Search Documents

By J. G. Groppo, T. L. Robl, C. J. McCormick, W. M. Lewis

The combination of froth flotation and hydraulic classification can facilitate the production of a high-quality pozzolan that meets or exceeds ASTM specifications. This combination has been rigorously evaluated and results of pilot-scale testing are presented. Pilot-scale testing was conducted on fly ash from two active electric utility storage ponds. The tests demonstrated that a high-quality and consistent pozzolan could be produced using Advanced Pozzolan Technologies' Fast Float™ Process. Along with the pozzolan, the additional production of aggregate for masonry mortar and the production of a low sulfur, medium-Btu fuel were also demonstrated. The Fast Float™ Process incorporates several simple unit processes to ensure pozzolan consistency. Classification controls the particle size distribution, which is critical for achieving early strength;flotation controls the grade with respect to L.O.I.; and dewatering controls the moisture content.

Jan 1, 2000

By John Ralston, Gayle E. Morris, Daniel Fornasiero

The interaction of talc with carboxymethyl cellulose, a polymeric depressant currently used in the mining industry, was investigated. adsorption isotherms, infrared spectoscopy and microflotation studies were performed to determine the surface properties of the depressant at the talc-water interface. Solution conditions were varied in ionic strength, pH and the presence of magnesium ions. The adsorption of the anionic polyelectrolyte, carboxymethyl cellulose onto the talc surface was greatly influenced by the solution ionic strength and pH. Limited adsorption, and therefore depression, occurred at high and low ionic strength. Adsorption, and thus talc depression, improved greatly with either increased ionic strength or reduced pH. With the addition of magnesium ions, talc depression was shown to improve considerably. The improved depression is likely to be the result of the formation of a magnesium ion-carboxyl complex.

Jan 1, 1995

By S. K. Kawatra

Various types of mathematical descriptions of the flotation process are used in the design of a full scale flotation circuit. Mechanistic descriptions developed under controlled laboratory conditions establish theoretical residence time requirements. Empirical models, describing flotation performance as a function of full scale operating variables, are established from one flotation system and applied to another hypothetical system. Problems of design by mechanistic modeling, such as scale up factors, can be alleviated if the model is developed from a full scale flotation circuit. However, the numerous uncontrollable variables encountered in a full scale operation would preclude the practical application of such a model. Incorporating empirical relations into the full scale mechanistic model will facilitate its effective use as a guide for flotation circuit design. A semi-empirical model has been developed that promises to offer a more effective means of flotation circuit design.

Jan 1, 1982

By H. Ouellet, J. Paraszczak

The pneumatic jackleg drill remains a widely used tool in development and production drilling in many small-scale and narrow-vein underground mining operations in North America. Several drawbacks of this technology (unsatisfactory drilling rate, noise, vibration, presence of oil mist, etc.) and the successful introduction of water-powered jackleg drills in South Africa have stimulated the interest of many mine operators. The performance of both drill types have been tested in a mine site in Northwestern Quebec, Canada. Results of the testing of penetration and advance rates as well as environmental aspects are presented. They show a superiority of water-powered drills, even though the difference in performance is less significant than that reported from South Africa. Further research avenues are proposed to better evaluate the potential of water drilling technology in North American metal mines.

Jan 1, 1995

By Mel J. Laurila

The application of on-line ash analyzers in coal processing has become widespread. However, the analyzers are employed largely in monitoring, blending or sorting applications. Just recently has work begun on using on-line ash, moisture and/or solids data for plant control; and even more recently for localized circuit or unit operation control. Process Technology, Inc. (PTI) has since 1990 placed several bulk coal and slurry analyzers in practice where Fuzzy Logic Control (FLC) loops are used to manipulate controllable variables in real time. This technology is now being advanced by PTI. Unit operations where FLC has been employed in feedback loops using on-line ash analyzers include: heavy media vessels, cyclones, concentrating tables and froth flotation. The design, implementation and improvements attainable in preparation plant control using on-line ash analyzers are outlined in this paper.

