Search Documents

By Donald A. Dahlstrom

INTRODUCTION Solid-liquid separation is an important and many times a critical step (or steps) in a mineral or coal processing plant. Some examples of typical critical separations are as follows: 1. Operating a seven to eight stage CCD thickening circuit to re¬cover almost all of the caustic and alumina trihydrate values in an alumina plant. This must be accomplished with highly scaling slurries, starting temperatures of over 100°C and operate on a closed circuit system. 2. Making a filter step operate to produce a proper moisture for the balling step so that the pellet furnace can produce a proper product. Bentonite addition must be minimized and a good quality filtrate must be maintained to prevent abrasion of the internal parts of the filter. 3. Operating a closed water system in a coal washing plant so that reclaimed water containing less than one percent suspended solids is produced for reuse to maintain beneficiation ef¬ficiency. Refuse solids must also be thickened so that they can be effectively dewatered to meet state disposal requirements. 4. Recovering phosphoric acid values from a slurry containing gypsum and other gangue solids at an elevated temperature. This must be done while minimizing wash water and maximizing P2O5 re¬covery while simultaneously minimizing scale problems. While solid-liquid separations are important to overall performance in the processing plant flowsheet, it is also a significant factor in plant costs. Capital and operating costs for all the solid-liquid separation steps (includ¬ing water reclamation for reuse) in such plants are probably between 10 and 20%. Energy consumption can also be important in these separations. For example, in the copper concentrator, it is the third largest category in energy consumption, after comminution and flotation. Obviously, solid-liquid separation steps in a plant demand proper atten¬tion in design in order to achieve both optimum performance and cost. Simultaneously, knowledge of funda¬mentals are important to improve results in existing plants.

Jan 1, 1986

By M. Imazu, Ö. Aydan

"A new rock classification, Rock Mass Quality Rating (RMQR) proposed by the authors is briefly explained and its application for the design of tunnels and large underground openings support systems is described in this paper. RMQR is an index to evaluate the state of rock mass. The preliminary support design may be based on the concept to prevent structurally controlled failures of rock mass. RMQR can also evaluate the yielding characteristics of rock masses so that it is possible to design a support system to prevent or control the deformation of surrounding rock through the utilization of the proposed rock mass classification and some analytical and numerical techniques.INTRODUCTIONThe first three authors proposed a new rock classification system named Rock Mass Quality Rating (RMQR) (Aydan et al. 2014). RMQR quantifies the rock mass state, and using the classification system together with intrinsic geo-mechanical properties of intact rock, possible geo-mechanical properties of rock masses can be estimated. The instability modes of underground openings can be structurally controlled because of the orientation of discontinuities in rock mass and the in-situ stress induced (Aydan 1989; Aydan et al. 1993, 1996; Aydan and Genis, 2010). The authors (Aydan and Ulusay, 2013; Aydan, 2016) have also tried to apply this system to the design of a tunnel support system. The authors presented initial guidelines for the RMQR classification system earlier (Aydan and Ulusay, 2013).In this paper, the authors provide further guidelines and establish some criteria for support system design that considers loading conditions and types of underground structure according to RMQR. Guidelines are alsos proposed for selecting the proper size of rockbolts, rock anchors, shotcrete, steel ribs and concrete liner. These guidelines are based on past experiences with various underground structures, theoretical understanding and the anticipated behavior of rock mass under given in-situ stress conditions and excavation techniques. The authors also utilized some databases developed for large underground caverns and tunnels excavated in squeezing or rock-bursting ground conditions."

