Search Documents

By I. M. Arbuthnot

Over the last five years, a large number of small to medium sized carbon-in-pulp gold treatment plants have been built in Australia, most designed to treat between 250,000 -1,500,000 tpa of ore. In many cases, the primary requirement was to get a plant built and operating in a short period of time and at minimal capital cost, relating to the limited capital resources and tight cash flow positions of these relatively small mining companies. Since the inclusion of both pre-leach and tailings thickeners resulted in an obvious and significant capital cost, most plants were built without thickeners, without doing a detailed cost-benefit analysis on their inclusion, However, the increasing use of High Rate Thickener?s (HRT s) in the mineral processing industries resulted in a reassessment, in some cases, because of their considerably lower cost. This reassessment was triggered primarily by the need to conserve water in arid mining areas, where borefields were costly to install and water was limited. It has become apparent, though, since startup and operation of these installations, that the savings in cyanide consumption is also a very significant factor and can be used as a primary justification for the installation of a HRT in many cases.

Jan 1, 1991

By Ihsan Berk Tulu, Ted Klemetti, Deniz Tuncay, Cicek Sena, Zhao Haochen

"Analysis of Longwall Pillar Stability (ALPS) and Analysis of Retreat Mine Pillar Stability (ARMPS) treat the pillar as a passive structure that is designed to carry overburden dead-weight. This dead-weight is calculated by simple rules based on the geometry of the mining, such as “tributary area theory,” “pressure arch theory,” and “abutment angle theory.” Although the pressure arch loading approach indirectly accounts for the generally stiffer overburden response of narrow and deep panels, it does not include the effect of specific geology of the overburden in load calculations. The relationship between successful pillar layouts and overburden geology can be incorporated into the load calculation by using the Ground Response Curve (GRC) approach.This paper introduces the GRC modeling methodology to investigate the effect of overburden geology and excavation geometry on load transfer mechanisms using seven field measurement case studies from four U.S. mines. It was also shown that the modeling methodology used to derive GRC in this study approximates mining-induced stresses and deformations within 5% of the values measured in the field.INTRODUCTIONFrith and Reed (2017) stated that current state-of-the-art pillar design methods ignore the overburden mechanics and use estimated dead-weight of overburden to compute pillar sizes. In the United States and around the world, overburden loading is typically estimated by simple geometric rules, generally with the tributary area theory (TAT). The specific overburden mechanics, structural competence of the overburden strata, geology, in situ stresses, and overburden/pillar interactions are typically ignored. However, these important mechanical responses affect the stability of the mine pillars and openings; therefore, they also affect the safety of the mine workers.Research conducted by the National Institute for Occupational Safety and Health (NIOSH) after the Crandall Canyon mine disaster (Esterhuizen, Mark, and Murphy, 2010) showed that small panel width-to-depth ratios and stiff-strong overburden result in a reduction of the observed pillar loads, much smaller than the TAT estimate. In fact, as a response to the Crandall Canyon disaster, Mark (2010) implemented a pressure arch loading approach into the latest ARMPS program to recognize the inherently greater stability of narrow panels at depth. The pressure arch approach is a first logical step to introducing non-tributary area loading into the practical ARMPS program. Although the pressure arch loading indirectly accounts for the generally stiffer overburden response of narrow and deep panels, it does not include the effect of specific geology and mechanical response of overburden in the load calculations."

Jan 1, 2019

By M. M. Rajkovich

Just prior to the close of the century, the Federal Mine Safety and Health Review Commission issued its long-awaited decision in Berwind Natural Resources, et al v. Secretary of Labor, to usher in the new millennium. The case arose as a result of a mine explosion in Eastern Kentucky resulting in MSHA’s issuance of 225 citations, not only to the contractor, but to four affiliated entities of Berwind Corporation. While an Administrative Law Judge dismissed those citations as to three of the Berwind entities, both MSHA and the remaining Berwind entity appealed the case to the Commission. Although the Commission effectively left intact the Administrative Law Judge’s decision, it announced a new theory of liability that would apparently be applied in the future, namely the Unitary Operator Theory. This presentation will provide an in-depth look into the Berwind decision and explore the means under which MSHA might impose liability for contractor violations upon other entities in the future.

