Search Documents

By Richard Minnitt, Philippe Renard, Christina Dohm, Winfred Assibey-Bonsu, Matthew Aboagye, Julien Straubhaar, Mahlomola I. Mabala

The application of multiple point statistics (MPS) in oil studies has gained traction over the years; however, the use of MPS in mineral resource estimation and classification is still limited. This is despite MPS’ ability to deal with complex and heterogeneous geology better than the commonly applied two-point based methods. The availability and choice of a representative training image (TI) are often cited as the main challenge holding back MPS’ application in mining geostatistical studies. On the other hand, the general approach used in mining whereby early focus is on higher grade areas and lower grades are planned to be mined later presents a massive opportunity for the development of representative TIs. Mined-out areas provide large amounts of historical data that can be used to develop training images or training datasets that can be used to estimate in mining extension areas (often lower in grade), provided low grade areas are underpinned by similar geology analogue. This approach will enable more robust estimates in mine/pit extension areas for both high- and low-grade extensions than with traditional two-point geostatistical methods.

Jun 25, 2023

By M. J. Friedel

The U.S. Bureau of Mines (USBM) investigated the use of seismic refraction tomography (SRT) for identifying changes in pillar loading at the Foidel Creek coal mine near Steamboat Springs, CO. The inherent three-dimensional problem of directly imaging coal pillar conditions is reduced to a single plane by considering only the load transmitted from the pillar to the adjacent floor rock. Floor strata velocity tomograms (at two pillar locations) illustrate that loading conditions are non-uniform and non-unique. Also, time sequence monitoring, as the longwall face advanced, demonstrated that SRT can be used to image spatial changes in loading conditions. SRT offers the mining engineer a simple and flexible technique for evaluating pillar conditions, and thus, both present and alternative mine designs.

Jan 1, 1994

If one can embrace the medical analogue, much of the mining industry currently suffers from a massive bacterial infection. When pyrite-bearing or sulfide-bearing rock formations, tailings, or mine wastes are infected by Acidithiobacillus ferro-oxidans, the likelihood of forming acid rock drainage (ARD) is almost guaranteed. The ?pharmacy? of antibiotics available is extensive, ranging from solid alkaline amendments like limestone to liquid ?medicines? such as sodium lauryl sulfate, sodium thiocyanate, waste milk, and bipolar lipids. Unfortunately, the ?geo-medical? teams of geochemists, microbiologists, engineers, and mine managers lack the tools to surgically apply these active ingredients where they are needed most with a minimum of waste. Distribution of fine grained limestone on the surface of an acidic mine waste dump is analogous to applying a bandage soaked in antacid to treat an upset stomach. The implementation of up-to-date best management practices has not healed the patient; an equivalent combination of hypodermic needle, cyber knife, and arthroscopic probe is clearly needed. Using an engineered, flow-able or pumpable foam or pHoam? as the medicinally analogous ?dextrose delivery solution? for solid and/or liquid ?geo-antibiotics?, the authors have combined off-the-shelf technologies that have been previously applied in solving geotechnical problems in the mining industry. A patent for the innovative process is pending. This paper discusses method concepts and the advantages it could provide over conventional BMPs.

Jan 1, 2012

By Mohammed Laraba, Rodrigo Alvarez Garcia, Juan Maria Menendez-Aguado, Roula Abdelmalek

The aim of this research is the study of the WHIMS parameters on the improving process of a local (DD: Djebel Debbagh, East of Algeria) kaolin. The obtained results of performed XRF, SEM, and XRD characterization showed that this local material is an alumino-silicate containing kaolinite and halloysite with MnO and Fe2O3 impurities (respectively 39.30% and 34.67% alumina and 38.18% and 39.70% silica in both samples (DD2 and DD3). After homogenization, crushing, and milling, a multiparameters factorial experimentation (grain sizes, intensity, and dimension of matrix balls) showed that WHIMS is an effective process to improve the quality of this kaolin, mainly: removing their impurities. Dimensions of matrix balls (Db) = 2 cm, intensity of the applied magnetic field (I) = 1.5 T, and grain sizes (Dp) = > 100 < 250 μm) are the optimal values to reach 91.06% for manganese and 93.45% for iron as removing yield. The statistical analysis of these results sorted the investigation parameters and showed that Db has the highest and most significant influence on the recovery of iron and manganese particles. The magnetic field intensity (I) has a less important influence while the grain size has an average influence (positive on the iron recovery but a negative one on the recovery of manganese).