Jan 1, 2016

By Thomas E. McNider, Robert C. Howell, J. W. Stevenson

As of the end of October, 1990, there have been eight spontaneous combustion heatings reported to the Mine Safety and Health Administration (MSHA) at the No. 5 Mine. A reportable heating is defined as one with elevated surface temperatures of the strata greater than ll°C (20°F) above the ambient. The first heatings occurred in November, 1986. The last three heatings were located near the start line of "K" Longwall Panel in the southwest where mining had begun on May 21, 1990. All of the heated areas had been at the time of detection, or were sometime areas of high ventilation pressure differentials or high air velocities. All of the heated areas are in an expanded seam with associated, extensive floor heave which is characteristic of all of the expanded seam thus far exposed by development mining in the No. 5 Mine. Jim Walter Resources, Inc. submitted a plan to MSHA which would reduce the potential for spontaneous combustion at the No. 5 Mine by reducing high air velocities and high pressure differentials in the gob. These two parameters are the dynamics which feed oxygen to the pyrite, thus initiating the oxidation process which can lead to spontaneous combustion. No. 5 Nine operated under this plan for 29 shifts before mining on the longwall was stopped by MSHA and the Spontaneous Combustion Control Plan revoked. This paper briefly details the geology of the expanded seam and history of the heatings. It also gives a retrospective view of the operation under the Spontaneous Combustion Control Plan and reasons why it was revoked by MSHA. Currently, knowledge of the reaction process of the footwall coal seams at No. 5 Mine and other potential spontaneous combustion seams in the United States is limited. There are techniques used in the United States and other countries to minimize the potential for heatings in spontaneous combustion prone areas. The No. 5 Mine has attempted to utilize this current technology. However, in deep, gassy mines the problem is complex.

Jan 1, 1991

By John W. Wilson

Every operation connected with the working of a deep-level mine has, to a greater or lesser extent, a direct bearing on the costs of production, and hence, profitability of the mine. If adequate mine planning is not done in the early stages in the life of a mine, considerable expenditure can result from the cost of maintaining mine service tunnels, production delays in stopes caused by poor strata control, distortion of fittings in hoisting shafts, rockbursts and so on. In fact, the optimum profitability of a deep-level, hard-rock mine can only be achieved if the layout of the shaft systems, ore passes, tunnels, stoping areas and other underground excavations are designed to withstand or accommodate the rock stress conditions that will be created by mining operations. In South Africa where the deepest mines in the world are located, access to the underground workings of most deep-level gold mines is via vertical shaft systems and a network of tunnels connecting the shaft systems to the stoping areas. In current practice, there are two basic methods of extracting the gold-bearing reef,* namely, the scattered stoping method and the longwall stoping method. The choice of the stoping method is governed largely by the anticipated gold distribution and payability of the reef in the area, the geological conditions, the degree and complexity of faulting and dyke intrusions, the depth at which the gold-bearing reef is to be mined and the inclination and width of the reef. The longwall system was first introduced at the East 717 Rand Proprietary Mines Limited in 1942 in an effort to combat the rockburst hazard which appeared to increase with increase in depth. This mining method became standard practice on that mine for stoping operations 700 ft. below the surface. Since that date, several deep mines on the Central Rand, East Rand and West Wits gold mining areas have adopted this method.

Jan 1, 1977

By Thomas E. Garnar

Zirconium and hafnium are the twin elements of the periodic table because they are always found together. They resemble each other so closely that hafnium was not discovered until 135 years after the discovery of zirconium. Zirconium was discovered by Klaproth in 1789 and isolated 35 years later by Berzelius. Because hafnium's chemical properties are so close to those of zirconium, it was not discovered until 1923 when Coster and von Hevesy detected it using X-ray spectrographic analysis. These elements occur most commonly in nature as the mineral zircon (ZrSiO,) and less commonly as baddeleyite (ZrO,). They also are found as a variety of other silicates. Zircon was identified as a component in alluvial and beach sands in 1895, but it was not produced in any quantity until 20 years later. During World War I, it was produced as a coproduct of beach sand mining for titanium minerals just south of Jacksonville Beach, FL, and was patented as a refractory. It was not until the 1930s, when Zircon Rutile, Ltd., began mining at Byron Bay on the east coast of Australia, that zircon was first used as foundry sand. Later in the 1940s, NL Industries and Humphreys Gold Corp. began production of zircon sands from fossil beaches in northeast Florida. Baddeleyite first became available as a commercial product in 1916, but never in the quantity of zircon. Zircon holds a unique position as an industrial mineral because it is used for both its physical and chemical properties and as an ore of zirconium and hafnium metals. Australia is the major zircon producer followed by the Republic of South Africa and the United States. Zircon is also produced in India, Sierra Leone, Sri Lanka, Malaysia, the former USSR, China, Thailand, and Brazil. The location of world zircon mines, baddeleyite mines, and undeveloped zircon ores are shown in [Fig. 1]. World production of zirconium mineral concentrates is shown in [Table 1].

