Search Documents

By David L. Hill

Newmont Gold Company's Mill No. 4 is located along the Carlin trend, about 25 miles North of Carlin, Nevada. The plant consists of a primary grinding circuit using a 7.2 m (22 ft) diameter by 2.6 m (8 ft) long semi-autogenous mill along with a 2.3 m (7 ft) diameter cone crusher. Secondary grinding is performed in a 4.8 m (14.5 ft) diameter by 9.2 m (28 ft) long overflow ball mill in closed circuit with a set of 66 cm (26 in) diameter cyclones. The ground product is fed to a typical carbon-in-leach gold leach circuit. The grinding/crushing circuit operation and control scheme are the topics of this paper.

Jan 1, 1993

By R. G. Darmody

Longwall coal mining in southern Illinois occurs beneath some of the best agricultural land in the U.S. This region is characterized by highly productive, nearly level, and somewhat poorly drained soils. Subsidence from longwall mining causes changes in surface topography which alters surface and subsurface hydrology. These changes can adversely affect agricultural land by creating wet or ponded areas that can be deleterious to crop production. While most subsided areas show little impact from subsidence, some areas experience total crop failure. Coal companies are required by law to mitigate subsidence damage to cropland. The objective of this study was to test the effectiveness of mitigation in restoring grain yields to their pre-mined levels. The research was conducted on sites selected to represent conventional mitigation techniques on the predominate soils in the area. Corn (Zea mays L.) and soybean [Glycine max.(L.) Merr] yields in 1988, 1989, 1990, and 1991 from mitigated areas were compared to yields from nearby undisturbed areas. There was no significant (a=0.05) difference in soybean yields averaged over the four years. Average corn yields, however, were significantly lower than reference areas. The impact of subsidence and mitigation is variable and site specific. Results were also related to weather. In wet years, yields in mitigated areas tended to be depressed. This research demonstrated that mitigation of subsidence damage can be successful.

Jan 1, 1986

By R. L. Loofbourow

R. L. LOOFBOUROW 26.1-WATER FLOW, USE, EFFECTS, CONTROL Sec. 4 discusses ground water as a mineral resource. This section deals wits its control. 26.1.1-IMPORTANCE Flows of water have an important effect on the cost and progress of many deep excavations. The existence of water limits the methods which can be used in some and presents hazards in others. Lowering the water table may reduce the flow of springs and wells, with legal liability. Some mine water is used directly, some must he treated before discharge, and some contains dissolved solids which can be recovered profitably. Loss of life, property and production from flooding is grim, yet scores of mines have worked safely for generations under ground-water reservoirs, lakes and even the sea. The need for better control of mine water is measured by the severity of recent floodings, concern with the quality of the effluent, and direct and indirect costs of working wet ground. There are improvements in freezing in shaft sinking. pumps and their controls, treatment of mine water before it is pumped, bulkhead construction and certain efforts to reduce inflow. 26.1.2-PUMPING COST VS. COST OF WET WORK Direct operating and capital costs of pumping are more evident than indirect items, such as provision of extra standby power and maintenance facilities, The total of all these items is the cost of pumping water from an excavation. This is only a part of the extra cost of working wet as compared to dry ground. Less productive methods, less efficient equipment and more expensive explosives may have to he used in wet work. Wet rock plugs certain equipment. Maintenance is higher and labor less efficient. The cost of any means of keeping work drier should he weighed against the higher cost of working wet. The true difference in the cost of working wet ground, compared with dry, probably is known at only a few places (see checklist of cost items. Sec. 26.4.13). An extreme comparison of mining wet and dry ore is available from Ambrosia Lake, N.M. (Fig. 26-1). Between 1963 and 1967, a wet and a dry mine were worked by the same company under conditions otherwise comparable. Average operating cost at the wet mine, pumping 1,600 to 1,800 gpm. was $16.06 per ton of ore. The comparable figure for the dry mine was $7.50. Principal differences included the fact that the wet mine was worked from drainage levels below the, ore with rail haulage, the dry mine in the ore with off-track equipment loading and hauling to the shaft. In the wet mine, ore packed in chutes, cars and skips and froze in surface bins, stockpiles and trucks. Wet-mine costs included drilling drain holes, building and maintaining ditches and pumping water containing abrasive solids.

