Search Documents

By S. K. Sharma

The Bureau of Mines has investigated the fundamentals of the flocculation process. The objective of this study was to determine the effects of various physico-chemical parameters such as shear rate, polymer dosage, and polymer concentration on floc growth and to determine the applicability of a model in predicting polymer flocculation behavior. A rapid in-line particle size analyzer was used to follow the progress of both the floc growth and the breakage as a function of time. A genetic algorithm (GA) was used to determine the unknown parameters in the model and to fit a curve to the experimental data. Results show that the model, using GA as a tool to determine the unknown parameters, reproduces the experimental data with only reasonable accuracy and was relatively insensitive to the parameters. Results of the flocculation study showed that increases in polymer dosage had greater effect on the time required to reach the maximum floc size than on the floc size itself. It was also determined that, given all the aforementioned parameters, the degree of slurry mixing during the flocculation process had the greatest bearing on the floc growth.

Jan 1, 1993

By Richard Chojnacki

The western united States is not usually noted for the production of fluorspar; however, many significant fluorspar districts do occur in the Rocky Mountain region and constitute a resource of sizable dimension and major potential. This is particularly true within the area of the West served by the rail lines of the Union Pacific Railroad (see Figure 1). Fluorspar deposits near the Union Pacific have produced over 1.3 million tons of finished fluorspar products from 2.3 million tons of ore. Approximately 80% of this production was of acid-grade and 20% of metallurgical-grade fluorspar. Production of ceramic-grade was negligible. Through the years substantial production has come from eight mining districts. Five of these have produced metallurgical-grade and three acid-grade. The best-known fluorspar producing area in the West is the Jamestown Mining District. It was one of the first producers of fluorspar in the western United States and is estimated to have produced over 500,000 tons of finished fluorspar from over a million tons of ore. The district encompasses approximately 36 square miles in central Boulder County, Colorado, about 9 miles northwest of the City of Boulder. Although small shipments were made from the district as early as 1873 or 1874, significant sustained production was not achieved until 1940 when the General Chemical Company, now a division of the Allied Chemical company, acquired the Alice, Burlington, Chancellor,

Jan 1, 1971

By David Morrison

"The history of the mining industry is littered with in-pit crushing and conveying (IPCC), which should not be confused with the International Protocol for Carbon Capture, projects that failed. The failure is not the technical one of “did it achieve the desired tonnage rate for a longish test period” but, rather, the far more important one of “did it provide return on the investment in the manner that was promised?” While quite a few can claim the former, very few system installations can claim the latter.The reasons for the many failures are numerous, but they are all characterized by a combination of an element of engineering optimism in any, or all of the production rates, the productivity, or the operating and maintenance costs and in predicting the continuity of operating conditions. In these days of big data, propagating such a situation is rapidly becoming unforgivable.In this article, the three most common scenarios put to the corporate board for approval, and the logic as to why they were selected, are examined (with the irony included intentionally).• Fully mobile crusher, fed by a shovel and conveyed out of the pit to a waste dump / process plant.• Semimobile crusher (much more expensive than a fixed crushing station but which apparently allows trucks to short haul inside the pit and improve productivity), which moves when the face moves.• Relocatable crusher (more expensive than a fixed crushing station but which gets relocated at great expense after all the fixed infrastructure impeding relocation is demolished) fed by trucks that don’t leave the pit mostly.This paper will also consider the truth about their operational performance and associate costs."

Dec 1, 2016

By M. Yavuz

Due to workability difficulties, people have begun to use iron ore much later than gold, copper and bronze. In addition, iron and steel products are the most commonly used metals which are necessary for human life today. It is a fact that iron ore is raw material of the steel production process as known. Iron&Steel sector is plays an important role in the economic development of countries all over the world. Therefore, the amount of production and consumption of steel is one of the basic indicators of industrialization all over the world. The amount of steel consumed per capita of the country is considered as a measure of development. The world average per capita consumption of steel is around 210 kg in 2007 (Yildiz, 2009).