Jan 1, 1995

By W. Pariseau, J. Goris, S. R. Dismuke

Ore at the Magmont mine in southeast Missouri is extracted by the room-and-pillar method on two and sometimes three horizons. In 1991, a plan was formulated to recover high-grade ore in pillars using cable halts to accommodate spans of more than 27 m (90 ft ). A test area was selected and a recovery plan developed. A cooperative rock mechanics study was established by Cominco Metals, the US Bureau of Mines and the University of Utah. When initially opened in 1968, the planned production rate was about 910 kt/a (1 million stpy). Due to declining reserves, the production rate was decreased in November 1992 to 570 kt/a (630.000 stpy). Pillar recovery now accounts for about 40% to 50% of the mined tonnage. This method plays a vital role in allowing Magmont to continue to operate.

Jan 1, 1996

By D. M. Cregger, J. L. Rosenblad, R. E. Ranken

The construction of a large span, high-walled underground opening in a low strength shale rock is unprecedented. The feasibility of constructing a pumped storage project with several tunnels and a large underground powerhouse in low strength shale rested largely on the feasibility of building stable openings large enough to accommodate the required equipment. Because of the lack of experience with large openings in shale, the decision was made to excavate a test adit and test chamber and conduct a multi-faceted geotechnical evaluation program designed to yield pertinent in-situ data on the ability of the shale to accommodate a large underground opening. Factors considered in the shape, size, orientation, and location of the test chamber were: (1) similarity to the anticipated powerhouse chamber, (2) nature of the most important data to be obtained, (3) feasibility of construction, and (4) economics.

Jan 1, 1983

By Wayne A. Ericson, Kirk S. Davis, Cornelis Winkler

BCI has developed a chemical process known as Ecophos® for the multi-industrial Pine Level Project in DeSoto County, Florida. Approximately 85 percent of the phosphogypsum at Pine Level will be converted to a very clean gypsum. The remaining 15 percent, including impurities plus some quartz tailings sand, constitutes what is termed redigestion solids. BCI has developed an alternative to the practice of disposing phosphogypsum in large above-ground impoundments. The proposed disposal method consists of mixing the redigestion solids with clays and reacting the mixture (leached tailings) with lime prior to disposal into the mine excavations as a reclamation soil material. Leachate water quality testing using lysimeter equipment indicates that the pore water associated with neutralized leached tailings meets maximum contaminant levels set for the drinking water standards of radium and selected primary metals.

Jan 1, 1992

By David C. McLean, Peter Penner, Martin de G. Salter

The Rogers Pass Project for C.P. Rail includes a 14.7 km tunnel and an 8.5m diameter concrete lined ventilation shaft to a depth of about 335m. The shaft collar is in bouldered water bearing glacial till to a depth of about 95m. Initial excavation in the overburden was with the aid of dewatering wells. When ground support problems arose the excavation was completed by a two stage freeze programme. Freeze holes were drilled from the shaft bottom. This most unusual method was successful in overcoming the difficulties safely and efficiently. The remainder of the shaft was sunk and lined conventionally. Finally, a central dividing wall was poured by jump forming from the bottom up. The wall was completed to a high standard at up to about 20 vertical metres per day.

Jan 1, 1989

By Pradip

The development of highly selective mineral processing reagents, which are not merely metal-ion specific, but specific to the particular mineral surface structure, is essential for the exploitation of relatively more difficult-to-process ore deposits, in particular for the separation amongst minerals having the same constituent ion. Both the choice of the functional group as well as the molecular architecture of the reagent determine its selectivity. Several examples are presented in this paper to illustrate the concepts of structure specificity and molecular recognition at mineral surfaces - the concepts crucial to the advancement of the emerging science of reagents design. Recent advances made in the understanding of molecular interactions involved in the synthesis of biomineralized materials are discussed so as to delineate the utility of this approach in the design of selective reagents for mineral separation.