Jan 1, 1994

By James R. Brown

Mount Isa Mine should be regarded as a large mining complex rather than one mine. This arises from the geography, variety and extent of the orebodies, the mining methods, and the use of 14 shafts for ventilation distribution. A brief resume is presented here since comprehensive descriptions of lead-zinc mining methods {11}, copper mining methods {2 }{3}, geology 241, stope fill {5} and ventilation techniques {6}{7}, have all been published in the last five years. Mining extends over a north-south strike length of 2.5 miles (4 Ian) with a maximum width across dip approaching 3 200 ft (1 Ian). Current mining is to a depth of 3 150 ft (960 m) with the ore hoisting shafts extending 660 ft (200 m) deeper. The composite longitudinal section, Figure 1, shows a representational disposition of the copper and lead-zinc-silver orebodies in the central shaft complex where the main service and hoisting shafts are located. To the south the X41 man and materials shaft provides access to the copper area. The mine layout is typical of high tonnage track- less mines, utilising a large diesel fleet, raise- borers and some large diameter hole stope drilling. Mining methods include sublevel open stoping, slot and massfire, and a trial vertical crater retreat in the copper ore, and sublevel caving, sublevel open stopes with and without rib pillar recovery, and mechanised cut and fill in the numerous lead orebodies. All ore reports to one of the three crushing systems located below 19 level in the central shaft complex. Copper ore is hauled exclusively along the 19 level computer assisted Rockflo haulage system, and lead-zinc-silver ores report via central orepasses from Granby haulages on 13 level and 15 level. Tonnages hoisted during the 1977178 financial year were 5.0 million for copper at 3.2%. and 2.3 million for lead-zinc-silver at 7.8%. 6.3% and 7.06 oz/ton (216 g/tonne) respectively.

Jan 1, 1980

By Edoardo Misano, Magali Schivre, Martino Semeraro, Alain Bochon

"INTRODUCTIONThe Laboratoire Souterrain de Modane (LSM) is an underground research laboratory located in the Western Alps on the French – Italian border. It is located in the middle of the 13km long Fréjus highway tunnel that links Modane (France) to Bardonecchia (Italy) in correspondence of the highest overburden of 1800m. The LSM current activity is mainly based on the investigations about the dark matter and requires very sensitive instrumentation which shall be protected from cosmic rays. To comply with the new legislation about safety in tunnels, the highway tunnels owners agreed in 2007 the construction of a parallel safety tunnel, at an average distance of 50m from the existing tunnel and the laboratory owner CNRS (Centre National de recherche scientifique) also decided to extend the existing laboratory with the construction of a new 17000 m3 cavern allowing the installation of wider and more powerful instruments that could increase chances of success of research. Preliminary studies stated that, considering both geological and functional issues, the most appropriate location for the new laboratory shall be in between the two tunnels and parallel to the existing laboratory (see Figure 1).Hence, the CNRS asked Systra, already in charge of the works supervision of the safety tunnel, to realize the design of the new cavern. The laboratory extension includes the construction of a 40 m long cavern with 300 m² cross section and two smaller tunnels connecting the safety tunnel and the existing laboratory to the new cavern. The minimum distance between the front face of the new LSM and the highway tunnel is about 25 m.The French and the Italian authorities, responsible of the exploitation of the Fréjus highway tunnel, asked the CNRS to develop an accurate study indicating that the construction of the laboratory extension would not have any negative impact on the existing structures of the highway tunnel. The main results of the developed study by Systra are summarized hereafter. The construction works should begin prior to the end of the construction works of the Fréjus safety tunnel in 2018."

