Search Documents

By Brian Gettinger, Jared Barber, Richard Weatherly, Shannon Dunne, Jeff Masek, Chuck Wolf, Fazle Rabbi, Jack Canfield

During Hurricane Harvey over 60% of the 39 WWTPs, including the low-lying 25 MGD Sims North WWTP, and one third of the 382 lift stations owned and operated by the City of Houston were flooded resulting in extensive facility damage, loss of service and uncontrolled release of untreated wastewater into bayous and creeks. In response, the City has embarked on an effort to improve system resiliency by consolidating at-risk facilities with a network of deep sewer tunnels. These tunnels will provide secondary benefits to the collection system of augmenting the capacity of the existing 6,000 miles of sewer mains and lowering the collection system profile in poor performing areas. Investigations on the cost to mitigate the flood damages by raising the liquid stream processes at the Sims North WWTP is estimated at nearly $450 million. Instead of spending $450 million to raise the plant, the funds will be directed to providing a more robust and resilient wastewater system for the Sims basin area of Houston. The backbone of this new system is a 4.5-mile-long, 110 inch diameter deep gravity sewer tunnel that will convert a system heavily reliant on distributed lift stations to a majority gravity system with a deep consolidated lift station at the Sims South WWTP. This will also allow the City to address the flood prone infrastructure at Sims North and consolidate its operations into a single permitted outfall for this collection system. This approach is the outcome of a team effort focused on maximizing system resiliency and sustainability for the next 100 years. By thinking outside the box, the City of Houston will not only mitigate the flooding risk at Sims North WWTP, but also solve regulatory and operational challenges throughout the sewershed and deliver a winwin on multiple levels.

Jun 13, 2021

By Corey Vaughan

Unplanned shutdowns from abrasive wear part failure in crushers, chutes, and slurry pipe assets can cost millions in lost production and reactive maintenance. 2Censor patented sensor technology enables real time abrasive wear monitoring of mineral processing equipment, turning passive assets into smart, data driven components. Wireless sensors embedded in liners and pipework transmit wear data live to operators, allowing for predictive maintenance, safer scheduling, and optimized asset life. This paper will present global case studies showing reductions in downtime, increased throughput, and improved maintenance accuracy. The system is ready to retrofit, neutral to original equipment manufacturers, and proven across more than twelve countries in abrasive wear liners and slurry pipe applications.

Feb 22, 2026

By O. M. Johnson

Barite and bentonite are the two principal components of drilling fluid systems used in the petroleum industry for oil and gas well drilling with rotary-type rigs. Approximately 87 percent of the world's annual production of barite is used in drilling applications. Of the worldwide production of bentonite, an estimated 30 percent is used. The drilling fluid, or drilling mud, to which barite and bentonite are added, performs five distinct functions: Lubrication-The liquid phase of the drilling mud lubricates the drill bit, preventing premature failure of the cutting edges and bearings. it also helps to soften the formation being drilled. Cuttings Removal-A mud system must be able to carry rock cuttings broken loose by the bit up to the surface where they can be removed by mechanical or chemical methods. The fluid's ability to perform this function depends upon maintaining a proper balance between the rate of circulation of the fluid and the colloidal properties required to entrain the cuttings in the mud to prevent their settling to the bottom of the hole. Hole Stability-The pressure exerted by the mud against the wall of the bore hole prevents the collapse of the uncased portions of the hole. Downhole Information-The fluid characteristics of the mud should be such that good cuttings samples, cores and electric logs may be obtained to help evaluate a well's productive zones and potential. Control Oil, Gas and Water Flows-It is essential that a drilling fluid offset any pressure from naturally occurring formation fluids in order to prevent a potentially wasteful and dangerous blowout.

Jan 1, 1980

By Y. Xi

In this paper we present an availability approach for determining the capacity of a major bucket wheel excavator (BWE) system to be used in Yuabaoshan surface coal mine in China. Based on previous time studies on other BWE systems for delay times due to internal and external causes, and a four-level maintenance and repair schedule, we develop a model taking into account all random failures and present a fast and simple solution to this highly complex problem. A procedure employing the Markov renewal theory for determination of the distribution of random failure times and failure rate of the whole system, as well as some other factors useful for calculation of the overall system capacity are discussed in the paper.

