Search Documents

By E. Cameron

Yeelirrie lies toward the center of Western Australia, 650 km (404 miles) northeast of Perth (Fig. 1). The ore reserves have been estimated as 52.5 kt (57,871 tons) of contained U3O8, at an average grade of 0.15%, of which almost two-thirds average 0.24% U3O8. the ore body is a thin, elliptical, more or less horizontal sheet measuring approximately 9 km (5.6 miles) in length, between 0.5 and 1.5 km (0.3 and 0.9 miles) in width, and up to 7 m (23 ft) in thickness, extending from the surface to a depth of 8 m (26 ft). In spite of its near surface position, there is only one small outcrop of significant mineralization. Carnotite is the only uranium mineral recognized so far, dispersed through a calcrete horizon, and deposited from circulating ground water which was also responsible for the carbonation of the clays completely filling an Early Tertiary drainage system. Calcrete, as seen at Yeelirrie, is quite distinct from the widespread, thin pedogenic horizons, as it often forms bodies many kilometers in length and up to 20 m (65.6 ft) in thickness, elongated parallel to the drainage lines. It is variously referred to as "valley calcrete" or "ground water calcrete" to emphasize the occurrence and mode of origin. The discovery of Yeelirrie in mid-1971 was the successful culmination of a grass-roots exploration program initiated in 1968 as part of Western Mining Cop's program of diversification from its historical position as a major gold producer. The object was simply to find an economic uranium deposit - with no constaints other than those normally taken as applying in the mineral search. There was, therefore, complete freedom in the selection of the exploration model, or models, to be applied and the areas to be considered, though the choice was inevitably influenced by both the nature of world occurrences and the local geology. One of the options avail- able was the sandstone environment. Yeelirrie was the direct result of pursuing this line of investigation through three sequential, but quite distinct, stages: first, a regional study; second, establishing a case for exploring the inland drainage systems of Western Australia; and finally, an evaluation of the calcrete environment. An assessment of the potential for sandstone-type deposits in Australia necessitated going back to first principles, since there were no known precedents in this country for guiding exploration and, as a consequence, the search need not be influenced by established prejudices. Previous uranium exploration during the 1950s had been preoccupied with vein-type deposits, and, although the sandstone environment was undoubtedly being examined in 1968, no discoveries had been announced to that time. When considering the necessary ingredients -a source of leachable uranium, a circulating ground water system, and a suitable reducing environment - it could be argued that considerable areas in the eastern part of the continent were theoretically prospective, but basin depth and the extensive superficial cover of Mesozoic and Cainozoic sediments presented considerable practical difficulties.

Jan 1, 1991

By C. M. Brown

Common operating philosophies and objectives of mining and mineral process operations are discussed. Key information required to effectively monitor operations is reviewed in conjunction with the impact of external variables such as commodity price changes on strategies adopted.

Jan 1, 1991

By Adam Graf

Mineral deposits are fundamentally different from most other assets -Every deposit has unique geologic and metallurgical characteristics -Asset (resource) is finite and cannot be truly replaced. -Long timeframe and time-value of reserves -Commodity price volatility (see Torries, 1998)

Jan 1, 2003

By Michael M. Donahue

"The public interest -- as opposed to the narrow interests of particular shippers -- will also benefit from the establishment of adequate revenue levels and the revitalization of the railroads. And this is particularly true with respect to the transportation of coal. "

Jan 1, 1981

By G. Granger, D. Malhotra

The paper briefly reviews the criteria employed in the selection of chemical reagents for testing and discusses the steps involved in laboratory and plant evaluation of these reagents. An example of successful implementation of reagent change in the plant is illustrated.

Jan 1, 1986

By R. J. Pruett, J. Yuan

Kaolin clays from five different commercial deposits in Georgia were studied to understand the variations of zeta potential and related fundamental properties. The results suggest that higher negative zeta potential is related to exchangeable or soluble calcium ions in the clays.