Jan 1, 2016

By J. Schoenbacher

Park City Municipal Corporation (PCMC), long before being recognized as an Olympic venue was known as one of the great American silver mining towns. During a century of active mining, the Park City mining district produced millions of ounces of silver in addition to a substantial amount of mine tailing waste. Since 1985 the City has been remediating these impacts with state and federal oversight. One particular challenging CERCLIS site, that was previously a historic mine tailings pond is known as Prospector Square Development (CERCLIS Listing Silver Creek Tailings UTD98051404). This site has been very challenging due to the metals that impact the shallow ground water that eventually drain into the Silver Creek Watershed. To address the water quality impairment the City and Missouri University of Science and Technology teamed up to investigate the feasibility of constructing a horizontal-flow wetland to treat this pollutant source. This effort began with the building of a pilot cell in June of 2004 and lead to the construction of a full scale horizontal-flow wetland in the fall of 2008. The design of the pilot and full scale biocell was based upon lab-scale research conducted by the Missouri University of Science and Technology. In October of 2008, the Prospector Drain effluent was introduced to the system and to date analytical results reveal that the biocell is treating the Prospector Drain outfall below the Silver Creek Total Maximum Daily Load (TMDL) endpoint goals for zinc .39 mg/L and cadmium .00075 mg/L. The water chemistry of the influent, that originates from the historic silver mine tailings pond, is impaired with zinc and cadmium and has low iron with a pH of roughly 6.5. The construction of this unit encountered many challenges related to constituent relations, regulatory scrutiny, constructability and start-up. Nonetheless, since implementation this unit is considered a success for improving water quality within the Silver Creek Watershed.

Jan 1, 2011

By N. P. Titkov

This paper presents the results of laboratory and pilot plant investigations for the development of efficient methods of beneficiating hematite ores from the Krivoi Rog, Kursk Magnetic Anomoly, Olenogorsk, and other localities. The tests included gravity, magnetic (in a high intensity field), flota¬tion, and magnetizing roasting methods. It was possible to develop efficient beneficiation methods depending on the mineral composition of the ore and degree of dissemination of ore and gangue minerals. The paper shows the relationship between the iron silicate and quartz content of the ore and the technologic indices of the various beneficiation methods. Some of the conclusions based on these investigations and the technical and economic computations related to the cost of one ton of pig iron produced from concentrates obtained by the various beneficiation methods are: 1. If the hematite ore is not disseminated uniformly, it is expedient to use a combined gravity and flotation process. Ore particles up to 50 am. in size are beneficiated by gravity (heavy suspension, jigging, and others) and yield a lump concentrate. The middlings from this process are recrushed and floated; 2. Finely disseminated hematite ores, containing small quantities (less than 5 percent) of iron silicates, are most effectively beneficiated by flotation. Anionic (sulphate soap, tall oil emulsion with various foam depressors) as well as cationic collectors may be used. Depending on the mineral and chemical composition of the ore, it is possible to obtain concentrates containing up to 65 percent iron with an extraction up to 94 percent; 3. Finely disseminated, mixed hematite-magnetite ores may be beneficiated by flotation or a magnetic separation-flotation process; 4. Finely disseminated hematite ores, containing large quantities of iron silicates and earthy hematite ores are most efficiently beneficiated by the magnetizing roasting method. This method will yield concentrates containing up to 68 percent iron with extractions up to 90 percent. Although beneficiation by the magnetizing roasting process is costly, it will nonetheless, when employed on this type of ore, yield the least expensive pig iron.

Jan 1, 1960

As ore deposits become finer grained the requirements for regrinding before cleaning or leaching have increased substantially. Despite this increasing need, there is no standard test to predict grinding energy requirement below 70 microns. The standard Bond Mill test applies for coarser ball milling, but is not appropriate for stirred milling with fine media grinding to 70 microns. With no industry -standard test, the energy requirement is often made on the basis of supplier estimates or benchmarking against similar applications. Yet suppliers use vastly different scale-up methods which result in widely different energy estimates. Estimates can differ by 100-300% even for similar mills. This must result in serious errors to install either too much or too little grinding power. This paper explores this by comparing the actual performance of full scale regrind mills against their original design estimate. It confirms that serious scale-up errors have been made, and have then been perpetuated by ?benchmarking?. The test conditions to achieve accurate power estimation are discussed. The essential test conditions are: continuous (not batch) tests, ensure steady state (no coarse fraction retained in test mill), correctly account for classification, measure energy directly (not inferred), and using the same media size as the full scale installation. Failure to correctly address even one of these factors can bias results by 40%; failure to address several multiplies the error.