Jan 1, 1993

By R. Schlüter

"The “Biohydrometallurgical Center for Strategic Elements (BHMZ)” is a cooperation of 13 departments of the Technical University Bergakademie Freiberg fostering interdisciplinary research along the whole (bio-) hydrometallurgical process chain to extract indium and germanium from sulphide ores. Research comprises methods to (i) bring the respective metal from the source material into aqueous solution and (ii) different approaches to extract pure metal or metal-containing materials from the solution. Within the BHMZ the Department of Underground Mining Methods deals with the design and implementation of an underground testing facility for bacterial in-situ stope leaching in its own “Research and Educational Mine”. The intention is to investigate innovative approaches for leaching technologies by crack initiation due to hydraulic fracturing or water pressure blasting under consideration of leaching kinetics and underground conditions. It is planned to set up two testing units comparing energy input and the metal output of conventional (blasting) as well as one of the innovative technologies. Aim of subproject is to establish an innovative and sustainable method ready for up-scaling. BACKGROUND Metals like copper and zinc mainly occur as sulphide ores in nature. Due to the insolubility of these sulphide minerals the respective metal is commonly extracted by pyrometallurgical processing methods. These methods require several steps of enrichment of concentrates such as flotation and roasting (Figure 1) under extensive energy utilization. Additionally, this arouses the emission of sulphur dioxide gas which can have a negative impact on the environment in form of acid rain, as long it is not caught by sulphuric acid facilities (Schippers et al. 2011). However, to treat the ore on the surface either open pit or underground mining operations are necessary. This implies operation steps from excavating, loading, and conveying/hauling, to dumping with the sub-processes crushing and stashing. Due to the tendency of increasing depth, more complex ores and decreasing ore grades of the mineable deposits as well as increasing energy and environmental costs these conventional mining and processing methods become in general more costly and difficult to apply. Hence, hydrometallurgical processes and especially the suitability of bioleaching as an alternative in-situ method for future mining projects should be examined. Leaching by means of microorganisms is a combination of mining and processing by converting the insoluble metal into an aqueous form. This technology is an economically beneficial and environmentally friendly alternative to pyrometallurgical processing methods especially for primary and secondary low grade ores. Mainly the extraction of copper but also of zinc and lead from sulphide ores is state-of-the-art in surface leaching operations like heap and dump leaching (Figure 1)."

Jan 1, 2015

By E. K. Albert

In 1977, Congress enacted Title IV of the Surface Mining Control and Reclamation Act (SMCRA), providing for an "abandoned ml.ne reclamation fund". This fund, taken from a fee collected from operating coal mines, provides capital for the reclamation process. However, given the number and extent of abandoned mine sites in some states, the question of project selection is important. This paper describes a project in progress to create a Management Information System application for project ranking under multiple objectives. The benefit of this project for the need of new environmental control technologies will be discussed.

Jan 1, 1990

By Fiona Woody

Lime and calcium products are essential building blocks to the modern world, used to purify drinking water, preserve foods, control pollution, improve crop yields, stabilize soil, pave roads and support the production of steel, cement, glass and many other industrial processes. While lime is essential to society, it also has a sizable carbon footprint. Approximately 30 percent of the scope 1 greenhouse-gas emissions generated during lime production are related to fuel combustion, while the remaining 70 percent are created by the unavoidable chemical reactions during calcination.

Feb 1, 2026

By Joseph H. Herz

Recently, the President of the Portland Cement Association, Robert D. Maclean, gave the keynote address at the Rock Products Eighth International Cement Industry Seminar. He said, after listing the seven plagues our industry is suffering, "none of these items I have listed is a sales or marketing problem. Further, none is a problem that can be relegated to long-term study by public or private research agencies. They are here-and-now problems to be faced daily by producers, researchers, equipment manufacturers and consultants. THE DAY OF THE PRODUCTION MAN IS HERE." (1)

