Search Documents

By J. Partyka

Adequate ventilation is a main concern if Lockerby Mine near Sudbury is to be expended. This study investigate a two-fold problem: (1) the new pressure and volume requirements of the main fans due to the theoretical. deepening of the mine, and (2) the effect of the natural ventilation pressure on the main fans. Field data was analyzed with the aid of a newly developed network simulation program, VNETPC Version 3. 0. The density change throughout the mine is accounted for by performing all computations at reference density. Results of the investigation indicate that the existing fan system must be supported by three to five additional underground fans as well, the density effect is significant. If neglected, it will greatly alter the simulation results

Jan 1, 1991

By Robert Cooke

This paper shows how technology developed to analyse stabilised slurries can be applied to paste flows. The rheological characterisation of paste mixtures using the generalised yield pseudoplastic rheological model is described. It is noted that the slump test does not provide a complete rheological characterisation of a paste. Methods for calculating pipeline pressure gradients for laminar and turbulent flow are presented. The minimum pressure gradient is an important consideration to ensure that solids do not settle on the pipe invert. Important points to be considered for a pipe loop test programme are noted. The usefulness of the pseudo shear diagram for scaling pipe loop test measurements is demonstrated. Issues to be considered for the design of paste reticulation systems are discussed.

Jan 1, 2001

By Graham Andrews

Experiment shows that the microbial degradation of pyrite does not necessarily proceed stoichiometrically. Under some conditions sulfur is oxidized preferentially leaving something approaching iron in composition; under others, the pyrite is converted almost to elemental sulfur. A kinetic model for the process based on three elementary biochemical reactions can explain these observations. The diffusion of sulfur along grain boundaries and dislocations in the solid pyrite uncouples the oxidation rates of sulfur and iron from the requirements of stoichiometry. This mechanism also explains qualitatively why bacteria adsorb preferentially at dislocation sites on pyrite surfaces, why they form "pits" at these sites, and why amorphous pyrite is more readily degraded than pure crystals. The rate-limiting step for pyrite oxidation is discussed

Jan 1, 1989

By Robert E. Carver

Opaline clays from central and eastern Georgia are widely used as industrial and domestic absorbants, principally as insecticide carrier and animal litter. The clays are classified as fuller's earth, although they &e somewhat atypical of the group, since opal (cristobolite) is commonly the dominant clay-sized mineral. A preliminary investigation of absorption characteristics indicated that water vapor absorption (264 days) is' related to opal content as determined by x-ray diffraction peak height ratios. Ethylene glycol vapor absorption is related to montmorillonite content. Contact absorption of water is complexly related to surface absorption, porosity, opal content and montmorillonite content, and may be as great as 112% of the original sample weight. The most absorbent clays are highly porous (to 65%) and contain both montmorillonite and opal.

Jan 1, 1972

By Edward B. Westphal

One of the purest gypsum deposits in the United States is located in northwest Oklahoma about 90 miles northwest of Oklahoma City. Gypsum beds of the Blaine Formation (Permian) are each 10 to 15 feet thick and 97 to 99 percent pure; they are being quarried by four companies in the area. Most of the stone mined by U.S. Gypsum Company is calcined for the manufacturing of wallboard and special plasters, but some of the crude gypsum is marketed for cement manufacture and for use as soil conditioner. Reclamation of the mined lands at Southard, Oklahoma, has been carried out since 1968, and the company is now involved in a cooperative program of land revegetation to aid in erosion control, provide for wildlife, and for beautification.

Jan 1, 1978

By Mark W. Springett

The examination of relatively well behaved distributions subject to truncation by a cutoff grade in the mine clearly demonstrates that a bias is inevitably introduced when the selection is based on the results of samples which are subject to even the most idealised error distribution. The idealised error used in this paper is assumed to be normally distributed with a mean of zero and is thus unbiased. The bias introduced can be minimised but it cannot be eradicated. A better understanding of the bias can lead to improved procedures for mine sampling, sample preparation, assaying and estimation of selection units which will not only reduce the discrepancy but more significantly will increase the efficiency of mining selection and hence profitability.

Jan 1, 1989

By Timms. Greg P., John W. Bennett

A field-based method for measuring the diffusive oxygen flux through covers placed on sulfidic waste rock dumps has been developed and applied at a number of mine sites. The technique provides a means of quantifying oxidation rates in dumps and can thus be used to assess the effectiveness of cover systems. Two instruments can be used. The first is portable and easy to set up, enabling a picture to be built up of the overall diffusive flux into a dump by making measurements at a sufficient number of locations. The second is installed beneath a cover and is preferred in situations where oxygen is consumed in the cover since it provides a direct measurement of the oxygen flux into the underlying waste rock.

