Search Documents

By R. Debkowski

The current underground infrastructure of an old monumental salt mine along with using it as a tourist, museum, nature, resort, conference and cultural events place is presented in the paper. At present, mainly in the monumental part of mine, only a small part of the historical chambers, which together with galleries form a tourist route available to visitors. Moreover, the essential activities aimed to make the tourist route more attractive and to change the decor of the underground sites are discussed.

Jan 1, 2006

By C. Douglas Lee

This case study describes the work done at the University of Arizona on the development of a computer mine model for an irregularly shaped and spotty ore deposit. The purpose of the work was to develop techniques for modeling any highly irregular deposit, for which the regular 3D fixed block model is not well suited. The deposit contained complex geology consisting of sedimentary beds that had been faulted, thrusted, and intruded by igneous rocks (see Fig. 1). The physical dimensions of the modeled ore body were 1067 m (3500 ft) along the N-S direction and 914 m (3000 ft) along the E-W direction. Topographic relief in the modeled area was approximately 274 m (900 ft). The highest grade of ore was found near the surface with mineralization extending down to approximately 152 m (500 ft) below. Using a fixed bench height of 12 m (40 ft), the model required 25 levels with the highest elevation being at 1286 m (4220 ft). Fig. 2 shows a cross section of the developed computer model of the ore deposit. The particular modeling approach selected for this deposit was the 3D irregular block model.* This meant that only the dimension of bench height was fixed at 12 m (40 ft). Irregular size blocks in the form of polygons were adopted in the model to describe the ore zones and geologic contacts. The following sections of this chapter describe some of the techniques used in modeling.

Jan 1, 1979

By Carl S. Vender

Knife River Coal Mining Co.'s Beulah Mine is a multiple-seam lignite operation located in western North Dakota. The mine began production in 1963 with annual production of 450 kt (496,000 st). It now produces 2.2 Mt/a (2.4 million stpy). As development progresses, operations advanced into more complex geologic areas. Various techniques have been analyzed to maximize coal recovery in a cost-effective manner. Additional studies are ongoing to determine what changes will be implemented as deep, wet sands are encountered in the reserve area. Knife River Coal began as an underground operation in 1924 at Beulah, 120 km (75 miles) northwest of Bismarck. In 1950, the operation converted to a combination underground and surface mine. The underground segment was closed in 1952. Development of the existing reserve area south of Beulah began in 1963. About one-fourth of the acreage under permit (Fig. 1) is sufficient for 10 years at current production rates.

Jan 1, 1991

By J. Kretschmann, P. Goerke-Mallet, C. Melchers

Mining always leaves a mark behind. Dealing with this legacy is not only a tremendous challenge in Germany, but internationally too. The Technical University Georg Agricola (THGA) in Bochum, Germany, has established a Research Center for Post-Mining. Researchers combine expertise from a variety of technical and nontechnical fields in their quest to shape the post-mining era that completes the mine life cycle. In this respect, the Research Center focuses on four research areas: Perpetual tasks and mine water management, Geomonitoring, Material sciences and site transition. With more than 200 years of successful partnership with the mining industry in Germany and abroad, THGA offers a perfect setting for fresh and sound ideas in order support mining’s social license to operate. The aim of the paper is to describe the Post-Mining Research Center along with exemplary research projects that are of interest to the mining industry globally and to foster technical communication and research networking.

Mar 2, 2022

By D. Baker

Alternative material handling methods are allowing material handling operations to be performed with increased cost savings. This allows for higher production levels with better returns. RAHCO International Inc.'s Continuous Mining Excavator (CME) has recently received a lot of attention due in part to its operating efficiency, flexibility, and associated low operating costs. The CME is designed to perform three primary functions. These include material excavation, sizing and loading operations. In many applications, a drilling and blasting process can be eliminated. The CME was developed originally in 1985 for open pit coal mining. See figure I. Since this time, it has been proven an effective system for excavating many other types of materials including friable and sticky materials. It has also been shown to suitably handle hard rock in certain site conditions.