Jan 1, 1999

By D. W. Fuerstenau, S. Raghavan

This paper presents a brief summary of some of the thermodynamic aspects of flotation processes. Thermodynamic considerations that control interfacial and wetting behavior in mineral/water/air systems are discussed. Particular attention is given to the thermodynamics of collector adsorption.

Jan 1, 1976

By Michael Hood

Subsidence profiles above two adjacent panels in Illinois are compared with pro- files predicting subsidence behavior obtained using the (i) National Coal Board (NCB, 1975) method, (ii) the profile function method and (iii) the influence function method. The NCB method predicts the maximum subsidence values at the center of the troughs accurately, but, the overall shapes of these predicted profiles do not match the profiles from the measured data well. Consistent values for the angles of draw were measured but these angles were different in the transverse (average value 43 degrees) and in the longitudinal (average value 17.5 degrees) directions. Time dependent subsidence effects are shown to be small but measurable. These displacements continue at a linear rate for at least a 12 month period. A comparison of measured horizontal distances, interpreted as horizontal strain, and the NCB predictions for strain shows that the peak measured strains are greater by a factor f about four than the predicted strains. The relationship between surface curvature and strain is investigated. Problems associated with calculation of surface curvatures from vertical displacement data are highlighted and a recommendation is made for future studies to consider direct measurement of this parameter. Surface curvatures above a moving face are found to be about three times less than the curvatures at the stationary end of the panel. On the other hand, a hyperbolic tangent profile function is shown to serve as an accurate predictive tool for subsidence behavior in two adjacent longwall panels at Old Ben Number 24 mine in Illinois. This function predicts not only the vertical displacements but also the surface curvatures above both panels. Influence functions are shown to be more problematic, although potentially more flexible, in their application than the profile functions.

Jan 1, 1982

By Jafar Khademi Hamidi

The Zagros long tunnel is one of the main components of Sirvan water transfer project in western Iran. It is approximately 48 km in length and consisted of two lots. The second 26 km lot of this tunnel is under construction by a 6.73 m diameter double shield (DS) TBM. The tunnel passes through several formations with wide range rock mass qualities. During the tunnel alignment, changes in rock quality were highly frequent from poor to very good. The encountered geological conditions required TBM operation to change frequently from hard rock to soft, dry to flowing, sticky to nonsticky ground (and vice versa), more often than expected. In the course of tunneling, the machine has encountered nearly many adverse geologic conditions. The most important problems have been sudden high volume water inflow into the tunnel, sticky ground, and gas seepage, all of which resulted in reduced TBM advance rates. This study will high-light two difficult ground conditions including large water ingress and sticky ground and also the related problems encountered by the TBM along 8 km of excavated tunnel. In sticky grounds, cleaning of the clogged cutter head caused many delays and contributed to additional downtime. Application of some operational modifications, including decreased TBM thrust showed satisfactory results in such cases. While reduced thrust resulted in reduced penetration rate, but the overall TBM advance was greatly improved by the increase utilization rate and elimination of down time related to cleaning of the head. To cope with high water inflow, application of preventive measures such as pre-grouting has proved to be a more efficientsolution. The sealing of ground water inflow also decreased seepage of dangerous H2S gas and other chemicals such as hydrocarbons accompanying the groundwater.

By Richard A. Bideaux

With both unit costs per meter and average depth of drilling constantly increasing, there is a strong incentive to maximize the information acquired from drill holes, and then to make this information accessible to the geological staff. The larger the drilling project, the more advantageous computerization of data is over manual methods. The conversion to computer-readable form and the verification of large amounts of drill-hole data can be a substantial data processing task, but once accomplished, the benefits in increased accuracy and speed of interpretation will compensate for the time and effort spent in the work. For an exploration project progressing towards a preliminary feasibility study, about half of both the time and costs for all computer work of the entire feasibility study are devoted to drill-hole data base organization, and maintenance. Once drill-hole results are quantified and verified to be correct, they are immediately accessible and are not subject to further transcription or reinterpretation of errors. To obtain maximum benefits from computer utilization in this area, the drill-hole data base should be set up along with availability of the first data. For some companies, this may initially comprise a large number of purely speculative drill holes on a spacing of perhaps 1 or 2 km. Although few of these drill holes may encounter economic material, thought should be given, at this time, to the variables which will be logged when such material is found. In this way, it should be possible to set up a consistent format into which all future drill-hole information will readily be accommodated. This format may even be carried over into the data base requirements for an operating property.