Jan 1, 1973

By A. K. Sinha

Despite the tremendous efforts and costs incurred by the industry and regulatory agencies to prevent premature roof failures in underground mines, roof falls continue to occur frequently due to the very unpredictable geological conditions and dynamic nature of mining operations. In fact, roof falls continue to be the largest contributor to coal mine fatalities. The failure of a mine roof generally occurs following a prolonged, gradual degradation in its physical conditions. An electronic mine roof monitoring system has been developed and tested in operating mining sections. It monitors mine roof degradation on a continuous basis. The field test results are presented and discussed.

Jan 1, 1987

Just 104 km (65 miles) from Phoenix, AZ, Rio Tinto hopes its new Resolution Copper Mine will be a showcase for the Rio Tinto management philosophy. Its goal is to have a net positive impact. In every place that Rio Tinto mines, it wants to be able to have an overall beneficial effect on the local community, environment and economy. ?We?re constantly working to understand our impacts, to understand how to minimize our impacts and understand how to mitigate those impacts,? said Resolution Copper Mining chief executive officer David Salisbury, from the global headquarters of Rio Tinto Minerals in Green-wood Village, CO.

Jan 1, 2010

By Ananta L. Yennamani

Blast movement measurement (BMM) transmitters are a practical method to measure three-dimensional (3D) rock movement because of blasting. The BMM transmitters are activated, programmed and installed in specially designed drill holes prior to the blast and the BMM detector locates the transmitters after the blast. The BMM software then calculates and summarizes the 3D movement of each BMM transmitter ball. This information helps to redefine the ore and waste boundaries and enables improved ore and waste selection, resulting in a genuine step change in grade control. The BMM program was carried out at Newmont Mining Corp.?s Phoenix Mine, in northern Nevada near the town of Battle Mountain. The mine is in a historic mining district that contains gold, silver and copper. The geology of the pit consists of different formations made up of sandstone, siltstone, limestone, chert-pebble conglomerate, shale, skarn and quartzite, to name a few. Some of the rock is extremely hard and a powder factor of up to 0.5 kg/t (1 lb/st) is required to get adequate fragmentation to ensure sufficient throughput through the crusher and the mill. The result of using such a high powder factor translates into considerable blast movement and heave. This movement means that the ore/waste digging polygons estimated by the ore control engineer from sampling the initial blast holes will no longer be located in their original posi-tions. The purpose of this project was to test the measurement method and to see if locating the digging polygons in the broken muck pile and excavating to those polygons will improve grade control through the mill. Case studies (Zhang, 1994), (Taylor, 1995), (Gilbride, 1995), (Harris, 1997), (Taylor, 2003), Barrick Goldstrike (Gold-strike Mine, 2008), Ruby Hill Mine (Hilkewich, 2009), (Porcupine Mine, 2005) and (Aguirre, 2010) have shown that, by accounting for the blast movement, there is a potential to increase mineral recovery by as much as 25 percent for individual blasts for only a modest cost increase.

Jan 1, 2011

By D. S. Bird

Kennecott Utah Copper began a modernization program in 1986 that was aimed at expanding and updating mining and ore process facilities at the company’s Bingham Canyon copper mine and concentrator near Salt Lake City, UT. Major components of the project included installation of an in-pit crusher, a transfer conveying system and a new ore concentrator with a design capacity of 70 kt/d (77,000 stpd). The Copperton concentrator was commissioned in February 1988. The grinding circuit is one of its principal features. It consists of three identical lines, each with a 10.4-m- (34-ft-) diam x 4.6-m- (15-ft-) long semiautogenous grinding (SAG) mill and two 5.5-m- (18-ft-) diam x 8.6- (28-ft-) long ball mills. The SAG mills are driven by two 4.5-MW (each) (6000-hp) variable- speed dc motors through a clutch-pinion gear-ring gear assembly. The ball mills are driven by 4.1-MW (5500-hp) synchronous motors coupled through a typical clutch-pinion gear-ring gear system.