Jan 1, 2001

By H. Saito

To Japan, which is scarce in natural resources, limestone is the only mineral resource comparatively rich in ore reserves and having broadly recognized outstanding quality. Distribution of the limestone deposits extends from Hokkaido in the north to Kyushu and Okinawa in the south, and the deposits are located in a manner of framework formation of the Islands of Japan. Studies of the geological ages of these ore deposits reveals that almost all of the main ore deposits west of Kanto Area belong to the Carboniferous Period - Permian Period of the Paleozoic Era. Also in the east of Kanto Area, deposits belonging to the Paleozoic Era constitute the main part, although recently there are increasing examples of reclassifying the geological age of the deposits heretofore considered as Paleozoic Era to the Triassic Period of the Mesozoic Era by the recent discoveries of the fossils of conodont, etc. Large ore deposits and main ore deposit groups are given in the Figure 1, which shows that the deposits are roughly found well distributed throughout the country.

Jan 1, 1982

By Kevin Stuffle, James E. Sharp, Sean Premeau

Two process enhancements for the biological oxidative pretreatment of sulfidic gold ore for subsequent treatment with cyanide are discussed. These are the use of a high areal density ring and pin packing (BioBalls™) as substrate, and the use of a novel biological ferric generator. The BioBall™ packing when coated with concentrates for heap leach processing offers higher areal densities, while leaving more open volume for fluid flow than more commonly used substrates such as aggregate. An oxidation rate study was performed on crushed auriferous arsenopyrite whole ore to demonstrate the benefits of using the packing. The auriferous arsenopyrite grading 2.9% Fe and .212 OPT gold was 50 percent oxidized in 24 days. The biological ferric generator is a passive air-side trickle bed reactor that efficiently converts ferrous to ferric in a process stream. Conversion rates of .8g/L h ferrous to ferric are routinely obtained. Although the biologically generated ferric solutions have not yet been tested on gold ores or concentrates, prior work has demonstrated that the high ferric solutions which will result in rapid oxidation of sulfidic gold ores or concentrates.

Jan 1, 1997

By B. Jensen, R. Davis, P. Golledge, A. D. S. Gillies, W. Urbanik Urbanik

A current program of research on the explosibility of coal dust/methane mixtures is described. During the study an explosion test chamber based on a novel design has been developed. This 20 litre open chamber uses a rotating drum concept for dust dispersion and infra-red sensors for dust concentration measurement. The chamber design allows different initiators to be tested while varying methane gas and coal dust concentrations. A new approach to the determination of coal dust concentration is included with a description of a dielectric dust probe. The measurement technique is based on the change in dielectric constant as the proportion of coal dust in air between probe capacitor plates increases or decreases. Characterization of coal dust samples is of vital importance. The particle size distribution, coal proximate analysis and elemental analysis were studied. Coal dust was sourced from airborne collected samples, settled dust from mine sources and seam channel samples crushed and sized. Explosibility test results indicate that a very low concentration of coal dust can form an explosible mixture when dispersed in methane concentration of just below five percent. With low temperature initiators, the coal dust lean limit concentration rises rapidly as the methane concentration is reduced. An accurate knowledge of the potential explosion hazards of coal dust and coal dust/methane mixture is necessary to establish safe operating conditions in underground mines. The research results outlined extend knowledge in this area.

Jan 1, 1989

By III Kimball

For many years, Arizona merely shadowed EPA's environ-mental regulation of mining operations and waste. During this period, Arizona generally assisted EPA in the implementation of federal programs and enacted environmental laws patterned closely after their federal counterparts. A growing public concern about protecting water quality, particularly groundwater quality, eventually caused the State to depart from this pattern.

Jan 1, 1989

By Matias Pentinnen, Wayne Dickinson

Electrowinning is a key process for copper production contributing roughly twenty percent globally and thirty to forty percent of production in the Americas1. Copper grade is assessed largely on deposit smoothness and on level of impurities in the metal. Smoothing aids are essential to create dense, low porosity deposits and guar has long been the material of choice for this purpose. Guar is, however, poorly stable under the strongly acidic electrowinning conditions, underlying ongoing research to identify an effective, acid-tolerant replacement. Current efficiency is also a critical factor in controlling copper production costs and chemical additives should ideally improve current efficiency as well as improving deposit smoothness.

Feb 1, 2025

By John B. Rigg

The title of my paper today is "public relations challenges for the pending minerals crunch". There isn't anyone in this room who would dispute. That the minerals industry has always had public relations challenges . . . No matter what the circumstances, mineral shortage or abundance. The industry suffers from an image that is second to none in longevity. It defies all actuarial formulas of the past or the future. Never mind that such an image is outdated, distorted, overstated, and reiterated. I submit that the minerals industry had public relations challenges long before there was anything called public relations. This account of egyptian mining practices, recorded for posterity by Diodorus Suculus at the end of the second century, b.c., is indicative. "On the confines of Egypt . . . And Ethiopia is a place which has many great mines of gold, where the gold is got together with much suffering and expense. The kings of Egypt collect together and consign to the gold-mines those who have been combined for crime, and who have been made captive in way . . . Sometimes only themselves, but sometimes likewise their kindred. "Those who have been consigned to the mines, being maw in number and bound with fetters, toil their tasks continuously both by day and all night long, getting no rest and jealously kept from all escape.

