Search Documents

By M. M. Botz

There are currently more that 460 mines worldwide that utilize cyanide for gold and silver extraction. Despite this large number of cyanide-related mining operations, there have been no published accounts during the previous 25 years of the death of humans due to cyanide as a direct consequence of major mining-related environmental incidents. All published accounts of human deaths due to mining-related environmental incidents have been the result of physical inundation with tailings or waste rock materials. It appears that major mining-related environmental incidents have not been concentrated in any geographic location, are likely to occur regardless of the size of the mining company and do not occur more frequently with a specific type of mining activity. Several cyanide treatment and recovery technologies have been widely demonstrated to reliably control cyanide levels in mining solutions. With proper use of these technologies, tailings cyanide concentrations can be maintained at levels protective of wildlife while reducing the potential for adverse environmental incidents. The development of an international cyanide code of practice or management plan is recommended and should take into consideration the adoption of a weak-acid-dissociable (WAD) cyanide standard that maintains the levels entering a tailings impoundment below 50 mg/L.

Jan 1, 2001

By Hassell E. Hunter

The Wyoming Mineral-Conoco Crownpoint Project represents the first time that big hole drilling has been exclusively used to develop totally a privately financed mine below a depth of 1000 feet. Three shafts, one ten feet in diameter and two six feet in diameter, were successfully drilled to depths of 2243', 2188' and 2188' respectively and cased with hydrostatic designed steel casing. The largest shaft is to be used to handle muck and water from station excavation and enlargement of the other two shafts. A reverse circulation system with potassium chloride base mud was used for drilling. The mud was cleaned by settling in steel lined tanks with assistance by cyclone type separators. Deviation was monitored by gyroscopic surveying at 30 foot intervals and did not exceed 16 inches off plumb. Casing was designed to withstand hydrostatic pressures with a 1.5 safety factor to the large shaft and 1.25 safety factor for the smaller shafts. All casing welds were x-ray tested prior to lowering the casing in the hole. Cementing the annular space completed the operation. The total time to mobilize, drill and move off the three shafts was 363 days. The drilling operation was completed ahead of schedule and under budget.

Jan 1, 1983

By Brenda Myers-Bohlke, Tor L. Brekke

INTRODUCTION In recent years several cities in the Eastern United States have constructed subway systems in deeply weathered igneous and metamorphic rocks. Portions of these transit tunnels and shafts have penetrated zones of saprolite. The purpose of this paper is to define saprolite and discuss saprolite behavior in terms of construction and design of tunnels and shafts. Saprolites are products of in situ weathering of rock, with properties intermediate between those of soil and rock. A well-developed weathering profile can be divided into zones of residual soil, saprolite, transition zone materials, weathered rock, and fresh rock. Saprolites are distinguished by a high degree of weathering and by retention of parent rock textures and discontinuities. These structures persist as relict features because of iso-volumetric weathering (Cleaves, 1974) and formation of intergranular bonds that give cohesion to the saprolitic material. As saprolite continues to weather, the bonds are broken, causing the saprolite to decompose and disintegrate into a true residual soil mass without relict structure. Saprolites may form from igneous, metamorphic or sedimentary rocks, but are most easily recognized when derived from igneous and metamorphic rocks because of their inherent structures. The physical characteristics and properties of residual material vary as a function of mineralogic composition, structure, and discontinuities of its parent rock.

Jan 1, 1985

By P. van der Veen

The objective of this paper is to analyze the evolution of the strategic drivers of the mining sec-tor over the last half century, which has been guided by a varying and expanding list of motivations. While companies cannot survive for long unless they are making profits, the strategic drivers of the industry have gone far beyond profits since at least the mid-1970s when environmental concerns began to be taken seriously. For the most part, these forces have followed global trends and public opinion, but they have been shaped and magnified by the significant, often dominant role that the mining sector plays in many economies. While the mining sector used to be primarily motivated by the first pillar of sustainable development -i.e. the economics pillar-, in the 1970s the second environmental pillar became an important factor in decision making, and in the 1990s the third social pillar emerged as a major driver.1 The entrance of new strategic drivers has also had considerable impact on technological and organizational developments in the mining industry; however, technological changes, driven by cost reduction considerations, have in turn impacted the strategic drivers of the industry, resulting in the need for further technological and organizational developments.