Jan 1, 1995

By Charles E. Weaver

A core from the La Camelia attapulgite mine in north Florida was studied in detail to determine the detailed vertical variability and the relations of the various parameters. The structural, textural, mineralogical and chemical data indicate there are two major depositional cycles represented within the minable interval. The sediments deposited during the two cycle differ in detail but in general are similar. The environments of deposition grade from shallow marine to lagoonal to tidal flat to marsh. The sedimentary structure (lamination, burrows, pebble conglomerate), mineralogy (attapulgite, montmorillonite, sepiolite, dolomite, calcite) chemistry (Al, Mg, Fe) are closely related to each other and their nature is determined by the depositional environments. Most of the clay minerals and carbonate minerals are authigenic and are therefore particularly sensitive to environmental differences. The variability and environmental features seen in this core are characteristic of the sediments in the general attapulgite mining area. A detailed understanding of the relationships discussed should be of value in prospecting, mining and processing.

Jan 1, 1972

By Richard L. Bullock

INTRODUCTION TO COAL MINE PRACTICES To illustrate the trends and the proportions of the various methods used to mine coal underground, Fig. 1 is useful. However, of all the underground coal mining practices in the US, room-and-pillar mining still accounts for 96.5%. This percentage is divided as follows: conventional, machine cut-33.0%; conventional, hand cut -1.7% : and continuous mining-61 .8%. As was stated in Sec. 1, Chap. 7, the term "development" means different things to a coal miner and a metal miner. Though some of the ideas and concepts presented in the first two chapters of this section are valid for all types of mines, they apply particularly to mines using noncoal methods. In coal mines (and many other mines using coal mining systems) development refers to that phase of the mining cycle which advances several entries through the virgin seam, forming pillars by cross- cutting between the parallel entries. Because in the past, coal seams (as well as seams of potash, trona, oil shales, gilsonite, salt, and some uranium) have been much more uniform in their thickness, continuity, and quality, and because they often cover large areas, it has been possible to develop the room-and-pillar mine completely from a preplanned, systematic approach with a minimum of surface drilling information. As the better coal seams of the midwest and east are being depleted (or eliminated because of high sulfur), seams of poor quality and continuity will have to be mined. Also, seams that are not nearly so well known at greater depth will have to be taken as well as some of the steeply pitching and folded seams of the west. The American coal miner is only now feeling the need to do a much more complete job of prospecting the geology of the coal seams than he has ever done before. This is the only way that the risk of unknown rock conditions can be minimized. In many ways, surprises in the rock or coal seams are much more of a disaster to the coal miner developing a room-and- pillar mine than to his metal mining counterpart. Be- cause of the multiple entries, the complex set of the Federal Coal Mine Health and Safety regulations, and the totally dedicated design of coal mining equipment, coal mining systems do not have the flexibility to easily overcome changes in the seams mined or the rocks around them. Thus, if a wide parting of rock shows up unexpectedly in the middle of a coal seam entry being milled away by a continuous miner, it will either have to slowly "chew" through it, convert to a conventional mining system, or stop that particular entry. Likewise, if suddenly the coal disappears completely and in its place are the remains of an old creek bed, the "want" or "wash out" as it's called will usually have to be mined right along with the coal, by the same methods and with the same soft rock equipment, or the entry will have to be abandoned. For reasons such as these, coal seams today should be drilled from the surface just as thoroughly as the ore bodies in metal mines. Having once determined a more precise location of where the coal seams are located and which are suitable for mining, the engineer must still take a systematic approach to planning the mine as completely as possible. The initial series of entries must be planned to be driven either from the side hill portal or from the bottom of the shaft or slope. In either case, they should usually intersect the area close to the midpoint of the mass to be mined.