Jan 1, 2000

By Mitchell J. Willis

Recovery of fine particles has been considered to be a major limitation of the classical flotation process. However, the beneficiation of kaolin, a naturally occurring fine ore, via flotation has been practiced over the last 40 years. Kaolin is valued as a white pigment, and therefore, the goal in kaolin flotation circuits is to remove the colored impurities to result in an acceptable brightness product. Kaolin flotation originated with a novel carrier flotation process, and later on carrier less flotation techniques were developed. The collector chemistry utilized to beneficiate kaolin is based on fatty acids, and recently hydroxamates have been successfully used. The purpose of this paper is to cover the flotation practice in the kaolin industry in terms of the history and the reagent schemes.

Jan 1, 1999

By Roe-Hoan Yoon

Froth flotation is widely used for separating particulate materials from one another in aqueous media. The basis of this important separation process is to control the hydrophobicity of particles. However, it is difficult to predict the kinetics of flotation based on contact angle (?), which is a thermodynamic property. A solution to this difficulty would be to develop a relationship between ? and the gradient of the hydrophobic forces across the solid-liquid and bubble-liquid interfaces. Such information can be obtained using the surface force apparatus (SFA), the atomic force microscope (AFM), and the thin film balance (TFB). The present communication reviews the results of the measurements conducted using these methods, and offers a methodology for deriving a rate equation for bubble-particle interactions

Jan 1, 1999

By M. H. Al-Dabbagh

In this paper, the authors outline the deficiencies of PERT/CPM as a method for scheduling complex projects such as mine development. In particular, PERT/CPM networks cannot accommodate logical nodes (events) or stochastic branches (activities). The Graphical Evaluation and Review Technique (GERT), developed by Pritsker and. co-workers, is introduced as an alternative to PERT/CPM that overcomes many of the deficiencies of the latter and enables a more realistic analysis of complex projects that are subject to significant uncertainties. A brief overview of GERT network structures and network analysis is given and a PC implementation of the method is described. The technique is illustrated by application to the development of an open-pit gold mine in Saudi Arabia.

Jan 1, 2002

By Jan M. Mutmansky

While production scheduling for both surface and underground mining operations is similar in nature, a rather large array of techniques is applied in solving such planning problems. The techniques consist of both rigid operations research (OR) methods and practical procedures which are not mathematically based. In the following sections, a short summary of some of the techniques that are applicable to production scheduling problems in mineral operations is presented. The techniques discussed are: linear programming, integer programming, dynamic programming, graph and network theory, simulation, and heuristic methods. For an in-depth comprehension of these techniques, the reader is referred to any of the available textbooks on these subjects. One or more references will be listed for each topic to provide a starting point.

Jan 1, 1979

By Robert M. Belesky, H. R. Hardy

A methodology to detect the presence and monitor the stability of shallow cavities is presented in this paper. The approach incorporates surface-wave seismic and acoustic emission/microseismic (AEIMS) techniques. Application of tomography to the seismic data is made to enhance the ability to locate cavities. Zonal and hit-sequence location techniques are introduced into AE/MS monitoring schemes. These source location techniques simplify the analytical procedure yet still provide sufficient information regarding the region of AE/MS activity. The concept of unique velocity data for conventional, least-squares, source location routines is discussed. A hypothetical case utilizing the algorithm is presented. The method described has been successful based on preliminary studies. Areas of current and future research are identified.

Jan 1, 1986

By H. Para, A. Aguirre, G. Artadi

Mining is a very important economical activity in Peru which has been recently developed without considering environmental aspects. Here, we show an experience at the Milpo mine, situated 4,200 meters above sea level; a mining company that has the value of being one of few from the last decade that is engaged in consolidating a model of environmental protection. The model includes aspects of contamination prevention and control, with bioindicators such as pasture cultivation, vegetables, forests, and hydrobiological species breeding. Socially, through means of development programs in natural areas, forestation and support to rural agriculture, together with environmental education, it is being demonstrated that it is possible to ensure tangible results in environmental conservation and the well-being of the populations around the mine.

