Search Documents

By Oluwafemi Salami

Conducting full-scale fire experiments in underground mines is difficult and expensive. Sometimes, it is impossible to carry out fire tests in mines due to the danger they pose to mine workers and the underground facilities. However, understanding the potential occurrence of fires in a mine and their dynamics is critical to developing an appropriate emergency evacuation plan, fire suppression, and firefighting techniques. In this study, a numerical fire model using computational fluid dynamics (CFD) with fire dynamics simulator (FDS) 6.7.6 was developed to examine the influence of tunnel bifurcation on maximum temperature beneath a tunnel ceiling. The model was validated using full-scale experimental data. The maximum ceiling gas temperature predicted using FDS and measured maximum smoke temperature during the experiment shows good agreement. The study shows that bifurcation could lower the maximum ceiling temperature of fire-induced smoke in a subsurface environment. The findings from this study apply to the broader field of ventilation and fire life safety in tunnels and other underground environments.

Jun 23, 2024

Considerable attention has been given to the restoration of low-level radioactive (<1000 pCl/g) sites contaminated during the early years of the atomic energy program. Current clean-up activities which involve the relocation of contaminated soils to licensed disposal sites have been shown to be very costly due to the large volumes of soils which must be excavated, transported and stored. Recent characterization studies conducted at Virginia Tech suggest that the volume of soil requiring disposal can be greatly reduced using mineral processing techniques such as classification, density separation and froth flotation. This article discusses the application of these technologies for soil remediation and describes a conceptual flowsheet for treating soil samples from two contaminated sites.

Jan 1, 1997

By Roshan B. Bhappu

Although the economic importance of recovering copper by leaching of mine work dumps from open-pit operations has been realized for some time, serious attempts to understand and to improve such operations through scientific research has been made only in recent years. This progress report covers the results of chemical, physical, and biological studies pertaining to the dump leaching process and discusses salient features and parameters that may be helpful in improving such operations.

Jan 1, 1968

By Elnaz Saminfar, Jae Bateman, Eric Westergren, Mark Trim

This paper presents a case study of two major Australian infrastructure projects that used digital engineering to facilitate design delivery: WestConnex Project (Rozelle Interchange), and Sydney Metro West (Eastern Tunnelling Package). The paper presents project overviews and building information modeling (BIM) execution and focuses on modeling techniques, software utilization, data management strategies and how the digital models helped the design-build team mitigate impacts to schedule by identifying clashes between disciplines before the execution of work. Finally, it demonstrates the positive and transformative impact of digital engineering on the design and construction of large underground infrastructure projects and highlights its role in asset management throughout the project lifecycle.

Jun 23, 2024

By M. I. Brittan

A technique has been developed that analyzes routine mill operating data to determine the key operating parameters responsible for gold losses to tails. These parameters represent the prime operating variables having a dominant effect on gold recovery. The technique quantifies these effects for the specific plant being analyzed, providing a tool to optimize recovery and costs and so enhance the mine?s cash flow. The quantitative relationships generated will be different for each ore and plant: every case is site-specific and has to be treated on its merits. Examples are provided to illustrate the considerable metallurgical and financial benefits which can be realized from optimization. The examples are taken from case studies of mills in four major gold mining districts of the world.

