhile, numerical simulation of highwall mining system under thick cover was carried out. The outcome shows that the calculated methodology for pillar stability of highwall mining system under thick cover presented in this paper is acceptable. In other words, the highwall mining system is feasible to extract the residual coal around end-walls in Chinese surface coal mines. Thus, not only coal recovery ratio can be improved, but also can increase the production life of surface coal mines in China.

Jan 1, 2012

By L. C. Lang

Effective and profitable mining begins with good blasting results. While the importance of sufficient energy to break the rock is recognized, more attention should be paid to the time factor in blasting. Fragmentation, looseness and the shape of the muckpile can be improved and energy levels lowered through the use of proper delays. The long delay is also the most important parameter in establishing stable walls along the final limits of the pit. The time factor in blasting is explained through the rock acceleration process and its practical application is demonstrated by case histories.

Jan 1, 1981

By A. Martin

Detailed porewater profiles of arsenic and other interstitial metabolites were used to assess the relationship between trophic status, sediment redox chemistry and arsenic mobility in a historic tailings repository. The results demonstrate that in eutrophied systems which exhibit greater sediment oxygen demand, the depth of the Fe(III) redoxcline, and hence depth of arsenic release, may lie in close proximity to the sediment-water interface. As a result, arsenic scavenging mechanisms are significantly reduced, resulting in a greater flux of arsenic to the water column. Such considerations have important implications for the management of pit lakes, tailings ponds and contaminated lakes which may consider: 1) the discharge of sewage to the water body during operations; and/or 2) post-closure fertilization as a remediation strategy.

Jan 1, 2002

By Tevfik Güyagüler

Airborne dust is one of the important environmental problems in mines. Besides conventional dust control methods, recently, extensive studies have been carried out on the elimination of dust before it has actually been formed. Determining to what extend rock characteristics influence the amount of dust produced during different mining activities are considered as a guide for this purpose. The factors analyzed in this study were main mechanical, physical properties and petrographical constituents, namely free and combined silica. In the study regression analysis techniques were applied to investigate the effectiveness of aforementioned factors. INTRODUCTION Nearly every aspect of mining activity contributes to the air pollution caused by dust. Therefore the harmfull effect of airborne dust has been investigated many years and limit dust concentration levels were determined for various types of mine dust. To keep the dust level below limit value different dust control techniques have been applied in mines. So far, the well known techniques regarding dust control focuses on reducing the amount of airborne dust. However, recently various studies have been carried out to avoid the dust before it has actually been formed (Bhaskar and Gong, 1991). In this respect, influence of rock characteristics on dust formation is regarded as a guide for this purpose. The present contribution describes such a study in which the drilling operation is considered as the source of the dust. In this study drilling and dust sampling process were undertaken in a model gallery that simulates an underground working. The mechanical and physical properties of the rock samples were measured in rock mechanics and ore dressing laboratories. Quartz and combined silica contents of the rock samples, on the other hand, were determined in the laboratories of geological engineenring department. Rock samples used in the research were different types of coal measure rocks, namely, sandstone, shale and conglomerate. The rock characteristics studied in this work are brittleness, toughness, rock strength, hardness and hardgrove index as inherent properties; free silica, and total silica contents of rock samples as petrographical constituents. Although there have been various studies to determine the effect of rock characteristics on the dust formation, still the type and extend of effectiveness have not been understood clearly. LITERATURE REVIEW Most of the studies investigating the effect of rock properties on dust formation concluded that they are effective. In such an investigation, it has been found that inherent rock properties influence dust formation (Das, 1973). In the another study, dustiness of the air was considered as a function of the composition, hardness and moisture content (Panov, 1967). It was also accepted that in a drilling operation more fine dust is produced if the rock to be drilled is hard (Skochinsky and Kamarov, 1969). In some other investigations dust production were considered as a function of hardgrove index (Moore and Bise, 1984) or formulated in terms of brittleness, toughness and hardness (Güyagüler, 1991). The effect of the petrographical properties of coal or rock on dust formation characteristics have also been studied (Baafi, 1979) (Panov, 1967). Because of its importance, various researches were conducted the study to find out the effect of free and combined silica content of dust on dust formation. In one of the study, the relationship between quartz in the coal seam and quartz in the airborne coal dust was investigated (Ramani et al, 1988).