Jan 1, 2007

By P. Christmann

"In June or July 2005, the European Commission will present its Thematic Strategy on the Sustainable Use of Natural Resources proposal to the Council and European Parliament, one of the seven Thematic Strategies to be developed and implemented under the 6th European Environment Action Programme in support of the European Union’s Sustainable Development Strategy defined by the European Union’s Head of State at the Göteborg European Council, in June 2001. The time scale for this Thematic Strategy is 25 years (2005-2030). This paper discusses some of the key issues related to the EU minerals and metals industry that needs to be addressed by the Strategy. These are: - the need for access to mineral reserves in the EU and abroad; - the need to strenghten the capacity of developing countries to sustainably promote and regulate the use of their mineral potential; - the need for an EU mineral resources intelligence capacity. There are additional important needs, which are not discussed in this paper, such as: - the need to foster further innovation in mining, ore beneficiation and metallurgical technologies; - the need to integrate and simplify the exisitng complex regulatory framework applicable to the EU mining industry and to effectively implement existing legislation."

Jan 1, 2005

The speed and internal accuracy of today's electronic calculators can be utilized to write an efficient slurry calculation program. The calculator's input/output printing feature offers additional benefits for data organizing and record keeping. This program allows slurry calculations to be performed without the urgency of immediately transferring a calculated result onto a process flowsheet or specification sheet. The number of flowsheets required for some hvdrometallurgical processes means the number of process stream blocks or ladder diagram entries can become substantial. Slurry calculations for such projects tend to become repetitious and tedious, and the chances for errors increase both in calculation and data entry onto process documents. Using this program has minimized both types of errors. Checking process flowsheets is particularly expedient with the program because you may "walk" through the flowsheet on a weight basis, i.e., solids rate and solids density, and have the program verify and/or correct the volume entries, gallons, and specific gravities. The program was initially used on a beneficiation project to check some 500 data entry values on ladder diagrams covering seven process flowsheets. Numerous hand calculation errors were determined and corrected, and the time for completely checking and correcting the flowsheet ladder diagrams was substantially reduced.

Jan 4, 1981

By Guillermo Krstulovich

Pillar strength is a fundamental variable in the design of room and pillar mining. A number of researchers have investigated the strength of mine pillars by loading cubical, cylindrical and rectangular model pillars to failure in a compression testing machine (1). Several of these researchers have observed an increase in the compressive strength of model pillar with an increase in friction at the platen-specimen interface (2, 3, 4, 5). It has been postulated that the friction prevents lateral expansion of the specimen, thereby exerting a confining pressure at the interface. Seldenrath and Gramberg in their work with cylindrical specimens of limestone and marble noted that the effect of clamping the ends of the specimens, i.e., to restrict lateral movement of the specimen face, was to increase the compressive strength about 10% for marble and from 50-75% for the limestone, as compared to the same type of specimens when tested with the end planes free (6). No attempt was made to determine the confining pressure exerted by the clamps. In recent years, Bureau of Mines has conducted an extensive study, similar to Seldenrath and Gramberg's, with dog bone specimens. The confining pressure exerted by the clamps was determined and an increase in the compressive strength with increasing confining pressure noted (7, 8).

Jan 1, 1970

By Somia Gurunathan, Harry Castrantas

Hydrogen peroxide and calcium peroxide are used to improve the extraction of gold/silver and reduce cyanide consumption in heap leaching and mill leaching operations. FMC's standard grade H2O2 and FMC's Permeox™ solid peroxygen, a formulated product containing cao2, was used for the experimental work. It was found that the rates of release and the longevity of these peroxygens in ore-cyanide mixtures are significantly different. When choosing a peroxygen, one of the key factors is extrac­tion time, with the longer extraction times of heap leaching primarily favoring calcium peroxide and the shorter extraction times of mill leaching primarily favoring hydrogen peroxide. A series of laboratory leach tests showed the choice between H2O2 and CaO2 to be ore and process specific. H2O2 and/or Permeox™ improved the gold extraction in four out of five ores tested. (2 sulfide and 2 oxide). Mixtures of H2o2 and Permeox™ were also found to significantly increase the gold extraction rate. A fifth ore (sulfide) did not respond to peroxygen treatment. In addition, savings in NaCN consumption was obtained with Permeox™. Both peroxygens offer economic incentives to gold processing.