Jan 1, 2010

By A. Fuerst

This paper delivers insights into how high availability combines with high efficiency at the Yanacocha Plant, Newmont Mining Corporation, Peru. Advances in motor design and maintenance with integration of smart control support the approach plant maintenance staff is applying to deliver such excellent results for availability and efficiency in Yanacocha and elsewhere. Detailed efficiency and availability data for 2011 and 2012 in Yanacocha are provided. ABB and Yanacocha teams collaborate closely by combining their experience and continuous development of gearless mill drive procedures and maintenance knowledge to deliver the impressive performance being achieved. The secrets for high performance shared by the Yanacocha maintenance operations point to their systematic, practical adherence to modern asset management and maintenance concepts.

Feb 27, 2013

By Irina Chernyshova, Erik Larsen, Hanumantha Rao Kota, Vladislav Slabov, Garima Jain

The separation of fine mineral particles, especially using environmentally friendly approaches, is one of the main problems in the processing of low-grade ores and the re-processing of mining tailings. This work assesses the potential of biosurfactants as collectors in the flotation of ultrafine (smaller than 20 μm) particles of hematite and malachite. As biosurfactants, we test acetylated acidic (ac-ASL) and lactonic sophorolipids (ac-LSL). In addition, n-dodecyl-β-D-maltoside (DDM) is used as a model non-ionic alkyl disaccharide surfactant, and sodium oleate (NaOl) is used as a reference. The biosurfactants are characterized using surface tension and foam analysis. The interaction of the minerals with the surfactants is characterized using zeta potential, solubility, and single-mineral flotation. The collecting properties of the surfactants are compared for the ultrafine (− 20 μm) and coarser (38–90 μm) particle size in the two-mineral flotation of hematite and malachite against quartz. The ultrafine particle size improves the grade in the oleate flotation of hematite, as well as the grades in the DDM flotation of hematite and malachite, which is explained by the weak interactions of the metal oxides with fatty acids and DDM. At the same time, the flotation with ac-LSL and ac-ASL is highly tolerant to the ultrafine particle size. These results indicate that biosurfactants are an interesting alternative to conventional petroleum-based surfactants in the flotation of Fe and Cu oxides. Moreover, a proper selection of surfactants can help combat the problem of fines.

Feb 23, 2023

Projections of coal reserves in Central Appalachia are essential for long-term planning in the region. Annual production is declining in some states, such as Virginia, and mineable reserves for the Central Appalachian Coalfield are challenged by difficult geological, mining, and market conditions. In order to project coal mining longevity in this region, interviews with mining companies were conducted to assist in the determination and assessment of technical and economic factors that impact coal seam mineability. This information was applied to seam and coal reserve data developed by state and federal governments. The results were carefully analyzed to determine the effects of various factors on the overall mineable coal reserve base.

Jan 1, 1998

By Yun-tao Xin, Yu Yi, Kang Yan, Gang Li, Xiao-dong Lv

This study investigated the selective removal of arsenic from high-arsenic dust in alkaline systems and the effects of different leaching conditions. The results indicated that the liquid–solid ratio, NaOH concentration, and sulfur dosage had a significant influence on the process. The leaching efficiency of arsenic reached 99.57%, while that of lead was as low as 0.03% under appropriate conditions. In particular, the addition of sulfur can effectively promote the leaching of arsenic and reduce the dissolution of lead in the solutions. An artificial neural network was used to model the leaching process. It consisted of a back-propagation artificial neural network model with a “6–10–2” structure that could effectively simulate and predict the value with more than 99% accuracy. Based on the difference in weights of the different parameters in the neural network model, the relative importance of the parameters related to arsenic and lead leaching efficiency was obtained, which followed the order of NaOH concentration, liquid–solid ratio, sulfur dosage, temperature, time, and stirring speed.

