Search Documents

By M. C. Manderson

While the United States has been the world's largest volume producer and marketer of phosphatic fertilizers for many years, it has recently suffered heavy losses for a variety of reasons. While improved economic performance is expected, it is still at least a year or two away. But when recovery does manifest itself, it will likely yield only mediocre profits, due in part to the fact that about 50 percent of output is export-dependent. Therefore, there appears to be limited likelihood that profits will be adequate to justify the further outlay of large amounts of capital for expansion.

Jan 1, 1986

By Peter D. Warwick

Recent investigations conducted by Federal, State, and industry organizations suggest that significant coalbed gas resources may exist in the Cretaceous and Paleocene-Eocene coal beds of the Gulf of Mexico Coastal Plain. Exploration efforts have focused on three areas which are in south Texas, north-central Louisiana, and south-central Mississippi (Figure 1). Coal-bed gas production is currently underway in south Texas and in north-central Louisiana. In Mississippi, several test wells have been drilled but no data are available on their production potential.

Jan 1, 2005

By D. Piper, J. Noble, M. Richardson, J. Wojcik, L. W. Cope

L. Cope Welcome. I am pleased to see so many people interested enough to stay until this last session of the last afternoon of the convention. Of the people on the panel here, everyone has done everything in placer mining, but we have tried to sectionalize it with each one of us taking a particular portion. Any one of us could probably answer any question. I am very pleased to see some well experienced people in the audience. To start the discussion, Joe, can you give us a brief comparison of pit and drill sampling? J. Wojcik They both have their place. If you expect your deposit is something that is going to have widespread fairly uniform grades, then the pits may be the way to go. If you are going to have something you have to trace for several miles down the river valley, you can't do it with pits and do a proper sampling job. C. McLain Joe, the end result of all of this is to go ahead and mine it if it is a deposit. Do you try to relate your drilling results to something in mining itself against the recovery, because the drilling in different types of ground will give you different kinds of recoveries, and mining in the end is what you are going to do? Do you try to relate this to your mining method?

Jan 1, 1992

By J. E. Gebhardt, D. A. Rice, P. E. Richardson

An improved understanding of the significant role of electrochemical reactions in sulfide flotation has evolved in the past 20 years, This understanding has been accompanied by a corresponding increase in attempts to control the electrochemical potential of flotation pulps for monitoring and controlling sulfide flotation circuits to improve metallurgical performance. This paper discusses the basic electrochemistry of sulfide flotation and the use of electrochemical potential as a control parameter.

Jan 1, 1993

By G. D. Mainwaring, Weng L. W, Lam Y. K.

The first power transmission cable tunnel in Singapore was the 2.6km long undersea tunnel between Pulau Seraya and mainland Singapore, constructed in the1980s. Ten years later, similar concepts were used for the Tuas Cable Tunnel. The tunnel, which includes a 2.2km long immersed tube section, was designed to accommodate 10power circuits of 400kV and 230kV capacity. It is fully equipped with sophisticated control and communication equipment, fire suppressant and life safety systems plus a maintenance vehicle which runs on tracks through the length of the tunnel. The paper discusses the planning, design, and construction of the Tuas tunnel, and the development of these concepts for future tunnels.

Jan 1, 2001

Sweden is beginning to reap the rewards of a process that has transformed a country with a history of metal mining into one of Europe's most vibrant exploration regions. Exploration and mining companies from North America, Europe and Australia have joined local firms in the search of gold, base metals and diamonds. This has been due to changes in Sweden's mining laws in the early 1990s. These changes opened the way for unhindered private sector investment in the country's mineral industry. More than 20,000 km2 (4.9 million acres), mainly in northern Sweden, is now held under granted or applied exploration claims. Exploration permits diamonds, applied or granted covers more than half of Sweden's surface. This is a greater proportion of the country than ever before. Major mining companies and junior explorationists are evaluating a geological potential that bears favorable comparison to other major mining centers. Historically, Sweden's gold re- sources occur in greenstone belts in northernmost Sweden and in association with massive sulfide deposits in the Skellefte district. These are receiving particular attention by exploration companies. In addition, new areas in Sweden are also being explored for gold. This increases the probability that Swedish gold production - already the highest in Europe - will increase in the future (Table 1). Sweden's recorded mining history goes back for much of the last large pool of expertise in exploration, mining, equipment manufacturing and minerals industry research. In addition, the Geological Survey of Sweden provides sup- port for exploration in terms of data archives, processing and publications. Other benefits for exploration companies are Sweden's communications infrastructure, its member- ship in the European Union, bringing access to one of the world's major markets and the high level of educational, technical and language skills held by the country's work- force. And deregulation of the economy and the introduction of competitive corporate tax rates have made Sweden a favorable destination for investment in Europe.

