Search Documents

By Robert A. Blake

Introduction Sulfide copper, zinc and iron concentrates are recovered in the 5000 ton per day flotation plant operated by Cities Service Company at Copperhill, Tennessee. The heavy-sulphide ore is first ground to 50 pct. minus 200 mesh and a bulk concentrate floated. The bulk concentrate, over 60 pct. of the ore weight, is reground to 72 pct. minus 200 mesh and then treated in a selective flotation circuit to recover copper and zinc concentrates. The tailing of selective float is the iron sulphide material source for the manufacture of sulfuric acid and iron sinter. The valuable minerals in the ore are chalcopyrite, marmatitic sphalerite, pyrite, and pyrrhotite. A typical mineralogical analysis will be found in table 1. A typical material flowsheet will be found in figure 1. Shown in the flowsheet are a scavenger float on the bulk rougher tailing and a copper-talc separation unit. At times a lead-copper separation circuit has been run.

Jan 1, 1971

By R. J. Sweigard, C. T. Justice, T. Beckham, E. D. Thompson, T. C. Hopkins

Fine coal refuse is often pumped, as slurry, into surface impoundments as a means of permanent disposal. As the available volume is filled, the height of the embankments are frequently increased. Many times the additional embankment material is placed upon consolidated fine coal refuse. There has been some concern about the long-term effect of consolidation of this material at or above the liquid limit upon its shear strength. A laboratory investigation was performed using three different types of fine coal sluny taken from Central Appalachian coal preparation plants. The refuse was consolidated in 10-foot plexiglass columns under incremental amounts of surcharge loading. The incremental loads were designed to simulate the effect of increasing the height of a refuse embankment on top of the consolidating coal slurry. After the refuse in the columns had consolidated for several months, the columns were cut apart and triaxial tests were performed on both the consolidated material and unconsolidated material for comparison of their shear strength parameters.

Feb 24, 1997

By K. Oraee

The empirical rock failure criteria play an important role in predicting the mechanical behavior of rocks, since affecting parameters on the behavioral properties of rocks are complex and numerous. Usually the empirical failure criteria are obtained by statistical methods, namely by means of fitting the mathematical function onto the experimental data. For evaluation and verification of the results, however, the quality and accuracy of the fit must be considered. This paper studies the efficiency and accuracy of conventional empirical rock failure criteria using a new approach, which is based on the analysis of uncertainty amplitude on the constant parameters of each criterion. The approach adopted here, is based on the combination of some parameters such as Mean Squared Error (MSE), Root Mean Squared Error (RMSE), type of function, degree of freedom and the confidence level of constants. Correlation coefficient (R2) is then a comprehensive test and can be used effectively for comparison and accuracy of empirical rock failure criteria.

Jan 1, 2012

By Burke Trafton

An earlier paper1 introduced a rapid solution for mine ventilation network problems, employing the digital computer. In this paper, refinements and additions to the computer program which expand its scope of application and a solution to a ventilation network having a coal-mine configuration are presented. Specifically, the revised program--written in FORTRAN for the IBM 7074 computer in Penn State's Computation Center--is applicable to any mine ventilation network employing natural splitting and having its fan located externally. It accomplishes the following; 1. Distributes an assumed total quantity of air flow among all air- ways of the network, performing iterations until an acceptable level of error is attained and the flow in each airway is known. 2, Computes the pressure drop (head loss) in all airways and the overall network and mine head losses. 3. Determines the operating point for the mine and a given fan, adjusting all air flows and head losses to the actual values.

Jan 1, 1964

By A. D. Davis

Limestone-based technology for arsenic removal from water is an innovative and promising method. The technology offers the potential for low-cost disposal of a stable waste product after arsenic removal, either in an ordinary landfill or by encapsulation in concrete. Leaching research described in this paper shows that the limestone waste, after encapsulation in concrete, passes the Toxicity Characteristic Leaching Procedure (TCLP) test. Leaching was less than 0.05 mg/L, which is 1/100 of the U.S. EPA?s standard for disposal of arsenic in a landfill. Disposal of arsenic-enriched waste is critical for commercial viability of arsenic-removal technologies. Low-cost disposal gives the limestone-based method an advantage that could help communities meet the new maximum contaminant level of 10 parts per billion for arsenic in drinking water. The ability to recycle the waste material in concrete could add a significant economic benefit, further reducing overall costs.