Jul 29, 2021

By William G. Wilson

In the U.S. today a number of tentative synthetic fuel plants have been sited by a number of major corporations. Each of these for a number of reasons have deferred construction. The only synthetic fuel plants under active development are those being built with the Energy Research and Development Administration (ERDA) under the authority of the Non-nuclear Energy Research and Development Act of 1974 (Public Law 93-577). Under this Act in joint sponsorship with industry, a series of coal conversion pilot and demonstration plants are being built to produce environmentally acceptable fuels from high sulfur coals. Before entering into a discussion of the factors associated with the siting of the ERDA coal conversion program, the difference between a pilot plant and a demonstration plant should be explained. The terms pilot plant and demonstration plant iridicate a size of plant rahter than technology. A pilot plant will vary from an "add-on" to an existing facility to an independent unit. Demonstration plants are a wholly independent, self contained plants, capable of independent operation to demonstrate the environmenta1, economic, and technica1 feasibility of a technology. These plants are from one-third to one-tenth the scale of a commercial operation and often described as plus 1000 tons per day of coal consumption. Their purpose is stated in the Act (Section 6, (3)(E),) "to accelerate the commercial demonstration of technologies for producing syncrude and liquid petroleum products from coal: Provided. That the Administrator shall invite and consider proposals from potential participants based upon Federal assistants and participation through guaranteed prices or purchase of the products .... " In site selection and plant design it has been suggested that special interest groups should be allowed to dictate the site and specify the design. Under the present program the industrial partner who is contributing 50 percent

Jan 1, 1977

By Steve Kral

"The Rapid Excavation & Tunneling Conference (RETC) is a world-renowned event that attracts some of the best minds in the global underground construction and tunneling industry. The experts gather at this conference to impart new technologies, discuss challenges to their projects and learn about new technologies that have become available to them.The 2015 RETC will be held June 7-10 at the Sheraton New Orleans, in New Orleans, LA. This biennial conference, of which SME is a sponsor, is expected to attract about 1,400 attendees from around the world. These professionals represent all parts of the global tunneling and underground construction industries - contractors, engineers, owners, consultants and equipment suppliers.More than 110 technical papers in 21 sessions will be presented over two-and-a-half days. Paid attendees will receive a proceedings volume of the conference. The proceedings will also be available from SME. In addition to the technical programming, the accompanying exhibit will include 155 exhibitors occupying 175 booths, providing RETC attendees the opportunity to get a look at the latest in equipment and service technology. Three short courses will be held on the Sunday preceding the start of the show. And there will be plenty of opportunities for attendees to meet and chat during several social activities that are scheduled throughout the conference."

Jan 1, 2014

By James P. Connell

The American Concrete Institute defines "shotcrete" as "mortar or concrete conveyed through a hose and pneumatically projected at high velocity unto a surface." This definition thus includes what is traditionally known as "gunite," which is a pneumatically applied mortar. In mining practice, the term shotcrete is restricted to pneumatically applied concrete, and this differentiation will be used in this paper. In 1914, following the invention of the mortar gun in 1907, the then Chief Engineer of the U.S. Bureau of Mines, George Rice, developed the guntie process for underground test work at the bureau facility at Bruceton, Pennsylvania. After World War I, gunite was used extensively in American mines and was also utilized for underground civil works such as the San Jacinto Tunnel in California. The greatest development was In Europe where, as early as 1911, gunite was successfully used as an overlay for deteriorated tunnel linings. In 1951, the Swiss firm Aliva developed a pneumatic gun capable of handling coarse aggregate, thus making possible the first use of shotcrete at the Maggia hydropower development. Intially, shotcrete was used to reduce manpower requirements for forming; and placing conventional concrete. However, by 1954 Sonderegger was reporting that the structural advantages of shotcrete were derived from its flexibility and from the fact that it could be applied almost immediately niter the opening had been made. The incorporation of wire mesh into the shotcrete led to the New Austrian Tunnel Method, or NATM. The use of shotcrete in American mines has been implemented more recently. This delay seems to be due to previously unsuccessful experiences with gunite as a structural material and to the U.S. reliance on wood or steel supports in main line haulageways. The long experience with the apparently more substantial rigid supports led mine operators to be reluctant to the new and seemingly unrealistic lighter shotcrete support.