Jan 1, 1997

By Chee Theng

"Keep calm and carry on mining. That has long been the conventional wisdom in the mining industry, a largely cyclical one that has weathered roller-coaster booms and busts. But in the years from 2002 to 2016, an unprecedented steep rise in commodities prices that lasted a decade and then took a sharp turn downward had made it hard for gold and silver miners to stay the course.“The last 15 years highlighted some of the structural and inherent challenges that our industry has, from product price uncertainty to long lead times to the capital intensity of our business,” said Mitchell Krebs, president and chief executive officer of Coeur Mining, who was the luncheon speaker at the American Exploration & Mining Association’s 122nd Annual Meeting held Dec. 5-9, 2016, in Reno, NV.Looking back, Krebs said, “We were given this enormous gift of a commodities super cycle, and the industry kind of blew the opportunity.” While gold prices rose 319 percent and silver prices rose more than 200 percent over the 2002 to 2016 period, the XAU index of 30 gold and silver mining companies’ stock prices went up by only 20 percent.Entering 2016, precious-metals prices have made a comeback, with gold rallying strongly from a six-year low at the start of the year. This time, the industry is ready. Companies are leaner and meaner, with lower costs, reduced debt and an increased focus on higher grades and quality ounces. Although opportunities were missed in the past, the industry has got its act together and is now well positioned to take advantage of a price upswing and even to show profits when prices fall, as they did in August 2016, pushed down by a strong dollar."

Feb 1, 2017

By W. K. Utt, C. C. Woodward, W. L. Howie, G. G. Miller

The process of roof drilling and bolting is one of the most dangerous jobs in underground mining. In the United States, roof drilling and bolting results in about 1,000 accidents with injuries each year. Researchers, from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are studying the feasibility of using a drill-monitoring system to estimate the strength of successive layers of rock and assess the integrity of a mine roof. Such a system would allow roof drill operators to be warned when a weak layer is being drilled. Using measurements taken during drilling, a neural network can classify mine roof strata in terms of relative strength. The concept has been proven in principle. This research project was undertaken to increase the safety of underground miners, especially those involved in roof bolting. The system should be applicable to the mobile drills now used in underground mines, and the system would likely find wider application as well.

Jan 1, 2003

By K. G. Colman

Este texto intenta facilitar al operador y contratista 10s datos básicos para dimensionar las cribas vibrantes que deban ser utilizadas en las plantas de trituración. Las capacidades básicas, factores que la modifican .... etc., utilizados en el cálculo de la superficie requerida, se han desarrollado empíricamente y modificados sus valores hasta el presente con 10s datos de las aplicaciones prácticas Hay que señalar que el cribado tiene mucho más de arte que de ciencia exacta; sin em- bargo, la información aquí presentada proporciona una razonable seguridad cuando se aplica al cálculo de cribado de minerales metálicos.

Jan 1, 1982

By S. P. Mehrotra, P. C. Kapur

A phase-species classification is suggested for the mathematical models of flotation kinetics. Important models are discussed and the structure of their rate constants and parameters is analyzed. Split or enhancement factors are formulated for different kinetic models. The steady state dynamics of the flotation circuits can always be described in terms of these factors. For simulation of circuits, feed is characterized in a formal manner starting from a multivariate distribution of particles in flotation rate, size and mineral content. Synthesis of optimum circuits which simultaneously searches for the best process variables and structural parameters from a generalized master network is described. Trends in the areas of search algorithms, role of middlings and feed identification etc. are indicated.