Jan 1, 1998

By J. A. Brierley, S. N. McIntosh, C. L. Brierley, E. G. Baglin, E. G. Noble, D. L. Lampshire

The U.S. Bureau of Mines investigated column bioleaching as a means of recovering manganese from a domestic low-grade oxide ore. Manganese was solubilized from the ore using indigenous heterotrophic microorganisms and molasses as the nutrient source. The effects of medium flow rate, molasses concentration, and frequency of medium replacement on the rate of manganese extraction were examined. Results showed that flow rates between 0.4 and 8.1 L/min/m2 had little impact on manganese extraction, while an increase in the total amount of molasses applied during leaching directly affected the extent and rate of manganese extraction. Manganese extractions of more than 90% were achieved in 12 weeks of bioleaching in column tests using 500 g charges of ore. Sugar utilization by the microorganisms and formation of organic acid metabolites were monitored by high performance liquid chromatography (HPLC). Two methods were evaluated to recover manganese from the sugar- depleted bioleaching medium: (1) adsorption onto weak cation exchange resin, followed by stripping and precipitation techniques; and (2) direct precipitation of the manganese as MnCO, using ammonium carbonate. Both recovery methods removed at least 95% of the solubilized manganese from the medium as a carbonate salt. The stripped molasses medium was replenished with fresh molasses and recycled back through the bioleach column, successfully leaching more manganese.

Jan 1, 1993

By Clinton Strachan, Dirk J. A. van Zyl

11.1 INTRODUCTION This chapter outlines some of the selection and design considerations for leach pads and liners. Leach pads and liners are generally chosen to provide the required or desired levels of low permeability and foundation conditions at minimum cost. The selection and design of a particular liner depends upon its anticipated use and performance, and what materials may be available. A leach pad is the firm base for a heap. When geomembrane liners are used, the pad is the firm, compacted foundation upon which the liner is placed. In the case of a clay liner, the clay liner is usually also the pad. It is important to consider the design of a pad or liner in terms of a system. The "leach pad system" consists of the prepared foundation, bedding layer (if used), liner (s), seepage collection or detection layer (if used), and cover layer. Foundation preparation is necessary to ensure a stable base for the rest of the leach pad system. A bedding layer is used to protect a liner from being punctured by large angular fragments in the foundation material. A seepage collection or detection layer, consisting of well-drained material and (sometimes) pipes draining to a collection sump, is included when a double liner is used. A cover layer on top of the liner can serve the following purposes (van Zyl and Strachan, 1986): • Preventing of ultraviolet light exposure to sensitive geomembranes; • Limiting evaporation from compacted clay liners and thereby eliminating cracking of such liners; • More efficient collecting of leachate; and • Protecting the liner from damage during heap construction. Economic evaluations of alternative liners for a project must include the overall system. For example, a geomembrane liner may require different foundation preparation and cover material selection and placement than a clay liner. Liners can be made of compacted clay onsite, amended soil, or geomembranes. Geomembrane is a generic term that has been proposed to replace many terms, including synthetic membranes, polymeric membranes, plastic

Jan 1, 1988

By N. I. Jayaraman

Dust scrubbers on continuous miners are steadily gaining in popularity. Recent US Bureau of Mines research on scrubbers is reviewed, with emphasis on development of a new type of water-powered scrubber that can he retrofitted to existing miners; comparison of scrubber effectiveness with blowing and exhaust line ventilation; and improving the quartz dust collection of flooded-bed panels.

Jan 1, 1990

By Paul F. Saxton

Introduction As the world economies continue to face an increased demand for natural resources to support growth in the established and developing world, the western mining industry has expanded its operations and funding of mineral developments into new and relatively unexplored regions of the world. Mining companies worldwide, in order to grow in a global economy, are now actively exploring and developing mineral resources in the emerging markets of South and Central America and most recently have expanded activities throughout Asia. South East Asia Resources (S.E.A. Resources) has recognized the vast resource potential offered by countries such as China, India and Indonesia, Asia's main driving forces of economic growth and has made a commitment to be actively involved in the area. These countries rich in mineral resources, represent some of the highly prospective and underexplored regions on earth. Their vast potential has been underestimated because of political reasons and overlooked as Central and South America still continue to be the focus of exploration for many mining companies. Most of these Asian countries have faced a prolonged period of political unrest and it has not been until recently that they have begun to enjoy a relatively stable political climate which has encouraged foreign investment, growth and economic development. These countries are in need of capital to develop their infrastructure and market economies. Their wealth in resources is one of the best methods to achieve their goals. Gold is usually one of the first targets to be extracted from developing economies. Equivalent-sized gold projects tend to cost less to develop and require less supporting infrastructure than base metals. These projects are easier to finance and, most important of all, tend to give a quicker return on investment than that offered by base metals. They also provide the economy with precious foreign exchange, international investment and the technology required to build the country. Following is a graph representing the global re-allocation of the total capital investment on the twenty largest gold projects now under construction with the total for those under construction in 1990.