Jan 1, 2010

By G. B. J. Leon, M. Karmis, C. Newman

"The prediction of surface deformations due to underground mining operations has been a long recognized practice with case studies documented as far back as 1556 in Georgius Agricola's De Re Metallica (Latin for On the Nature of Minerals). There is currently increased public awareness and regulatory scrutiny on the potential impacts of underground longwall and second mining operations, but this time the focus is placed on environmental impacts to overlaying bodies of water such as streams, rivers, wetlands, lakes, etc. (Karmis and Agioutantis, 2015). Community residents and environmental groups, as well as federal and state regulatory agencies, have often cited adverse stream impacts and demanded stronger measures and scrutiny in issuing mining and reclamation permits (Booth, 2006). Mining companies are required to focus on the protection of sensitive bodies of water through the monitoring of stream flow and water quality, management and rehabilitation techniques, as well as the adoption of ""no mining zones,"" which potentially sterilize large portions of minable coal reserves. This paper examines the use of an empirical modeling approach for the protection of surface streams based on evaluation of ground strain magnitudes. Utilizing enhanced features of the Surface Deformation Prediction Software (SDPS), ground movements can be predicted accurately in the vicinity of surface bodies of water. The modeling of ground movements can aid in establishing optimum extraction sequences, while the magnitudes of anticipated subsidence can be used in the evaluation of mitigation plans when undermining surface bodies of water. INTRODUCTION When utilizing high recovery underground mining methods, such as longwall or room-and-pillar mining, the movement and deformation of the overburden propagates toward the surface and may affect the integrity of overlying surface streams (Peng et al, 1996). Published studies cite three major mechanisms of subsidence as most likely to impact streams: displacement, slope, and strain. While subsidence-induced vertical displacement cause little structural damage to the stream bed, it may create adverse drainage and stream flow issues as the subsidence trough allows for ponding (Dawkins, 2003). Subsidence initiated changes to the slope, or tilt, of a stream may have adverse effects on water flow. As the stream enters the subsidence trough, the gradient increases providing potential erosion control problems. When exiting the subsidence trough, a reduction of the gradient may inhibit stream flow, causing localized ponding (Peng, 2008). While vertical displacement and tilt both may have detrimental effects to surface streams, subsidence induced strains have been documented as being the most damaging to surface streams and structures causing distortion, fractures, or failure (Singh, 1992). When stream beds are subjected to high tensile strain, tensile cracks may form at the surface level allowing for the direct loss of stream flow through fissures. When stream beds are located in areas of high compressive strain, rock layers forming the stream bed can fail as the stream bed, ""ruptures,"" upward blocking stream flow or having the stream diverted into the facture zone at the base (Iannacchione, et. al., 2010)"

Jan 1, 2016

By E. L. Gillenwater

Coal mine planning has three distinct decision levels: (1) decisions made at the upper level of management that determine production requirements for specific mines, (2) decisions made at the middle management level, the mine level, that determine how the mine satisfies its production requirements, and (3) decisions made at the operating level of management, the sectional level, that determine the sequencing of machine movements at the face. In this paper, the underground production scheduling problem is formulated in multi-stages using the Hierarchical Production Planning (HPP) approach. Two linear programming HPP models for accomplishing decisions at the first two levels are developed. Both models address the aggregate production planning process. The Mine Production Scheduling (MPS) model permits determination of monthly production and inventory levels. The Section Production Scheduling (SPS) model incorporates a quality blending requirement into the determination of weekly sectional production and inventory levels.

Jan 1, 1995

"A carefully planned laboratory test program is the foundation for the successful development of a sulfide flotation process. In this paper, the development of a copper-molybdenum flotation process is described. However, the concepts discussed can be applied to most sulfide flotation systems and to many industrial minerals projects as well. Each step is examined, beginning with sample procurement and covering sample preparation, flotation test preparation grinding, scoping flotation tests for reagent scheme selection, rougher flotation parameter evaluation and cleaner circuit evaluation, through to locked-cycle testing and pilot plant design and operation. Ore variability and modeling to determine the response of various ore types to the optimum conditions established is also examined.IntroductionA carefully planned laboratory test program is essential for the successful development of any sulfide flotation process. These programs usually begin with a series of batch tests on several ore type composites to evaluate appropriate reagent schemes and delineate optimum rougher flotation conditions, such as primary grind size, flotation pulp density, flotation pulp pH and retention time. Cleaner parameters such as regrind size requirements, cleaner pH, pulp density and number of stages are then defined. Semicontinuous locked-cycle tests are performed using the parameters established in the batch tests to determine the effect of middling streams recirculation on flotation performance. The data generated and the experience gained in the locked-cycle tests may be used to design and operate a continuous pilot plant if relatively large amounts of concentrate are required for further process development, such as optimization of byproduct molybdenum production from bulk copper-molybdenum concentrate.A comprehensive ore variability program is undertaken to determine the response of various ore types to the optimum conditions established. These ore variability programs often test hundreds of samples in standardized batch rougher and cleaner tests to ensure that the orebody is well understood.This article describes the development of a copper-molybdenum flotation process, but the concepts discussed can be applied to most sulfide flotation systems and many industrial minerals projects. The block flow diagram in Fig. 1 provides an overview of the development process."