Jun 11, 2022

By A. B. Cecala

Video technology coupled with datalogging exposure monitors have been used to evaluate worker exposure to different types of contaminants. However, previous application of this technology used a stationary video camera to record the worker?s activity while the worker wore some type of contaminant monitor. these techniques are not applicable to mobile workers in the mining industry because of their need to move around the operation while performing their duties. the Helmet-Cam is a recently developed exposure assessment tool that integrates a person-wearable video recorder with a datalogging dust monitor. these are worn by the miner in a backpack, safety belt or safety vest to identify areas or job tasks of elevated exposure. After a miner performs his or her job while wearing the unit, the video and dust exposure data filesare downloaded to a computer and then merged together through a NIOSH-developed computer software program called enhanced Video Analysis of Dust exposure (eVADe). by providing synchronized playback of the merged video footage and dust exposure data, the eVADe software allows for the assessment and identificationof key work areas and processes, as well as work tasks that significantlyimpact a worker?s personal respirable dust exposure. the Helmet-Cam technology has been tested at a number of metal/nonmetal mining operations and has proven to be a valuable assessment tool. mining companies wishing to use this technique can purchase a commercially available video camera and an instantaneous dust monitor to obtain the necessary data, and the NIOSH-developed eVADe software will be available for download at no cost on the NIOSH website.

Sep 1, 2013

By Jorge Armstrong, Sean Warren, JOSEF BOURGEOIS

The application of statistical analysis software programs has proven useful for the investigation of rockfall runout distance along a designed slope. Rockfall modeling programs are continually being upgraded with more sophisticated analysis tools, such as the use of the rigid body versus lump mass models. Engineers at mine sites utilizing the software may have varied experience related to these models, their associated input parameters, and how to interpret the generated results. To address this concern, researchers at the Spokane Mining Research Division (SMRD) of the US National Institute for Occupational Safety and Health (NIOSH) investigated the influence of slope height, slope angle, slope material, and rock size for both rigid body and lump mass models in a 2-D statistical analysis program. Based on a literature search and industry input, specific ranges common to that of an open pit mining environment were chosen for each of the input parameters to determine 90% rock runout distance as well as their sensitivity to change. Data collected from this numerical analysis and simulation will be compared to empirical rockfall data gathered through the duration of the Highwall Safety project conducted by NIOSH from 2022–2026.

Jun 18, 2023

By Robert J. Ramsey, N. Finkelstein, Foster J. Witthauer

First mining operations in the Tyrone District, located just north of the Burro Mountains in Grant County, New Mexico, commenced in the 1870&apos;s. A major operation was undertaken by Phelps Dodge Corporation in the early 1900&apos;s when a 2,000 ton per day underground mine was developed and a gravity concentrator was built east of the mine and across the Continental Divide. It was during this time that the picturesque Tyrone townsite was built and occupied. In 1921, however, the underground operation was closed because of high operating costs and low demand for copper. The area was drilled extensively during the 1950&apos;s and in October 1966 Phelps Dodge announced the pending development of the new Tyrone with a large open-pit mine, a modern concentrator, suitable support facilities, and a new townsite to be located between the mine and Silver City. Stripping for the pit and construction of shop and milling facilities began in 1967. By the spring of 1969, ore was being stockpiled near the primary crusher. Operation of the concentrator on a 3-shift per day basis commenced on July 17, 1969. The concentrator as initially built had one primary, two secondary, and five tertiary cone crushers, two grinding sections of six ball mills each, two flotation sections, four filters, and four tailing thickeners. &apos;he capacity was about 30,000 tons per day. In 1971 and 1972, the capacity was increased to 48,000 tons per day by the addition of one secondary and two tertiary crushers, one section of eight ball mills, one flotation section, two filters, and four more tailing thickeners. Centralized automatic control was built into the original and expanded facilities to the greatest extent possible, considering the state of the art at that time. Installation of additional control

