Search Documents

By K. Burke, K. L. Myers, R. Espell

Barrick's Goldstrike AA heap leach pad is an HDPE-lined facility that was used for gold recovery from low-grade ores using conventional cyanide heap-leach technology. The pad was operated from 1987 through 1999. Goldstrike prepared a unique reclamation plan for the AA leach pad facility to provide for a cost-effective, environmentally sound facility closure and to fulfill the State of Nevada's closure requirements. The traditional Nevada leach pad closure procedure involves rinsing to reduce the cyanide concentration to an acceptable level followed by reclamation. However, rinsing does not typically reduce certain metals and compounds, and some constituents may increase in concentration with rinsing. A closure scenario to effect limited infiltration through installation of a capillary cover for the leach pad was developed. The capillary cover was constructed by placing a fine-grained layer above the coarse-grained spent leach material to create a capillary break. In an arid climate such as in Nevada, the fine-grained layer will rarely reach saturation, and the cover will be able to store water during precipitation events and will allow removal of water through evaporation and transpiration (ET) during the growing season. A 1.22-m (4 ft) cover thickness was selected as the optimum design cover thickness. The drainage network on the surface of the recontoured AA heap leach pad was specifically designed to enhance the re vegetation, reclamation and sediment yield control aspects of the AA heap leach pad closure, while resulting in a natural looking surface that is compatible with the surrounding topography. Adjacent natural topographic features were used to establish target design parameters for recontouring and erosion-control design.

Jan 1, 2002

By Neel Gupta, Brijes Mishra

Coal mining activity disturbs the natural equilibrium of in situ stress state such that the induced stresses deform the surrounding rock mass. Although the installation of roof supports typically prevents rock deformation, rock mass failure may still occur in bolted roof. The erratic failure of rock mass after few days to months and years of excavation is the result of time-dependent deformation of roof rock under constant surrounding stresses. In the current research, the triaxial laboratory creep experiments proved that Marcellus shale exhibits time-dependent deformation under constant stress that was smaller than the failure strength. However, unlike conventional experimental results, the time-dependent deformation did not depend on the level of constant stress. The often-neglected initial state of specimens and intrinsic heterogeneity highly influenced the time-dependent failure of Marcellus shale.

Jul 27, 2021

By E. J. Haas

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health. ABSTRACT Leadership is a critical component to an organization’s safety culture and influences the ways that health and safety is enacted on site. Therefore, it is not surprising that improving leadership will also improve safety. Worker perceptions of management practices are shaped through unique leader-employee interactions over time. However, few details are known about the communicative support (i.e., emotional, informational, and tangible) offered by supervisors and its impact on miners’ perceptions and performance. Using pre and post-interview data with 20 supervisors and 48 workers during six-week interventions, researchers identified positive and negative instances of supervisor support and its implications on worker performance. This paper highlights the common support tactics offered by supervisors and desired by workers to help practitioners identify ways to improve their safety culture and subsequently, the proactivity and compliance of their workforce. INTRODUCTION Supervisory leadership is a critical component to the effective implementation of an organization’s health and safety management system (HSMS). Specifically, supervisors serve as representatives of an organization and their actions are indicative of the organization’s safety culture (Eisenberger et al. 1986). Senior management has been shown to serve as a frame of reference for guiding safe behaviors in the workplace (Mearns et al. 1998) and, more recently, research has related supervisory enforcement to workers’ safety compliance (Petitta et al., 2017). Therefore, it is not surprising that by improving leadership, perceptions of management and subsequent safety outcomes are likely to improve as well (Zohar, 2002). Perceptions of management are shaped through unique leader-employee interactions over a period of time (Hofmann and Morgeson, 2004, 1999). How these unique interactions impact worker performance, however, remains unexamined. As a result, understanding how supervisor-employee relationships operate in high-risk environments is unclear (Mirza and Isha, 2017; Denis et al., 2010). A starting point to better recognize the idiosyncrasies of these relationships is by way of examining the communicative support offered by front-line management and received by industry workers. To this end, this paper uses pre- and post-interview data to study the communicative aspects of supervisor-employee interactions at mine sites. The analysis uses a social support framework to identify positive and negative instances of supportive communication. From interview data with 20 managers and 48 mineworkers, data emerged that shows how supervisors’ unique types of support contribute to workers’ perceptions, motivation, and follow-through of safe work behavior.