Jan 1, 1996

By K. Lang

The use of high-efficiency electrical submersible pumps (ESPs) for large scale, open pit mine dewatering operations provides a good example of how technology, products and services from the oil and gas industry can be adapted to the mining industry. In this case, the mine is Goldcorp?s Peñasquito in the Zacatecas state of Mexico, at the Peñasco and Chile Colorado open pit deposits. The technology, products and services are from Schlumberger artificial lift (AL) and Schlumberger industrial water services (IWS). Overview of high-efficiency ESPs This section provides a brief description of the basic components, specifications and operating capacity ranges for the ESPs compared with traditional or conventional dewatering well pumps. This information helps to establish how ESPs provide certain functional and economic advantages over conventional pumps in a mine dewatering application. A schematic of a high-efficiency ESP in an oil and gas (O&G) application is shown in Fig. 1.

Sep 1, 2013

By Kadri Dagdelen, M. Waqar Asad

Cement production involves the processing of raw materials that contain - Si02, A1203, Fe203, CaO, MgO, LOI (loss of ignition), S03, K20, Na2O, Ti02, P2055 and Cl- to produce the synthetic mineral mixture called "clinker". The use of other additives - sandstone, flyash, iron ore, and clay - is also mandatory in order to achieve the optimum blending requirements of cement. However, the use of these additives needs to be minimized due to their significantly higher costs ($/Ton). This paper presents a mixed integer programming (MIP)-based optimum quarry scheduling algorithm, which is used to generate quarry plans, satisfying geometric and production capacity constraints while providing minimum cost/optimum blend of raw materials mix to a cement plant. The benefits of this new methodology are demonstrated on a case study.

Jan 1, 2002

The long-term goal of the Collaborative Research Centre 525 is the identification of options for the resource-sensitive supply and utilization of metallic raw materials. In order to address these issues, an integrated resource management system for metallic raw materials was developed and tested. Simulations were carried out, using the tools and methodical approaches developed in this system, in order to compare alternative operating scenarios for aluminium and copper. However, before these alternative operating scenarios could be formulated and assessed, it was necessary to develop a consistent set of indicators to monitor progress towards sustainable development in the processing and utilization of metallic raw materials. The primary objective of the centre is to develop a set of indicators, which adopt a holistic approach to resource management, thereby enabling the assessment of different operating scenarios within the broadest possible context. The target audience for this research consists of decision-makers in the realms of politics, business and industry, as well as NGO?s.

Jan 1, 2003

Improvements in cost efficiency, noise control, environmental design and ergonomics ? the mining and construction industries are facing demands on many fronts. The international manufacturers of construction machinery are responding to these challenges, and they will be presenting their innovations in all these fields at bauma 2013. bauma, the international trade fair for mining and construction machinery, mining vehicles, and building material machines, takes place from April 15 to 21, 2013 at the Messe Munchen exhibition center in Munich, Germany. The last bauma, in 2010, attracted 3,256 exhibitors from 53 countries, and more than 420,000 visitors from more than 200 nations. Covering a total of 555,000 m2 (5.97 million sq ft) of exhibition space, bauma is one of the largest trade shows in the world. This year?s fair is expected to surpass the 2010 figures. Here are some examples of the new developments visitors can expect to see at the show.