Jan 1, 2009

The MINER Act of 2006 mandated that all underground coal mines must install and maintain refuge chambers. Refuge chambers serve as a temporary shelter in case of emergency. Several factors affect the performance of a refuge chamber: heat production inside the chamber and introduction of CO when chamber doors are opened are two major factors. This study examines the CO purging process and to determine total air quantity and time necessary to lower the CO con-centration to safe levels for different inlet/outlet configurations using three-dimensional simulation technique. The study uses Reynolds Averaged Navier Stokes and continuity equations along with the spe-cies transport model assuming uniform air mixing. The heat transfer of any kind is neglected and the purging process is assumed to take place isothermally. The standard k-e model is utilized for simulating turbulence in the flow field. This research provides useful guidelines in developing an efficient strategy for purging refuge chamber. Keywords: Airlock chamber, Purging, Carbon monoxide, Turbulence

Feb 27, 2013

By Z. Yu

Low-rank/oxidized coals respond poorly to oil agglomeration. Emulsification of kerosene in the presence of surfactants dramatically reduces the size of the kerosene droplets. While this dramatically reduces the amount of oil that is required for efficient agglomeration (down to 0.25-0.5%), more importantly, the surfactants entirely change the electrokinetic properties of the oil droplets and thus the interaction between oil droplets and coal particles. Consequently, kerosene cationic emulsions can efficiently agglomerate oxidized coal particles. The agglomerates obtained in such a process can still be recovered by screening. Surfactants can affect fine coal filtration very profoundly when used to emulsify the oil which is utilized to agglomerate coal prior to its filtration. This sequence is much more logical than the use of flocculants - highly hydrophilic polymers - as filtration additives to aid dewatering of flotation concentrates. Although such polymers flocculate coal particles, they also render coal surfaces hydrophilic and make reduction of the cake moisture content difficult.

Jan 1, 2000

By F. Habashi

Brazil is a major mineral and metal producer, has magnificent fauna and flora, and superb architecture. In 1693 gold was discovered in Ouro Preto and Brazil produced about half of the world's gold. In 1726 diamond was discovered in the region of Tijuco in the Province of Minas Gerais, 150 km east of Bello Horizonte. The country became independence from Portugal in 1822 as the Brazilian Empire. In 1876, an Englishman succeeded in obtaining from the Amazon region seeds of rubber trees and secretly transferred them to England, where they were planted in the royal gardens at Kew. Some of the seedlings which spouted were sent to Ceylon and Singapore. Thus, began the rubber industry in the East. Today, Brazil is the largest producer of niobium, and produces a large number of other metals. The Mineral Research Center in Rio de Janeiro is the countries main Government establishment for mineral research. The country has been a republic since 1889 with its capital in Brazilia.

Jan 1, 2009

By William W. Shriver

When the Henderson Project is completed in 1975, it will become one of the Free World's largest primary molybdenum producers. The Henderson Mine will be located approximately 50 miles west of Denver, Colorado, on the eastern slope of the Continental Divide. Ore reserves are currently estimated to be 303,000,000 tons with a grade of 0.49% MoS2. The mill and tailing area will be located approximately 14.5 miles from the mine in the Williams Fork Valley, which is on the western slope of the Continental Divide. Ore haulage from the mine to the mill will be by ten miles of underground railroad and 4.5 miles of surface railroad. The concentrator has been designed to mill 30,000 tons per day and will yield approximately 50,000,000 pounds of contained molybdenum per year. This paper is concerned with the tailing and water supply system for the Henderson Project and in particular the environmental considerations affecting their design.

Jan 1, 1970

By J. Schenck

Goldcorp Inc. has mining operations and exploration projects throughout Canada, the United States, Mexico, Guatemala and Honduras; as well as partnerships in Argentina and the Dominican Republic. In rural areas of developing countries it is very common to have mining operations surrounded by diverse communities consisting of people with limited, or no formal education. This is fertile ground for anti-mining NGOs to cultivate. The limited educational backgrounds of the people, coupled with a company desire to maintain a low profile can lead to a problematic lack of trust between the local communities and the mining company. As part of its commitment to environmental stewardship and sustainable development, Goldcorp has implemented various programs to build trust at these operations, as well as incorporating this policy into any new projects prior to commencement of operations. This paper is intended to describe two initiatives that have shown positive results for both the communities and the Marlin Mine.