Jan 1, 1979

By D. E. Walsh

With the exception of the development of large scale mining equipment (haul trucks, draglines, shovels, etc.), there are likely few other candidates responsible for the ability to exploit large tonnage, low grade deposits, than the development of large capacity comminution equipment and circuits; crushers and grinding mills. Ball mills are often the final step in the comminution process and are responsible for providing what should be the optimum particle size distribution of ore to subsequent mineral concentration steps in the flowsheet. Because comminution processes are such high cost centers for milling operations, both capital and operating costs, an enormous amount of research has been conducted to study and model their performance, in order to improve efficiencies (Kelsall, et al., 1969; Austin et al., 1984; Napier-Munn, et al., 1999; Powell and Smit, 2001). With respect to modeling ball mills, estimates of the breakage rates for individual size classes of ore particles are fundamental, as are the particle size class breakage functions (the progeny of particle sizes produced from breaking a coarser particle size class), also termed appearance functions. Fundamental research into particle breakage in tumbling mills focuses on how much energy is input into single particles versus how they break and what size distribution of particles results. Several test methods, including JKMRC?s well known dual pendulum test and drop weight test, have been developed for the breakage of coarse particles down to 6 mm in size (Napier-Munn, et al., 1999). Work on the breakage of finer particles is still an area of intense research and single particle breakage is being investigated as are multiple particle, fixed bed methods (Hoffler and Herbst, 1990; Bourgeois et al., 1992; Whiten, 2007).

Jan 1, 2011

By C. K. Kocsis, S. Hardcastle

Mine ventilation, requires electricity to operate the fans and fossil fuel for heating. Typically, this accounts for approximately 40% of the overall underground energy consumption. This is considerable, and one of the major causes of this expense is that most mine ventilation systems are designed for the "worst-case-scenario" with respect to ventilation demand, which is commonly dictated by diesel equipment usage. Once designed, mines tend to operate their ventilation system at this peak level despite their exceeding day-to-day development and production needs due to lack of appropriate ventilation controls. In underground metal mines, TeleminingTM, which includes the tele-remote operation of mobile development and production equipment from surface, will change the mine design criteria including its support infrastructure such as the ventilation system. With the removal of machine operators to surface control rooms, conventional ventilation systems designed to dilute and remove pollutants can become redundant. Depending on the ultimate need for ventilation, its cost in automated mines with tele-remote equipment operated from surface will be lower than the cost of ventilation in conventional mines. These cost savings, which could be significant, would not only come from the ability to reduce the amount of ventilation in the mine, but also through the capacity to automate its distribution. This paper provides an indication of the new airflow requirements in stopes and dead-end developments for the tele-remote and automated mining processes based on climatic modelling. Furthermore, this paper makes a cost benefit analysis by comparing the ventilation system operating cost of a conventional underground metal mine based on the mobile diesel powered equipment design criteria with the newly redesigned ventilation system operating cost of an automated mine based on the "heat management" design criteria.