Jan 1, 2013

By Jeroen van Eldert, Daniel Johansson, Henrik Ittner, Håkan Schunnesson

"Numerous aspects of underground construction, from structural stability to construction costs, depended on the tunnel quality, including blast damage and the Excavation Damage Zone. Accurately quantifying the extent and severity of damaged rock is a problem. Recent technical developments in the field of Measurement While Drilling (MWD), including software for on-board logging and on-site analysis, have shown potential for rock-mass characterization. Ground Penetrating Radar (GPR) and P-wave velocity measurement have also improved and show similar potential. This paper explores the use of MWD, GPR and P-wave velocity measurements and uses them in techniques for excavation damage characterization and prediction. The paper is based on data collected from a small underground waste-collection site in central Stockholm, Sweden. The data is correlated against rock-mass characteristics and their responses are evaluated. Results indicate potential for excavation damage characterization for all tested techniques, which could minimize blasting damage and improve the over-all tunnel quality. 1 INTRODUCTION During underground excavation the rock mass is influenced in many ways. The Excavation Damage Zone (EDZ) is a result of these influences. The EDZ can be defined by an irreversible change in rock mass properties, for example increased permeability. EDZ is influenced by the excavation method, the rock mass properties and the in-situ stresses in the area of the tunneling. Since the 1990s research has been done on the EDZ by Emsley et al. (1997), Christiansson et al. (2005), Olsson et al. (2009), Ouchterlony et al. (2009), Ittner et al. (2014), and Siren et al. (2015). Based on past literature the EDZ have in this paper been separated in the following subzones: 1. Failure Zone or over-break is the area outside the planned tunnel profile, including the Look-Out and hole deviation. This zone consists of fracture networks (both natural and blasting-induced), that caused rock fall-outs. The extent of the over-break can be determined by volumetric scanning and photogrammetry and the half cast factor can be used as a damage indicator. 2. The Damaged Zone is split into three parts and but the quantity and depth of damage is difficult to measure. Although it can be visualized by sawing of rock slices in the tunnel wall (Olsson et al. 2009), diamond coring (DC) or P-wave velocity reduction (Jern 2001): a. Inner Damage Zone (Crush Zone): It is located directly around the drill hole, and is caused by the shock-wave energy of the detonation. The micro fractures in the Crush Zone produce a white-wash (rock dust) in the half cast. b. Transition Zone: This zone consists of micro fractures that connect and form macro fractures, both radially and parallel to the tunnel wall. The macro fractures are caused by the gas expansion during the detonation of the explosive; it increases the pressure in the (micro) fractures and creates the macro fractures. Seismic reflection, rock slicing and core drilling can be used for the examination. c. Progressing Zone: In this zone the existing radial fractures propagate due to the increase gas pressure inside these macro fractures. Examination methods are seismic reflection, rock slicing and core drilling. In addition, the Peak Particle Velocity (vibrations) could be used to estimate the depth (Tesarik et al. 2011)."

Jan 1, 2016

By X. Wen, D. Tao, B. Li

A high effective method using a hammer mill, a column pneumatic separator and an electrostatic separator was studied for recycling copper from waste printed circuit board. The factors influencing the copper liberation degree and following separations were discussed. Two different physical separating methods were compared and discussed. Experiment results show that a well-controlled impact action can produce a satisfactory degree of copper liberation at a relatively coarse particle size. Around 90% copper recovery from printed circuit board for coarse particle size can be achieved by using a combination of electrostatic separation and pneumatic separation.

Jan 1, 2003

By J. T. Ryan, Griffin. Wayne H.

This paper shows that if a drift has a brattice which is sufficiently leaky, changes in the operating point of the fan depend solely on the volumetric efficiency within the drift. Under this high leakage condition, an increase in the length of the drift causes very little shift in the fan operating point. For less leaky brattices, the operating point depends on both the fan characteristic curve and the volumetric efficiency. It is shown that for the fan curve and drift parameters used in this paper the fan operating point in a drift with a volumetric efficiency of 50% is essentially the same as a drift which has a zero efficiency. In this region of efficiency, an increase of 300% in the length of the drift causes only a 3% increase in fan operating pressure.

