Search Documents

By P. Arell, D. Folkes

This paper presents the basics of EPA’s Hazard Ranking System (HRS), which is used to evaluate sites for possible inclusion on the Superfund National Priorities List (NPL). The paper describes the surface water, ground water, air, and soil exposure pathways and how they are applied to mining sites. Key factors contributing to the site score include the likelihood of a release, waste characteristics, and the targets for each pathway. Waste volumes, definitions of landfills versus surface impoundments, and background concentrations are of particular importance to mining and smelting sites. Because of the presence of metals, large waste volumes, and observable releases, mining and smelting sites often receive high enough scores to be proposed for the NPL based on a single path-way. Neverthess, owners and operators can take steps to reduce the risk of being scored, and to reduce the potential for high scores.

Jan 1, 2004

By P. R. Dugan

Sulfur removal from high sulfur coal has several objectives including: a) reduction of the atmospheric load that contributes to the problem of acid precipitation; b) reduction of ash, which contributes to decreased energy transfer in boilers, as well as ash disposal; and c) alleviation of the social and economic dislocations related to uneven geographical distribution of sulfur in coal reserves. Cost in relation to the value of refined coal will govern the development of an emerging coal refining industry. Estimation of the premium paid by power companies for coal with a low sulfur content is a good estimate of the value that will be added as the result of refining. Estimates of premiums paid in 1984 are $28.65/t ($26 per st) for reduction of total sulfur from 370 to 1% S and greater than $28.65/t ($26 per st) for removal below 170 sulfur.

Jan 1, 1988

By Vas Choudhry, Randhir Sehgal

Conventional clean coal technologies which consist of coarse coal cleaning by gravity methods and treatment of natural fines by flotation can only remove a portion of the pyritic sulfur and ash in the coal. Higher (+90%) pyritic sulfur rejection is attainable when coals are ground to ultrafine sizes to enhance liberation of the mineral matter and then cleaned. However, cleaning of coal at very fine sizes poses a number of unsolved problems, the chief one being the loss of cleaning efficiency. This, of course, means that liberation of pyrites does not always equal its rejection. In addition, the dewatering of fine- cleaned coal, and its handling, transportation, and acceptability to the utility industry a1 so pose considerable technical and economic problems, especially when compared to the FGD alternative. This paper addresses some of the critical issues involved in the cleaning of ultrafine coal s.

Jan 1, 1989

By Thomas A. Colbert

Permanent reclamation of tailing and acid forming mine wastes in the western United States has been largely a losing proposition. There have been few if any successes without actual burial of wastes with soil, overburden, waste rock or other material more amenable to reclamation. Rather than major breakthroughs, development of new techniques has been slow and steady. Revegetation of acid forming wastes with little or no soil cover is now probably feasible. Three key elements include the use of adapted plant species which are now becoming commercially available, lime and selective bactericide for controlling acid, and organic amendments such as manure or sewage sludge. Benefits of this type of reclamation often include reduced mobility of toxic metals and improvements in water quality. With a stringent regulatory regime for mine wastes impending under Strawman II, the importance of good, economical reclamation techniques will become critical to successful and profitable western mining operations.

Jan 1, 1991

By Nathaniel Arbiter

The increasing size of flotation cells as the use of flotation has increased is traced from the first United States application of the process in Montana in 1911 through the following eight decades, using data from the Taggart handbooks (1927) and (1945), from the SME Handbook (1984), and from recent manufacturers' catalogues and other sources for the 1980s and 1990s. With the earliest mechanical cells less than 1 m3 (359) in volume and the largest now available at 200 m3 (7,000ft3), three requirements are necessary: 1) demonstration of advantages in replacing smaller volume by larger volume cells; 2) estimating power requirements, impeller dimensions, and operating rpm by correlation equations; 3) considering effects of using larger cells, in necessarily much shorter rows, on process kinetics. The resulting seven tables that address these problems are presented, and their implications discussed.