Jan 1, 2019

By A. G. Yapo, T. W. Camm

"All-in sustaining cost is a metric used by mining companies to reflect the cost of gold mining in a consistent format useful to both investors and mining professionals. Cost reporting focused on the direct cost of mining and processing ore was summarized in the non-GAAP cash cost developed by the Gold Institute in 1996. In 2013, a group of mining companies, working with the World Gold Council, developed a more inclusive approach to reporting costs designed to solve the dilemma of showing a more comprehensive reflection of recurring costs involved in producing gold, without discouraging investors. INTRODUCTION Mining today plays a key role in the development of our civilization as a source of essential raw material and provider of essential fuels, producer of jobs, and a factor in support of the international balance of monetary payment (Camm, 2014). Professionals in mining locate, develop, design and manage ore deposits in an environmentally safe and profitable manner. As mineral deposits become increasingly scarce, new challenges face the industry. A current trend is to an increased emphasis on underground mining techniques for deeper deposits. Operations are safer today than before as companies understand better their work environment and the importance of mining responsibly. A continual challenge for the industry is accurately reflecting the costs and selling price of ore. An enduring characteristic of mining is the situation where the market typically determines the price of a commodity; the main control a company has on the bottom line is to control the cost of production. An attempt to bring light and clarity on the cost of their business will give a better idea to investors on the true profitability of the mining business. Gold producers face this struggle to accurately reflect the cost of production while also seeking to attract the interest of the investment community (Hill, 2013). In order to have a consistent format to report on their production costs, leading gold producers through their alliance inside the World Gold Council (WGC), worked on the adoption of a new cost framework: the All-in Sustaining Cost (AISC) and All-in Cost (AIC). Since 1996, the traditional cash cost reporting has focused only on the mining and processing costs incurred in mining an ounce of gold, which included the costs of goods sold (labor, energy, and consumables costs) and royalties (Table 1). But cash cost reporting ignores many important aspects, like sustaining capital, general and administrative expenses, and site rehabilitation at the end of the mine life (Whelan, 2013). The cash cost was used to attract many investors into the business. In fact the high gross margin (sales minus cash costs) has been promoted the past decades by the industry instead of the net or operating margin. As a result, even when the gold price was high, nearly $1900 per ounce in August 2011, gold producers were not reporting excessive profits in their cash flow / income statements, to the disappointment and incomprehension of investors (Milstead, 2014). The truth was simply that the other costs omitted in the traditional cash cost were reducing the apparent profits."

Jan 1, 2017

By J. Kallioinen

Flotation of low grade Ni ores with serpentinite host rock tend to yield low recoveries of Ni With high MgO contents in the concentrate. The recovery can be enhanced by optimizing the sub-processes in the pulp and in the froth. The new OF-100 flotation cell has been designed to be adaptable to different feed fineness (Coarse, Fine). The losses can according the research conducted at Outokumpu's Hitura plant be substantially decreased by OF-100's new rotor and stator design and froth zone geometry. The froth residence time is used to adapt for feed particle size changes measured by the Outokumpu PSI- 200. Models for the behaviour of different particle Sizes in the sub-processes have been developed. The modified froth zone geometry and the capability of maintaining a froth of desired thickness allows efficient washing of the obtained concentrate producing low levels of MgO.

Jan 1, 1994

By Yousef Ghorbani, Abolfazl Danesh, Fatemeh Kazemi, Ataallah Bahrami, Morteza Abdollahi, Mohammad Raouf Hosseini

This study aims to investigate the effects of operational variables on concentrate grade, recovery, separation efficiency, and kinetic parameters of the copper flotation process. For this purpose, the effects of the pulp solids content, collector and frother dosage, and preparation and concentrate collection time were studied using a Taguchi experimental design. The results of statistical analyses indicated that the concentrate collection time and pulp density were the most influential parameters on concentrate grade. Considering copper recovery, concentrate collection time, collector dosage, and pulp density were the most significant variables, in decreasing order of importance. Also, the separation efficiency was mostly influenced by the concentrate collection time. Furthermore, kinetic studies showed that the second-order rectangular distribution model perfectly matched the experimental flotation data. The highest kinetic constant of 0.0756 s−1 was obtained from the test, which was performed with 35% solids content and 40 and 20 g/t collector and frother, respectively. The highest predicted copper recovery of 99.57% was obtained from the test at 30% solids content, and the collector and frother dosages of 40 and 15 g/t, respectively