Jan 1, 1977

By L. Galarza

"INTRODUCTION Beneficiation of ores and minerals in a concentrator plant requires a significant amount of water [1] for the grinding and particle separation processes; most of it ends up being recirculated for reuse, slurry pumps are used after crushing and grinding feeding the ore to a classifier to separate fine-grained material (less than 5 mm) from coarse-grained material requiring further grinding. The lower ore grades [2] in the past couple of decades have demanded an increase on power size and efficiency of process machines to maintain a competitive plant throughput; Hydro-cyclone feed pumps to control both under and over milling or grinding are not the exception; Fig. 1 shows a conventional drive train [3] comprising an (1) asynchronous motor (also known as squirrel cage induction motor = SCIM), a high speed coupling (2), a gear reducer (3) and a low speed coupling (4) attached to the shaft of the pump (5), to accommodate the motor rated speed (typically 1800 rpm) to the process requirements (in the range of 250 rpm to 350 rpm), requiring additional components related to the gearbox: instrumentation, maintenance, disposable lubricants and filters, spare parts, thus reduces the overall system efficiency ultimately reflected into CAPEX and OPEX.WHY VARIABLE SPEED DRIVES FOR CYCLONE FEED PUMPS Hydrocyclones or commonly referred as “cyclones” are one of the most important devices in the minerals industry [4]; almost universally used in close-circuit grinding because of their high capacity and relative efficiency, the evolution of Power Electronics made affordable the use of Medium Voltage - Variable Frequency Converters (VFC) for Cyclone Feed pumps in combination with induction motors larger than 500hp (373kW) to gain multiple benefits: - Soft start with minimum electrical utility disturbance = inrush current mitigation - Full Torque available at zero speed for overload startup with pulp solidification after long still stand periods, superior to any other reduced voltage starting method. - Optimum and constant pump speed (independent of the electrical network or load condition), compared to across the line SCIM operation - Flexible Motor Voltage and Speed regardless of the power distribution Voltage and Frequency - Improved Power Factor (close to unitary), over the entire operating speed range"

Jan 1, 2015

By Prasad S. Mulukutla

INTRODUCTION The use of specialty chemicals In mining Is an Important consideration In determining the economic efficiency of a floatation plant. The plant metallurgist would like to maximize the recovery of valuable minerals while maintaining an acceptable grade product. The direct cost of the reagents, while significant, Is only a part of their economic effect. Reagents determine the flotation rates and the selectivity of the mineral separation. In flotation practice, mineral selectivity can be achieved through the addition of various reagents that can control the wettablllty of a particular mineral In the flotation pulp. The reagents which will generally optimize the flotation process are commonly classified Into three distinctive categories: collectors frothers and modifiers. Large tonnages of metal sulphide concentrates which are the source of most of the common base metals are produced economically by fairly standard flotation techniques. The advent of modern technology coupled with the necessity of processing finely disseminated and complex ores of low grade has Increased the need for utilization of non traditional and high selective chemicals reagents for the economic recovery of metals and raw materials. Mining operations in developing countries continue to progress at a rapid growth as many countries mine and process both metallic and nonmetallic ores. The total mine production of base metals, precious metals, Iron ores and coal In developing countries In Africa, Asia and South America has been much higher as compared to the western world production In terms of tonnage and dollar value. Global capital Investments In mining during 1991-95 Is $ 55.1 billion and It Is anticipated that the development of new and specialty reagents may be concentrated In the processing of aluminum , copper, precious metals and Industrial minerals with special reference to potash, phosphates, kaolin and silica sands.(1) The challenge for the design and development of new specialty chemicals Is dependent on Its cost performance and environmental acceptability. Information on the theory and application on the development of mining chemicals has been reviewed In several conference proceedlngs,(2-4) publications(5) and also discussed by several Individual authors.(1,6-10) These publications serve as a comprehensive reference source on the reagents used In several flotation processes. This paper discusses the present trend in the use of specialty mining chemicals In diversified mining operations on several mineral systems with particular reference to sulfide ore systems. The necessity to expose these specialty chemicals through aggressive marketing techniques In mining operations In many developing countries Is also presented. SPECIALTY CHEMICALS Specialty mining chemicals, like other specialty chemicals, share common business characteristics that transcend geographic boundaries. They are manufactured 1n a few selected areas, generally expensive relative to commodity chemicals, shipped and compete globally and usually require specialized knowledge for proper use. Specialty mining chemicals are relative newcomers to chemical markets. The vast majority of mining chemicals are derived from products that are less than two decades old. Traditional collectors and frothers have been available for a considerably longer time. The emphasis on adding value to existing products and byproducts Is responsible for several characteristic features of the mining chemicals business. Most raw materials for these chemicals are related to oil and gas byproducts, chemical refineries, pulp and paper mills and all chemical manufacturers. Until the last several years these operations were located In Industrialized countries, while a significant number of mining chemical users were In developing countries. Therefore International trade In mining chemicals developed through agencies or agents in each particular country.