Jan 1, 1999

By J. Mersch Ward

Homestake Mining Company has identified a significant native sulfur resource at its Cinnabar Canyon prospect in Mono County, California. Elemental sulfur occurs as replacements, fracture coatings and breccia fillings in a thick sequence of Miocene-Pliocene intermediate volcanic rocks. The deposit extends along a northwest trending regional fault and measures approximately 900' in width, at least 1800' in length, and has a thickness in excess of 200'. The deposit lies approximately 150' below the surface and is covered by a silicified cap of volcaniclastic strata. The deposit has been delineated by rotary and core drilling. Utilizing a grade cutoff of 5% elemental sulfur, the delineated deposit has a probablelpossible resource of 16.1 million tons of ore averaging 17.9% elemental sulfur containing 2.57 million long tons sulfur. Assay grades within the resource area range up to 40% sulfur over a 40-foot intercept.

Jan 1, 1992

By J. F. Abel, R. J. Spengler

Convergence measurement across the 17.4-m (57-ft) high shaft station/loading pocket at Mt. Taylor provided continuing verification of stability and safety. Three levels of instrumentation, consisting of three lines each, were installed and monitored. The instrumentation showed that the flexible lining restrained the adjacent rock. The flexible lining consisted of pea gravel with neat cement between rock and liner plate, wooden crush blocks between liner plate and steel ring beams. The loading pocket is elliptical, 11.6 x 9.6 m (38 x 31.5 ft) inside diameter. The crush blocks were designed to allow 15 cm (6 in.) of convergence. Maximum predicted convergence was 7.0 cm (2.75 in.), and 5.7 cm (2.25 in.) was measured. Convergence measurements also demonstrated decreasing deformation with respect to elapsed time and distance from the measurement station to the temporary bottom of the shaft excavation.

Jan 1, 1987

By Richard D. Grove

The on-stream analysis of phosphorus and silica has not been possible by XRF techniques and only recently has some success been indicated with quantitative XRD for P. Yet there has been a recognized need for an on-stream analysis of P and acid insoluble to permit the automatic control of phosphate rock flotation plants which produce some 30-40 million tons of concentrate each year in the southeastern U.S. IMC Fertilizer, Inc., the largest U.S. phosphate rock producer, embarked on a program to develop such an on-stream analysis capability several years ago. Following many months of lab and prototype development, the first commercial installations started in December 1986 and now have completed some 400,000 analyses with surprising accuracy, precision and reliability. The use of these devices in the improved control of the phosphate flotation plant is currently receiving some very serious attention at IMC.

Jan 1, 1989

By R. Haecker, S. Gupta, P. Somasundaran

Rock disintegration processes are usually inefficient and costly operations in mineral beneficiation, mine development and oil well preparations. Thus, there is a strong need for improving the energy efficiency of unit operations such as drilling and comminution. The effects of selected cations and anions on drilling efficiency in a hard rock formation (Dakota Sandstone) were studied. The zeta potentials and the tensile strengths of the drilled samples were measured under similar chemical conditions. The chemicals tested included MgCl2, Na2CO3, AlCl3, NaCl and Dodecylammonium chloride. The results indicated that drilling rates can be enhanced or retarded depending on chemical conditions such as the solution pH and the type and concentration of reagents. Drilling data are correlated with mechanical (tensile strength) and interfacial (zeta potential) properties of the rock formation. The mechanisms involved are discussed in light of Rehbinder's and Westwood's theories.

Jan 1, 2000

Acid mine drainage is still a common problem in the northern Appalachian high sulfur coal region despite mining and reclamation practices applied to control it. Mining companies must treat water with alkali to raise pH and precipitate metals in order to discharge the water into receiving streams. Common chemicals used to treat drainage are limestone, hydrated lime, soda ash briquettes, caustic soda, and ammonia. Each chemical has advantages or disadvantages under specific conditions. A simple spreadsheet program was developed to evaluate costs of treating acid mine drainage across several specified water quality parameters and time horizons. Caustic soda and soda ash were shown to be cost effective for treating low flows and low acidity over short time periods. However, as quantity of water increased, quality decreased, and time horizon increased, the ammonia and hydrated lime systems were found to be much cheaper than caustic soda.