Jan 1, 2016

By G. Wang, L. R. Moore, Y. Xiong, A. Gorken

"Feldspar may represent 60% of the earth’s crust, but the mineral does not exist in a pure state. It is generally associated with quartz, iron containing minerals such as mica, and titanium containing minerals such as rutile. Feldspar itself can even exist in different lattices from those containing sodium to various divalent ions. As such, its beneficiation has become a process that is quite complicated, when compared to the beneficiation of other minerals. It is this complexity that has made feldspar beneficiation dependent on tailor made reagents to successfully yield the industry specified feldspar products. This paper reviews the mineralogical variations found from two feldspar mines and the development of collectors to specifically target a Fe+Ti concentration of < 0.05%, while maintaining a feldspar recovery greater than 90%.INTRODUCTION Feldspar is a class of aluminum silicates that represents the most abundant mineral on earth (Vidyadhar, 2002). This class of mineral can further be defined by the types or concentrations of cations present in the crystal lattice, MAlSi3O8 (M = K, orthoclase and microcline; M = Na, Albite; M = Ca, Anorthite) (Heyes, 2012). Feldspar is most commonly mined and processed for either the alumina used in glass making or for the alkalis used in ceramics. The alumina is known to improve product hardness, durability, and resistance to chemical corrosion. The alkalis act as flux, which means they not only lower the melting temperature of the mineral mixture, but also assist in connecting the other components present in ceramics. It was stated in 2009 that the world production of feldspar was in excess of 18.3 million tons produced, with the majority coming from China, Italy, and Turkey. Raw feldspar is typically found with quartz, iron containing minerals such as mica, titanium containing minerals such as rutile, and other feldspar minerals (Celik, 2001). Quartz is stated as having a negative effect on the melting point of the feldspar, whilst the iron and titanium based mineral contaminants are known to have negative effects on color and quality of the product produced; these mineral contaminants must therefore be separated prior to application (Barns, 1997 & Celik, 2001). Mineral flotation and magnetic separation are the most common means of feldspar beneficiation. However, conditions vary greatly from mineral contaminant to mineral contaminant (Table 1). Some literature suggests feldspar can be floated with an amine, but this generally yields lower than acceptable recoveries and often still requires the magnetic separation of iron based minerals to achieve the desired grade (Amarante, 1997 & Heyes, 2012). Feldspar flotation can be further improved with the addition of hydrofluoric acid (HF) as a silica depressant and feldspar surface modifier, but this still requires the removal of some of the other minerals first. Rutile can be floated with an anionic fatty acid collector at a pH range of 7-8 or with a petroleum sulfonate at a pH < 4 (Celik, 2001), while mica can be floated with a petroleum sulfonate or an amine collector at a pH of 3.5."

Jan 1, 2016

By J. C. Reid

Pre-cambrian scheelite deposits in Northeastern Brazil are widespread in a high grade metamorphic terrain. Previously these deposits had been interpreted as contact-metasomatic. In this paper, a volcanigenic model is invoked based on the volcanic setting (proximal to distal) and the absence of associated felsic intrusives and spatially associated metasomatic skarns. The tungsten was introduced into sediments by volcanic- exhalative processes and subsequently remobilized and further concentrated by heat and metamorphis fluids associated with high-grade metamorphism and migmitization. An alternative syngenetic - diagenetic model is discussed which requires the transport of tungsten by heteropoly acids and deposition of the tungsten as a function of Eh and Ph conditions and different clastic depositional environments. While such stratabound tungsten deposits are considered rare in North America, the hypotheses developed in this paper may open new areas for exploration.