Jan 1, 1975

By Corale L. Brierley

The effect of hydrogen peroxide (H2O2) on growth and respiration of Thiobacillus, thiooxidans, and Thiobacillus ferrooxidans, organisms involved in acid leaching of copper sulfide minerals and uranium oxides, was examined. Oxygen uptake and growth by T. thiooxidans were inhibited after contact with 0.82 mM H2O2. Inhibition of oxygen uptake by T. ferrooxidans occurred at 8.24 mM H2O2, and growth was inhibited after 6 hours exposure to 2.06 mM H2O2. Higher concentrations of H2O2 can be used without detriment to thiobacilli if it is dissipated prior to reaching the oxidation pond or dump surface. INTRODUCTION In recent years, hydrometallurgical processes for recovery of metal values from low-grade ore minerals have played an increasingly important role. Dump leaching of low-grade copper waste materials in the western United States now yields 11.5% of the total U. S. copper production. Although scavenger operations in uranium leaching have been successful, the state-of-the-art of in-situ

Jan 1, 1977

By J. C. Stankus

Many coal seams are associated with soft floor strata and during mine development if coal pillars are not properly designed, floor heave occurs and causes interruption of coal production. In the severe cases, the section or mine is abandoned. One of the methods for controlling floor heave is floor bolting. This paper describes the demonstration of floor bolting methods in a West Virginia coal mine. Three methods were used: (1) vertical full resin bolting, (2) floor truss bolting, and (3) floor truss bolting plus a floor cut at the center of the entry. The design of each method and the experimental results are discussed in detail.

Jan 1, 1993

By Issac Douglas, Sheila Devasahayam, John S. Thella, Manoj K. Mohanty, Jeremy Prishmont

The flotation performance of Sodium O, O-diisobutyl Di thiophosphate (referred to as reagent A) was compared with Aerophine 3418A (referred to as reagent B) for floating a complex copper ore grab sample (Ore A). Preliminary test results indicated a cumulative copper concentrate grade of 10.19% with a recovery of 86.31%, which was achieved with reagent A from a feed consisting of 5.32% Cu. The grade and recovery achieved using reagent B are 9.11% and 87.85%, respectively. A comparative analysis based on the preliminary test results indicated that reagent A’s performance is better than that of reagent B at lower concentrate grades, specifically below 12% Cu. However, the flotation performance is better for reagent B at higher concentrate grades (>12% Cu). A more detailed study was conducted to optimize the grade-recovery performances achievable from both reagents on a complex low-grade copper ore sample (Ore B) from Western USA. Test results indicated a copper concentrate with a grade of 5.5% Cu and 78.59% recovery was obtained with reagent A compared to 4.31% Cu and 62.04% recovery with reagent B from a feed consisting of around 0.25% Cu.

Feb 22, 2026

By V. Arad, S. Arad

Besides the conservation and closing activities, an important issue to achieve is the environmental rehabilitation of the mining perimeters, also assuring the continuity and sustainable development of the mining activity in the Jiu Valley. Modifying and depleting the soils by mining works and dumps of mineral waste as a result of coal mining and tailing is one of the important aspects. The paper’s aim is to analyze which are minerals and resources policies of our government and to adopt measures for sustainable development in the coal mining in this region. The measures to reduce the instability risk for the mining works and waste dumps, which could affect the underground mining constructions or the related surface areas, were consider. It is most important to establish the priorities in order to obtain a high efficiency by combining the measures according to the environmental analysis and risk assessment.

Jan 1, 2005

By William G. Davenport, Eric H. Partelpoeg

Direct smelting of copper in a single vessel has long been the extractive metallurgist's dream. Such a process offers the important advantages of (i) maximum use of the energy available from oxidizing the sulphur and iron of the concentrate; (ii) restriction of SO2 emissions to a single constant-strength source; (iii) minimum materials handling and (iv) elimination of at least one process step. Extensive developmental work was carried out in the 1960's and 1970's to implement such single-step processes. Some of the processes reached the prototype stage and it appeared that copper smelting technology was on the threshold of a new, efficient, minimum-pollution era. Since that time, however, the forward thrust has slowed and single-step smelting is still a process of the future. The paper describes in detail the potential advantages of single-step smelting; its history and current status; and the reasons why it has not been adopted industrially. It concludes that the potential benefits of single-step smelting are powerful and that many of the difficulties encountered in the 1970's will be overcome in the 1980's.