Jan 1, 1991

By H. L. Ford

Flocculant testing should be initiated for economic or performance reasons. When the decision has been made to test, the laboratory can provide valuable information concerning the various products under consideration. Properly conducted laboratory tests can determine: 1. If two flocculants are needed to achieve clarity or density. 2. Ease of mixing. 3. How quickly the material goes into solution. 4. Stability of prepared f locculant solution. 5. Stability of the floc formed. 6. Amount of mixing required for proper floe formation. 7. Optimum flocculant concentration. 8. Optimum pulp density. 9. Approximate location of the point of addition. 10. Single or multiple addition points. When a flocculant shows promise in the laboratory, a plant test should be scheduled. During the plant trial, arrange for normal conditions and start testing with a crew that is most familiar with the unit operation where the flocculant will be applied.

Jan 1, 1986

By Yelloji M. K. Rao, P. Somasundaran

Reagents of biological origin are becoming more and more important in the field of metallurgy, especially in the areas of mineral processing and hydrometallurgy. The advantage of lower operating cost over physical and chemical processes and the capacity to operate with low grade ores make the microbial processes further attractive. In this paper, the role of microbes directly as a reagent and microbially produced reagents or secreted metabolites in mineral processing and hydrometallurgy will be discussed. Adhesion of microbes to surfaces is known to alter the hydrophobicity of minerals. Applications include surface modification to impart hydrophobicity or hydrophilicity on sulfide or non-sulfide minerals and dissolution of precious metals. Microbes can also perform the role of flocculating agents. Biosorption of toxic and heavy metal ions by microbes are finding application in treating tailing ponds. Mechanisms associated with the use for microbially produced reagents are discussed along with some recent results.

Jan 1, 1994

By K. N. Han

The leaching behavior of palladium in ammoniacal solutions was investigated by using the rotating-disk technique in an autoclave. The study included the effects of rotation speed, temperature, oxygen pressure, composition of ammoniacal solutions and catalysts on the overall leaching rate. The dissolution of palladium in ammoniacal solutions was discussed in terms of the thermodynamics and a kinetic model. Even though the Eh-pH diagram suggests that palladium metal can dissolve in ammoniacal solutions at room temperature, it was found that the dissolution was very slow at temperatures below 100 °C but was significantly improved at higher temperatures. It was also found that the rotating speed of the palladium disk had no effect on the leaching rate. The apparent activation energy was found to he 69.7 kJ/mole. Based on the results obtained, it was concluded that the dissolution of palladium is controlled by chemical reaction.

Jan 1, 1999

By N. C. Saxena, S. K. Puri, A. K. Pal

The condition-based monitoring system is an important innovation for reducing the downtime of costly, heavy earth- moving machinery (HEMM). Vibration severity measurements were made on the HEMM located at the Gevra Project, the largest coal opencast project in India. Whenever the vibration severity levels exceeded the permissible limits, necessary actions were taken to replace the defective parts of the ma- chine. The systematic vibration monitoring of 120-t (132-st) dumpers, followed by corrective measures led to a substantial increase in component life (8.18% for an 445E Dressor and 28.44% for an MK-30 Unit Rig). The associated costs (including spareparts) were reduced by 21.55% and 25.74%, respectively. Because of the reduced downtime, savings for these two dumpers over the period from March 26 to June 25,1998, were of the order of Rs.26.47 (US$0.649) million.

Jan 1, 2000

By Kenneth Maser, Douglas W. Ounanian, Joseph S. Boyce

Foster-Miller Associates, Inc. (FMA), under contract to the Department of Transportation (DOT) and the Urban Mass Transit Administration (UMTA), is currently developing an Extruded Tunnel Lining System (ETLS). The ETLS would reduce ground support costs in machine bored tunneling by eliminating the need for temporary support, and by slip-forming the final concrete lining directly behind the Tunnel Boring Machine (TBM). The system can advance at variable rates, from 0.6 to 3.7 m (2 to 12 ft) per hr, by combining three systems: a very high early strength concrete, continuously produced and delivered by a concrete process system; a slipform/bulkhead system for supporting the concrete prior to strength gain and exposure; and a control system for form/bulkhead alignment and concrete process control. Large-scale tests are planned to demonstrate the system in a 3 m (10-ft) diameter steel "tunnel".