Jan 1, 1983

By L. Sandbak

"CURRENT BASIS OF GROUND SUPPORT DESIGN ANALYSIS The current strategy used in determining what kinds of support are needed is based on empirical design charts (Grimstad and Barton, 1993). Figure 1 is an example of the topcut analysis used for a 14 foot wide (4.3 meter) drift, which is the current design width used for topcuts at TRJV mine. The majority of our topcuts are situated in ore of the Type IV and Type III weak rock class categories that necessitate the use of bolts, mesh and 2”-4” of shotcrete. This type of empirical chart gives excellent guidelines for the kinds of support, and it is based on case histories of civil tunneling and mining properties. It is a good starting point for determining the kinds of support needed, but not to the detail needed to optimize the number of bolts, type of mesh, or combination of types or strengths of shotcrete. This report is an attempt to help quantify the safety factor and optimum design parameters to include mesh and shotcrete as part of the design criteria and subsequent safety factor.SAFETY FACTOR ANALYSIS: BOLTS ONLY One type of safety factor analysis used at TRJV for the past 7 years is described as the “dead weight” method, developed by Pakalnis (2008). It involves the support of a conservative “dead weight” of rock held in place by bolts in which the depth of failure is approximated as a wedge whose height is one-half of the span. The failure or dead weight wedge resembles a triangular wedge that must be supported by the remainder of the bolts going through the wedge (see Figure 2).The support capacity of the system is determined by the bond strength of the bolts holding up the wedge, which is in turn based on the RMR. The method assumes the total support capacity is the sum of the individual bolt values defined by either the breaking strength or the bond strength of the bolts (whichever is lower) passing through the failure surface."

Jan 1, 2017

By Yi Luo, FENGLIANG WU

Explosions and fires originated from longwall gob due to the formation of methane-air mixture have been a severe threat to coal miner’s lives.Many numerical studies on coalmine fire and explosion hazards have focused on the airflow in roadways and mine gobs. However, most of these studies isolate the gob from its surrounding roadways, and the network analysis and the CFD method are applied independently tomodel the two classes of airflows. This approach greatly limits the ability of simulatingmine ventilation flow, especially unable to consider the effects of gob boundary conditions on air exchange between the gob and the surrounding airways. An innovative finite tube method (FTM) is developed to couple the one-dimensional mine ventilation network (MVN) and the 2D/3D gob flow field (GFF). In FTM, GFF is discretized into a finite number of flow tubes each of which is formed by any two adjacent stream lines. These tubes, representing the gob’s field flow, connect the MVN into a new coupling network. To solve the coupling model betweenMVN and GFF, an iterative solution technique is developed inwhich the MVN analysis is used to evaluate the boundary pressures for GFF simulation and in turn the FTM feeds the GFF results back to the coupling network. Based on the FTM approach, a model for gas migration in gob has been established for delineating the hazard zones of explosive methane concentration and spontaneous combustion. A computer program is developed to implement the FTM simulation. An illustrative example with five flow tubes representing the GFF is created to verify the stability and convergence of the FTM solution process. A simulation example also indicates that the accuracy of FTM is improved by 12% compared with previous method. Results of an application case show that the program is capable of quantitatively evaluating the gob’s risk zones prone for spontaneous combustion and gas explosion as well as performing risk analysis for various ventilation scenarios.

Jul 10, 2020

By P. Nelson, R. O’Connell, J. Rostami

Tunnel boring machine (TBM) system utilization is a critical factor for predicting machine performance. The process of estimating machine performance, including rate of penetration (ROP) and machine utilization (U) must incorporate an understanding of site geology, TBM specifications and site management. The study herein presents a preliminary analysis of the different activity time and downtime components from hard rock TBMs at two project sites to evaluate their impact on machine utilization. A comparison of crew experience, first between shifts and then between projects is included to analyze its effect on utilization and downtime. This work presents the sensitivity of the utilization factor to selected activities in the projects and the impact of geology and site set-up/logistics on machine performance.