Jan 1, 2002

By Lawrence Pelham

Introduction Fluorspar demand or consumption has been taken for granted in recent years, except for those that produce, market, or consume the commodity. Thinking used to be that as the steel and aluminum industry goes, so goes fluorspar. This is much less true today. The industry is becoming more dependent on chemical industries that feed primarily off hydrofluoric acid (HF) production. The US Bureau of Mines (USBM) published an assessment of world fluorspar reserves and resources. It created a foundation of valuable data that can be used to monitor fluorspar availability. Celebrations were held this year commemorating the 100th anniversary of the isolation of fluorine. The US and other countries continue to struggle with the controversy of ozone depletion and the effect of fluorocarbons on the atmosphere. Goals for the government's strategic stockpile are being reevaluated. The market for fluorine chemicals is changing and diversifying, making it a challenge to assess and forecast fluorspar/fluorine demand. US production and distribution Fluorspar Fluorspar shipments from US mines reached an all-time high near the end of World War II in 1944 at 375 kt (413,800 st). Eighty-two mines produced more than 453 t (500 st) each, and 10 mines produced more than 9 kt (10,000 st.) each. Illinois supplied 43% of total shipments. Consumption in 1944 was 372 kt (410,200 st), of which 56% was used by steel producers and 32% by HF producers. This was the last year that US production exceeded US consumption. The post-World War II record for fluorspar shipments occurred in 1951 at 315 kt (347,000 st) 58 mines produced more than 453 t (500 st) and eight mines produced more than 9 kt (10,000 st).

Jan 11, 1986

By Richard C. Neavel

Among the many compositional parameters used to judge the quality of a steam coal is the fouling factor of Attig and Duzy1 [% base in ash % acid in ash X % Na20] in ash. The higher the fouling factor, the more likely the heat transfer surfaces of the boiler will acquire a deleterious deposit of sintered ash. While examining the elemental composition of ash from various size and gravity fractions of coals from Illinois, we noticed that variations in the fouling factor were attributable mostly to variations in the sodium content. Further, sodium content was essentially the same in all sink-float fractions from a given coal. In other words, sodium was related neither to the ash nor to the organic material. We therefore concluded that the sodium was most likely in the pore water, which was approximately a constant proportion of all fractions. This led to the supposition that the sodium might be removable through water extraction. This supposition tended to confirm the observations of Daybell,2 Daybell and Gillham,3 and Gluskoter and Ruch4 that much of the sodium in coals existed as water soluble sodium ions. In passing, it should be noted that most sodium in Western U.S. coals (i.e., Wyoming, North Dakota, Montana) is not water soluble, but rather is fairly strongly held in association with the organic material (ion-exchanged).5 Because data reported in the literature were not very conclusive about the typical proportions of sodium that might be removed by water extraction, and because there were few data indicating extraction rates, and finally, because our calculations showed a favorable economic incentive to lower sodium contents, we initiated an experimental program to investigate water extraction of sodium from Illinois coals.

Jan 1, 1976

By Barton J. Suchomel

Introduction Despite perennial economic turbulence, Argentina continues to push ahead with efforts to develop its fledgling hardrock mining industry. The country lacks the infrastructure and mining history of neighboring Chile, but contains vast areas of great resource potential. The eastern slope of the Andean Cordillera in west-northwest Argentina is a relatively little-explored region offering geology highly conducive to the occurrence of base and precious metals deposits. Past exploration has concentrated on locating and evaluating porphyry copper-molybdenum (Cu-Mo) type occurrences. Comparatively little attention has been given to precious metals potential. An interesting and important group of base and precious metals prospects in northwestern Argentina occurs within and adjacent to the Upper Miocene Farallon Negro volcanic complex in Catamarca province. The volcanic complex contains numerous base and precious metals vein occurrences, high gold porphyry copper prospects, and possible disseminated gold targets that have attracted relatively minor attention in the past. Various geologic aspects of the region have been reported by several workers (Llambias, 1970, 1972; Caelles et al, 1971; and Sillitoe, 1973). Regional geology The Farallon Negro volcanic complex is located within the Sierras Pampeanas morphostructural province about 200 km (125 miles) east of the main Andean Cordillera (Fig. 1). The Sierras Pampeanas is characterized by north-south-trending basin and range topography that developed during the Miocene and Pliocene. Uplifted blocks are composed mainly of lower Paleozoic metasediments and granitoid plutonic rocks unconformably overlain by Tertiary redbeds and minor carbonates. A consistent landward migration of volcanic and intrusive ac¬tivity occurred in this region of the Andes from the early Mesozoic through the mid-Tertiary. An eastward extension of magmatism during the Miocene and Pliocene resulted in the formation of the Farallon Negro volcanic center. Volcanism at Farallon Negro ini-