Jan 1, 2011

By Debbie Laney

DOUG HALBE: Second in our quick run-through on "Operating Ideas That Have Saved Me Some Bucks," was Debbie Laney of Rayrock Mines. Debbie apologizes. She can't be here. But she said, "Doug, don't worry. I've asked Mary Korpi to present the paper. We're both short, blond, and wear glasses. Nobody will know." [laughter] Mary, I caught it right away. You ladies can't fool us. Debbie, who wrote the paper, has spent almost her entire career in operations. She is currently metallurgical manager of Rayrock Mines in Valmy, Nevada. Mary Korpi is also a real operator (that doesn't sound right). She has been responsible for a number of operating areas at Newmont's Nevada operations, and she is currently taking a break from operations as manager of public relations/employee communications for Newmont Gold in Carlin. MARY KORPI: They told us this year at Newmont that we were going to have to work twice as hard. I had no idea it meant I would have to work for another company, too. Over the years, and many times in association with work for mid- to small-size mining companies, there have been two areas that seem to have been the focus of cost savings when looking at new facilities or new processes.

Jan 1, 1998

Beneath some of New York?s most iconic buildings ? The Met Life Building, the Helmsley Building, the Waldorf Astoria ? crews are busily at work on the Metropolitan Transportation Authority?s long-awaited East Side Access (ESA) project. In fact, it is 14 floors beneath the famed Grand Central Station where one of the centerpieces of the project, the new Long Island Railroad (LIRR) station terminal, is being blasted and carved into shape. When completed in 2016, the $7.3-billion ESA project will increase LIRR?s capacity into Manhattan and significantly relieve congestion at Penn Station. Currently, 37 LIRR trains per rush hour roll into the crowded Penn Station where many riders must then transfer to subway trains to complete their commute. When completed, the ESA tunnels will bring an estimated 160,000 riders directly to Grand Central Station, saving those riders 30 to 40 minutes. Studies have found that more people work within walking distance of Grand Central than Penn Station. ?The benefits of the project are tremendous,? MTA Capital Construction President Michael Horodniceanu told more than 340 industry professionals attending the UCA of SME?s George A. Fox Conference in New York on Jan. 26. ?The ESA is the first expansion of the LIRR in 100 years. It will increase the East River tunnel capacity by 50 percent and will help support job growth around Grand Central.?

Jan 3, 2010

By H. Verakis, M. J. Sapko

The Pittsburgh Research Laboratory (PRL)1 of the National Institute for Occupational Safety and Health (NIOSH) in collaboration with the Mine Safety and Health Administration (MSHA) Technical Support Center has devised a prototype hand-held instrument which can provide a direct assessment of the potential explosibility of a coal and rock dust mixture. Current Federal regulations require that rock dust be applied in all underground areas of a coal mine to mitigate the propagation of a coal dust explosion. To determine compliance with the Federal regulation, mine inspectors collect dust samples from sections of underground coal mines for an MSHA laboratory analysis of incombustible content. However, the laboratory analysis may not be completed for more than a week or two, during which time the mine area from which samples are taken may be inadequately protected. The operation of the Coal Dust Explosibility Meter (CDEM) is based on the difference in optical reflectance between light rock dust and dark coal dust. For a given coal volatility, the optical reflectance of such mixtures is relatively constant at the limit of explosibility, independent of the coal dust particle size. The CDEM is not intended to replace the current MSHA laboratory analysis of coal mine dust samples for incombustible content, but to serve as a supplemental device for enhancing mine safety through improved rock dusting practices.