Jun 13, 2021

By J. Kretschmann, K. Sakamornsnguan

"Sustainable development is an influential ethical concept in modern mining management. However, the concept is not culturally neutral because it is based on Christian, Western values. These values can be very different from traditional values in emerging mining countries like Thailand, where Buddhist values are dominant. When applying the concept of sustainable development, these differences should be taken into account. Different values imply different interpretations of ‘good mining’. They have a significant impact on how mining operations are evaluated, perceived, operated and managed. This paper attempts to integrate Buddhist principles with approaches of the sustainable development concept. When local values are appreciated and maintained, mining companies and their external stakeholders can identify objectives and approaches that match with their own values and contexts. Practices based on this integrated ethic can help to promote sustainable mining and to minimize communication risks for enterprises in mining countries like Thailand. INTRODUCTION The objective of this paper is to integrate Buddhist principles to the application of sustainable development concept to mining activities. The structure of this paper is divided into four parts. An introduction provides basic information about Thailand, its mining industry and the role of Buddhism on the past development. The second part compares the differences between the sustainable mining framework and the implications of Buddhist principles on mining. In the third part, the core Buddhist teachings are integrated into the sustainable mining framework. This is followed by conclusions in the last part. THAILAND, BUDDHISM, AND MINING Thailand is a constitutional monarchy state in Southeastern Asia with a population size of around 65 million [1]. Its GDP in 2013 was 391 billion USD [2], predominantly deriving from manufacturing (38%), trade, transport and communication (24%), agriculture (8%) and mining and construction (4%). Still the largest part of the Thai workforce (39%) is working in the agricultural sector. The remaining part of the workforce is equally distributed across services, manufacturing, and mining and construction sectors. [3]"

Jan 1, 2015

By Saurav Kumar, Akshay Kumar, Vinayaka R. Kiragi, M. K. Banerjee, Amar Patnaik, Vinod Kumar

Today’s industrial technology offers to optimize and reutilize the resources available in terms of scum that remains after hot rolling in steel rerolling mills in Rajasthan, India. Vast reserves of low-grade coal exist and tons of mill scale are produced everyday after hot rolling in steel rerolling mills in Rajasthan, India. The present research work aimed to optimize the various parameters of solid-state reduction of mill scale using low-grade coal from Rajasthan, India. This study investigates the effect of reduction temperature (850–950 °C in steps of 50 °C), reduction time (60 to 180 min, in step of 60 min), mill scale size (800– 300 μm), and mill scale to coal ratio (1:1, 1:2 and 1:3) on achievable metallic iron percentage and its metallization. A higher percentage of iron content is obtained at a lower particle size of 300 μm. The structural analysis is carried out on 300 μm mill scales using XRD analysis, which shows the percentage of iron is approximately 63%, and metallization above 80% can be obtained under the reduction temperature at 900 °C for 180 min, for 1:3 ratio (mill scale to coal ratio). The chemical composition of the mill scale is obtained using X-ray fluorescence (XRF), and particle sizes as well as distribution of mill scale are determined by scanning electron microscopy (SEM). The elements present in the mill scale are also verified using EDS, which indicates the presence of a major portion of Fe, followed by Fe2O3, Si, and C, respectively.

Aug 14, 2020

By D. H. Garcia

The mining industry responded to public concerns about use of cyanide by developing a voluntary certification to allow companies to demonstrate their commitment. The International Cyanide Code (Code) establishes standards for the manufacture, transportation and use of cyanide. Key concepts in closure planning to comply with the Code are to decommission all facilities related to cyanide operations and to provide a financial assurance mechanism for those activities. Code requirements may differ from state-specific regulations, but requirements are based on closure goals for protection of the human health and the environment. Only issues related to cyanide operations are required to be included in decommissioning demonstrations. For example, the disposal method of cyanide solution holding tanks and the cost must be included in the closure plan, but information regarding closure of roads is not required. Closure costs must be based on a third-party contractor as opposed to internal budgets. Compliance with the closure requirements of the Code allows companies to show their stockholders, lending institutions, and the public that their operations are environmentally responsible.

