Search Documents

By A. Russell, M. N. Hughes, Jack Barrett

The bacterial oxidation of arsenopyrite has been shown to be an efficient, economic and environmentally acceptable method for the liberation of any gold content . The mechanism of the process is not certain but is usually considered to involve direct and indirect reactions with respect to bacterial involvement. The direct reactions are those in which the bacteria attached to the mineral surface cause its dissolution, with dioxygen being the oxidant. The iron(III) produced in solution is the chemical oxidant in the so-called indirect reactions. Barrett et al 2 showed that a synthetic bio-oxidation solution (with no cells present) could dissolve up to 15% of an arsenopyrite sample, the products of the chemical oxidation being iron(II) and arsenic(III). This paper describes an extension of the investigation of the chemical process and its imp! ication for the mechanism of the bio-oxidation of arsenopyrite.

Jan 1, 1990

By Rod Knopp

Each year approximately 5,000 tons of a sulfide concentrate grading 1 ounce gold per ton are produced at this operation. The material is refractory and as shipping costs and custom smelter charges increase, options to process it on site are becoming more attractive. Three methods of treating the ore have been investigated in detail. The first option of ultra fine grinding the concentrate produces a 35% gold recovery with relatively low capital and operating costs. A second option of pressure oxidation is very capital intensive and has high operating costs but recoveries in the order of 95% are achievable. The final option, biological leaching offers both capital and operating costs which are less than pressure oxidation, while still achieving 90% gold recoveries. Bioleaching of gold concentrates has been gaining acceptance but there is a risk factor associated with this or any emerging technology.

Jan 1, 1990

By Stephen Young

The continuous monitoring of free cyanide levels is an important part of gold recovery operations. Accurate and up to the moment knowledge of the free cyanide concentration can result in substantial cost savings by allowing reduced concentra­tions with lower fluctuations, while maintaining or increasing gold recovery. Reduced free cyanide levels also result in lower detoxification costs at the mill discharge which translates into further savings while meeting environmental requirements. As can be seen from the upper curve in Figure 1 (which is based on in-service measurements), without accurate monitoring and control, cyanide concentration fluctuates during the produc­tion cycle, and is maintained at a high level to err on the side of caution. The lower curve illustrates the improved control permitted by the installation of a CY ANCOR, giving a more consistent concentration over the process cycle, and safely allowing use of a lower concentration.

Jan 1, 1995

By D. R. East

Recent experiences within certain sectors of the international mining industry suggest an underestimation of the environmental risk associated with the design of mine waste management facilities. These experiences show that the technical and managerial challenge of responsible mine waste management is not always fully appreciated. Unfortunately, the image of the mining industry's environmental performance is negatively impacted by a relatively few number of failures. This negative view overrides the many positive contributions made by the majority of mining companies. The fact that these failures continue to occur to this day in both developed and developing countries is indeed remarkable, and indicates a degree of risk-taking approaching unacceptable levels. The design requirements for tailing storage facilities are, in many cases, more demanding than those of conventional water dams, because seepage of fluids which contain dissolved metals may pose a greater threat than the mere loss of water.

Jan 1, 1999

By G. Capello

Carboniferous mining basins are today a non-negligible source of energy. So important in fact that returns now justify high investments and costs even for those deposits that were un-economical in the past. Nowadays, if properly explored and exploited, basins previously considered non-minable due to complex structural and stratigraphical situations may be economically interesting. It is while studying a faulted basin with such features that the Authors developed the described computer-aided methodology capable of constructing a model of the physical structure of coal deposits on the basis of stratigraphical data from drillings. The aim of the procedure is to define coal reserves, the exploitation of a deposit being conditioned by the possibility of identifying zones that are technically minable. This objective is pursued by making as detailed a reconstruction as possible of the geometrical, stratigraphical and tectonic features of the coal-bearing seams of a deposit.