Jan 1, 1993

"Above ground, elevated belt conveyors that span more than 200 m (656 ft) between support points can cross valleys, rivers, forests and buildings with a minimal footprint. The cable bridge conveyor (CBC) is a new type of suspension bridge based belt conveyor system that has long spans between support points. It combines a typical belt conveyor and an improved simple suspension bridge to form a conveyor bridge. The improved simple suspension bridge places a widened bridge deck directly on suspended cables, without the need for high truss towers. The benefits include reduced cost and increase aerodynamic stability compared to conventional suspension bridges. The CBC’s compatibility with current belt conveyors allows versatility in application.A belt conveyor is a ubiquitous material handling system. Conveyors can be placed directly on ground or elevated above ground by support structures. Considerations of cost, design, environment, civil work, safety and process requirements are all factors in choosing the ground-based or elevated conveyors (Zhang, 2014). The ground-based conveyor has the lowest structural cost when the conveyor is placed on an existing road. Maintenance access is easy and straightforward. Compared to the groundbased conveyor, the elevated conveyor can cross existing buildings and structures, give passage to traffic beneath the conveyor, has a smaller footprint and requires less civil work to pass mountainous areas. The drawback of the elevated conveyor is higher structural cost, which can be compared with savings in civil work and other benefits. Conventional elevated conveyors are supported by rigid truss-type structures, with a typical span of 15 to 25 m (50 to 82 ft) between concrete support bents or steel trestles. Triangular truss, using steel pipes instead of hot rolled steel sections, is more efficient. The typical span of a triangular truss-supported conveyor is around 30 to 40 m (100 to 130 ft), while the weight is about 10 percent less than conventional box truss with a shorter span (Jennings, 2013).Long-span elevated structures based on suspension bridge is another step forward in increasing the distance between support bents, reaching 100 to 400 m (330 to 1,312 ft) and beyond. The wide distance between the support points of an elevated conveyor offers unique benefits. The conveyor can cross rivers, valleys, highways, forests and other obstacles with minimal footprint and reduced civil work. The versatility from long-span conveyors makes bulk material transportation over previously impossible terrains now a feasible option."

Jan 1, 2014

"Above ground, elevated belt conveyors with span >200m between support points can cross valleys, rivers, forests and buildings with minimal footprint. The Cable Bridge Conveyor is a new type of suspension bridge based belt conveyor system that has long span between support points. It combines typical belt conveyor and the improved simple suspension bridge to form a conveyor bridge. The improved simple suspension bridge places a widened bridge deck directly on suspended cables, without the need for high truss towers. The benefits include reduced cost and increase aerodynamic stability compared to conventional suspension bridges. The Cable Bridge Conveyor’s compatibility with current belt conveyors allows the versatility in application. INTRODUCTION Belt conveyor is a ubiquitous material handling system. Conveyors can be placed directly on ground or elevated above ground by support structures. Considerations of cost, design, environment, civil work, safety and process requirements are all factors in choosing the ground based or elevated conveyors (1). The ground based conveyor has the lowest structural cost, where the conveyor is laying on an existing road. Maintenance access is easy and straight forward. Compared to the ground based conveyor, the elevated conveyor can cross existing buildings and structures, give passage to traffic beneath the conveyor, has smaller footprint, and requires less civil work to pass mountainous areas. The drawback of the elevated conveyor is higher structural cost, which can be compared with savings in civil work and other benefits. Conventional elevated conveyors are supported by rigid truss type structures, with typical span of 15m to 25m between concrete support bents or steel trestles. Triangular truss, using steel pipes instead of hot rolled steel sections, is more efficient. The typical span of triangular truss supported conveyor is around 30m to 40m, while the weight is about 10% less than conventional box truss with shorter span (2). Long span elevated structure based on suspension bridge is another step forward in increasing the distance between support bents, reaching 100m~400m and beyond. The very wide distance between support points of an elevated conveyor offers unique benefits. The conveyor can cross rivers, valleys, highways, forests and other obstacles with minimal footprint and reduced civil work. The versatility from long span conveyors makes bulk material transportation over previously impossible terrains now a feasible option."

Jan 1, 2015

By L. M. Gochioco

The Seismic Interactive Interpretation Workstation (S//W) provides a wide spectrum of utilities ranging from improving field acquisition techniques, data processing and interpretation of coal seismic data. The power of the workstation lies in the interpretation process where various sets of geophysical and geological data are integrated to form a network of information that is stored in a database. Computer models are generated from known borehole and geologic information and later cross-correlated with the processed seismic data. Structural and stratigraphic modeling techniques add another dimension to the interpretation process. Complex trace attributes highlight subtle features not easily observed in black and white sections. Using the computer workstation, the explorationist gains valuable insight and conducts more intelligent interpretation of seismic data through a more comprehensive network of data analysis.