Jan 1, 2010

By J. D. Miller

"Bastnaesite is one of the important mineral resources for the production of rare earth materials, and it is typically associated with calcite and quartz as gangue minerals. Fatty acid or hydroxamic acid are recommended collectors for bastnaesite flotation. In this research, potassium lauryl phosphate was expected to provide a stronger flotation response for bastnaesite than for the calcite and quartz gangue minerals. Using potassium lauryl phosphate as collector, the results of captive bubble contact angle measurements, zeta potential determinations and microflotation experiments for bastnaesite, calcite and quartz are reported. Greater selectivity for bastnaesite was achieved using potassium lauryl phosphate than using octyl hydroxamate as collector. These results indicate that potassium lauryl phosphate might be a promising collector in the flotation of bastnaesite ores. The computation results of universal force field (UFF) interaction energies for the mineral-reagent interactions are also reported and were found to correlate well with the experimental microflotation results.IntroductionBastnaesite ((Ce,La)FCO3) belongs to the mineral class of semisoluble salt minerals, whose characteristics include ionic bonding and limited solubility in water. Bastnaesite, for the most part, contains the cerium subgroup or the lighter rare earth elements (Zhou et al., 2014). The Mountain Pass deposit in California in the United States and the Bayan Obo deposit in Mongolia in China are the two major deposits of bastnaesite (Azizi et al., 2016; Satur et al., 2016). Calcite and/ or quartz are common gangue minerals in these and many other rare earth deposits (Jordens et al., 2014)"

Jan 1, 2017

By S. Grogan

Next year marks the tenth anniversary of the Surface Mining Control and Reclamation Act (SMCRA). As the U.S. coal industry scrambles to cope with serious economic difficulties, it is appropriate to examine some other difficulties that have their origin in certain provisions of that ten year old law, and that bear directly on the economic viability of surface coal mining in the west. This paper focuses briefly on three technical issues in the reclamation of surface coal mines in arid regions, and suggests that innovation can resolve these issues. The coal industry operates within a narrow legal context, defined in 1977. In enacting SMCRA, Congress listed among the purposes of the Act ?... to...strike a balance between protection of the environment, agricultural productivity and the Nation&apos;s need for coal as an essential source of energy." I maintain that such a balance has never been struck, particularly with regard to the reclamation of mines in the west. One reason is that when SMCRA was enacted its supporters were aware of uncertainties about the potential for successful reclamation of western surface mines. Over the intervening years, as a recent Congressional study report (OTA, 1986) points out, "...the risks these uncertainties may pose to the long term success of western reclamation have been reduced significantly." Unfortunately, SMCRA&apos;s enforcement agency, the Office of Surface Mining (OSM) has not yet recognized this fact, and the western coal industry is paying the price.

Jan 1, 1986

By Goutam H. Shahani

The current economic downturn has been at the center of media attention for several years. Today, the mining and mineral sectors are being impacted by highly fluctuating supply-and-demand conditions, extreme price volatility and tremendous market uncertainty on a world-wide basis. There have been numerous plant closings, project cancellations and employee layoffs. In this gloomy economic environment, it is easy to forget that the world?s gross domestic product (GDP) has more than doubled in real terms during the last 30 years. While current market turbulence may continue for some time, the long-term trend is unmistakably upward. Living standards are rising all over the world, thereby creating demand for food, clothing, transportation and housing. This translates into tremendous demand for the mining and mineral sectors. In the future, new capacity and plant expansions will be necessary to meet this need. These investments, which typically have a life span of 30-plus years, will have to be based on long-term economic considerations rather than current market conditions.

Jan 1, 2011

By Ehab Gomaa, K. A. El‑Nagdy

Backfilling material such as tailing (mine wastes) mixing with cement or gypsum has grown throughout the world’s underground mines. However, despite their growing popularity, the typical hydraulic and mechanical fill types utilized in many mines still exist. Deep underground mining has increased due to the lack of commercial minerals nearby. Mine wastes were considered the main part of backfilling to prevent environmental pollution, ground subsidence after mine abandonment, and mine collapse during deeper extraction phases. The cemented backfill technique is the principal technique used in underground mines, which include cement with fly ash and/or filter dust, cement with tailing material and fly ash, gypsum with fly ash, and synthetic anhydrite with fly ash and have been reviewed. It has concluded that a backfilling material must be selected based on further goals, available material near the mine site, and economic factors. This paper analyzes different backfill material mixtures to create a technique that will increase safety in underground mining conditions and foresees an appropriate formula that gives high uniaxial compressive strength. The multiple linear regression (MLR) on the collected data from the experimental works to construct the relationship between the uniaxial compressive strength (UCS) of the mixture and the components of the backfilling and the prediction formula for expected compressive strength was obtained. The results revealed that the predicted regression equation was robust and reliable to predict the (UCS) for the new components of the filling (cement (CE), filter dust (FD), water content (WC), and time (T)).

Oct 3, 2023