Jan 1, 1989

By M. Ericsson

The extractive industries consist of five major sectors: - Mining equipment and services - Dimensional stone - Industrial minerals - Aggregates - Metal mining These industries produce some finished goods but mostly semi-finished products as they feed into other industrial sectors: Basic metals, fabricated metals, construction, chemicals, dyes and pigments, inorganic chemicals, fertilizers, rubber and plastics and non-metallic mineral products. These are the major down-stream industries in this study. Taken together with the extractive industries they form the mineral resource based cluster. The mineral resource based cluster is a substantial part of the Finnish economy: It employs 211 000 persons, 39% of the number of employees in industry. The cluster?s exports account for 20% of industry exports. Value added is 34% of total value added in industry. Investments reach 35% of total industry investments.

Jan 1, 2003

By Wang Zuoyu

The manuscript of this paper was not available for publication when the Proceedings went to press. Should the author elect, he may distribute copies to the time of the Symposium.

Jan 1, 1986

By V. Srajer

The loading and hauling equipment simulation model was developed to satisfy, the requirements and need of the mining industry in western Canada. It is expected the model will be used to determine the' impact of various combina¬tion of loading and hauling equipment, company policies and maintenance procedures, haulage requirement, to evaluate possibilities, of the use of truck monitoring and dispatch systems, and to access loading and hauling equipment productivities. To evaluate the model, and to access its capabilities in addressing the above requirements, the model was validated. The validation was based on the following: 1. Running the model in-house to evaluate its structure, 2. Running the "test case" by timing models developed elsewhere to compare the results of simulation, 3. Soliciting of model critique from outside agencies, and 4. Comparison of calculated data with real time study data. The presented paper provide overview of the validation processes and summarize" results obtained during comparison and evaluation studies.

Jan 1, 1989

By E. B. Thorn

The production of portland cement requires that four basic elements -- calcium, silica, alumina and iron -- be ground to a fine powder, homogenized, and fed to the pyroprocessing unit, where it is burned to a cement clinker. The raw material must either be ground wet in a slurry form or dried and ground to a dry powder, with a fineness of approximately 85% passing the 200 M screen. According to the Portland Association's Plant Information Summary, approximately 38% of the U.S. capacity is ground wet and 62% ground dry. The following data is taken from the Portland Cement Association's 1981 Energy Survey: [Million BTU/Ton kW h/Ton Wet Process Plants 5.86 138 Long Dry Process Plants 4.97 123 Dry Preheater Plants 4.03 157 ]

Jan 1, 1984

By Hugh E. Cronin, Lok Home

THE PENETRATION RATE BASELINE DILEMMA The penetration rate is the instantaneous advance rate of a TBM in a rock tunnel. Normally expressed in feet per hour. The production rate is the penetration rate multiplied by the number of hours worked and then factored by the actual utilization of the TBM. In a given rock formation, the actual production rate is a result of many factors some of which are within the control of the contractor and some of which are based on the route selected. Factors that are within the contractors control are cutter profile, frequency of cutter changes, thrust, rotation speed, cutter spacing and the efficiency of the operation. Factors that are site (route) specific are compressive strength, fracture orientation, fracture frequency, micro- fracturing, quartz content, Moh’s hardness, Cerchar Abrasivity Brazilian Tensile Strength and Youngs Modulus of the rock. In addition the following route speci?c conditions are beyond the contractors control; rockjointing, rock stress fault zones, water in?ow and rock decomposition; all of which effect production rate. Any one of the above defined rock properties, equipment specifications and actual operating usage will change the penetration rate. Furthermore, since the rock formation changes both in content and orientation as the tunnel advances, the penetration rate is constantly varying. The current industry practice in bidding tunnels is for each contractor to individually evaluate the rock hardness and other properties and from this information develop a penetration rate. All other factors being equal, the contractor using the most optimistic penetration rate will be the low bidder and be awarded the project. As this view is by definition optimistic, invariably the rock will be harder than the low bid assessment and the contractor will request additional compensation for the changed condition. The contractor will attempt to justify his optimistic assessment as reasonable by using expert supporting analysis. The above described example which is quite common at present in the industry tends to make the most optimistic contractor (at time of bidding) the contractor selected for the project whereas it is in the owners interest to contract with the most efficient contractor not the most optimistic. This situation is similar to the Geotechnical analysis that was prevalent in the industry over twenty years ago. Many projects have experienced a significant reduction of penetration rate from that which was originally estimated. In these cases the contractor often makes a claim for extra compensation based on the difference between the actual rock encountered