Jan 1, 2006

By K. F. Bailey

Naturally occurring asbestos in aggregate and other mineral deposits, and the release of asbestos fibers into the ambient environment, is a public health concern. Determining the presence of asbestos in an ore body also presents a considerable sampling and analytical challenge. Improper and inaccurate identification of asbestos can result in unwarranted public and worker panic leading to significant costs to mine operators both in terms of dollars and company image. Some companies have been forced out of business simply because they had the non-asbestiform, prismatic variety of one of the six asbestos minerals. In the late 70’s, asbestos was found as a contaminate in a trap rock quarry in Rockville, Maryland. This discovery led to a massive overreaction by federal, state and local governments. In 1986, the Occupational Safety and Health Administration (OSHA) promulgated a final rule that regulated the common non-asbestiform mineral habits of actinolite, tremolite, and anthophyllite as if they were asbestos. The rule was reversed after a six-year struggle. Recently, the Libby, Montana, W. R. Grace vermiculite - asbestos, as well as the California chrysotile in serpentinite, and the New Jersey Southdown quarry – asbestos events have rekindled the entire issue of naturally occurring asbestos. It is time to get this concern addressed with sound science so that real asbestos is properly identified and controlled.

Jan 1, 2002

By D. Bradbury

Sufco coal mine, a subsidiary of Arch Western Bituminous Group, recently purchased a reverse osmosis (RO) system. The systems intent was to remove impurities in the water being mixed with the hydraulic oil to maintain the viability of critical longwall hydraulic systems and to prevent degradation. This project not only ensured hydraulic components from corrosion, but also revealed a cost savings by reducing the percentage of hydraulic oil mixed with the RO water. SUFCO WATER TREATMENT HISTORY Sufco coal mine has been in operation for approximately 70 years. Old works extend up to 15 miles one way, not including adjacent mined out longwall panels. Due to the geologic conditions and strata, water treatment has been as simple as putting water in at a high point of a mined out area and recovering it at a low point to discharge. Doing this reduces the total suspended solids (TSS) to less than 25 parts per million (ppm) and the total dissolved solids (TDS) less than 1,200 ppm which complies with Sufco?s water discharge permit. Even though the requirements for the permit were met, the water is still corrosive in nature. A portion of this water is piped back into the fireline (makeup) water system. It is then boosted to pressures of up to 500 psi to support mining sections, belt systems, equipment, fire fighting systems and the longwall.

Jan 1, 2011

By J. Evans

INTRODUCTION Section 209(b) of the Federal Land Policy And Management Act of 1976 (FLPMA-43 U.S.C. 1719 b) authorizes the Secretary of the Interior to convey mineral interests owned by the United States where the surface is or will be in non-Federal ownership. The objective is to allow consolidation of surface and subsurface (mineral) ownership. Certain major conditions must prevail for a conveyance to occur. These are: 1) There are no known mineral values (KMV) or 2) Where the mineral reservation interferes with or precludes appropriate non-mineral surface development and that non-mineral development is a more beneficial use of the land than the mineral development. Remember that allegation, hypothesis or speculation that the conditions could or may exist in the future will not be a sufficient basis for conveyance. Convincing factual evidence for an applicant’s case for mineral conveyance must be made in order to achieve that conveyance. See 43 CFR 2720 0-1 to 0-3, and 0-6. CONCEPT OF KNOWN MINERAL VALUES Known mineral values means mineral rights in lands containing geologic formations that are valuable in the monetary sense for exploring, developing, or producing natural mineral deposits. The presence of such mineral deposits with potential for mineral development may be known because of previous exploration, or may be inferred based on geologic information (43-CFR 2720.0-5(b).

Jan 1, 2007

By S. K. Kawatra, T. C. Eisele

Coal-cleaning operations commonly produce a fine-waste stream containing a considerable amount of coal. The recovery of this coal is normally not economical because the coal is mixed with large amounts of difficult-to remove clay slimes and is often heavily oxidized or contaminated. Conventional froth-flotation machines cannot, in a single flotation stage, produce an acceptable product from such material, and even flotation columns often have difficulty cleaning this type of feed. A new type of flotation column was designed specifically to deal with these problems, and a column of this design was installed and tested in a coal-cleaning plant in Ohio. The feed coal tested was the plant&apos;s tailings-thickener product. The coal was 80% -176 µm and had a heating value of 8401 Btu/ lb. The coal contained 39.8% ash, as fine clay, and 2.83% total sulfur. Because previous attempts at conventional flotation of this type of material had been abandoned, plant personnel believed that the coal was too heavily oxidized and contaminated for flotation to be effective. However, by using the new column it was possible to recover up to 85% of the calorific value in a product containing < 11 % ash, and it was possible to recover 60% of the calorific value in a product containing <8% ash. In addition, the bulk of the pyritic sulfur was also rejected from the coat.