Jan 1, 1973

By Samuel Rigert, Marco Bettelini

"INTRODUCTION AND OBJECTIVES Long rail tunnels require in most cases powerful mechanical ventilations. Besides requirements related to normal operation and maintenance, operational safety always requires a high level of smoke management. Identifying the optimum ventilation concept is essential for achieving proper performance and safety while keeping investment and operational cost at a reasonable level. For the purpose of the present paper, long tunnels have a length of typically 20 km or more. This is related to the European classification of trains (TSI 1303/2014), where the maximum distance from the portals to a firefighting point and between firefighting points is limited to 20 km (only category B passenger rolling stock allowed) or 5 km (general case). From TSI 1303/2014 it can be concluded, that tunnels over 20 km require in any case emergency stations with complex mechanical ventilations. Based on the experience arising from a number of recent projects in the European area, including in particular Gotthard (GBT), Lötschberg, Lyon-Tourin (LTF), Brenner (BBT) and Gibraltar, safety-relevant issues related to the ventilation of long railways tunnels are reviewed in this paper. Amberg Engineering is directly involved in these challenging design tasks and can provide first-hand experience and know-how. As a particular highlight, special attention is devoted to the longest tunnel worldwide, the 57 km long Gotthard Base Tunnel, which will be commissioned in 2016. THE GOTTHARD BASE TUNNEL Overview The Gotthard Base Tunnel will be commissioned in 2016 (official inauguration on the 1st of June and beginning of regular operation on the 11th of December) and will be the worldwide longest tunnel. Its complex and powerful ventilation system is very representative for many other long tunnels and is used as reference in this paper. Therefore, a few key characteristics of the Gotthard Base Tunnel and its ventilation system will be described in some detail in this initial chapter. The Gotthard Base Tunnel (GBT) consists of two single-track tunnel tubes with connecting galleries every 312 meters. Two so-called multi-functional stations (MFS), located at roughly 1/3 and 2/3 of the tunnel length, host the key equipment for normal and for emergency operation. At these locations, double crossovers allow trains to switch from one tunnel tube to the other. An emergency station is located in each multifunctional station, allowing trains to stop in case of emergency. The general layout of the GBT is presented in Figure 1."

Jan 1, 2016

By S. K. Kawatra

Many mineral oxide and multi-component oxide (basalt) specimens break down into powders upon expo-sure to sodium vapor at elevated temperatures for extended times. This paper examines several possible mechanisms of oxide breakage by sodium vapor, both experimentally and from a thermodynamic viewpoint. The oxides for which reduction by sodium was thermo-dynamically favorable all exhibited some degree of fragmentation. The oxides which were not favorable for reduction by sodium did not exhibit fragmentation, with the exception of rutile, a titanium oxide. The rutile fragmentation was caused by the reduction of iron that was in solid solution in the rutile crystal structure.

Jan 1, 1995

By Jr. Raleigh

In a cooperative agreement between the U.S. Bureau of Mines and the U.S. Department of Energy, laboratory column-flotation tests were conducted to evaluate fluorosurfactants as selective fine coal flotation collectors. A Middle Kittaning seam coal responded to flotation with both anionic and nonionic fluorosurfactants. These fluorosurfactants were no more selective than MIBC alone. However, for increasing coal yields, nonionic fluorosurfactant systems did not increase total sulfur and ash contents as sharply as MIBC systems. Flotation selectivity also improved slightly when a combined anionic fluorosurfactant-MIBC system was used in acidic pulps (pH < 3.6). While the fluorosurfactants examined will not likely have direct application in current coal flotation practice, other fluorosurfactant systems could eventually prove beneficial for floating fine coals.

Jan 1, 1990

By Igor Gonzales G.

Southern Peru Copper Corporation (SPCC) has recently completed the construction of copper leaching, solvent extraction, and electrowinning facilities at their Toquepala and Cuajone plants in Southern Peru. Much of the ore for these new operations is the result of the existing mining operations that have been in existence as early as 1959. At Toquepala, pre-conditioning and bacterial dump leaching of the sulfide ore that was too low in copper content to be processed through the copper concentrator began in 1987. The Cuajone heap leach operation is treating copper oxide ore that has been stockpiled since the Cuajone concentrator began operation in 1976. The pregnant leach solutions from the dump leaching at Toquepala and the permanent pad heap at Cuajone are combined into one plant feed solution. Adjacent to the large dumps at Toquepala, a solvent extraction and electrowinning facility has been constructed. The electrowinning facility has a planned annual production rate of35,000 metric tons per year Grade A cathode copper. Initial production of the cathode copper began in November 1995.