Jan 1, 1981

By Herbert Pöllmann

The mineralogical and chemical compositions of various waste materials undergo different reactions when treated thermally The heavy metal contents can be bound to stable phases. These minerals are called reservoir minerals. The main property of these minerals is the stability in their geochemical surrounding containing the heavy metal cations and anions. Examples for these minerals are apatites, spinels, garnets, perovskites and also water containing minerals like ettringites, metal-metal-hydroxi salts, jarosites and zeolites. When the chemical compositions of different wastes are mixed according to the compositions of the new formed minerals, a probable reuse of these wastes can be obtained. The use of waste incineration ashes for the production of cementitious binders and the use of flue gas desulfurization products for cement additives are shown. Also the transformation of highly contaminated materials into stable reservoir mineral assemblages are shown including the study of stabilization and immobilization techniques.

Jan 1, 1998

By Neville G. W. Cook, John Kemeny

Utilizing the principles of elastic-brittle fracture mechanics, stress-displacement relationships are derived for an elastic solid containing a slip plane consisting of various configurations of collinear arrays of cracks. These models take into account the heterogeneous nature of slip planes as observed in the lab and in the field, and are relevant to the behavior of rock containing faults, joints, bedding planes, and fractures. All of our models exhibit slip weakening behavior, and show regimes of both stable (aseismic) and unstable (seismic) deformation. For given configurations of cracks and applied boundary conditions, our results show explicit ly the energy released through unstable crack growth. For instance, it is found that two equal length cracks growing together release more seismic energy than, say, a large crack growing into a small crack. Also, by allowing cracks to coalesce, our models show multiple stick-slip events without crack healing or other geochemical means.

Jan 1, 1986

By J. A. Herbst, Y. C. Lo

This paper attempts to answer whether or not the mill performance at Bougainville could have, in fact, been predicted by the population balance approach, or whether other special considerations are required to explain their behavior. In recent studies, the plant tests were performed at Bougainville and batch tests were carried out at the Utah Comminution Center. In all tests power measurements were made and several levels of energy input to grinding were evaluated. Also, tracer tests were performed for mill residence time determination. The performance of Bougainville's 5.5x6.4-m mill has been very successfully predicted by population balance methods. The prediction errors are only about 1% on product size distribution and 4% on power with a mill volume scale-up of 3790:1. It is significant that this approach will reduce the risk of failure in large mill design that has been recognized in traditional methods.

Jan 1, 1987

By A. K. Sheik, W. G. Pariseau

A small underground mine in northern Idaho was used as an experimental facility for studying the role of water in the analysis of mine-opening stability. Laboratory test data, borehole measurements and geological mapping assisted in the construction of a coupled finite element model of the rock mass. The model was used to make quantitative estimates of rock stress, strain and displacement changes and to make estimates of the water pressure and flow velocity changes that occurred during historical mining. Stope cuts and wet fills were included in the analysis. The stability of the crown pillars between stopes was of particular interest. The relatively low effective stress and high rock-mass strength showed that water pressure changes were of no great consequence, which is in agreement with experience. The computational tools used in the analysis may be applied to other wet mines with appropriate changes to site-specific data.

Jan 1, 2002

By M. B. Díaz Aguado

Traditionally, the practical evaluation of a mining project for a potential investment has been made considering mainly technical aspects. But the concept of sustainable development has introduced significant changes in the factors analyzed to make the final decision. This paper proposes an empirical evaluation of a project considering not only technical, economic and financial parameters, but also associated risks and other intangible aspects, such as political considerations, stability in the legal frame, social factors and environmental issues. The proposed methodology is practical and easy to apply for project management. Among its main advantages, the following could be quoted: using this evaluation two different projects or locations of a same project can be compared, future behaviors could be predicted, the index incorporates a new approach to specific mining projects and this perspective could also be applied to other projects with environmental and social impact, such as civil works or industrial projects.

Jan 1, 2007