Jan 1, 1996

By Jair Carlos Koppe, João Felipe C. L. Costa, Luis Eduardo de Souza

United Nations (UN) has been leading an international committee to define the guidelines in reporting resources and reserves. The system proposed by UN is very similar to the guidelines currently in use in Australia known as JORC guidelines (Joint Organisation Reserves Committee). The JORC guidelines show major differences in relation to the Brazilian system current in practice. The important aspects differing JORC from the current Brazilian guidelines for reporting reserves is the required sampling spacing. The JORC system requires the points of observation to be closer spaced than the Brazilian system for any class of resources. All classification systems share some common aspects in terms of defining the classes of resources based on distance separating samples and on the degree of confidence or accuracy associated with the results reported. Despite of being very clear in terms of stating sample distances, all the systems of classification do not provide clear definitions on how confidence limits should be calculated. This paper proposes a geostatistical framework to measure the uncertainty associated with the reported tonnages and grades. Results demonstrate that the error associated with an estimate can be approximated using multiple simulated deposits to define confidence limits. The methodology is illustrated in a large Brazilian coal deposit and proved to be appropriate to address the issue of quantifying the uncertainty necessary to be incorporated in the systems of reserves classification.

Jan 1, 2002

By R. J. Andreini

Solvent extraction is widely used in hydrometallurgical processing of uranium for purification and upgrading leach solutions prior to recovery of metal values. Conventional solvent extraction processing utilizes mixer-settler units to achieve mixing of the aqueous and organic phases. Use of mixer-settlers permits continuous treatment of feed, but the processing rate is restricted by the time required for phase separation after mixing. Because of the high-shear type mixing used in a mixer settler a portion of the organic phase becomes mechanically entrained in the aqueous resulting in loss of extractant. For this reason application of mixer-settler units is often limited by the settling area required for phase separation, especially for systems where high volume throughputs are desirable or necessary. Several alternatives to mixer-settler operations involving the use of column extractors have been proposed. Packed columns (1-2), in which organic and aqueous phases are fed countercurrently, utilize packing materials similar to those used in gas absorption or distillation columns. Extraction columns utilizing rotating(3-5) or reciprocating elements(6-7) to achieve mixing have also been developed. Van Dijek(8) originated pulsed columns, in which mechanical or air pulsing of the phases enhances the mixing in the vessel. Each of the above column processes involve varying degrees of mechanical complexity which may lead to operational difficulties.

Jan 1, 1975

By Takeshi Shinohara

It is a great honor and pleasure for me as President of the Japanese Tunnel Association to send greetings to the 1974 Rapid Excavation and Tunneling Conference. Recently in Japan, the Japanese Tunnel Association was established as recommended by the OECD Advisory Conference on Tunneling. This is a central organization concerned with tunnel construction consisting of government authorities, universities&apos; research institutes and construction firms as well as manufacturers of relevant materials and equipment. As I was chosen the first president of the newly-established Japanese Tunnel Association, I would like to avail myself of this opportunity to announce to you its establishment and its earnest wish to contribute to the development of tunneling technique not only in our country but also all over the world. At the same time, I cordially request your friendship and cooperation for the benefit of further development of tunneling techniques on both sides of the Pacific. At present, many tunnels are under construction in Japan. The total length of tunnels under construction for railways and highways is about 600km including the 54km Seikan Undersea Tunnel which connects the Main Island and Hokkaido. Naturally, for construction of such tunnels in Japan, we have introduced much equipment and technique from the United States and other foreign countries. Now with accumulated experience, we are confident to be able to furnish various useful information concerning tunnel construction.

Jan 1, 1974