Jan 1, 1994

By John R. Marks

Few if any mines in North America have used exhaust air to remove heat at temperatures above the stope reject temperature. In contrast, the South African mining industry has long taken advantage of this heat removal method. The Homestake Gold Mine in Lead, South Dakota, has reached the point where a large air-conditioning upgrade is needed. Since existing air and water resources are being utilized about as well as practically possible, it was recently decided to install an 8.1 MW(R) (2300 ton) plant in the deepest mining division. Two horizontal bulk air spray coolers will distribute the coo1th to active workings via controlled recirculation. The heat will be rejected to exhaust air in four parallel cooling towers. The number and size of these large direct-contact heat exchangers prompted an investigation into South African planning techniques.

Jan 1, 1987

By Robert C. Dunne, Maurice E. Freeman, Denis S. Yan

A laboratory tower mill was used to investigate the effect of some variables on the power requirements of a plant mill. The grinding laws were tested for fine grinding and Charles' law and Rittinger's law found to be most closely satisfy the experimental data. The effects of ball size, ball charge mass and media type were investigated. The screw speed was altered to control the power input as required. The results indicate that changes in these variables will change the grinding kinetics but in terms of the grinding efficiency they have no effect on the size-energy relationship. The main factor in the specific energy efficiency is the transfer of the input energy to the charge by variation of the agitation mechanism. The efficiency of a tumbling ball mill and a pin stirred mill were tested for comparison.

Jan 1, 1995

By D. O. Shah, K. C. Adiga

Flotation of coal after multistage addition of frother was found to yield coal fractions with significantly lower ash content as compared to the feed. Ignition and combustion characteristics of different coal fractions were evaluated using a differential thermal analyzer (DTA). A correlation between low ash content, low specific gravity, and high reactivity of coal was observed. It is suggested that in the ignition stage, removal of mineral matter enhances reactivity through the physical changes brought about by ash removal. A detailed analysis of pre-ignition kinetics indicated the possible effect of bulk density of coal in terms of resistance to volatile release and effective (available) surface area of coal. In the char combustion stage, mineral matter seems to influence reactivity through catalytic activity of surface concentrations of metal ions, ratio of combustible/non- combustible material, internal pore structure, and surface roughness.

Jan 1, 1988

By M. Schultz

The cost of remediation often drives the selection of the preferred remedial alternative at hazardous waste sites. The use of probabilistic cost/risk analyses can aid in predicting costs of remedial alternatives. Three types of information are discussed in performing cost/risk analyses: (1) data on the quantity of contamination versus the contaminant concentration; (2) unit costs of remediation for the remedial alternatives; and (3) risk to contaminant concentration relationships. Cost/risk evaluations are performed on a site-by-site basis, to account for combined risks of different contaminants and differences in quantity to be remediated versus contaminant concentration. The cost/risk analysis produces a graph of risk versus cost for each of the remedial alternatives. These costs are then compared to facilitate selection of a preferred alternative. An example of comparison of alternatives is illustrated for a historic coal gasification site.

Jan 1, 1992

By Raivo Maripuu

The Boliden Group encompasses Sweden's foremost operations related to the mining and production of copper, lead, zinc, precious metals and metallic by- products. It is also the dominant swedish producer of sulphur-based heavy inorganic chemical products and fertilizers and has an international trading organization covering, in adition to the group's basic products, industrial minerals and oil. Boliden's activities in- clude the marketing of proven Boliden technique and know-how. Boliden Metall - the mining and metallurgical company within the Boliden Group - produces about 13 million mtpy of ores at mines in northern and central Sweden. Boliden has, over the years, become a specialist in processing poly- metallic sulphide ores and its eight concentrators presently serve 15 mines. Boliden has a long history of close cooperation with Swedish and foreign manufacturers in developing new products and processes.

