Search Documents

By Xiaohong He, Qing Yu, Kaixiang Zhang, Rui Guo, Minghua Lin, Haoyu Miao

With the increasing depth of coal mining, the coal mine shaft traverses’ strata conditions become more and more complex. Shafts are often located in deep thick strata with unstable aquifers, and coal mining requires short-term rapid drainage of aquifers; the additional stress caused by aquifer water drainage is the direct cause of the shaft-lining failure. Over the years, many experts have conducted research on the shaft-lining damage caused by the consolidation and subsidence of the soil layer induced by the long-term drainage of the aquifer. On this basis, this paper conducts an in-depth study of the dynamic change of the pore water pressure of the aquifer in the short-term drainage and its influence on the response of shaft-lining strain and surface subsidence. The result shows that the Mandel effect of pore water pressure around the shaft-lining is obvious at the beginning of drainage, and the pore water pressure suddenly increases; the increase is independent of the drainage rate, which leads to the sudden increase of the shaft-lining strain value unrelated to the drainage rate. The result also shows that with the gradual dissipation of pore water pressure, the increase of shaft-lining strain is positively related to the drainage rate and negatively related to the drainage distance, and the variation trend of horizontal strain is greater than that of vertical strain, which appoints the main cause of shaft-lining damage.

Mar 16, 2023

By B. L. Bobo

To ensure the continued growth and economic viability of the Western coal industry, both in the domestic and inter- national markets, it is essential for the industry to become more creative and active in confronting the most serious obstacle in this objective; and that is, the inherently long distances which Western coal must be transported inland to reach its major markets. Figure 1 shows the 1982 coal consumption by state for those states where Western coal was consumed. (Except as noted in this paper, Western coal producing states are defined as Colorado, New Mexico, Arizona, Utah, Wyoming, Montana and North Dakota. Any exceptions used will have only an insignificant effect on the content of the paper). This figure illustrates the long distances that are required for Western coal to reach its markets. The total production for 1982 from the Western coal producing states was approximately 220 million tons, of which only 85 million tons was consumed within the boundaries of these states. The remainder was transported to markets outside the area. This map also shows, based strictly on the consumption of the states to which Western coal was shipped during 1982 and not considering other factors which are involved in the marketing of coal, the total market potential of Western coal would amount to a total of 445 million tons. This does not include export coal from the West Coast, which is now estimated to be less than 2 million tons for 1983. In 1980, it had been estimated that by 1985 the West Coast exports would have been at least 10 million tons per year, which will not be attained.

Jan 1, 1983

By Frank P. Frandina, Michael J. Loehr, Paul E. Gabryszak

The Heartland Corridor Clearance Improvement Project is part of a regional Public-Private initiative to allow double stack container trains a direct route from the Port of Norfolk through Virginia, West Virginia, Eastern Kentucky and into Central Ohio. In the Preliminary Engineering stage, 30 existing tunnels were assessed and 28 were found to need clearance improvements to allow the use of double stack trains. Alternative tunnel enlargement methods were developed to achieve the desired clearance improvements, while maintaining structural integrity and minimizing disruption to train traffic. This paper summarizes the geometric and condition investigations of the existing tunnels, as well as describes the preferred methodologies to achieve the desired clearance. The clearance improvements will be implemented beginning in the summer of 2007.

Jan 1, 2007

By K. Park

Coupled influence of sulphidizers and xanthates on the electrokinetic property and flotation behavior of malachite was systematically examined via electrophoretic mobility measurements and microflotation tests. The electrophoretic mobility results for the malachite before and after surface modification with different types (Na2S and (NH4)2S) and amounts (1×10-7?1×10-4 moles/g) of sulphidizers, showed that the isoelectric points (IEP) of malachite differed at the low dosage level depending on the type of the sulphidizer, which ranged between 5 and 9.5. However, the IEP values were observed to be shifted from high to low pH values with increasing amount of sulphidizers and finally ranged between 3 and 4, indicating that the sulphidizers played a different role on changing the surface property of malachite. In order to further understand the effect of sulphidizers on the electrokinetic property and flotation behavior of malachite in a sulphidizer+xanthate system, flotation tests were carried out with malachite sulphidized with Na2S and (NH4)2S (adsorptive amount=8×10-5 moles/g) at different bulk xanthate concentrations. The results showed that the flotability of (NH4)2S-treated malachite was greater than Na2S-treated one over the entire xanthate concentration investigated, indicating that the type of sulphidizers played important role in malachite flotation; however, no obvious correlation between electrokinetic property and flotability of malachite was observed.