Jan 1, 1976

By A. House

Newmont Mining Corporation owns and operates the Phoenix Mine near Battle Mountain, Nevada, USA. The existing milling facility has operated since 2006. Following the startup of the milling operation, and coupled with the upswing in the copper market, Newmont realized that Phoenix needed a process option to treat lowgrade transition and oxide copper ores. This meant that potentially revenue generating ore was being mined as waste. With no system in place to treat the transition and oxide copper, work began to determine the most feasible approach. After evaluating multiple options, the flow sheet was set for a run-of-mine (ROM) heap leach pad and solvent extraction/electrowinning plant (L-SX/EW). This paper will discuss the synergies and challenges of developing a copper L-SX/EW plant at the Phoenix copper-gold mill.

Jan 1, 2010

By Frederick B. Henderson

On 10 August 1976, The Geosat Committee was organized in Denver to institute The Geosat Program. This program is an industry backed effort to evaluate and help select optimum space remote sensing systems for geological purposes. It is believed that the recommendations of The Geosat Committee can be supported by industry as additional exploration tools which can materially benefit industry and the Nation with respect to our energy and other natural resources needs. Appended is a general summary of The Geosat Committee Organizational Meeting and general review of The Geosat Program. The Geosat Workshop Report. The Geosat Committee, and The Geosat Program will be reviewed at a special afternoon session, Friday, 3 September.

Jan 1, 1976

By B. Basim

Novel chemicals that can be used for increasing the efficiency of fine coal dewatering were developed at Virginia Tech. Reagent A was tested on three different coal samples in laboratory vacuum filtration tests. These included flotation products from Middle Fork plant, Elkview Mining Company, and CONSOL, Inc. The tests conducted with the Middle Fork coal sample (100 mesh x 0) showed that cake moisture can be reduced by more than 10% beyond what can be achieved without using dewatering aid. This improvement was achieved at 1 lb/ton of Reagent A and 0.1 inch cake thickness. At 0.5 inches of cake thickness, the improvement was limited to 8% at the same reagent dosage. The results obtained with the Elkview coal (28 mesh x 0) showed similar advantages in using the novel dewatering aid. Depending on the reagent dosage, cake thickness, drying cycle time and temperature, it was possible to reduce the cake moisture to 12 to 14% range. In addition to achieving lower cake moisture, the use of Reagent A substantially decreased the cake formation time, indicating that the reagent improves the kinetics of dewatering. The test results obtained with CON SOL coal were not as good as with the other coals tested in the present work, which may be attributed to possible oxidation and/or contamination.

Jan 1, 1998

By R. Buisman, K. Reyneke, M. Fullam, J. V. Brown

Most mineral processes currently in use, such as flotation, spirals, gravity concentrators, etc., are only effective over a small range of sizes, hence the upstream need for technology to accurately classify fines by size. The Pansep’s design is revolutionary. Slurry is fed onto connected mesh sections that move without bending or vibration, in a circular motion. Both sides of the screen mesh are utilized, so Panseps are self-cleaning and has half the footprint of other mesh-type screens. Developed in South Africa in 1997, the Pansep has proved itself very effective as a wet fines screen to effectively classify fine mineral fractions from 50 to 2,000 micron (325 to 10 mesh).