Jan 8, 1988

By Xuehua Zhang, Shengxiong Yang, Huiqiang Yao, Gaowen He

"Seamount cobalt-rich ferromanganese crusts (hereafter crusts) are authigenic iron/manganese hydroxide/oxide deposits formed from direct precipitation of minerals from seawater onto a hard substrates surface. Crusts contain significant concentrations of cobalt, manganese, nickel, copper, platinum, rare earth elements and other valuable metallic elements, with potential economic value. Regulations on Prospecting and Exploration for Cobalt-rich Ferromanganese Crusts in the "Area" was approved by the Council and Assembly of the International Seabed Authority in July 2012, China and Japan became the first to obtain exploration contracts, which were signed respectively in April and January 2014.The crusts form pavements and are mainly attached tightly to the surface of the substrate, and less commonly crusts coat talus debris located on the surface of sediment and substrate rock. During prospecting, crust sampling methods mainly include dredge, TVgrab and sub-bottom coring system. During exploration, the sub-bottom coring will be the dominant method for crust sampling, and if necessary, ROV sampling will be used. Usually the samples collected by different methods provide a larger quantity than samples needed for chemical analysis, but sampling quantity is a question that should be considered for mineral resource evaluation that how to ensure that the sampling is representation for the sampling station. Using the samples collected by China from Pacific seamounts, according to the designed analysis flow and Qeqott formula (Q=Kd2), the minimum reliable assay sample quantity ("MRASQ") of crusts for Mn, Co, and Ni are obtained. In the case of the sample homogeneous fines at ~100 mesh size (~0.15 mm), MRASQ for Mn, Co, Ni is respectively 4.5 g, 9 g and 9 g. This result provides the basic data for crusts resources evaluation."

Sep 1, 2014

By Julian Prada

Tunneling requirements are presenting designers with greater challenges. The design and construction of the 2000-ft long unidirectional twin highway tunnels for the approach to one of two bridges of the Louisville-Southern Indiana Ohio River Bridges (LSIORB) Project is no exception. Excavation under low cover, beneath an historic site, with each tunnel of 70-feet wide and 50-feet high dimensions will set precedents for US highway tunnel excavation size. To investigate ground conditions to supplement final design of the highway tunnels, an exploratory tunnel excavated through karstic limestone and shale will be located within the confines of the proposed final alignment. With the LSIORB Project, Jefferson County, Kentucky and Clark County, Indiana will have improved cross-river mobility between them. The Indiana Department of Transportation (INDOT) and the Kentucky Transportation Cabinet (KYTC) are developing the LSIORB Project jointly, in coordination with the Federal Highway Administration (FHWA). Section 4, one of six sections, as shown in Figure 1 is the East End Kentucky Approach and Connections to I-265. Key elements of Section 4 are the twin three-lane highway tunnels under the historic Drumanard Estate. The property is located on the north side of US Highway 42 (US 42) at the intersection with the Gene Snyder Freeway (also KY841) as shown in Figure 2. One aspect of the project consists of the excavation of an Exploratory Tunnel along the southbound alignment tunnel. At the time of preparation of this paper, KYTC has not awarded the Exploratory Tunnel Contract. This paper will focus on the planned geotechnical investigation program that will occur during excavation of the exploratory tunnel and how the design of the twin highway tunnels will incorporate the findings to achieve an innovative and efficient configuration.

Jan 1, 2008

By R. L. Derick

On a regular basis, mine personnel should obtain air samples directly from active underground areas as well as remotely from sealed locations. These samples provide mine officials with data relative to the makeup of the various atmospheres. Should conditions underground change, these results can provide a baseline that can assist officials in determining the extent of change. Relating the concentrations of individual gases to time, applying gases to equations, and examining their change over time are tools that have been successfully used to determine if a heating event exists and, if so, the extent of the emergency. These atmospheric status equations have either been developed for the mining industry or adapted from other industries. They serve as tools to assist personnel in determining the condition of underground mine atmospheres. As long as the problem area continues to be ventilated, certain gases, gas ratios, and equations can be used to determine if a fire exists, what type of material could be burning, and what quantity of coal is burning. Once the mine or the involved section has been temporarily sealed, gases, ratios, and gas-derived equations can assist personnel in determining how conditions within the sealed volume are changing over time. To alleviate potential explosions when fresh air is once again introduced into the sealed volume, equations and a diagram have been developed to predict the likelihood of an explosive atmosphere. Similarly, prior to commencing recovery of a mine or section, equations exist that can assist in determining if the fire will rekindle when air is reintroduced. This paper serves as an overview to remind and/or instruct readers about gas-sampling methodologies and gas analyses to assist in determining the status of underground atmospheres.