Jan 1, 1992

By J. Gawler

In June 2005 the Minerals Council of Australia signed a Memorandum of Understanding (MoU) with the Australian Government which states an intention ?for mining companies and government to work together with Indigenous people to build sustainable, prosperous communities in which individuals can create and take up social, employment and business opportunities in mining regions?. Implementation of the MoU has begun with demonstration sites established across Australia. All sites are using a Regional Partnership Agreement (RPA) model as a framework for enabling local people to find local solutions to local issues in partnership with mining companies, governments and Indigenous communities. Mining and resources companies can provide important input into regional economic development and capacity building by working through local partnerships. Company benefits include gaining a social licence to operate, access to a reliable skilled workforce, better longterm relationships with Indigenous communities and sustainable regional communities. All levels of government, Australian, State and Local, are working collaboratively to address unemployment and other issues in remote Indigenous communities. The Australian Government has adopted RPAs as one mechanism for implementing its whole-of-government approach to Indigenous affairs. This leading edge work is unique to Australia and the model has applications and significant learning for other countries and industries.

Jan 1, 2007

By Terry Mattioli, Buck Bradshaw, Terry Fagg, Larry G. Nisle

Deposition of calcium carbonate scale on activated carbon in the Pinson Mining mill carbon column circuit was causing erratic gold recovery rate, long acid wash time, high carbon attrition and long strip times. Continuous addition of a blended antiscalant into the mill thickener overflow at 8 ppm reduced the average carbon acid wash weight loss from approximately 10% to < 2%. Cleaner carbon improved the gold loading rate in the mill column. The loading on Column I was increased to 175-225 oz/ton carbon from 125-150 oz/ton for a two-day carbon advance cycle. The higher loading capability has given Pinson more flexibility and better control of gold flow through their carbon adsorption, stripping and electrowin­ning processes. Preventing calcium carbonate build-up on activated carbon with this antiscalant reduced acid wash batch time. This enabled Pinson to acid wash and regenerate every batch of stripped carbon for all the adsorption circuits. Shorter strip times have also resulted from the lowering of the calcium carbonate scale level in the loaded carbon. Carbon consumption has been reduced and is now averaging 0.046 lb/ton ore for the first six months of 1990 compared to 0.072 and 0.083 lb/ton respectively in 1989 and 1988.

Jan 1, 1990

By A. Giblett, J. Shuttleworth, R. Dunne

In a previous paper (Dunne, Martins, Goulsbra, Chittenden 1997), the new gravity circuits at Telfer Gold Mine, which incor­porate Knelson centrifugal separators in both the sulphide and oxides, are described. The advantages of the new circuits over the replaced spiral ( oxide circuit) and jig (sulphide circuit) were discussed, as were the improvements in gravity gold recovety. It is of note that the installation of the centrifugal separators in themselves did not result in increased gold recovery. The realisa­tion that changes in gold room practices are required to take advan­tage of the increased fine gold recovery from the Knelson concen­trator was an important step towards improved gravity gold recov­ery. This was achieved by increasing the time taken to treat the Knelson concentrate on the shaking table in the gold room. Although this increased gold recove1y, it was found that the table tailings, especially from the sulphide circuit, still contained high values of gold. In an effort to ascertain ways in which gravity gold recovery could be fu1iher improved, a sample of the sulphide table tailings was sent to the Oretest Laboratory in Perth for testwork. The results from this program are discussed in this paper.

Jan 1, 1998

By Jeffrey M. Christian

Gold prices are rising, in what is coming to be seen as the beginning of a longer term upward trend. After languishing between $325/oz and $364/ oz from early 1991 into early 1993, prices began rising in the first half of 1993. Gold rose from a low of $326/oz in March 1993 to $414/oz on an intraday basis in early August. There was a speculative sell-off at that point, which took gold prices quickly back down to $350/oz briefly in October 1993. At that time, there still was a fair degree of skepticism about gold&apos;s price prospects. Many banks believed that gold prices could not mount a sustained rally. As prices dropped in August and September of last year, these suspicions seemed to be confirmed. Gold prices quickly rebounded, however, reaching $395/oz by early January 1994. The strength of this renewed increase led many banks, investors and others that had held negative views of gold to grow more positive. They began buying gold and trading it from the long side of the market. The result was that gold prices remained strong during the first quarter of 1994, trading between $375/oz and $390/oz.