Jan 1, 2001

By K. R. Long

Until it was defunded in 1995, the U.S. Bureau of Mines maintained a Cost Estimating System (CES) for prefeasibility-type economic evaluations of mineral deposits and estimating costs at producing and non-producing mines. This system had a significant role in mineral resource assessments to estimate costs of developing and operating known mineral deposits and predicted undiscovered deposits. For legal reasons, the U.S. Geological Survey cannot update and maintain CES. Instead, statistical tools are under development to estimate mining costs from basic properties of mineral deposits such as tonnage, grade, mineralogy, depth, strip ratio, distance from infrastructure, rock strength, and work index. The first step was to re-estimate ?Taylor?s Rule? which relates operating rate to available ore tonnage. The second step was to estimate statistical models of capital and operating costs for open pit porphyry copper mines with flotation concentrators. For a sample of 27 proposed porphyry copper projects, capital costs can be estimated from three variables: mineral processing rate, strip ratio, and distance from nearest railroad before mine construction began. Of all the variables tested, operating costs were found to be significantly correlated only with strip ratio.

Jan 1, 2011

By Michael Schultz, Gregory Sanders

The City of New Haven is planning to construct the Downtown Storm Sewer Infrastructure Improvement project to mitigate on-going stormwater flooding in the Long Wharf District. The proposed project includes a 685 cubic feet per second (cfs) stormwater pump station and a 3,200 linear feet (975 meter) long tunnel segment with an internal diameter of 120-inches (3.05 meters). This paper presents the aspects of the final design and the use of the cloud-based data management software to make better data-informed decisions. The software was used to create a spatially aware database of the subsurface conditions, as well as improve visualization and analysis of the soil properties.

Dec 1, 2022

By Henry Rumfelt

Strip mining in the domestic coal industry is contributing a greater proportion of overall production than at any time in the past. U. S. Bureau of Mimes statistics show that the percentage of total production mined in 1958 by stripping methods in- creased to more than 30 pct, up from 22 pct in 1951. The tendency to favor strip and open pit mining exists in other mining activities, but such trends are not as clearly outlined as in the coal industry. Significantly, the depth of overburden in coal properties considered suitable for stripping is also increasing. A depth of 50 to 60 ft of overburden was once considered to be about the maximum amount that could be handled economically, Today, a depth of 80 to 100 ft is frequently taken into consideration for simple overcasting operations (i.e., excavating over- burden and dumping it in the spoil position where it remains indefinitely). Significantly, the depth of overburden in coal properties considered suitable for stripping is also increasing. A depth of 50 to 60 ft of overburden was once considered to be about the maximum amount that could be handled economically, Today, a depth of 80 to 100 ft is frequently taken into consideration for simple overcasting operations (i.e., excavating overburden and dumping it in the spoil position where it remains indefinitely).

Jan 1, 1960

By O. J. R. Baena, N. J. Zapata

In Colombia, more than 15 regions and around 100 municipalities develop gold mining at different scales, and these operations generate mining waste composed of processing fluids and crushed rock with metals and high silica content. Cement production requires clinker, gypsum and other corrective additives. Clinker results from the partial fusion of some minerals including silica. In this study is proposed to evaluate the effect of the use of mining tailings sands from gold mining in the manufacture of clinker. The proposed methodology will allow the characterization of the sands to manufacture a cement specimen and measure its physical and fire properties

Mar 2, 2022

By C. T. Wallace

Evans Industries, Inc., a management coal consultant and company was assigned to evaluate National Steel Company&apos;s coal properties in Knott and Floyd Counties, Kentucky. The results of evaluation showed large reserves of good quality, high volatile metallurgical coal contained in the Elkhorn coal beds and resulted in the formation of Beaver Creek Consolidated Coal Company. Based on results of the exploration and feasibility work, the decision was to install a coal nine, preparation plant and related facilities having a production capacity of one&apos; and three quarter million tons per year with Evans Industries acting as Beaver Creek&apos;s management company. The recoverable tonnage assigned to the Stinson Mine is approximately forty-five million tons. This paper discusses the general arrangement of storage, conveying, loading, refuse disposal facilities and the flow sheet of the preparation plant developed by engineers of Heyl & Patterson, Inc., and Evans Industries, Inc., with emphasis on practical flexibility, sulfur reduction in all circuits, and high product yield with the minimum amount of selective mining, Three and one-half miles of railroad have been built by the Chesepeake & Ohio Railroad to service this mine.