Feb 27, 2013

By R. A. Reiley

Introduction Democratic countries are founded on the principle that all citizens have the right to participate in policy setting and decision-making processes. Citizen participation is especially evident in environmental issues and policies. In the United States, there are currently over 10,000 environmental organizations and new ones are being formed each year. Many of these organizations are formed on a watershed basis and are particularly concerned about the impact mining has on the environment. While the environmental issues vary from area to area, most concerns center around mining impacts related to subsidence, water pollution, and water diversion. Citizens have a number of avenues for participating in lawmaking that affects the mining industry. Some of these avenues include participation in litigation and citizen ballot initiatives. In addition, there are less formal methods of participation that include attending public meetings, commenting on agency rules or lobbying on specific legislation. The intent of this article is outline the various public participations mechanisms, highlight the latest legal developments that have affected mining industry through citizen participation, and briefly discuss emerging issues.

Jan 1, 2001

By Boghani. A. B.

A computer program has been developed to simulate evacuation of a mine in various configurations. The simulation input variables include characteristics of the mine, expressed, in the form of a network of passages, properties of hoists and hoisting strategies, initial miner positions, ventilation and compressed air velocities, stench warning system and self rescuer capabilities. The simulation can be carried out for cases in which there is no fire, i. e. , fire drill simulation, or for cases in which there is a fire at any arbitrary location. The fire is assumed to generate gases which impede movement of miners in the gaseous region. However, the thermal effects of the fire are not considered. The simulation output include the evacuation time for each miner, movement of the hoists, propagation of smoke through the mine passages and smoke exposure of the miners. Several illustrative simulations have been carried out to verify validity of the program and to demonstrate its capabilities. The computer program has been able to predict evacuation time, within 5 percent, for an actual fire drill. It is believed that this program can be used to evaluate evacuation performance of a mine, identify problem areas and demonstrate improvements due to the recommended corrective actions.

Jan 1, 1977

By C. C. Hamilton, G. R. Lane

Traditionally, mineral sands are evaluated by preparing several mineral products using a combination of heavy liquid-, magnetic-, and electrostatic methods. Whole-rock assays (WRA) are then conducted on ilmenite, rutile and zircon products in order to determine trace element contents, which may affect project feasibility. Combined methods can be time consuming, expensive and even outdated due to the use of banned and toxic chemicals such as clerici solution. Coupled with large field-sample quantities, these procedures can potentially introduce unacceptable sampling and related errors. Modern mineralogical analysis techniques can provide complete mineralogical inventories on a single THM product, reducing the amount of processing involved in satisfactory characterization of early exploration samples. A small exploration sample can be processed to produce a small THM concentrate using readily available gravity/density methods. In turn, the THM product is submitted for Whole Rock Analysis (WRA) and mineralogical inspection by X-ray diffraction (XRD), and microscopic evaluation. Modal mineralogy and textural data can be determined using optical methods, automated image analysis, and scanning electron microscope (SEM) based systems. Benefits of automation are reproducibility and the capability of rapidly analysing thousands of particles as opposed to manual optical methods. Automated systems include the use of Automated Digital Image Analysis (ADIS), and SEM-based systems such as the Mineral Liberation Analyser (MLA) and QemSCAN. For detailed mineral chemistry, microanalysis techniques ranging from electron microprobe (EMPA) to Secondary Ion Mass Spectrometry and Laser Ablation Mass-Induced Coupled Plasma-Mass Spectrometry (LAM-ICP-MS) are used. Examples of these automated and analytical methods are presented. ADIS at SGS-Lakefield Research uses optical characteristics to identify and measure mineral species in THM samples; rutile, pseudorutile, ilmenite and leucoxene can be distinguished. Analysis of a single THM product provides bulk modal mineralogy and grain size distribution of particles and the individual mineral grains. Textural information is also obtained detailing mineral associations as well as degree of alteration. Where textural and chemical resolution renders mineral identification ambiguous, SEM-based methods offer better resolution. Examples of this ambiguity are shown in this paper, which leads to QemSCAN as the preferred method where within-grain variability is concerned. Sampling and measurement strategies are followed to meet study objectives, providing a value-added framework for a sequential, cost-effective strategy, which will meet due diligence and bankable accreditation criteria. Studying a THM product by electron microprobe and LAMICP-MS may reveal potential fatal flaws related to mineral chemistry. Low detection limits in the range of 200 to 500ppm are possible using electron microprobe analysis for suitable matrixes (U, Th in zircon). For the detection of ultra low level elemental contaminants, LAM ICPMS is the most accurate method of evaluation. Elements including U, Th, La, Ce, Nb, and V in Ti-minerals can be determined down to 50 ppm.