Jan 1, 1982

By Hugh E. Cronin, John Ramage

The recommendations resulting from a Dispute Review Board (DRB) hearing of a contract dispute are being challenged more and more frequently. This paper explores possible causes based on the authors’ experiences. Challenges facing the DRB process include: The DRB process is starting to lose some of the informality and flexibility. Both owners and contractors appear to be putting too much weight on a board recommendation on a dispute. DRB’s do not make “decisions,” they provide recommendations for dispute resolution to both parties. The DRB process is not just for contractors to present an unresolved issue to a board hearing. Owners can also initiate a request for a hearing on a disputed issue. For the DRB process to remain a viable element of the successful construction project, confidence must continue to be maintained in a process that is intended to work on behalf of both parties to the construction contract.

Jan 1, 2003

By Jim Avraamides

Historically, much of Western Australia's gold production has come from the refractory sulphide-telluride ores located in Kalgoorlie's Golden Mile. Most of the recent gold boom has been associated with low grade, open pit free-milling oxide deposits. Primary sulphides are commonly encountered at depth and in many cases are highly refractory. Different approaches to the problem of recovering go1d from these ores have been adopted subject to local conditions both technical and environmental. The least preferred option is the preparation of a gold- rich flotation concentrate which is shipped to a smelter. Roasting of flotation concentrates can be practised in certain remote locations where sulphur emissions are tolerated. Fine grinding of flotation concentrates followed by direct cyanidation is another popular approach although this often leads to fouling of carbon by flotation reagents in the adsorption section and high soluble gold losses.

Jan 1, 1989

By J. R. England, W. J. Taylor

The Sudbury Basin is the scene of the mining operations of the Ontario Division of the International Nickel Company of Canada, Limited. Around the rim of the geological formation and within thirty miles of the City of Sudbury are located twelve operating mines and one open pit operated by the Company. The City, with a metropolitan population of some 100,000 lies 240 miles Northwest of Toronto. In addition, there is one mine in Northwestern Ontario, at Shebandowan, 700 miles Northwest of Sudbury. In 1973 these mines produced 16.5 million short tons of ore of which 14.9 million tons were from underground and the balance from open pit operations. Mining methods include blasthole, sublevel caving, induced caving, shrinkage, cut-and-fill and undercut-and-fill. Raise boring commenced at Inco in 1964 and is now applied at all mines in the Sudbury District (Figure 1). [ ]

Jan 1, 1974

By Graeme J. Jameson

A form of column flotation cell is described in which the contact between the feed and the air stream is made in a mixing device at the top of a vertical downcomer. The air-liquid mixture flows downward to discharge into a shallow pool of pulp in the bottom of a short cylindrical column. The bubbles disengage and rise to the top of the column to overflow into a concentrate launder, while the tails are discharged from the bottom of the vessel. The main advantages of the device described are that the overall height of the column is reduced to about one metre (3 ft), and the column can be self-inducing with respect to the air supply. Experimental results are given from tests on a feed stream to a conventional zinc cleaner circuit. Using wash-water to reduce gangue entrainment, the column gave high concentrate grades and high recoveries.

Jan 1, 1988

A form of column flotation cell is described in which the contact between the feed and the air stream is made in a mixing device at the top of a vertical downcomer. The air-liquid mixture flows downward to discharge into a shallow pool of pulp in the bottom of a short cylindrical column. The bubbles disengage and rise to the top of the column to overflow into a concentrate launder, while the tails are discharged from the bottom of the vessel. The main advantages of the device described are that the overall height of the column is reduced to about 1 m (3 ft), and the column can be self-inducing with respect to the air supply. Experimental results are given from tests on a feed stream to a conventional zinc cleaner circuit. Using wash water to reduce gangue entrainment, the column gave high concentrate grades and high recoveries.