Jan 1, 1996

By M. A. Reyes, L. Yan

Heat and humidity buildup withn refuge alternatives (RAs) may expose occupants to physiological hazards such as heat stress. The Mine Safety and Health Administration (MSHA) regulations require RAs in underground coal mines to provide a lifesustaining environment for miners trapped underground when escape is impossible. RAs are required to sustain life for 96 h while maintaining an apparent temperature (AT) below 95 °F (35 °C). The National Institute for Occupational Safety and Health (NIOSH) tested a 10-person tent-type RA, a 23-person tent-type RA, and a 6-person metal-type RA in its underground coal mine facilities to investigate the thermal environment over a 96-h period. The test results showed that mine air and mine strata temperatures surrounding an RA occupied by simulated miners (SMs) increased over the 96-h test period. The test results suggest that RA manufacturers should consider this increase in temperatures when calculating and evaluating RA components during surface and laboratory tests. The findings can equip stakeholders with additional considerations for calculating the interior heat and humidity temperature profiles for occupied RAs not tested in situ.

By Kenneth J. Miller

A novel two-stage froth flotation process to remove pyritic sulfur from fine- size coal is described. The process consists of a first-stage, standard coal flotation step in which high-ash refuse and some of the pyrite are removed as tailings. The first-stage clean coal froth concentrate is then repulped in fresh water, and a coal depressant, a pyrite collector, and a frother are added to float the remaining pyritic material. Laboratory and pilot plant flotation results with coals from the Lower Freeport and Pittsburgh beds are given. The pilot plant test results show that up to 80 percent pyritic sulfur reduction was achieved with the Lower Freeport bed coal and up to 50 percent with the Pittsburgh bed coal. Laboratory and pilot plant results were in excellent agreement, indicating that the process is a viable means of removing much of the sulfur from some coals.

Jan 1, 1974

Extensive testing in the past ten years has shown that where a uniform natural gamma background is present in the strata bordering the seam, the thickness of the boundary coal left in place after mining can be determined by measuring the attenuation of that radiation (Nelson and Bessinger, 1989). Measurements made by the authors in underground mines in Pennsylvania, West Virginia, Ohio, Illinois, and Kentucky, and by others in Wyoming and New Mexico, have shown the presence of such a gamma background (Nelson, 1989). Natural gamma coal thickness sensors of several configurations have been tested in mines owned and operated by the Consolidation Coal Company in Pennsylvania and west Virginia (Nelson and Bessinger, 1988).

Jan 1, 1990

By James A. Curry

Table I identifies the maximum cost of the individual provisions with spoil disposal in Appalachia leading at $3.98 per ton, This was followed by deep mine subsidence control and monitoring at $1.66 per ton. At the request of the U.S. Department of Energy, the Bowser-Morner Testing Laboratories of Dayton, Ohio, evaluated Consol&apos;s cost estimates for 14 of the 21 regulatory provisions the company studied. It is interesting to note that Bowser-Morner concluded that Consol&apos;s estimates of costs were very conservative and that the actual costs will be substantially higher than what the company reported. In 1978 a joint committee of the National Coal Association and the American Mining Congress made estimates of cost impacts under 11 OSM permanent rules (see Table II). Six rules applied to mid-western strip mining were projected to cost $6.52 to $17.17 per ton. Five rules applied to mid-western strip mines showed costs ranging from $.91 to $6.11 per ton. Three rules applied to deep mines (regardless of region) were seen raising costs from $ .57 to $2.67 per ton. The joint committee reported trouble developing overall figures because member firms used widely different assumptions in calculating their costs. That same statement could no doubt be made when comparing most cost data available today.