By M. Spangler

FirstMiss Gold installed a supervisory control system based on Pavilion Technology's Process Insights neural network software and Oil System's PI data historian. The primary goal of the system was to control the acid preconditioning circuit. However, our first successful control loop was on the limestone feed rate to the neutralization circuit. The information gained by modeling these circuits and the better control provided by the system has resulted in reagent savings of over $80,000 per month.

Jan 1, 1995

By M. Sandin

According to the world bank1, the mining industry consumes up to 11 percent of global energy use. In comparison, 70 percent of mining projects from the six largest mining companies operate in water-stressed regions. To steer the direction of the process industries toward more sustainable practices, more than 40 governments have adopted a price on carbon. This measure includes additional taxes on the use of fossil fuels, trade programs, new standards for renewable energy, energy efficiency mandates, more stringent emissions regulation, carbon offsets, etc. This emphasis is also supported by investors shifting their priorities to reduce risk by focusing on long-term plans, including environmentally friendly operations. The metals and mining industry is at the core of the green energy mix and electrification of vehicles. This new trend creates an astronomical increase in demand for minerals. Under a 2-degree scenario, according to the latest analysis from the world bank, as new energy technologies continue to grow, it is expected that all minerals to double in demand, and the distribution of these materials will depend on their application. • Solar panels, will account for 87% of the aluminum demand, and more than 95% of silver • Wind turbines and geothermal plants will require 98% zinc and 64% titanium. • Solar and wind energy alone will demand more than 74% of the global supply of copper, and this is without considering wiring or other infrastructure to connect the grid • Battery storage accounts for 100% of the graphite and lithium demand. (Hund, 2020) • Other materials, such as nickel and steel, are also projected to more than double in demand as they are cross-technology minerals. These materials require a manufacturing process that is accountable for the emissions proper of the transformation process. It requires that these processes move from a hindsight mode focused on reporting to a forecasting mode based on run-time measurement of GHG emissions. This is a critical first step in companies realizing an economic return for doing the right thing for the environment and their communities.

Feb 1, 2023

By Kenneth R. Hancock

The importance of "Mineral Pigments" can best be shown by noting that the world production is estimated to be in excess of 47 billion kilograms (52 million st). This quantity if pack- aged in the common 22.6 Kg (50 Lb.) bag and placed end to end would circle the world over 500 times. This world production figure is based on a broad concept that pigments, extenders, and fillers have essentially similar functions. In this paper mineral pigments are products produced synthetically or from selected minerals and through pulverization have characteristics of pigments.

Jan 1, 1985

By Bob Munz, Ry Stone

To facilitate the installation of the longwall equipment for each extraction panel, West Elk mine develops set-up room roadways that are between 26.5 and 30.5 feet wide. Historically at the mine, the set-up room roadways have been driven in a single 20-foot-wide pass, then incrementally widened to the required width during installation of the longwall shields. The first pass roof is supported with a generic roof support plan consisting of partially encapsulated roof bolts and point-anchored cables. This ground support plan was utilized regardless of the geotechnical conditions encountered in the roadways or consideration of the required stand-up time of the roadway before the longwall shields were installed. This "blanket" approach tends to result in over-conservative or inappropriate roof support designs, particularly in changing geotechnical environments. Guided by the desire to optimize the ground support plans and increase mining efficiency for future set-up rooms, the West Elk mine and Agapito Associates, Inc. have developed and implemented a strata management program. Strata management, as a formal and structured process, allows ground support and mining methods to be tailored to the anticipated and encountered geotechnical environment in a con- trolled manner (Thomas 2007). To arrive at adequate site-specific ground support plans for the set-up rooms at the mine, several struc- tured processes were utilized. Firstly, the geotechnical environment was characterized by examining the roof lithology and geomechanical properties from nearby rock core obtained from exploration boreholes. To increase both mining efficiency and continuity, and to achieve longer stand-up times before the longwall shields are installed, a multi-pass approach was implemented into the design. During mining, the geotechnical conditions of the roadway are mapped, and the roof is strategically surveyed with a borescope. This process was used to ensure that the encountered ground behavior was in alignment with the design standards used for the roof support design. To support this process with measured data, roof extensometers were strategically installed throughout the roadway. This data was used to monitor the magnitude of roof displacement at various horizons and record displacement rates up until the longwall shields were installed. Lastly, a Trigger Action Response Plan (TARP) was used during mining to cater for any unforeseen changes in ground conditions that would warrant additional con- trols such as increased monitoring or the installation of additional ground support. This paper presents two case histories at the mine where the above strata management approach was implemented to arrive at a site-specific ground support plan. The main changes to the mine's ground control plan included a multi-pass mining approach, the utilization of fully encapsulated roof bolts, and the transition to a stiffer roof support system. The geotechnical mapping, the roof borescope results, and the roof extensometer data will be presented to demonstrate the effectiveness of the ground support system up until the longwall shields were installed in both presented cases.