Jan 1, 1994

By William A. Kneller

A considerable range of composition exists in rocks that have been described as chert, jasper, or flint. Their composition may be opaline, chalcedonic, quartzose, or mixed. Certain cherts, when incorporated in concrete, are known to possess nondesirable thermal and chemical properties. The inability of chert to withstand thermal shock above the freezing temperature of water is an example of such a property. Cryothermal reactions may cause disintegration of concrete, due to repeated cycles of freeze and thaw. Thermal properties are significant because small temperature changes may cause inordinate expansion and resultant fissuring of concrete. Freezing of entrained water in chert may cause excessive physical failure in concrete. Some cherts react chemically with alkalies liberated during the hydration of the cement, with resultant cracking and deterioration. Sources of concrete aggregate in Ohio have been viewed with suspicion because they contain considerable chert derived from Middle Devonian and Pennsylvanian carbonate rocks. Light-colored porous cherts from the Middle-Devonian Colum- bus Limestone exhibit the least freeze-thaw durability of the samples studied. Denser cherts may also yield to freeze-thaw stresses, but tend to be more susceptible to thermal shock. Cherts rich in opaline and chalcedonic silica usually exhibit alkali-aggregate reactivity.

Jan 1, 1966

By J. K. Neathery, T. X. Li, H. Ban, J. M. Stencel, X. K. Jiang

Upgrading molybdenite ore can be technically difficult and expensive if talc is a major impurity in the ore. The layered structure of molybdenite and talc decreases the surface specificity of floatation and suppression agents, thereby making molybdenite ore beneficiation inefficient if under some wet processing methods. However, oxidic talc surfaces may be distinct from the sulfidic or oxysulfidic molybdenite surfaces, such distinction related to electron work functions and/or densities of electron donors/acceptors sites. If such differences are present, the upgrading of finely sized molybdenite ore by dry triboelectrostatic methods may hold advantages over traditional wet methods. We report on the upgrading of molybdenite ore using a laboratory-scale, drytriboelectrostatic beneficiation system. This system employs pneumatic transport conditions to tribocharge, beneficiate and collect the fine molybdenite ore particles. Using this system, two Mo ores were beneficiated under dry conditions without the addition of water or surface modifiers and additives. Beneficiation performance was dependent on the particle size of the feed ore. The surface and particulate morphology and elemental concentrations in the parent feeds and the beneficiated products were examined by scanning electron microscopy (SEM) and optical microscopy. These data, in conjunction with a complete recovery analysis, define some potential advantages of dry, triboelectrostatic beneficiation processing and provide insight into factors controlling molybdenite ore upgrading.

Jan 1, 1999

By Charles Rubin

Mining is a capital- and labor-intensive business, and profitability often depends on the ability to squeeze maximum efficiency out of every piece of equipment to achieve safe production. This means keeping every mechanized drill, loader, truck and bulldozer operating at all times, and having a system to coordinate the movements of people and personnel. Mines often use wireless radios to connect equipment with management systems. But growth and changes in a mine?s profile over time can require upgrades to the wireless network. In its openpit gold mine near Carlin, NV, Newmont Mining Corp. has recently upgraded to microwave radio systems to increase bandwidth while maintaining round-the-clock uptime on its wireless network. For many of its operations around the world, Newmont uses Minestar, an operational control software system that allows administrators to dispatch equipment operators and use GPS to track the precise position of every piece of equipment in an operation. Each of the approximately 150 pieces of equipment at the mine has a radio on board. These radios connect to a network backbone that carries information between the equipment and the mine?s operations center. When traffic began to bog down on this network, Newmont upgraded to Exalt microwave backhaul systems to carry dispatch, inventory and control information throughout its operation.

Jan 4, 2010

By J. Loredo

In some rural regions of Peru, artisanal gold mining is currently an essential activity as it provides an important source of income. In the Huanca region (Ayacucho Department) gold deposits are not attractive for mining companies due to their reduced size, but they have enough interest for artisanal mining because of the ease and low cost of mining operations. Artisanal gold mining represents an important damage for the environment, because operations related to amalgamation processes using Hg result in special environmental problems besides the typical ones commonly associated to all mining activities. A preliminary sampling has been made in soils, materials from tailing ponds and surface water of the Acarí River, at the site of the Huanca village, according to networks specially designed for the particular conditions of the area. Studies accomplished revealed high mercury concentrations in soils and tailings. Chemical analyses of soils directly collected in the area of the active or abandoned ?quimbaletes? show mercury concentrations ranging from 15.3 mg?kg-1 to 44.2 mg.kg-1. Mercury concentrations in soils decrease as a function of distance from the before mentioned sources. Water quality of the Acarí River that flows through the area does not present important changes as a consequence of the mining and processing operations.