Jan 1, 1980

By H. Walqui, S. K. Kawatra, C. H. N. Jeltema, T. C. Eisele

"The literature contains many cases where the shape of hydrocyclone efficiency curves vary from the ideal “S” shape. These often appear as changes in slope, or inflections. These inflections can be divided into two categories: “coarse” inflections, which are caused by differences in the density of the minerals being separated, and “fine” inflections, for which there are a number of competing hypotheses concerning their cause. The existing literature addresses either the fine inflection or the coarse inflection, but no studies have reported both types of inflection occurring at once in a single hydrocyclone test. This paper presents hydrocyclone results from both in-plant studies and laboratory experiments that show both coarse and fine inflections. The industrial significance of both types of inflections is discussed. Hydrocyclone efficiency curves show the probability of any given particle reporting to the hydrocyclone underflow as a function of its size. Selectivity functions, S(d), are used to represent the fraction of the feed material in size fraction “d” that reports to the hydrocyclone underflow. Plotting this selectivity function against particle size leads to the standard S-shaped efficiency curve shown in Fig. 1. In the “uncorrected” curve, the tail of the curve does not go through 0%, because a portion of the solids are bypassing classification. This happens as a result of their being carried along by the water, and is most important for the finest particles. The curve can be “corrected” based on the fraction of the feed water that reports to the underflow, represented by the bypass fraction, Rf. The corrected curve then normally passes through 0%, as shown in Fig. 1.The act of correcting the curve shifts the value of the d50 size, which is the size that has an equal probability of reporting to either the overflow or to the underflow. Correcting the curve to account for the bypass fraction makes it easier to compare cyclone performance under conditions that cause the quantity of water in the underflow to change, but that do not alter the actual corrected cut size (d50c).The corrected efficiency curve can be expressed closely by equations such as Plitt (1976):"

Jan 1, 2015

By Dolf W. Fieldman

Most recently the geologic setting of the mineral deposits in the Silver Cliff district is described by William M. Sharp in ?Geologic Map of the Silver Cliff and Rosita Volcanic Centers, Custer County, Colorado?, (U. S. G. S. Map I- 1081). The discussion will relate only to the southern half of the Silver Cliff volcanic center and differences in geologic interpretation, which are largely structural, will be pointed out as they arise. Only the manganese/silver zone of the Kate Area will be discussed in detail.

Jan 1, 1980

By Hubert E. Risser

At the outset of a discussion on the adaptability of Illinois coals for use in iron and steel production, it is perhaps well to define terms. ?Adaptability? as used in this context, means that a coal can be, adapted to use within a given technological and economic framework. For a coal to be adaptable, to use in the manufacture of metallurgical coke within the present technological and economic framework, it must possess, among other things, at least the following characteristics: 1. The coal must be capable of producing, alone or in combination with other coals, a coke that can meet at least a minimum standard of required performance in the present-day blast furnace. The coke must have sufficient strength, stability, hardness, and freedom from impurities to make it suitable. 2. If the coal in its raw form does not meet these requirements, it must be amenable to beneficiation or upgrading so that the requirements can be met. 3. It must be available in uniform quality and in sufficient quantities to meet the need. 4. Use of the coal must be economically attractive. If its quality is equivalent; to that of the coals with which it must compete, it must be no more expensive than they. If It is better, a premium price may perhaps be demanded. If, in any respect, it is the least bit less suitable, the cost must be lower to offset its disadvantages.

Jan 1, 1961

By Karl Ingmarsson

Larger mines spend millions of dollars annually on rock drilling tools, but often purchase based on historic consumption. The results vary from excess inventory to acute tools shortages. These lead to emergency sourcing, sometimes mixing products that don’t perform optimally. Boart Longyear analyzed the usage pattern of 96 thousand drill bits at thirteen different underground mining contracts, showing very high variability. The monthly standard deviation on a product level was 42%, with the highest for development and low volume bits. A new rule of thumb is suggested to carry only one month of safety stock for high volume bits, but increase to three months for low volume bits. This balance will reduce the risk of outages with less inventory. The accuracy can be improved by considering the specific conditions at each mine and reclassifying individual bits for a different safety stock level. Root cause analysis and collaborative forecasting between mines and suppliers can lead to further optimization of availability and inventory levels.

Feb 1, 2024