Jan 1, 1982

By Y. Luo

"Investigating abandoned mine subsidence is often a difficult task because many factors, both mining- and nonmining-related, can affect the possibility and the formation process of surface subsidence events over abandoned underground room-and-pillar mines. Among them, mine water frequently plays an important role in causing such subsidence events. However, mine water could also serve the purpose of preventing subsidence. The dewatering of abandoned room-and-pillar mines has been identified as the main cause for a number of serious mine subsidence events in the past.In this work, the mechanism of mine water to prevent surface subsidence over abandoned room-and-pillar coal mines was studied. Two mathematical models are proposed to quantify the potential effects of mine water on the structural stability of mine pillars, roof and floor as well as the potential for causing surface subsidence. The models are validated with an actual case. IntroductionThe potential for room-and-pillar mining operations to induce surface subsidence is mainly dependent on the recovery ratio in the underground mines that directly relates to the stability of pillars. Normally, if the recovery ratio is less than 50 percent, the mine pillars are sufficient to support the overburden strata without their collapse in a sufficiently large contiguous area. Consequently, there will be no surface subsidence. However, if the recovery ratio is greater than 70 percent, the pillars are too small to support the overburden strata and can cause immediate surface subsidence. In 1993, a mathematical model and program was developed and proposed (Luo and Peng, 1993) to predict surface subsidence caused by high-extraction, roomand- pillar mining. When the recovery ratio is between 50 and 70 percent, the mine pillars could be loaded near their critical condition and, therefore, the surface subsidence is uncertain to develop. If the surface subsidence did not occur immediately, mine water starts to fill the underground openings. If thick, clay-type rock layers are presented in the mine roof, floor or pillars, they can be considerably weakened by mine water and cause surface subsidence. The techniques to investigate subsidence events over inactive room-and-pillar coal mines caused by the weakening effects of raising mine water to the claystone immediate roof and floor were presented in Luo (2009, 2011)."

Jan 6, 2018

By Joseph S. Malesky

The discovery and development of explosives mark one of the most important findings in the history of civilization. Without explosives our vast economic enterprise concerning the mining of coal, copper, iron, aluminum, and various other ores could not function. Explosives are used in all kinds of construction works, in the razing of old buildings, blasting of trenches, driving of tunnels, and in many other instances common to our everyday life. For these reasons explosives are rightfully referred to as the forerunner of progress. An explosive may be defined as a substance (usually a mixture) that, when flame or shock is applied, yields readily to rapid combustion or oxidation, accompanied by the formation of such relatively large quantities of gases as to produce much violence and pressure which, in turn, react against their surroundings and cause what is termed an explosion. By their very nature the action of explosives is destructive and disruptive of adjacent materials. Decomposition of explosives can occur through deflagration, which is rapid burning or combustion, as in the case of black powder, or through detonation, which is an almost instantaneous disruption, as in the case of dynamites and blasting agents.

Jan 1, 1981

By J. Casado

This paper presents the results of an analysis and summary of relevant literature on the mechanism of cementation of metals in acidic aqueous media, with the aim of reconsidering the conventional assumptions. The simplicity of the process as a mere galvanic metal displacement is discussed, and the real effects of pH and hydrogen pressure in different cases assessed. Finally, an alternative mechanism scheme with respect to the role of hydrogen species, in agreement with reported data, is proposed.

By L. P. Johnson

Longwall mining has gained acceptance as a safe method of maintaining coal production where conventional systems were unsuccessful or uneconomic due to bad roof conditions (Kuti8). One of the major problems confronting American operators involves the correct choice of equipment which should be selected to suit the local mining and geologic conditions for optimum productivity. To achieve this, factors such as rock strengths, local geology, panel geometry, and panel orientation must be examined to optimize production and minimize down time due to ground control problems. Little quantitative information is available in the literature regarding the effects of geologic conditions on American longwall operations, and past implementations of longwall systems appear to have been based largely on experience. When mining engineers are able to assess the geologic conditions both quantitatively and qualitatively, they can more fully optimize equipment selection and panel design.