Jan 1, 1987

By Slobodan Vujic

Production of building materials such as are stones, sand, gravel etc., is characterized by a relatively low economic value and requires reasonable transport costs. That is why we are often faced, in our practical work, with the fact that within the framework of a relatively small area several open pits of building materials are, developed side by side while neither ecological, urban and spatial nor location factors have been taken into consideration. Numerous locations together with heterogeneous factors. point undoubtedly to the problem of planning the open pits locations for building mateials as a very serious and complex one. Even when certain localities are in question, it is rather a difficult task to present a real state and encompass all the, important location factors by mathematical model ling. This paper presents one of such models for solving the problem of selecting a location for building materials open pit.

Jan 1, 1992

By Gary S. Brierley, Ronald E. Romley, Alan L. Howard

The Price Road Drain Tunnel in Tempe, Arizona is part of the drainage system constructed in conjunction with the Outer Loop Highway in metropolitan Phoenix. The Outer Loop Project is a part of a much larger expressway system that includes other large drainage tunnels such as the Papago Freeway Drain Tunnels. Large diameter downhole inspection borings were utilized to obtain subsurface data for the design of these tunnels. Subsurface data obtained from the large diameter borings resulted in the development of empirical parameters that were successfully incorporated into the Geotechnical Design Summary Report and which satisfactorily predicted ground behavior, formed the basis for improved geotechnical design criteria, and facilitated the cost effective assessment of third party risk. The purpose of this paper is to describe the subsurface exploration program performed for this project and to explain the methods used to evaluate underground construction procedures.

Jan 1, 1991

By Zhu Mingshan, Wu Jiang, Xu Yingqin

A mathematical model to simulate spontaneous combustion of coal in goaf was developed. Under the condition of two-dimensional flaw of air through a bed of uniform mixture of coal, gob, stone etc., the model simulates the temperature rise in the air-and-particle system associated with Arrhenius particle surface reaction. The model is developed as a set of coupled non-linear partial differential equations, which include (1)mass conservation equation for oxygen, (2)energy conservation equation for gas, (3)energy conservation for solid, and (4)velocity equation for gas, that are solved numerically. An elaborate parametric analysis is made of effect of leakage air flux and position of source and sink, parameters relating to the coal accumulating character and the kinetic properties of coal on the tendency to spontaneously combust. In addition, the dynamic process of temperature rise within goaf under several conditions is displayed with picture drawn by computer.

Jan 1, 1991

By Keith G. Wallace, Malcolm J. McPherson

In order to model accurately a mine ventilation system in an existing mine, it is necessary to determine the resistance to airflow in all main airways. This is accomplished by measuring the airflow and pressure differential in each airway. Gauge and tube methods have been used to determine pressure drops in ramps and level airways. However, it has rarely been used in evaluating the frictional pressure drop in shafts. Because shafts commonly have the highest pressure loss in mines, it is critical that the resistance of these airways be determined accurately. This paper describes the theory and practice of using the gauge and tube method for determining the pressure drop in shafts. The pros and cons of using this method are discussed as well as a comparison between the gauge and tube and barometer measurement techniques. Case studies showing the accuracy of shaft gauge and tube measurements are also presented.

Jan 1, 1991

By D. R. East

Recent experiences within certain sectors of the international mining industry suggest an underestimation of the environmental risks associated with the design of mine waste-management facilities. These experiences show that the technical and managerial challenges of responsible mine waste management is not always fully appreciated. Unfortunately, the image of the mining industry's environmental performance is negatively impacted by a relatively few number of failures. This negative view overrides the many positive contributions made by the majority of mining companies. The fact that these failures continue to occur in developed and developing countries is indeed re¬markable and indicates a degree of risk-taking approaching unacceptable levels. The design requirements for tailings storage facilities are, in many cases, more demanding than those of conventional water dams because seepage of fluids that contain dissolved metals may pose a greater threat than the mere loss of water.