Jan 1, 1985

By Diane Jones, Jeremy Spearman, Tom Matthewson

Requirements for minerals are on the increase globally and the deep sea offers a potential source of essential materials. Extracting these minerals from what is considered an environmentally sensitive area, and one about which little is still known, is a challenging activity, which needs careful consideration and an appropriate environmental impact assessment to be carried out. Extraction of material from the deep sea beds can cause disturbance or damage to benthic communities; impact on mobile marine species such as fish, mammals and reptiles; cause increases in suspended sediment and sediment deposition onto potentially sensitive areas or potentially release contaminants which were previously bound to the sediment. This paper discusses the potential environmental issues surrounding extraction of deep-sea deposits using aggregate dredging techniques and how those issues can be appropriately assessed. In particular issues of suspended sediments, plume transport, water and sediment quality and underwater noise impacts on potentially sensitive species and habitats will be explored.

Sep 1, 2014

By J. L. Watson

n the U.S., lead has been produced via blast furnace processing for over a century, and the slags from that pyro-metallurgical process have been accumulating on industrial sites over that extended period. Lead blast furnace slags typically contain both lead and zinc compounds in an iron-silicate matrix, and it appears highly likely that such materials will have to be processed in the near future to meet with EPA regulations. Thus it is appropriate to investigate possible processing routes to render the slags non-hazardous and simultaneously to recover metal values to partially off-set the inherent high cost of processing such materials. There are two major processing alternatives: one being pyrometallurgical and the other hydrometallurgical. The research reported here investigates leaching/solution purification/recovery processes for lead and presents experimental data for the treatment of lead blast furnace slags from S.E. Missouri. The results of the research suggest that both lead and zinc can be removed effectively from the slag, and that metallic lead can be recovered directly from the organic extractant utilized for solution purification.

Jan 1, 1995

By R. Owen

The vision-based approach to process control involving fine particles in harsh on-line environments is discussed in this paper. The sensor equipment at the process location, consisting of a light source and a CCD camera provides RS-170 B&W video output. The video can be seen on a process monitor in the control room and is sent to a computer based Vision Processor. The Vision Processor contains a video digitizer and Canty developed software that extracts process information. The iron mine application controls thickener agent feed rate and thus settling pond overflow clarity. The sensor is mounted in the overflow flume of the outdoor settling pond and is used year around in the Minnesota weather. Alternate control system needs a low flow water sample which is subject to freezing in winter. The computer based vision processor provides 4-20 mA analog outputs for real time control as well as file archive for a history record.

Jan 1, 2001

By T. M. Yegulalp

A short review of the current practice and recent developments is followed by a description of a newly developed approach for the solution of the optimum ultimate pit limit problem. The new approach utilizes the network modeling of the problem for solution by maximum flow algorithm. The latest developments in the implementation of maximum flow algorithm present significant time and memory savings as compared to initial development due to Ford and Fulkerson. Results of a series of computational tests are presented to demonstrate how this approach performs as compared to the well-known Lerchs Grossman algorithm. It is also shown that the solution by the new method will automatically include several optimal solutions based on predetermined number of benches to be included in the analysis.

Jan 1, 1993

By S. S. Peng

Hydraulic powered supports have been employed in the U. S. longwall mining for the last two' decades. Yet the sciences of roof control at the powered supported faces remain largely unknown. Many questions remain unanswered. To address the problems, field investigations were conducted from 1980 to 1984 in seven longwall faces (1-10)(Table 1). Some of the findings have been reported by Peng and Chiang (11). The basic geological conditions of these panels are listed in Table 2. The mining equipment used in these longwall panels are listed in Table 3. Instrumentation and Observation Programs Two events were generally instrumented: one was the hydraulic leg pressures of the powered supports, and the other was the canopy and base plate load distributions.

Jan 1, 1986

By M. Ahmadiantehrani

The concept of hypochlorite treatment prior to cyanidation in the heap leaching of low grade carbonaceous gold ores is discussed. Laboratory column leach tests using a low grade carbonaceous ore were performed to investigate the effects of pH, concentration, hypochlorite consumption, and bed height on the total gold extraction. At high pH, the hypochlorite stability increases and thus, hypochlorite consumption is decreased. At room temperature, the total gold extraction is proportional to the hypochlorite consumption. However, at some point additional hypochlorite consumption does not increase gold extraction. Gold recoveries of 10 and 80 percent are obtained for 12 and 167 lbs/ton hypochlorite consumption, respectively. Increasing hypochlorite concentration increases the rate of extraction. For a given hypochlorite consumption gold extraction was increased by shortening the ore column height. Finally, calcium hypochlorite is more effective than sodium hypochlorite.

Jan 1, 1990