Jan 1, 1977

By Jerry C. Tien

The rare earth elements (REEs) are a group of 17 chemical (metallic) elements. REEs are used widely in high-technology, clean-energy products as well as weapon systems. China's dominant position as a producer of over 95% of the world REEs output and the world's increasing reliance on REE products have highlighted concerns about the future availability of rare earths in recent years. This paper briefly reviews the REEs world reserves, production, consumption, the impact of our heavy reliance on REEs products and China's changing policies on REE export on world supply chain.

Jan 1, 2013

By K. Baba

Liberation of valuable minerals from a gangue matrix during size reduction of multiphase mineral particles is an important objective in mineral separation processes. A methodology for the prediction of volumetric grade distribution from one dimensional, linear intercept image analysis is being developed using a transformation function to describe the relations hi p between the linear and volumetric grade distributions. As part of this research effort it has been found that a transformation function, derived from Monte Carlo simulations of irregularly shaped particles, mainly depends on the volumetric grade and the dispersion density, i.e., the number of nuclei (or grains) per particle. A possible mathematical form for the transformation function is described in detail.

Jan 1, 1985

By William L. Barnes, Maurice Leiser

INTRODUCTION The literature on project management considerations and techniques for large rail rapid transit projects in mid-1979 was fairly large and getting larger. UMTA was establishing special organizational elements to deal with the subject as it related to those properties requesting capital assistance, and comprehensive project management plans were being requested from those properties as an early step to build confidence in UMTA that the particular project could be planned, designed, and executed efficiently and effectively, thereby using critically short capital assistance funds to best advantage. In the late 60's and early 70's, the choices of models for heavy rail construction would have been quite limited.., and perhaps much simpler than was the case in 1979. One of the writers was with an agency in 1979 in the process of finalizing its organization for project implementation after several years of study and had the opportunity to review the experiences of others at length, presumably to build on the success and to try to avoid the pitfalls and failures. The properties that were surveyed all reported more or less success stories. One could only conclude that there are many ways to organize for a major transit (construction) project and that there is a great variety of viable management structures, but it seemed that chances for success were best where the executing property had prepared a comprehensive project management plan, then resolved to follow it. Perhaps more important, a commitment or prior approval had been sought from UMTA as to the validity of the project management plan, and the property was allowed to proceed without detailed prior UMTA review or approval of all specific intermediate steps. Most important, however, an early overall UMTA funding commitment had been obtained that permitted some reasonable expectation of the rate of funding, perhaps by commitment

Jan 1, 1981

By James Parkes

"The proposed Baltimore Red Line light rail system includes a 3.4 mile downtown tunnel (DTT) with five underground stations. The design of the underground stations involved overcoming several challenges, including limited right-of-way, high groundwater and uplift pressures, and metamorphic rock within the station depths. An innovative design was developed to maximize the internal station space while minimizing cost. The station designs use slurry walls for temporary and permanent support and groundwater control. Depths within rock are supported with cast-in-place concrete walls, the thickness of which are minimized through the use of permanent rock anchors for support of the rock mass and slurry wall toes. Permanent tiedown anchors are used for uplift resistance, which minimizes the station depths, volume of rock excavation, and the volume of deadweight concrete. Design considerations regarding individual elements and overall integration of the slurry walls, CIP walls, and multiple anchor types are presented.INTRODUCTION The Baltimore Red Line (BRL) project is a proposed light rail transit line for the Maryland Transit Administration (MTA) that runs east to west through Baltimore City and County. The project includes the Downtown Tunnel (DTT) consisting of 3.0 miles of twin running tunnels, two portals, five underground stations, and a pedestrian tunnel, as shown in Figure 1. The tunnels have an outside diameter of 21.8 feet and are designed to be mined using pressurized face tunnel boring machines (TBMs). The stations, portals, and the pedestrian tunnel are designed as cut-and-cover structures using slurry walls (concrete diaphragm walls) for both temporary support of excavation (SOE) and permanent structural walls. The dimensions of the five underground stations are summarized in Table 1. Design challenges included limited right-of-way (ROW), challenging soils conditions, strong metamorphic rock within the station depths, and high groundwater conditions. The final station designs included innovative use of slurry walls, tieback anchors, rock anchors, and tiedown anchors."