Jan 1, 1993

By H. X. Li, A. Correa, M. M. Zhang, W. Xuan, M. Andrade

"With increasing demand for steel and depletion of high-grade iron ore deposits, more research efforts are being directed toward extending the life of existing ore reserves and developing technology to treat low-grade iron ore resources. Among all the reported technologies, biotechnologies in mineral processing – specifically bioleaching and microbially induced flotation – have emerged to be considered as low-cost, environmentally friendly potential alternatives to many of the current mineral processing techniques. This paper provides a comprehensive review of current research on the use of microorganisms for iron ore beneficiation and, further, discusses the applicability of bioleaching, bioflotation and bioflocculation for the beneficiation of low-grade iron ores.IntroductionIncreasing global demand for raw materials has led to diminishing resources of high-grade iron ore. As a result, the mining and utilization of low-grade hematite, limonite, specularite, siderite and goethite ores have attracted more and more attention. However, these types of iron ores are of complex paragenesis and fine disseminated grain size, and often contaminated by phosphorus in the form of solid solution. The distribution of phosphorus throughout the iron mineral crystals prevents the effective use of physical separation techniques, and these complex ores are at present largely untapped due to a lack of cost-effective and efficient processing methods. Chemical leaching and roasting-magnetic separation approaches have been mainly tested only on the laboratory scale and are all either cost prohibitive or ineffective when used on low-grade complex iron ores."

Jan 1, 2015

By V. Kecojevic

The objective of this research was to establish the relationship between production, consumption and energy cost in the surface mining of bituminous coal. Specific energy sources such as diesel, gasoline, electricity, explosives and bituminous coal were considered in this study. Gain in net energy, proportion of the cost of energy consumption and total energy cost relative to total revenue of extracted coal were determined, and a new energy efficiency index and a new energy-cost ratio were established. A case study on an operating surface coal mine was carried out to demonstrate the application of the newly developed method. The results of this study can be used by the mine operators in establishing strategies for the optimization of energy production and consumption, and for reducing the cost of bituminous coal extraction.

Jan 1, 2014

By Karl C. Dean

The current emphasis on environmental problems has focused attention on the massive nationwide accumulations of mine, mill, and smelter wastes that represent potential air and water pollution hazards. The pollution hazards can be reduced or eliminated by utilization or stabilization of these wastes. The U.S. Bureau of Mines, since the inception of the Solid Waste Disposal Act of 1965, has been conducting research to determine the practicality of various utilization and stabilization procedures. Investigations include partial extractions of desirable waste components and full utilization of the wastes as simulated soils or in ceramic or other structural products. Chemical, vegetative, and combined chemical-vegetative methods of stabilization have been actively studied. This report updates information previously developed by the Salt Lake City Metallurgy Research Center and presents the current status of antipollution solid waste work 1/,2/.