Jan 1, 1993

The 22nd Annual American Mining Hall of Fame Awards Banquet sponsored by the Mining Foundation of the Southwest will be held at the Westin La Paloma in Tucson, AZ on Saturday, Dec. 4, 2004. This year’s inductee, guest of honor and featured speaker at the banquet will be J. Steven Whisler, chairman and chief executive officer of Phelps Dodge. Whisler is also a director of Phelps Dodge, Burlington Northern Santa Fe, America West Holdings, the National Mining Association, the International Copper Association and the Copper Development Association.

Jan 1, 2004

By S. Strömberg, A. Jokilaakso

Two complex copper concentrates and one arsenical nickel concentrate were oxidized in simulated flash smelting conditions using a laminar-flow furnace. The concentrates contained tetrahedrite as Sb-bearing mineral and arsenopyrite and gersdorfite as As-bearing minerals. At high temperatures and low oxygen potentials, Sb tended to vaporize, but with high oxygen potentials it was captured in mixed oxide phases with copper and iron. Arsenic was found to follow antimony in copper concentrates, although with less sharp contrast between low and high oxygen potentials. In the nickel concentrate studied, arsenic was found to vaporize from the gersdorffite particles and, subsequently, condense on the other particles.

Jan 1, 1998

By Troy Holm, Matthew L. Fuller, Frederick H. Earnest

Virtual Reality Animation Of The Proposed El Dorado Mine In El Salvador Assists Regulators In Reviewing An EIA

Jan 1, 2005

By Enrique Rubio Esquivel, Matías Fuentes Bustamante

The transition from open pit to underground mining represents a key strategic challenge in modern mine planning. This paper presents a multicriteria and multivariable methodology to plan such a transition, integrating technical, economic, environmental, and social considerations. The proposed framework focuses on risk reduction (de-risking) through the identification of alternative development paths, the use of stochastic simulation to model geological and technical uncertainty, and different mining strategies such as methods, production rates, sequence, etc. for ultimate underground implementation. The study summarizes the limitations of traditional planning methods—which usually treat the open pit and underground mine designs as independent processes—, also often it considers a single mining method and production rate for the underground option. Instead it is proposed an integrated approach that leverages synergies between both mining methods and scalable production rates. Also the proposed methodology incorporates the definition of critical variables (geotechnical, economic, and social, among others), the construction of multiple operational and technological transition paths, and the evaluation of each path under criteria of economic attractiveness and practical do-ability (capacity to be executed). Using simulation tools (SIMPLAN for operational performance and SIMVAL for economic evaluation), probabilistic distributions of the different path are obtained, enabling the quantification of the project’s Value at Risk (VaR). A subsequent multicriteria analysis weights the expected profitability against the feasibility of execution of each alternative, producing a decision matrix that provides a framework for evaluating the different project path. As a result, the proposed approach identifies OP→UG transition strategies that maximize business value by capturing remaining resources while minimizing financial and operational risks. Finally, strategic conclusions and recommendations for the industry are provided, emphasizing the importance of early transition planning even challenging the open pit sequencing of the latest push backs by introducing early underground operations. Future work includes strengthening the methodology—such as integrating real-time analysis and adaptive decision-making—and providing recommendations for its application in various mining operations. In summary, this paper delivers a technical and professional framework to guide mining companies on when and how to carry out a successful transition from open pit to underground mining, balancing resource recovery with financial, operational, and social security.

Feb 22, 2026

By B. Farshadi, B. Asi, M. J. Habibian

"In this paper, the most significant environmental aspects that are identified in the Taft Copper Project (TCP) are the quality and quantity of water, pollution of the existing watercourses and post-mining land use, matters such as air and noise pollution are deemed to be of less significance. Analysis has been performed for Do Nothing Alternative, Pre-stripping Phase, Mining Phase, Closure and After-use Phases. Analysis of the environmental assessment of TCP was carried out in three stages. In the first stage, the general negative and positive aspects of the project were identified. In the second stage the intensity, magnitude and significance of the environmental impacts of the project were identified. The third stage is related to the final conclusions of the assessment team and the relevant reasoning. A modified Leopold Matrix was adopted for evaluating the significance and magnitude of the environmental impacts. For this project, the matrix was modified to allow the assessor to take account of negative and positive numbers."

Jan 1, 2011