Jan 1, 2005

At present, discounted cash flow analysis is generally accepted as the preferred method of valuation of mine projects in surface coal mining. One of the major reasons for that is its ability to take into account the time effect of money over the life-of-mine. As a looking-forward method, it requires forecasts be made with regard to economic, technological, technical, geological, and environmental conditions that will prevail in the future. All forecasts are inherently uncertain as they are a function of the uncertainty of all variables of the discounted cash flows analysis. This indicates that the only alternative for modeling the uncertainty in the project evaluation is the development of adequate risk models to serve the decision-making process. The paper offers a model of project cash flows at risk in strip coal mining, which is an integrated corporate risk management solution. The model is based on a stochastic approach that provides the answer to the question about how large is the deviation between stochastic cash flows and the planned value (or that used in the budget) at each time step of the discounted cash flows analysis, that is due to the uncertainty in the model variables. A solution is worked out for the allowable range of the stochastic cash flows variation that determines the probability of achieving the planned value of a mine project. The Monte Carlo simulation technique is used to model the stochastic behavior of the project variables. A case study of an opencast coal mine project is provided to illustrate the applicability of the risk model. The results obtained provide a new understanding of the mine project risk as a component of the project discount rate.

Jan 1, 2006

By R. W. Salmi

The authors discuss the cooperative efforts by Minnesota Ore. Operations and Research; from the earlier development, testing and installation of fine shear screens in the Minntac Step III concentrator to the most recent testing and operating data that has resulted in the installation of Derrick Multifeed sandwich deck screens in Minntac Steps I and II. Pilot-plant test results that were obtained at the Coleraine, Minnesota Research Laboratory are also reported and demonstrate the effects of feed rate and feed percent solids on sandwich screen performance with two sizes of Minntac fine screen feed.

Jan 1, 1984

By B. Schimm

Improve the mines productivity by simplifying the mining process, for these tasks the Wirtgen Surface Miner offers an attractive alternative. Surface Miners cut, crush and load material in one operation with only one machine. The cutting depth is controlled exactly.

Jan 1, 1997

By R. Kent Comann

Introduction This article describes ways to maximize employment potential for those looking for a job in the minerals industry. Advice on the right way to prepare a resume is followed by tips on where and how to look for a job and ways to make the best of an interview. Information on current salaries is also included. RESUME NAME: Give home and college addresses and telephone numbers, ADDRESS: if still in school. Otherwise, give home address and TELEPHONE: telephone plus business telephone number. JOB OBJECTIVE: What do you want to do? EDUCATION: List degree(s), name of college(s), location(s), and date(s) degree(s) received or to be awarded. Do not list your high school but do include postgraduate education, training, or seminars. WORK EXPERIENCE: List your most recent experience first, and the rest in reverse chronological order. Include dates (month and year) and company names. First show the entire time spent with each employer, then list the various jobs (with dates and duties) you may have had with this employer. MILITARY SERVICE: List dates, branch of service, and duties. If you did not serve, delete this section. COLLEGE ACTIVITIES: Show organizations, sports, and offices held. Only list these if you are a graduating senior, otherwise delete this section. PERSONAL DATA: List age, marital status, height, weight (optional), foreign languages spoken, professional memberships, and health (if good or excellent, otherwise do not mention it in the resume). If you prefer a certain location and would not accept a job anywhere else, list the location desired. Otherwise, do not restrict yourself. Also list special skills, hobbies, or interests that will help sell you to the company. Be brief in this section and use good judgement as to what you say. REFERENCES: Furnished on request. Resume Guidelines There are some things to remember when preparing a resume. These include: • Limit your resume to one page, unless you have a lot of experience. Then it should be a maximum of two pages. • Use 8.5 x 11 plain bond paper, white or off-white. Stay away from colored paper, odd size paper, and cute resumes. They are counter-productive. • Make certain your resume is typed professionally. Be sure to check for spelling, grammar, and typographical errors. • Have your resume reproduced by copier or printing shop. Do not use carbon copies. • Keep your sentences and remarks short and punchy. Use action verbs. • Have a good layout that is easy to read, brief, and uncluttered. Allow some white space in your resume. There are also some things you should not do when preparing a resume. These include the following: • Do not include a photograph or mention your religion, race, or sex. • Do not leave gaps of time unaccounted for in your resume. • Do not include your college transcripts with your resume or list all the courses you took in college. • Do not list all the articles you have written. Only list one or two, if appropriate for, say, a research and development job. • Do not include reference letters with your resume. Any good, prospective employer will make telephone reference checks. • Do not use "Curriculum Vitae," use "Resume." • Do not include unnecessary data such as your social security number, passport number, or PE registration number. If you are a PE or EIT, be sure to mention that in your resume. Do not mention US citizenship or US work permit unless you have a foreign education or are not a native US citizen. • Do not include present salary or salary requirements. This will come out in the interview. • Do not use the word "I" in your resume or refer to yourself in the third person. • Do not lie, distort, exaggerate, or editorialize in your resume. • Do not have your resume prepared by an outside resume service. This is unnecessary, costly, and generally not effective.