Jan 1, 1970

By D. J. Bryden, J. W. Oberholzer

In response to the need for enhanced precautionary measures to safeguard mine workers in collieries from the consequences of methane ignitions in a heading, the coal mining industry has ex- pressed the desire for the development and testing of active on board suppression systems. As overseas systems cannot be used directly in the bord and pillar geometry it is necessary to adapt overseas and local technology to suit local mining conditions, as well as to test such developed systems for their compliance with the expressed needs. As the systems have to be tested in a specific roadway configuration, a facility was developed to enable the testing in South Africa. A surface test facility has been established which can be used to develop and test suppression systems on continuous miners and roadheaders. This facility consists of a tunnel wherein compliance tests can be conducted in simulated underground conditions. A number of methane explosion tests have been conducted in the test facility. The explosions conducted varied in CH,/air concentration (7,5 to 9 percent) and volume (26 to 88 m3). At lower concentrations there was a marked reduction in explosion strength and flame speed. Tests carried out with the Explostop system successfully suppressed the propagation of methane ignitions in both scenarios tested.

Jan 1, 1997

By C. R. Fahnestock

One of the major problems for us in the earthmoving industry is the analysis of materials under the ground surface. Countless engineering and construction jobs would be simplified if there were an inexpensive and fast way to obtain information on problems such as: Depth and solidith of bedrock? Nature of the materials between bedrock and the surface? Adequate foundation for bridges and drainage structures? Location of supplies of materials to be used in construction? Investigation of tunnel sites? Characteristics of swampy areas and investigation of existing and potential slide areas? These questions are of paramount interest to highway contractors as they bid jobs and plan, equipment spreads to handle them at optimum efficiency. Such information also is invaluable to engineers in the design and construction of bridges, buildings, railroads, canals, and tunnels.

Jan 1, 1961

By Enrique Jelvez, Nelson Morales Varela, Christian Ihle, Joaquin Silva

All mineral beneficiation processes require water for its execution. Therefore, the availability and adequate management of water are key to the existence of any mine operation. However, many mines’ operations are affected by water scarcity and risk an increase of operational costs or even production in some cases. This paper proposes a model to minimize the losses of water due to evaporation and re-absorption by adjusting the active and inactive periods of the discharge in different points of the tailing. When applied, the model determines optimal or nearly optimal discharge operation in all the scenarios that were evaluated.

Jun 25, 2023

By C. L. Karr

The efficient management of the distribution of goods and services is important throughout the minerals industry. From the scheduling of processing plant operations, to the routing of work crews in mines, to the planning of product development, vast amounts of time, energy, and money are wasted due to poor planning and scheduling. Thus, the U.S. Bureau of Mines is investigating computational algorithms that can be used to minimize the economic losses related to scheduling and allocating resources. Although there is commercial software available for tackling many scheduling problems, there has been little relief provided for solving the difficult traveling salesman with time windows problem (TSTW). The TSTW problem is a "derivative" of the classic traveling salesman problem, and can be used to minimize the distance traveled by vehicles or personnel to visit all points on a tour, with the additional constraint that each point on the tour must be visited within a specified time window. This paper is a survey of published work in which genetic algorithms have been used to efficiently solve the traveling salesman problem and its more difficult derivative, the TSTW problem. A genetic algorithm is a search algorithm based on the mechanics of natural genetics, and has been used to solve a broad spectrum of engineering optimization problems. Results indicate that the versatility, searching power, and simplicity of genetic algorithms can be used to provide substantial improvement in the area of scheduling and resource allocation.

Jan 1, 1994