Jan 1, 2003

Careful financial analysis of capital investments has always been a vital task in mining which is one of the most capital intensive sectors of the economy. Furthermore, mining costs have leapt ahead at an astonishing rate in recent years not just due to accelerated inflation, which affects everyone, but also due to the imposition of enormous costs of enviromental regulation and the continuing decline in ore tenor. Not only have unit costs risen, but the amount of effort expended to recover a pound of metal has increased due to the inexorable decrease in ore grades. New low-margin, high-volume mining investments place increasing importance on sound financial planning. Owing to the enormous investments involved, a greater share of individual corporate resources is committed to these projects than is normally the case in other industries. Thus, the consequences of failure are extremely grave, and a close examination of all inputs to the evaluation equation is clearly indicated.

Jan 1, 1979

By Ishwar G. Mulani

In conveyor design, the first step is capacity and the second step is belt width and speed. The third step is decision on 'ff," where distinction arises between DIN/ISO and CEMA for calculating resistances. Then again, both the methods are virtually similar. This topic helps in understanding Dm design style and its comparison to CEMA. This topic is from the book Engineering Science and Application Design for Belt Conveyor wherein the issue has been analysed in detail. It presents a workable calculation model to calculate the value off in design office, based on conveyor parameters. CEMA uses Kx, Ky and 0.01 5 instead off. Thus, f is a sum effect of Kx, Ky and 0.015. Hence, knowledge on f is also applicable to Kx and Ky. This helps to understand their relationship.

Jan 1, 2004

By Stephen B. Doppler

INTRODUCTION Following the world stock market debacle in October 1987, it would have been foolhardy to expect that securing equity funding in 1988 would be easy. Indeed, major equity financing's for gold mining companies have until recently been few and far between in the weeks and months following Black Monday. As a result, gold bullion loans have taken on an increasingly important role among producing firms in the industry. During 1988, the role of bullion loans has become increasingly complex and controversial. Some observers herald the emergence of a new breed of bullion loans - such as the 1,000,000 ounce loan to Newmont Mining, and the 400,000+ ounce facilities drawn down by Bond International Gold and Placer Pacific - as both increasing the public's awareness of the technique, and representing the dawn of a new age of gold financing. But are these recent loan facilities significantly different than those issued worldwide during the early to mid 19801s? Similarly, observers have voiced concerns regarding the role that gold loans play in the world's bullion markets, specifically in relation to their impact on prices. Have the new generation of mega-loans depressed current and future prices? Has the current surge of bullion loans irrevocably changed the nature of the gold market? Is there an upper limit on the number and size of gold loans?

Jan 1, 1988

By Debra W. Struhsacker, Jean Kiel, Jeffrey Thatcher

3.1 INTRODUCTION As heap leach precious metal projects become increasingly common in the United States, federal, state and local regulatory agencies are beginning to take a closer look at the short- and long-term environmental consequences of this recovery technology. From an operator's point of view, there is seemingly a confusing regulatory maze to be navigated and a plethora of permits and approvals to be obtained prior to commissioning a heap leach operation. The degree of difficulty associated with obtaining permits for a heap leach project depends largely upon the state in which the project is located. Permit acquisition is generally easiest in those states most familiar with heap leaching technology. For example, heap leaching is well understood in Nevada, and heap leach operations are relatively easy to permit, although permitting conditions in Nevada have recently become more stringent. However, many states are just beginning to become familiar with heap leach operations. Many of these states such as Idaho, Colorado, South Dakota, Oregon, Montana, Washington and South Carolina are in the process of drafting regulations and establishing guidelines for heap leach projects. In most cases, these regulations specify design and operating criteria as well as reclamation and decommissioning procedures. This chapter provides an overview of the regulatory and permitting aspects of heap leach operations. Permitting requirements for projects developed on federal land are discussed in detail. 'The state and local regulatory atmosphere and permitting requirements for various states are also presented. The chapter concludes with a generic permitting strategy. 3.2 KEY ENVIRONMENTAL CONCERNS The primary concern of most local, state, and federal regulatory agencies is the use, storage and transport of sodium cyanide (NaCn), and potential cyanide contamination of surface and groundwater resources. The toxicity of cyanide to people, fish and wildlife is also an important issue. Unfortunately, in the public eye, cyanide heap leaching has some emotional impacts similar to those associated with radioactivity and uranium mining. This perception and the general lack of understanding of cyanide can lead to unnecessary concern about cyanide contamination, further complicating the regulatory environment.