Jan 1, 1979

By Milton E. Wadsworth

Cost effectiveness in gold and silver leaching has centered mainly on reducing or preventing excessive use of lixiviants. In cyanide leaching practice, the active reactants, cyanide and oxygen, present different problems. The activity of cyanide may be adjusted at cost, but oxygen from air, has a fixed, low activity with an equilibrium concentration of ~7 ppm. Consequently, the use of air in agitation and heap leaching presents distinct kinetic problems. The refractory ores are either high consumers of oxygen or tend to immobilize dissolved precious metal-cyanide complexes. Commercial treatment of refractory ores involves oxidation by pressure leaching, roasting or biooxidation prior to cyanide leaching. Chemical reactions important in preoxidation of refractory sulfide ores by pressure leaching and biooxidation are considered. Major emphasis is given to the role of oxygen in heap leaching of oxidized ores.

Jan 1, 1995

By J. Y. Kim, R. W. Stanley, L. Rosato

Silver contained in zinc calcines undergoes several phase changes as it proceeds through the leaching circuit of a roast-leach-electrowin zinc plant. In this study, the flotation response of silver, from leach residues prepared under a variety of carefully controlled operating conditions in the pilot plant has been examined. Flotation of neutral leach residue is shown to be technically viable and to merit consideration for those plants without a high-acid leach circuit, but having significant silver values in the feed. Residue leach conditions must be kept slightly acidic to promote the formation of Ag2S, (AgCu) 2S and Ag2S rims on residual unroasted sphalerite, while simultaneously avoiding the hydrolysis of soluble iron, which depresses silver recovery and grade. Factors to be considered during integration of a flotation process into an electrolytic zinc plant are discussed.

Jan 1, 1992

By I. D. Lindley

The Wild Dog vein gold deposit in East New Britain Province, Papua New Guinea, forms part of a recently discovered 26 km zone of auriferous quartz vein mineralisation. The deposit, which was discovered in July 1983, has no silt anomaly, and a panned concentrate anomaly and float train restricted to within 500 m and 800 m respectively, of the discovery outcrop. Discovery of the Wild Dog deposit was a result of the methodical followup of regional panning which, as followup progressed, was replaced in importance by float sampling. Of the sampling methods used during the exploration leading to discovery, panning and float followup provided immediate indications of the presence of mineralisation. This high degree of spontaneity of followup is not provided by geochemical techniques, and has obvious advantages in high cost exploration for precious metal deposits in remote locations.

Jan 1, 1988

By Frank F. Aplan, Robert S. Thomson

A placer ore jig, typically used to recover fine gold, tin and diamonds from alluvial ores, has been modified to remove fine pyrite from minus 6.4 mm (-114 inch) coal. In parallel tests, it proved to be far superior to two conventional coal jigs, the Baum and the Baum-feldspar, in removing fine pyrite from coal. The Pan-Am placer jig was found to remove essentially all of the +28 mesh pyrite and from 99% to 90%, decreasingly, in the 28 to 200 mesh range. This jig also showed a superior performance to the Baum-Type jigs in removing fine coal from its associated refuse. The superiority of the Pan-Am placer jig is related to the strong emphasis given on the suction stroke and, hence, on consolidation trickling, whereas the Baum jigs principally emphasize the pulsion stroke during jigging.

Jan 1, 1995

By J. D. Miller, C. L. Lin

The appropriate software and hardware necessary to adapt an X-ray CT analyzer for the determination of coal washability was developed and successfully tested for well-characterized samples under laboratory conditions. Evaluation of the CT-based analyzer under simulated on-line conditions is also presented to verify the on-line capabilities of the newly developed X-ray CT analyzer for the control of coarse coal cleaning circuits. The investigation shows that the data obtained from CT washability analyses compare favorably with experimental sink float data. Further, image frequency was considered to evaluate the CT-Based coal washability analyzer for simulated on-line conditions. Specifically, the number of observations (image spacing) needed for accurate sampling and the total time required to perform the calculations for a representative data set were determined. Key words: Coal washability, Computer simulation, X-ray CT analysis

Jan 1, 2003