Jan 1, 2009

By Gail I. Bakker, Mark E. Smith, George Sintay, Allan Young

The Snow Caps mine was an open pit and conventional cyanide heap leach gold project located 10 Km east of Independence, California in the Owens Valley. The project is unique in that it is one of the first projects to go full-cycle, from design through closure, under California's Chapter 15 mine waste regulations adopted in 1984. The property was acquired by Sunshine Mining Company in 1985. During 1986, final design and permitting were completed and the facility was commissioned in 1987. Mining continued to mid - 1990, when the minable ore body was depleted, and heap leaching continued into early 1991. Rinsing of the spent ore was completed in 1991, and final closure will be complete in 1992. The spent ore will be left on the leach pad for its final disposition. The focus of this paper is the permitting and closure aspects of the project as required by California's Chapter 15, Article 7 regulations.

Jan 1, 1992

By Gary A. Perry

Cyprus Sierrita produces copper and molybdenum from its Sierrita and Twin Buttes open pit mines south of Tucson, AZ. Both pits were started in the late 1960s and are more than 460 m (1500 ft) deep. Sierrita has used a Caterpillar 992C Remote Controlled Loader since January 1993. The loader was justified to increase safety and profits at Sierrita. It has exceeded all expectations. As of June 1993, the 992C had produced additional profits of more than $1.5 million. Safety and Geotechnical The safety of Cyprus personnel and equipment is always of prime concern. The remote controlled loader removes personnel from the active raveling area. But it requires prudent operation. The remote controlled loader discussed here is always intended to be used in a safe manner under a managed slope. Any increase in slope angle or use of any equipment under a critical slope is taken only after careful analysis of the specific

Jan 1, 1994

By Alex Ruzycki

Gold Fields-Mesquite is a 7.5 million ton per year heap leach operation located in the Maj ave Desert of Southeastern California. Extraction of gold is carried out on multiple lifts, with over 33.3 million tons of ore leached since the inception of operations in 1985. The delineation of the gold left in heap residue is a formidable task. Gold removed from active leach areas can be routinely monitored through sampling of emerging solutions but exact recoveries from specific heaps remains nebulous due to factors such as cross flow between sections buffering effects from multiple lifts, and releaching. In order to better quantify ultimate heap recoveries and increase releach efficiency, Mesquite initiated a residue drilling program. The project progressed through an evaluation of sampling protocol, drilling of residue by reverse circulation, entry of assays into a software package capable of producing grade-based contour maps, and a production scale releach test that evaluated the system's ability to predict residue grade.

Jan 1, 1992

By Z. Kowalski

Landfilling of waste causes the degradation of natural environment, not only due to land occupation, but also due to pollution of air, water and soil. The flotation waste from zinc-lead industry also poses such problem. There is a need to find the way to utilise substantial amount of these wastes and backfilling seems to be a good solution. Recently, in Poland only sand was used for backfilling. However, it will be more beneficial to substitute the sand with the industrial solid waste, especially flotation waste. The tests were performed in the laboratory to examine the use of flotation waste as a main ingredient for backfilling. The use of flotation waste is possible only when it is combined with other waste with specific bonding properties, especially regarding the prevention of leakage. The outcome of tests shows that flotation waste combined with cement and fly ashes can be used as a backfilling material. This paper presents the preparation of flotation waste for using it for backfilling.

Jan 1, 2006

By A. Dan Rovig, C. Kevin McArthur

Technical and managerial innovations in the minerals industry have allowed continuing mining activities in the United States, and elsewhere, as gold orebody quality has diminished or has become more refractory. Of course, world markets, permitting requirements, and political processes also have created a need for innovative practices that contribute to the survival of the mineral industry. The gold industry has been transformed, during the past approximately 40 years, from a predominantly underground mining and milling type of exploitation and extraction to the large-scale, relatively low-grade type of extraction that is common in the United States today. Indeed, with the introduction of gold heap-leaching technology and the development of mines that produce from large, relatively low-grade gold orebodies in the western United States, a "new" industry was born and continues to prosper today. It is worthwhile noting, however, that Dobra (1997) has reported that one of the major trends in the North American gold industry is a movement back toward underground developments.