Jan 1, 1988

By John D. Abbatt, H. B. Newcombe

The Eldorado Epidemiology Project formally began in late 1978. It consists of a retrospective cohort study, to be followed by and to leave in place the mechanism for a prospective cohort monitoring program. These present and future activities are intended to merge into one another. The current study includes all Eldorado employees past and present for whom records are available. The objectives of the undertaking are - 1) to obtain cause-and-effect, dose-response data with which to evaluate the risks to workers in radon and radon daughter containing atmospheres, and to provide additional quantitative information on which to base possible improvements in working conditions; 2) to identify any dead employees of E.N.L. whose cause of death suggests that a potential compensation claim right exists for their survivors, and to similarly identify living ex-employees of E.N.L. whose work histories and states of health suggest potential compensation claim rights. The nature of the study has been determined by the history of Eldorado, which will be described briefly. Eldorado began (as Eldorado Gold Mines) in the late 1920's, operating relatively unsuccessfully in Manitoba. In 1930-31 the emphasis shifted from gold to uranium, and what became the Port Radium mine was first staked. From the very early 1930's until 1942 the company's purpose was almost entirely devoted to the mining of pitchblende - uranium ore - from the Port Radium site, and the extraction of radium from this ore at the Port Hope refinery in Ontario, a process from which the uranium was a largely stockpiled byproduct. In 1942 the company was requested by the Canadian government to accelerate the production of ore, and of uranium. At the same time, all its stockpile of uranium (then being stored in silos as a "waste" product which might later "come in") was acquired for the Manhattan Project. In 1944 the company shares were bought by the Canadian government and the company itself became Eldorado Mining and Refining (1944) Limited; it has operated as a Crown corporation ever since. The name was changed to Eldorado Nuclear Limited in 1968. The Port Radium mine was closed in 1960, and since 1953 the Beaverlodge uranium mine complex has operated on the northern shores of Lake Athabasca. Radium production was discontinued in 1954 when the radium circuit was taken out of the refinery, and since that time the refinery's products have been various types of refined uranium (uranium dioxide, uranium trioxide and uranium hexafluoride) plus metallic uranium. The refinery, of course, processes the company's own yellowcake but as it is one of only five refineries in the western world, most of its work consists of custom refining for a large variety of customers. In addition to the mining and the refining operations, there have been three other divisions involved, and these are, respectively, Aviation, R. & D., and Exploration, in addition to the financial, corporate, administrative and support activities. MATERIAL AND METHODS The human study population (Abbatt, J.D. et al., 1980) consists of all Eldorado employees who have ever worked for E.N.L. and for whom records are available. The total nominal roll to December 31, 1980 is approximately 21,000 and consists of employees of the Mining, Refining, R. & D., Aviation and Exploration Divisions, as well as a relatively small number of other employees (Head Office, etc.). The basic epidemiologic design, as has been mentioned, is for a retrospective cohort study merging into a prospective cohort study, and depending very heavily upon automated record linkage and file matching. The original design called for an initial assembly of the bulk of the nominal roll, prior to the first of two matches with the National Mortality File. The first of these two matches is now complete and the second is to be separated from it in time by 18 months to two years. The second match will be the definitive match prior to the analysis, the interpretation of the data, and the publication of the results. The period between the two matches was designed to permit completion of the nominal roll, including: - addition of previously missing individuals and groups, elimination of duplicates, and amplification of identifying information, - assembly of work histories and exposure information for each individual, - digestion and application of lessons and modifications resulting from the first match with the National Mortality File at Statistics Canada, - preparation of files for the definitive second match. The analysis of data will be carried out by the National Cancer Institute of Canada Epidemiology Unit based at the University of Toronto. This group, with whom Eldorado Nuclear has a memorandum of understanding, have for a variety of reasons, including their familiarity with record linkage and their expertise, been members of the Project Team since

Jan 1, 1981