Jan 1, 1970

By Glenn E. Hoffman

Relax: the world today is not running short of many mineral commodities, even though prices are spiraling upward. Einstein?s observation still holds true that everything is still relative, as long as one can pass on the incremental costs of production to the consumer. However, a strong consensus exists among many of the companies comprising the minerals processing industry that it is becoming increasingly difficult to find the easy-to-mine, high-quality resources that make juicy profit margins, which shareholders like. For the most part, the resource cherries have all been picked, and established mineral processing companies that are exhausting their reserves, or in the process of looking to add reserves so as to create longevity for their company, have no recourse but to look long and hard at what were once considered the dregs of the earth. Even end users, such as steel companies, are now looking to become ?miners,? to establish captive iron ore resources. Owning a captive resource facilitates a dependable supply of feed materials, which translates into effective cost control and a guarantee for a thriving sustainable business in the future.

Jan 1, 2012

By P. J. Arps

Cyanide (CN) is used to recover gold from its ores in many locations worldwide. In spite of the established history of gold mining in Alaska, modern cyanidation methods have been used at only one location, the Ryan Lode Mine at Ester Dome, near Fairbanks. Ore was processed by heap leaching between 1987 and 1989, when permitting issues caused operations to be terminated. Those issues have since been resolved, and plans to reopen the mine are currently being discussed. Plans are also proceeding to develop several other ore deposits in the state, all of which include the use of cyanide for gold recovery [6]. Since tailings and effluent water produced from these mines will require treatment, it is important to develop detoxification methods suitable for the Arctic and sub-Arctic conditions found in Alaska. Several methods exist for removing cyanide from mining wastewater. However, most industrial users prefer chemical treatment systems, and typically use sodium hypochlorite, hydrogen peroxide, or sulfur dioxide/air/copper to oxidize free and complexed cyanides [9]. Biological treatment has been used successfully at two sites in the United States [30,32] and field tested at several others [20,27,28]. In addition, one mine uses "natural processes", which include natural oxidation, photodegradation, and degradation by naturally occurring bacteria [33].

Jan 1, 1994

By Praterm J. D.

The process parameters for effective utilization of nitric acid as an oxidant for copper-iron sulfides have been developed. Leaching variables found to be important were acid concentration, temperature, time, atmosphere, pressure, mineral type, particle size, and percent solids. Particular attention was devoted to analysis and control of fumes evolved during the oxidation. Responses recorded were metal extraction, elemental sulfur formation and oxidation, product gas composition and evolution rate, reagent consumption, and residue flotation response. The paper concludes by laboratory testing a flow sheet based on the above observations. Ninety-eight percent of the copper contained in a chalcopyrite-bornite concentrate was recovered, requiring 1. 6 pounds of nitric acid to be regenerated externally per pound of copper extracted. Iron remained in the leach residue as hydrogen jarosite and was ultimately rejected from the system by froth flotation. Sixty percent of the sulfur contained, in the heading concentrate reported in the elemental form; the remainder was oxidized to sulfate and eliminated with the hydrogen jarosite in the flotation tails or by neutralization of the solvent extraction raffinate with lime. Nitrogen was evolved primarily as NO and NO2; up to 3 percent N2O was also present. Gases containing sulfur were absent except when pyrrhotite was solubilized in the absence of soluble copper. In this case, H2S was evolved.

Jan 1, 1972

By S. I. Freedman

Coal-oil mixture (COM) combustion technology is regarded by the Department of Energy as near term, and potentially applicable to existing utility and industrial steam generators and for injection into blast furnaces. From work done previously, it has been established that COM can be burned in existing boilers, into blast furnaces. Therefore, the issues being addressed by the current DOE program are: (1) determination of best available technology to achieve environmentally-acceptable long-term reliable operation and (2) determination of applications for which COM can be utilized economically. Some of the technological options have begun to be determined by projects already under way. However, many projects are still in the early stages of development.

Jan 1, 1978