Jun 25, 2024

By J. Andres

"Freeport-McMoRan’s Sierrita operations refines molybdenum disulfide in a ferric chloride leach to remove impurities. To understand bottlenecks in the leach process and the true capacity of the leach system, a cross-functional team was established to look at theoretical models, kinetics of the leaching process, equipment limitations and operational strategies. A series of in-plant tests were run which resulted in a road map for improved throughput. INTRODUCTION Molybdenum, a vital component in the steel industry, is often found in nature as molybdenum disulfide (MoS2). Molybdenum disulfide deposits can exist as standalone components in an ore body, or can also be found within copper porphyry nodes. Processing for these copper/molybdenum porphyry ore bodies involves a first stage of flotation to produce a bulk concentrate before separation of the copper and molybdenum concentrates in a second stage of flotation. In this second stage of flotation, a reagent is added to suppress the copper particles, while allowing the molybdenum disulfide particles to remain hydrophobic and continue to float. This separation is very good at keeping the molybdenum out of the copper concentrate; however a portion of the copper continues to float through the circuit. As a result, there is typically some amount of copper in the final molybdenum concentrate. This copper must be removed in order for the molybdenum disulfide product to meet product quality specifications. Once the raw molybdenum disulfide product has been made, a separate process must be applied to remove any copper, lead, or other impurities remaining in the concentrate. This process usually involves the selective leaching of impurities out of the bulk solid. Gupta mentions three specific types of leaching agents, sodium cyanide, ferric chloride, and hydrochloric acid for the removal of sulfide impurities. Sodium cyanide is useful for the removal of copper compounds such as bornite, covellite, and chalcocite.1 Sodium cyanide solution dissolves these copper compounds, and the remaining molybdenum solids are filtered to produce a pure molybdenum concentrate. Ferric chloride works similar to that of sodium cyanide, but is particularly efficient in removing chalcopyrite and galena compounds. These compounds are easily chlorinated at elevated temperatures, producing copper chloride and lead chloride, through the reactions presented below:"

Jan 1, 2015

By C. Dirscherl

"Declining ore grade, leading to increased material transport and plant throughput requirements, is one of the major challenges in the current mining environment. This is accompanied by rising energy and labor costs, decreasing plant productivity and the requirement for highest plant availability. Siemens’ answer is the latest gearless drive technology for grinding and conveying. Gearless drive solutions are surpassing the mechanical limits of conventional drive systems serving to utilize the principle of economies of scale. By elimination of various components of the drive train the maintenance activities and spare parts inventories are reduced. The advantages are culminating in the incomparable availability of the Siemens’ gearless drive technology of 99.46 to 99.71% - as confirmed by real operational data from the Antapaccay mine in Peru. It was the first plant worldwide to use gearless drives for both applications. KEYWORDS: Gearless Mill Drives, Gearless Conveyor Drives, Availability, SAG Mill, Ball Mill, Overland Conveyor, Antapaccay INTRODUCTION – THE GEARLESS PRINCIPLE The principle idea behind a gearless drive system is to reduce the number of components and diversity of parts. Especially those components that are at the edge of current manufacturing or power limits are eliminated. The used equipment provides the possibility to scale up and increase the power transmitted to the driven machine. This finally results in a possible increase of throughput respectively transported or processed material. In order to apply this principle of simplification we will take a look at the components of a conventional drive system consisting of: - Driven equipment (mill, conveyor, slurry pump…) - Components altering the rated speed (gearboxes, girth gear / pinion) - The electric motor - Starting devices for the motor (VSD, CCV, LRS, clutch…), which are necessary because a direct across-the-line start of high power motors with load would result in a significant drop in the line supply voltage - Alternatively a variable speed drive (VSD) or cycloconverter (CCV) to utilize the possibility of speed variation during operation - The electrical supply system (cables, switchgear, transformers, protection equipment) Intermediate gearboxes are not required when a motor is used with a rated speed that directly matches the speed requirement of the driven equipment. Furthermore the VSD can be used to smoothly start the motor and to vary speed during operation, which means that it satisfies both requirements."