Jan 1, 2006

By G. W. Luxbacher

Acid rain legislation included in the Clean Air Act Amendments of 1990 caused a great deal of uncertainty regarding the price, source and production quantities of coal supplied to the eastern coal market. Powder River Basin and other western coals continue a rapidly accelerating migration eastward. South American coals move into the northern markets. States are proposing legislation to assist utilities in complying with the new regulations in hopes of maintaining their own coal industries. Some utilities question the long-term availability of eastern compliance coal. Major coal producers must make decisions now to assure their continuing presence in the market place. Several companies have adopted a strategy to acquire eastern compliance reserves, while others have invested in technology to compete as a low-cost producer. Legislation "Acid rain." This is a topic that was debated within the scientific, environmental and industrial communities for years. Those discussions resulted in a large outlay for the federal National Acid Precipitation Assessment Project (NAPAP), which was then ignored. Acid rain then became the subject of a "60 Minutes" broadcast that debunked the acid rain theory, supporting the NAPAP study conclusions. In the final outcome, however, acid rain was the driver for the Clean Air Act Amendments of 1990.

Jan 1, 1992

By Lynn I. Kelley

Industrial-mineral production contributes on the order of CDN$1.5 billion per year to the economy of Saskatchewan, Canada. Potash is the primary industrial mineral produced in the province, followed by aggregate, sodium sulphate, salt, potassium sulphate, peat, clays, silica sand, calcium-chloride brine, and "clinker." Potentially economic deposits of kaolin, diamond, and building stone are under evaluation. All of the major deposits of commodities discussed here are located south of lat 56°30&apos;N. Most of the locations are presented on Figure 1 POTASH Saskatchewan supplies approximately 30% of the world&apos;s demand for potash. Eight conventional underground mines and two solution mines produced an all-time high of more than 13 million metric tonnes of potash (KC1) (8 million tonnes K2O equivalent) in 1997, valued at over CDN$1.4 billion. All of the mines exploit the middle Devonian Prairie Evaporite. The four potash-bearing members of the Prairie Evaporite underlie much of southern Saskatchewan and extend southward into North Dakota and Montana and east- ward into Manitoba (Fig. 2). Halite and anhydrite separate the potassic members. The evaporite beds locally are interrupted by solution structures (anomalous ground). Some of the structures may be related to deep-seated tectonic features.

Jan 1, 1999

By D. M. Wyslouzil

Conditioning, in the conventional sense, means providing sufficient agitation and contact time for the reagents to react with the minerals in the ground ore. High intensity conditioning (HIC) on the other hand, as described in this paper, recognizes the need to exceed this minimum power input over a suitable length of time to induce aggregation of the finest size fraction. Time alone is not sufficient to achieve aggregation. The threshold minimum power input, kW/m3, depends on many surface properties of the fine particles and can vary considerably. In addition, the mechanical aspects and the chemical conditions must be matched to achieve good aggregation. Treatment of complex sulphide ores, requiring fine grinding for liberation, offers a large field for the application of HIC. Improved flotation rates and enhanced selectivity are some of the benefits that can be expected. This unit operation has now reached the level of commercial application. Lakefield Research considered HIC not from a fundamental point of view but as a means of solving difficult mineral processing situations arising in actual operating plants. This paper summarizes the effects of the various chemical reagent combinations that had been applied to promote faster, more selective flotation, higher mineral recoveries and cleaner separations, using HIC.

Jan 1, 1995

By Brent K. Nelson, D. Lee Petersen, Charles R. Nelson

INTRODUCTION The Soudan 2 Cavern was completed in 1986 as a physics research laboratory located 713 m below ground in northern Minnesota. A paper in the 1985 RETC proceedings presented the background and planned usage for the cavern, site investigation and rock conditions, contract documents, and a bid summary. This is a follow-up paper describing construction of the cavern. The Soudan 2 excavation, 71.8 m long by 13.9 m wide by 11.6 m high, was excavated by drill and blast methods and mucked by crawler tractor and mine hoist. The excavation sequence consisted of twin top-heading pilot tunnels followed by removal of the top heading pillar and finally the bench. Various blasting designs were used to achieve adequate breakage and acceptable levels of blast damage control at the cavern perimeter. The geologic conditions exposed in the cavern, and the support needs of the rock encountered, are compared to the conditions interpreted from the site investigation. The influence of specific geologic features on cavern performance will be described. Initial support and final lining consisted of full length grouted rockbolts and reinforced and plain shotcrete. Trials were conducted with steel-fiber reinforced shotcrete and microsilica additives. The performance of the rock and support systems was tracked with single point extensometers, convergence measurements

Jan 1, 1987