Jan 1, 1998

By M. Cambridge

The extractive industries are currently, and will continue to be, major contributors to the world economy, particularly in the developing world where economic growth is dependent upon a sound supply of primary materials. However, tailings dam and other mine failures have been very much a feature of recent anti-mining publicity, particularly in Europe, and thus instrumental in inhibiting new mine developments. Although, superficially, the record of dangerous incidents might support the anti-mining position, closer inspection suggests otherwise. This paper reviews the failures which have occurred over the last 50 years and demonstrates that, though poor practice is an ongoing problem for the industry, the record is one of improvement in both design and practice. Examples are provided of significant events which have led to dramatic advances in design and operation. The paper assesses the improvements made in technology and practice, and concludes that historic events must continue to form the underlying basis for design and operation of future mining projects.

Jan 1, 2005

By S. K. Kawatra, S. J. Ripke

Finely disseminated iron ores compose much of today's reserves. After removing the silicate gangue, the resulting fine iron oxide concentrates require pelletization with a binder to enable transportation and reduction. Binders can be used more efficiently if their binding mechanisms can be completely understood. Typically, bentonite clay is needed as a binder to improve the strength of the pellets. Bentonite is an effective binder at a relatively low cost, but costs could be reduced further by replacing bentonite with even lower-cost binders, such as high-carbon Fly-Ash Based Binder (FBB). In this study, it was found that bentonite binds by a physical mechanism, while FBB binds by a chemical mechanism. These mechanisms were determined to be incompatible. Partial replacement of either binder with the other reduced dry magnetite pellet compressive strengths below the industrially acceptable value of 22.2 newtons (5 lbf). Activators and accelerators that activated the fly-ash deactivated the bentonite. The incompatibility of these two binders is explained.

Jan 1, 2000

By N. Roqueñí, J. Loredo, F. Pendás

Impacts of mining on surface water and groundwater occur frequently not only in active mines but in abandoned mines, then the establishment of effective legal mechanisms for the regulation and control of mine waters is a necessary step in order to avoid pollution from mine waters and in consequence to contribute for a sustainable development of the mining industry. Currently there is a lack of a specific European legislation about mine waters and this absence of legislation occurs too at national level in many European countries. This absence of an European specific regulatory framework for mine water pollution questions the effectiveness and the applicability of the current legislation and this fact has led the EC to put forward proposals legislation to adequately deal with environmental and social consequences of mining, and among those proposals is a draft for a directive on waste from the extractive industry that includes provisions for mine water pollution.

Jan 1, 2005

By S. L. Bessinger

The need for improved safety and productivity brought about the introduction of longwall mining to the Appalachian coal fields. These same forces continue to drive developments in modern longwall equipment and mining practices. Current initiatives to improve productivity and safety are focused on automation and the effects of scale in equipment design. Longwall roof-supports, shearers and face-conveyors have changed significantly. Panel layouts have evolved to include larger total tonnages and provide for more rapid development of gate-entries. These advancements have improved longwall productivity and new production records are continually being set. Roof supports Reliability is implicit in the quest for automation. It is impossible to automate equipment if it is not reliable. To a large degree, this has been the problem with longwall shield automation efforts. The "electronic control" of shields depends on the proper functioning of electronic equipment, electrohydraulic valves and full-flow service valves onboard every support.

Jan 1, 1995

By Richard L. Bullock

The hard rock mining industry has long envied its counterparts in underground mining of evaporites, coal and soft iron ore, who have made great strides in productivity using mechanical excavators. Continuous mining machines produce large tonnages in Canadian potash mines and in modern longwall coal mines. Hard rock is defined here as having an unconfined compressive strength (UCS) of more than 124 MPa (18,000 psi). Silica content, rock quality designation (RQD) and fractures affect the ability of mechanical tools to excavate rock, but the UCS is the main factor. Much research and development work has been devoted to continuous mechanical mining of hard rock, and the technology continues to improve. A few commercial applications have been reported. The development process has been slow and costly, but the outlook for the technology has never been more promising. The current state-of-the-art of continuous, mechanized underground mining technology is reviewed here, with examples of commercial applications that have been tried in recent years.

Jan 1, 1994