Jan 1, 2006

By Frank F. Rahne

Butler Taconite, operated by the Hanna Mining Company, is an Iron ore pelletizing operation that is located on the Western end of the Mesabi Iron Range in Northeastern Minnesota. The operation mines low-grade taconite ore and through primary crushing, two stage grinding, magnetic separation, agglomerating and indurating, produces 2.6 million annual tons of high quality, 66% iron pellets. Mining and stripping is done with 13 - M100 trucks and 5 - 12 cu. yd. shovels. The operating processes in the concentrator and pellet plant are primarily con¬trolled through a centralized control room and monitored by a PDP l140 computer. During 1969 and 1970, a re-organization of the Company took place. Through this re-organization, each mine unit was analyzed and studied to determine the proper staffing of the internal departments. At this time, it was decided to continue with further detailed studies of the Maintenance Department with the intent to reduce maintenance costs. Maintenance costs at the time of the re-organization were 38.6% of the total mine operating cost. The preliminary study indicated that the Maintenance Department had a system of maintenance, as a matter of fact, it had a separate system in each sub-maintenance division and in some of the sub-divisions each foreman had a system of his own. Therefore, from the data collected, it was decided to develop one system of maintenance that could be utilized throughout the entire operation. To determine the type of system suitable to all phases of the operation, detailed time and method studies were conducted. All types of maintenance tasks performed at the operation were studied. The data collected was analyzed and the recommended improved methods were reviewed with the Maintenance Superintendent and his staff. The new improved methods that were accepted as feasible, were introduced into the system immediately.

Jan 1, 1975

By G. S. Walker, W. van Bronswijk

The accurate determination of free cyanide and metal cyanide complexes is of increasing interest to Carbon-in-Pulp (CIP) gold extraction operations as cyanide consumption is an important economic factor in the processing of complex ores. Characteristically complex ores are high cyanide consumers and these ores usually contain a range of sulfide minerals e.g. covellite (CuS), digenite (Cu1,S), chalcocite (Cu, S), Pyrrhotite (Feci-x)S), marcasite (FeS2), arsenic and antimony sulfides and zinc sulfide. These minerals can consume significant quantities of cyanide, e.g. various copper(!) cyanide complexes such as CuCN, Cu(CN)2·, Cu(CN)/ and Cu(CN)/ can form, depending on the cyanide to copper ratio in solution. Measurement of free and complexed cyanide is thus a prerequisite for efficient cyanide dosage control. Free cyanide can be determined potentiometrically or amperometrically but the methods are prone to error and are laborious [1]. Metal cyanide complexes can be determined by reverse phase HPLC, however, the species ofa single cation (e.g. Cu(CN)i-, Cu(CN);2 and Cu(CN)/) elute as one species [2]. Additionally the high amount of suspended matter in CIP leach solutions tends to introduce errors. Raman spectroscopy has the potential to be used as an in­line or on-line method of analysis. Free cyanide and the cyanides of gold, silver, copper and iron have been studied in aqueous alkaline solutions with a view to developing such a method. Spectra were obtained with a Bruker RFSl00 FT-Raman spectrometer using a 1064 nm laser delivering 800 mW of power at the sample. Depending on the solution, 250, 1000 or 4000 scans at 4 cm-1 resolution were accumulated. The cyanide stretches observed were relatively narrow (10 15 cm-1 full width at half height) and well resolved (Figure 1 ).

Jan 1, 1995