Jan 1, 2016

By M.P. ROY, ASHISH K. VISHWAKARMA, A.K. MISHRA, P.K. SINGH, VIVEK K. HIMANSHU

Principal component analysis (PCA) is one of the dimension reduction techniques widely used to classify data based on features. Ground vibration is a major hazard arising from rock blasting operations, and accurate prediction of the vibration is necessary for designing controlled blasting parameters. Most of the widely accepted predictors of ground vibration consider the maximum explosive charge weight per delay (MCPD) and distance as the parameters responsible for ground vibration, but mining sites with bigger production targets have varying geometrical parameters to suit the excavator utility. Accordingly, other blast design parameters will also have impacts on ground-vibration intensity. A blast vibration predictor considering all the blast design parameters would be complicated, and some of the parameters will have overlapping contributions to ground-vibration intensity. Data classification using PCA is a feasible solution, and regression analysis may be performed to develop predictors using the classified input data. In this study, PCA was used along with multivariate logarithmic regression to predict ground vibration, and the performance of this technique to predict ground vibration was compared with the performances of various existing empirical predictors. The evaluation suggests that the predictor with logarithmic regression followed by PCA performs better than the existing empirical predictors.

Nov 1, 2022

By William H. Langer

Nearly every community in the United States is dependent on aggregate (sand, gravel, and crushed stone) resources to build and maintain its infrastructure. Unfortunately, developing aggregate resources to meet societal needs causes environmental impacts. Most environmental impacts associated with aggregate mining are benign. Extracting aggregate seldom produces acid mine drainage or other toxic effects commonly associated with mining of metallic or energy resources. The most obvious environmental impact of aggregate mining is the conversion of land use, most likely from undeveloped or agricultural land use, to a hole in the ground. This major impact is accompanied by loss of habitat, noise, dust, blasting effects, erosion, sedimentation, and changes to the visual scene. Some of the impacts are short-lived, and most are easy to predict and easy to observe. Most impacts can be controlled, mitigated, or kept at tolerable levels and can be restricted to the immediate vicinity of the aggregate operation by employing responsible operating practices and available technology. The intensity of environmental impacts generated as a result of mining are determined in large part by the geologic characteristics of aggregate deposits (geomorphology, geometry, and physical and chemical properties). Mining deposits that are too thin, or contain too much unsuitable material, results in the generation of excessively large mined areas and large amounts of waste material. Mining aggregate can lead to serious environmental impacts in some situations. Some geologic environments such as active stream channels, slide-prone areas, and karst terrain are dynamic and respond rapidly to outside stimuli including aggregate mining. Some geomorphic areas and (or) ecosystems underlain with aggregate serve as habitat for rare or endangered species. Similarly, some geomorphic features are themselves rare examples of geologic phenomena or processes. Mining aggregate might be acceptable in some of these areas, but should be conducted only after careful consideration, and then only with extreme prudence. Failure to do so can lead to serious, long-lasting, and irreversible environmental consequences, either in the vicinity of the site or at locations distant from the site. Environmental impacts caused by irresponsible aggregate mining can compromise mining in an entire region.

Jan 1, 2001

By Yueyue Ding, Yuanhui Li, Zhengrong Li, Pengfei Yu, Kunmeng Li, Zhipeng Xiong

The overburden responses in gently inclined orebody mining are different from those in horizontal orebody affected by the orebody dip angle. In particular, the mining-induced stress presents asymmetrical distribution characteristics spatially, resulting in stress concentration and large-scale pressure relief phenomenon in the surrounding rock. As a result, frequent ground pressure disasters such as roof collapse and barrier splitting occur frequently. Moreover, the ground pressure evolution law and the interaction between stopes in multistope mining are complex. The effective ground pressure control measures cannot be taken due to unclear understanding of the evolution of stress and displacement fields, justifying the investigation of the distribution and evolution of underground pressure for safe and efficient mining.

Jun 1, 2023