Jan 1, 2015

By K. Witt, S. Steinlechner

In different nonferrous metal-producing industry sectors, the impurity element iron has to be removed from the process solution. Examples for the arising residues are jarosite or goethite precipitates from nickel or zinc production but also red mud from aluminum production. Regardless of environmental concerns, the material is landfilled in almost any case, although valuables such as indium, silver, nickel, or zinc are present in considerable amounts. Within the presented research, a low carbon dioxide emitting multi-metal recovery from such iron-containing residues by means of a selective chlorination extraction has been fundamentally evaluated by experiments but also by comprehensive thermodynamic calculations. The paper summarizes the thermodynamic fundamental concept exploited to separate the dominating iron matrix from the valuable elements and shows verification experiments in a lab size of several grams. Through thermodynamic calculations and smallscale experiments with pure metal oxides and sulfates, it has been proven that the metal chlorides AlCl3∙ 6H2O, FeCl3∙ 6H2O, and MgCl2∙ 6H2O are viable and effective reactants for chlorination. In trials with actual industrial iron precipitation residues from the zinc industry, especially, the use of MgCl2∙ 6H2O and FeCl3∙ 6H2O leads to high extraction rates for the investigated valuable metals Ag, Au, Bi, Cu, In, Pb, Sn, and Zn.

Nov 14, 2023

By A. Datta

An appropriate scale-up methodology is very useful for ball mill design and optimization of the grinding circuit. To date, the scale-up is based on the selection and breakage function model using lab mill data. However, a major drawback of that approach is that the charge motion in a lab mill is vastly different from that in a large industrial mill. Therefore, in the methodology proposed here, first the energy of individual collision in the mill is computed employing the discrete element method (DEM). Then the breakage of particles as a function of collision energy is studied in a separate experiment. Together, this information constitutes what is known as collision energy based population balance model. The appropriateness of this model is shown for different batch grinding mills.

Jan 1, 1999

By M. Javier

In business mining, dilution is the result of the operating parameters that occur too often and cause serious consequences to mine performance, questioning TO WHOM BENEFITS DILUTION. Mining persists in changing perception of real meaning of dilution. The lack of interrelation between mineral processes and nature compromises the understanding of dilution; this absence of interrelation occurs due to the misinterpretation of nature, otherwise, Geomimic could be helpful to filling the gap of misinformation. NATURE provides LIMITED metals in low content deposits; it is a challenge to obtain them. Nature never considers dilution. Furthermore, though dilution is a human concept, dilution is accepted and promoted. Reality of dilution is in its errors accumulation that translates into technology level or status applied in nature. It is doubtful that dilution can continue surviving if it is ?meaningless?. It will discourse: Is dilution illegal? If the change occurs in the prediction of mining will prevail a different destiny, it is important to touch the cores of the business; otherwise, it would represent repetition of the same ?negative? effects, as usual. Mining defines many losses during the disturbance of nature, from NPV elaboration to the metal recovery to commerce, demanding BETTER DESIGN. This paper introduces and applies MANAGEMENT BY LOSS, as first steps, to limit risks and uncertainties in mining. As result, the management of dilution will be obtainable under mining practices which promotes its character of SUSTAINABILITY.