Jan 1, 1992

By Noel A. Genco, Edward F. McCarthy, Robert J. Piniazkiewicz

Talc, when it can be isolated as a pure mineral, has a composition of 63.36% SiO2, 31.89% MgO, and 4.75% H,O. However, as a commercial commodity less than half of all talc sold has a purity exceeding 95%. Nevertheless, impure talc products find a multitude of uses and few substitutes in many industrial applications. Minerals commonly associated with and sold together in talcose mixtures are chlorite, dolomite, mica, magnesite, and tremolite. Steatite was originally a mineralogical term applied to pure talc. Today steatite usually denotes a high-talc ceramic body used as an electrical insulator, and the talc used in such applications is known as steatitic talc. Steatitic talc generally is found in massive, high- purity form and in the past was machined directly into electrical parts, which rarely is done today. Impure varieties of massive or block talc are still commonly termed soapstone. Soft massive talc, suitable for crayon manufacture, has been referred to as French chalk. It has been common practice to discuss talc, soapstone, and pyrophyllite under the same general heading. In the case of soap- stone and talc this is natural, since many different types of platy, soft minerals exhibiting a high degree of lubricity (commonly referred to as slip) have been grouped together and called soapstone or talc. Further, there are mineralogical relationships between pyrophyllite and montmorillonite and between talc and hectorite. Thus, talc and pyrophyllite are sometimes referred to as clay minerals. When finely divided talc or pyrophyllite are combined with water in proportions to make a slurry, the end product does have the appearance of a clay-water mixture. Soapstone for utensils and ornaments was mined by prehistoric Native Americans on Santa Catalina Island, CA. In the mid- 1800s soapstone from deposits along the western foothills of the Sierra Nevada Mountains was used by white settlers as building and ornamental stone and for the linings and foundations of furnaces (Anon., 1956). Previous to 1916 the annual recorded production in California did not exceed 1.8 kt. From 1912 to 1918, however, output rose sharply when the Talc City, Western, and Silver Lake mines were put into operation. From 1916 to 1935, the state's annual output of talc was in the range of 8.2 to 18.2 kt. There was another increase in the mid-1930s, when the use of talc in wall tile grew rapidly. In California the production of talc grew to 57.2 kt in 1943. The post-war building boom helped California's production to grow to 108.9 kt in 1951. Production stood at 149.8 kt in 1968, 13 1.6 kt in 1969, 167.9 kt in 1970, and 140.7 kt in 1972. In the mid-seventies and early eighties, however, California's talc production declined to approximately 20 kt in 1992 due to reserves exhaustion and the material's tremolite content, which raised significant product liability concerns at the time. Talc mining in New York State dates from about 1878, when a Colonel Palmer and associates opened the first commercial talc mine on the Nelson Freeman farm near Talcville. In 1893 this operation was sold to International Pulp Co., which changed its name to International Talc Co. in 1944. The company was acquired by R.T. Vanderbilt Co., Inc., in 1974. A new talc operation, Gouverneur Talc Co., owned by R.T. Vanderbilt Co., began operations near Balmat, NY, in 1948. The initial capacity of the processing plant was 180 tpd (Gillingham, 1950). Subsequent expansions have increased capacity to more than 725 tpd. Talc was discovered in the area of Johnson, VT, in 1902, marking the birth of the Vermont talc industry. American Minerals Co. initiated plant operations at Johnson in 1904. MagnesiaTalc Co. opened a plant at Waterbury, VT, in 1913 (Burmeister, 1963, Trauffer, 1964) and acquired American Minerals Co. in 1923. The Waterbury mine had a long history as a producer of talc crayons. Eastern Magnesia Talc Co. was formed in 1924 by the merger of Eastern Talc Co. and Magnesia Talc Co. In 1956 Vermont Mineral Co., with a talc mine at Hammondsville, VT, was also acquired. A new plant was then built at Gassetts to produce roofing products. In order to produce high grade products for several markets, Eastern Magnesia Talc Co. began operating a modem froth flotation plant at West Windsor, VT, in 1964. The ore was provided by the Hammondsville mine. This operation, known as Windsor Minerals, Inc., continued from 1972 to 1989 as a subsidiary of Johnson and Johnson Co. In 1989 Cyprus Minerals Co. acquired Vermont Talc, Inc. and Windsor Minerals, Inc.. thus consolidating the talc mining and processing operations at Hamm, Windham, Johnson, Chester, Ludlow, West Windsor, Troy, and Reading, VT, under one ownership. As the result of Cyprus' sale of its worldwide talc assets to the RTZ Group in 1992, its US talc operations are now part of Luzenac America, Inc.

Jan 1, 1994