Jan 2, 1985

By M. Haase

[ ] How important is a robust communications system for your mine site in order to meet operational and safety requirements? Do you currently have VSAT in place and need a low cost, high quality multi-line VoIP phone system at the site? By adding a single, compact piece of hardware, you can utilize your existing satellite internet connection and have as many as twenty-four separate phones lines from a single unit. The platform is scalable for any size of operation and can be implemented above or below ground.

Jan 1, 2012

By L. J. Jansen

Techniques utilized to incorporate geological data in computer modeling and ore reserve estimation have undergone considerable evolution during the past fifteen years. Computer analysis and evaluation of two precious metal deposits are presented as examples of innovative computer techniques developed at Asarco. The first is a gold deposit occurring in a steeply dipping Pre-Cambrian greenstone sequence. The second is a manto-like manganiferous silver deposit occurring in a relatively flat sequence of Late-Paleozoic sediments. In both deposits, four sub-horizontal zones of geological influence are evaluated.

Jan 1, 1985

By R. H. Church

The Bureau of Mines' Tuscaloosa Research Center has developed a field test unit (FTU) which dewaters mine and/or mineral processing by-product slurries. The feed material (by-product slurry) is mixed with a known quantity and specific type of synthetic polymer (usually a polyacrylamide) to induce flocculation in a continuous operation. The flocculated material passes over a specific number and size of slotted stationary screens which separates the flocculated solid material from the "clean" water. The "static screens" are positioned at a fixed angle to maximize flow capacity and capture of the solids content. An investigation was conducted at an industrial crushed stone operation located near Birmingham, AL, to determine if the Bureau's FTU could successfully dewater the waste slurry generated during grinding and sizing operations at this facility. The investigation showed that waste slurries could be dewatered to 50 pct solids, at a polymer cost of approximately $0.85/ton of dry solids treated, and resulted in approximately 85 to 95 pct solids recovery. The dewatered material continued to consolidate and reached 69 pct solids in 24 h. Presently, the waste slurry generated at this facility is discarded into impoundments. However, this research has identified the recovered waste as an economically marketable product.

Jan 1, 1994

By A. L. Stomberg

Federal and State surface coal mining regulations require special handling of prime soil materials which result in additional costs, and no actual benefit when prime and non-prime soils are similar. The Coteau Properties Company proposes to mix both prime and non-prime topsoil and subsoils at the Freedom Mine in Mercer County, North Dakota, based on an analysis of soil physical and chemical characteristics which show these materials to be comparable.

Jan 1, 1985

By John C. Brower

Bolivia is nor a major gold producer but has produced continuously since pre Inca times. Production reached a peak in 1964 of about 4,000,000 grams and is currently about 1,000,000 grams. Production is mainly from the Tipuani River valley north of La Paz and is derived from Pleistocene basin fill: the Cangalli conglomerate and overlying terraces. Abandoned Pleistocene lake terraces south of La Paz in the Oruro area are another source of gold whose potential have not been realized. In both the Tipuani and Oruro areas, primitive hand methods are the principal means of production, with the exception of a single modern dredge. In spite of a long history of production, probably very little of the gold potential has been mined.