Feb 23, 2014

By J. Casado

This paper presents the results of an analysis and summary of relevant literature on the mechanism of cementation of metals in acidic aqueous media, with the aim of reconsidering the conventional assumptions. The simplicity of the process as a mere galvanic metal displacement is discussed, and the real effects of pH and hydrogen pressure in different cases assessed. Finally, an alternative mechanism scheme with respect to the role of hydrogen species, in agreement with reported data, is proposed.

By S. K. Kawatra

It is common in coal-cleaning operations to produce a fine waste stream which contains a considerable amount of coal, but which is not economical to recover both because it is mixed with large amounts of difficult-to-remove clay slimes, and because the fines are often heavily oxidized. Conventional froth flotation machines cannot produce an acceptable product from such material in a single stage of flotation, and even flotation columns often have difficulty cleaning this type of feed. A new type of flotation column was designed specifically to deal with these problems, and was installed and tested in a coal-cleaning plant in Ohio. The feed coal contained 39.8% ash as fine clay, and 2.83% total sulfur, and was 80% passing 176 micrometers. The coal was a thickener product which had oxidized for some time, and was very difficult to float. However, using the new column it was possible to recover up to 85% of the calorific value in a product containing less than 11% ash, and up to 60% of the calorific value in a product of less that 8% ash. The bulk of the pyritic sulfur was rejected from the coal as well. Multistage flotation tests showed that the flotation column was able, in a single stage, to produce the best froth flotation product that it was possible to recover from this coal.

Jan 1, 1994

By R. P. Gardner

Results of work on the development of a phenomenological model for the continuous flotation process using short-lived radioactive tracer techniques for the determination of model parameters is reported. A model that incorporates a flotation first-order rate constant and a residence time distribution based on the cross flow finite state (CFFS) model has been derived and investigated. The short-lived radioactive tracer techniques necessary to extract the model parameters have been developed as have the necessary nonlinear search methods. The conditions under which all the model parameters can be extracted from a single radiotracer experiment are detailed and illustrated. A microcomputer-based unique data logging system has been designed, assembled, and implemented for collecting the necessary transient radiotracer data. Results are reported for a continuous laboratory flotation system for the two systems mica ore and coal.

Jan 1, 1985

By Serdar Aktaş, Özgün Küçükoğlu, Burcu Nilgün Çetiner, Mehmet Hakan Morcalı

This study compares the cementation performance of metallic iron, metallic aluminum, and metallic tin in terms of the reaction conditions and parameters in synthetic antimony chloride solutions. The effects on the antimony recovery (%) caused by the cementators’ types, stirring speed, reaction time, and temperatures were explored thoroughly. The cementation kinetics of antimony were also explored for each cementator. The activation energies were determined to be 10.99, 9.09, and 13.58 kJ mol– 1 for Al, Fe, and Sn, respectively. The results reveal that the reaction is diffusion controlled, and comparable results were obtained for each cementator. At 25 °C, 40 mg of iron powder was found to reduce all antimony ions (i.e., approx. 99% recovery), but even when 100 mg of Al and Sn cementators were used, the antimony recovery did not reach 100%. This result shows that iron is the best candidate to cement antimony out of the solution.

Jan 28, 2022

By Kevin Andrews, SETAREH GHAYCHI AFROUZ

Ground control analysis and groundwater inflow assessments for underground coal mines require in-depth field investigations including, but not limited to, geological and geotechnical core logging, downhole geophysical logging, laboratory rock strength testing, and packer (Lugeon) testing. Field and laboratory data collection are time consuming and expensive, and an initial understanding of the expected trends among various geotechnical and hydrogeological parameters can assist with the planning and optimization of geotechnical characterization studies and grouting plans. In this study, a comprehensive database is analyzed, comprised of important rock mass characteristics (hydraulic conductivity, rock quality designation (RQD), and lithology) for coal-bearing rocks in the Central Appalachian Basin. Statistical analysis of the data is completed to establish an enhanced understanding of geotechnical and hydrogeological conditions expected to be encountered as underground coal mining passes near and beneath streams and rivers. The results of the study provide valuable reference material for the coal mining industry for completion of shaft installations, mine stream crossings, environmental assessments, and grouting and mine dewatering designs.

Jul 1, 2023