Jan 1, 1998

By C. W. Matthews

Introduction Screening is defined as a mechanical process which separates particles on the basis of their size and their acceptance or rejection by a screening surface. The key element in this method of particle sizing is obviously the screening surface, the medium that contains the apertures for the passage of the undersize material. This surface must be strong enough to support the weight of the material being screened, flexible enough to yield to the vibrating force applied to it, yet light enough to provide a reasonable ratio of open area to attain a practical through- put. To balance all of these factors is difficult enough. The problem is compounded, however, because screening media are made in a great variety of types, shapes, sizes, and materials of

Jan 1, 1985

By K. P. Stricker, H. Keddeinis, K. Grebe

Recent investigations by Mannesmann Research have shown that disintegration of sinter with widely varying quality levels is subject to a much more complex set of influences than was previously assumed. It was confirmed that disintegration at temperatures between 300° and 600°C (570° and 1,110°F) is triggered by the degradation of hematite. The specific tendency of hematite to disintegrate is, however, not constant: sinters containing the same amount of hematite can show widely differing disintegration tendencies, depending on structural homogeneity, porosity, and gangue quantity. Sinters with heterogeneous structures transmit stress to the hematite phase and this favors disintegration. Another factor is the brittleness of the glassy silicate phase, which can be influenced even by small modifications of minor gangue constituents.

Jan 2, 1984

By M. Bleeck

Calcium carbonate (CaCO3) is one of the most ubiquitous and versatile minerals found in the earth's crust. Its availability, attractive physical properties and relatively low processing cost make CaCO3 the most widely used filler material today. It is mined in three different forms - chalk, limestone and marble. Each physical form of CaCO3 has different qualities due to differences in postdepositional geology. But the chemical composition remains the same, with CaCO3 an inert component of the finished product. In the past, the paper industry largely left CaCO3 by the wayside, as it cannot withstand the acid-based papermaking process. But conversion to an alkaline system by many US mills changed this picture. Carbonate suppliers have put time and effort into research and development, demolishing barriers and creating new possibilities for what is a simple, natural product. By controlling particle size, size distribution and particle charge, the industry uses ground calcium carbonate (GCC) as a performance enhancer and as an extender for more expensive ingredients. It is estimated that the United States uses 3.6 to 4.1 Mt/a (4 to 4.5 million stpy) of CaCO3. Consolidations and mergers are taking place in the industry. Of the 12 major GCC producers in operation nine years ago, seven are left. Mineral Technology (US) is the dominant precipitated calcium carbonate (PCC) producer with more than 50 satellite plants worldwide. Other producers include Georgia Marble (French); Franklin Industries (US); OMYA (Swiss); J.M. Huber (US); ECC (English); and Filler Products (US). Global Stone PenRoc (Canada) is the only newcomer. In addition to this group, there are three small producers left in North America, each with a capacity of less than 100 kt/ a (.110,000 stpy). The trade organization operating as the Pulverized Limestone Division of the National Stone Association renamed itself the Pulverized Mineral Division, to increase its membership pool. The US paper industry is a predominant GCC con¬sumer, using approximately 800 kt/a (882,000 stpy) at an approximate cost of $130/t ($1.43/st). European paper mills pioneered alkaline papermaking. In the early 1960s, they began using GCC as filler and soon thereafter added GCC to their coating formulations. A decade later, the North American paper industry followed suit. The conversion from acid to alkaline paper production benefits the economic and performance aspects of the industry. Less pulp is needed, paper machine maintenance and effluent treatment costs are reduced, and sheet strength, opacity and brightness are increased. Perhaps most important to the reader, the sheet is desensitized to ultraviolet light, extending the paper's archival ability. CaCO3 can provide the papermaker with additional control of his paper. For example, PCC has long supplied the tobacco industry with a means to slow down the burning rate of cigarettes. Due to enhanced performance with regard to bulk and opacity, filler PCC use has risen to 1,500 kt/a (1,650 stpy) in the United States, at an approximate price of $130/t ($143/st). The majority is produced onsite at the paper mill, using "satellite plants." This concept reduces freight cost because only quicklime (CaO) is shipped to the mill, not CaCO3 slurry. The future of CaCO3 is encouraging. The amount of natural ground CaCO3 used is expected to double by the year 2005 to approximately 8 Mt (8.8 million st) worldwide. Acid papermaking practices will feel an increasing pressure to convert to an alkaline process as larger volumes of GCC containing paper enter the recycling market. CaCO3 reserves are plentiful. They will supply the ever growing demand for increasingly sophisticated paper. The plastics industry is supplied with almost 900 kt/ a (990,000 stpy) GCC at an annual growth rate of 4% to 5%. The price of a functional, inorganic filler, surface modified for the plastics industry, has an average selling price of $220/t ($243/st). GCC represents the most common filler, creating a product with higher gloss, better dielectric properties, impact resistance, weatherability and shrinkage control. CaCO3-filled plastics surround us - auto hubcaps and dashboards, shower enclosures, floor tiles, wire coatings, microwave dishes and Tupperware. The caulking and sealant industry is an enormous GCC user, with annual consumption requiring 1.13 Mt (1.2 million st) at about $44/t ($48.50/ st). Caulking and sealant may be highly filled with GCC yet undergo no adverse flow effects, with a narrow particle-size-distribution filler decreasing the binder demand. The CaCO3 industry, as well as the carpet industry, are more or less tied to the growth rates of the construction industry. It is estimated that the carpet industry uses some 680 kt/a (750,000 stpy) of GCC at about $25/t ($27.50/st). The paint industry uses approximately 300 kt/a (331,000 stpy) at a 1 % to 1.5% annual growth rate. Here, too, GCC is the dominant filler. It is used to enhance flow characteristics and color uniformity. It also extends costly titanium dioxide, creates sheen and controls roughness, hardness and tack. More CaCO3 should be used in the future as industry shifts from solvent-free or water-based formulations that can accommodate higher GCC volumes. CaCO3 is not imported or exported in any great quantity. Most areas have reserves of their own and the selling price is relatively low. Even so, quality varies from deposit to deposit. As our needs become morespecific, it remains a challenge to provide varying industries with a fitting product.