Jan 1, 2000

By Harry Verakis

Electronic detonator systems are an advance in technology beyond conventional electric detonators for initiating explosives and blasting agents. Their use is widening into the mining operations of the U.S.A. Each electronic detonator system differs in design, construction, operation, and testing features and each system is different than “conventional” electric detonators. There are benefits of electronic detonator systems which serve to improve blasting safety. With the introduction of electronic detonator systems for mine blasting, issues were raised about the application of MSHA regulations for shunting and circuit testing. The MSHA regulations for surface and underground mine blasting operations address the use of “electric” detonators. Although electronic detonators are initiated by an electric pulse or current, their design is unlike “electric” detonators. To resolve the issues of shunting and circuit testing with respect to MSHA regulations, a technical and field evaluation of electronic detonators was made and the results are presented.

Jan 1, 2005

By G. Balletto

Increasing environmental awareness leads to a reflection on the consequences of a non-appropriate use of mining resources. In this sense the determination of the mining requirements for the building industry is the necessary prerequisite to activate planning in mining according to the principles of environmental sustainability. Experience shows that there is a relationship between the production of buildings in relation to the shape of the city and the resulting demand for minerals. The increasingly urgent demand for maintenance and restructuring by existing buildings will stretch further the demand for minerals with an excessive, no longer sustainable withdrawal, which will lead to focussing greater attention on environmental policies oriented to the use of alternative materials including materials from recycling. It is pointed out moreover that the joint action of land use planning and mining planning leads to interesting applications that have significant repercussions on the environment.

Jan 1, 2005

By Peter T. Luckie, Mark S. Klima

INTRODUCTION A physical separation partitions a stream of particles into two streams - one containing a concentration of a desirable constituent; the other containing a defficiency - on the basis of a difference in physical properties. Separating ores into concentrates of increased grade and gangue minerals has been practiced for thousands of years. Physical properties of materials which have been used to achieve separations include size, relative density, shape, magnetism, surface charge, color, characteristic emission, resilience and strength. The study of physical separations has also been termed attribute tracking. The term attribute is used to describe the content of the material of interest, or, sometimes, properties not used as a basis of the separation. The content is usually given by its assay; e.g., %Cu, %Fe, etc. Attribute tracking involves material balancing. For a separation using two physical properties, say x and y, the balance is

Jan 1, 1986

By Robert M. St. Louis, Janet M. Edgecombe

The Mercur Mine's autoclave is an alkaline pressure oxidation system, operating at 220°(428°F) and 3061 kPa (444 psig) (total). Up to 725 metric tons (800 st) of ore, grading 2.02 g per mt (0.059 oz/st) Au and containing 1 to 2% sulfide sulfur, are treated daily in this circuit. A mineralogical and chemical investigation was initiated to locate the cause of lower than anticipated gold recoveries. Greater than 70 wt. % of reduced sulfur is oxidized; therefore, the autoclave is operating at specification. The low recoveries were attributed to increased concentrations of organic carbon in refractory ore. Activated carbon concentration in the attached CIL circuit was increased from 15 to 40 g per 1, leach temperature held below 21°C (70°F), and carbon flow changed to counterflow. These measures resulted in gold recovery improving from 75 to 82%.

Jan 1, 1990

By P. Venkatraman, F. S. Knoll, W. S. Kow

Froth flotation is the most widely used technique for cleaning fine coal. This practice may change, however, with the development of enhanced gravity concentrators such as the Mozley Multi- Gravity Separator (MGS). The MGS is a flowing-film concentrator that utilizes centrifugal forces to improve the separation of flotation-size particles. In the present work, a pilot-scale test program was conducted to examine the effects of feed rate, feed solids content, wash water flow rate and drum rotation speed on the performance of the MGS. The test results indicate that the MGS effectively rejects high-density minerals such as pyrite, while ultrafine ash-forming minerals are removed less efficiently. A major advantage of the MGS is that high separation efficiencies can be realized without additional grinding, flotation reagents or heavy media. This article describes the working principles of the MGS and presents data obtained from recent pilot-scale test work.

Jan 1, 1995