Jan 1, 1979

By D. Nutakor

The ability of computers to create synthetic representations of the real world in virtual reality offers a number of opportunities to enhance training methods used in the mining industry. Unfortunately, the training effectiveness of virtual reality systems currently used in the mining industry has received only limited testing. Miner Simulation (MinerSIM), an augmented reality system with integrated hypermedia suitable for training underground miners in the basics of using a jackleg drill to install rock bolts in a virtual mine environment is in its evaluation process at the University of Missouri-Rolla Experimental Mine. This paper discusses evaluation methodologies of the MinerSIM system, which consists of experimental and control groups with control students learning via traditional lecture and text formats. Preliminary results from usability tests of the first part of MinerSim, which is an online tutorial on underground rock bolting, are presented.

Jan 1, 2008

By C. A. Born

AMAX Inc. climax's mine-mill complex at Climax, Colorado is best known for its molybdenite production: 50,000 TPY of molybdenite flotation concentrate (95% MoS2) from mill heads containing 0.35% molybdenite. Less recognized are the byproducts that are concentrated from the tails generated in the rougher flotation circuit (see Figure 1). Climax recovers a heavy mineral concentrate by passing the rougher tailings from molybdenite flotation over Humphrey spirals (Figure 2a). This concentrate is floated using xanthate at pH 4 to remove sulfides, principally pyrite. The tails from the pyrite float are then cleaned of quartz, feldspar and light minerals by tabling (Figure 2b). Amine flotation follows at pH 1.5 and 75°C to float monazite (Figure 2c). The present circuit at Climax dries the monazite flotation tailings and utilizes high intensity cross-belt magnetic separation Figure 2d) to generate a high grade wolframite concentrate and a low-grade cassiterite product, both of which are contaminated with the mineral brannerite, (UO, TiO, UO2)TiO3. The uranium specifications have recently become difficult to meet due to the increasing percentage of brannerite reporting in the mill feed. A plant is being built utilizing hot sulfuric acid and sodium chlorate to leach this uranium from the monazite flotation tailings prior to their being fed to the wolframite- cassiterite magnetic separators. This modification is the subject of our paper.

Jan 1, 1975

By T. W. Healy, W. J. Trahar

INTRODUCTION The flotation of minerals from their ores in flotation cells involves understanding many chemical and physical processes ranging from electronic events in the bulk mineral and in the mineral surface regime. molecular events at interfaces, the statics and dynamics of thinning and rupture of microscopic to molecular intefacial films, the fluid mechanics of bubble- particle events, the dynamics of air-water-solid colloid states in a flotation machine, etc. etc. D.W. Fuerstenau, whom we honour in this symposium has made unique contributions to many of these diverse physico-chemical and technological sub-processes. The present paper is concerned with a number of observations of the behaviour of minerals in flotation cells and the surface science of some mineral sulfide-water systems. We do not intend to be comprehensive in our analysis, but rather to highlight the challenges that face the scientific masochist who chooses to understand "froth flotationn. In what follows, emphasis is placed quite deliberately on technologically relevant, dynamic or realistic flotation processes i.e. the recovery in a froth of a given sulfide mineral particle of a given size and history from synthetic or actual ores in a flotation cell. The paper also attempts to use the understanding that is emerging from the area of photoelectrochemistry of colloidal

Jan 1, 1989

By Jeffery H. Stricklin

Jim Walter Resources operates five underground coal mines with longwall faces in operation in four of the mines. Due to high air velocities (1000-1200 fpm) needed for methane control together with the friability of the coal, dust control on JWR longwalls offers unique challenges. We have tested many innovative measures to reduce respirable dust concentrations on longwalls with varying degrees of success. These measures include the "shearer clearer" system, different drum water spray configurations, sprays on the longwall belt, stageloader and crusher sprays, wetting agents in the spray water system, and homotropal ventilation. Water infusion of deactivated horizontal methane drainage holes in longwall panels is now being evaluated. A study was completed in November 1986 where water was infused into two horizontal de-gas holes. Personal gravimetric samplers were used to measure respirable dust concentrations and showed a significant reduction in the infused zone. A more in depth study will be conducted. This paper will describe the dust control measures presently used on JWR longwalls, give the results of past studies, and discuss new methods proposed to control longwall dust.

Jan 1, 1987