Jan 1, 1998

By Milton H. Ward

The percentage of exploration dollars flowing out of the industrialized countries continues at an all-time high, and this shift in risk money is justified (Samuels, 1990; Bosson, 1977). Clearly, the odds of discovery are greatly enhanced if exploration is pursued in an untrampled and geologically more prospective environment. Unfortunately, such major unexplored areas of the developed world are shrinking rapidly, not just because the lands have already been tested, but primarily because they have been withdrawn from exploration. Experience, however, has shown that foreign investment is not without risks. These include problems that result from working in isolated areas, a lack of infrastructure, untrained workers and an absence of a solid geological data base. While the likelihood of once-feared expropriation is now low, mining enterprises still must take precautions to gain the support of their constituencies, including a variety of governments (local, provincial and central), workers, environmentalists, cultural organizations and local landowners. Is foreign exploration worth the risk? In most cases, Yes! But maintaining tenure and long-term success in a less developed country is only likely with good planning and the use of appropriate safeguards. These include measures such as buying country-risk insurance, building multinational relationships, forming joint investments, developing a broad customer base and seeking local investors in the company (Cobbe, 1979). The primary theme of this lecture is: How a company handles its constituency is critical to long-term tenure in a foreign country. Ideally, a multinational mining company would be so effective in dealing with the local people and managing its relationship with the host government that it would become a preferred employer, preferred over its competitors and over local companies. Historical overview Our earliest ancestors lived in Africa three to four million years ago. The Paleolithic or Old Stone Age, about 500,000 years ago, marked the beginning of mining in its earliest form (Gregory, 1980; Wolf, 1984). Various types of rocks and stones were used for tools and weapons, with flint being the preferred resource for implements. Initially, these materials were collected as stones (eoliths) lying on the surface. Then they came from excavations of flint in limestone beds that were exposed in river banks or naturally occurring excavations. Later, more formal mining developed. No doubt tribes of the Old Stone Age experienced conflict over rights to eoliths, food and land. The question of who owns the land and has rights to its contents and what is fair value for extraction is still the subject of intense debate and, occasionally, open conflict. As time passed, the search for useful minerals required migration from one area to another. Later, voyages from Europe to the New World and travels to other remote regions were funded and supported by absentee investors, kings and such (Rogers, 1976). The primary objective of such funding was to obtain gold, silver, food stuffs and other commodities that could be collected from the new countries. This is still the objective of foreign investment.

Jan 1, 1994

By P. Ollivier

The ore-processing plant of the Soremib mine Pour a (Burkina Faso) has now been in uninterrupted operation for 3 years. Ores from the oxidized and non-oxidized zones of the deposit are processed together in one flotation unit. About 60% of the gold is free and is recovered in a gravity processing unit. The residual gold in the flotation concentrate is processed on the spot by cyanidation and carbon-in-pulp.

Jan 1, 1998

By Roy Eric Lurie

Computer based signal processing techniques for obtaining empirical dynamic models from measured mill circuit data are discussed. This modelling is the first step towards designing a particle size control strategy. Experimental data from a computerized acquisition sys tern is examined and analysed, and a number of model identification procedures are applied. The resulting models are compared and a suitable model is selected, illustrating the benefits of computer tools for control system design.

Jan 1, 1992

By M. J. Mrugala

Typically the conventional pillar design methods consider the behavior of the pillar alone. In such analysis the contribution of the associated roof and pillar is not considered. The focus of this paper is a study of pillar behavior in the context of interaction between a different rock material sequence in the associated roof and floor. The finite difference element code FLAC (1)is used to perform modeling of pillar response to various stratigraphic sequences.

Jan 1, 2003