Search Documents

By Jamai Rostami

Mining, perhaps more than other industries, has been under pressure to achieve higher productivity, while reducing costs and environmental impacts. This has encouraged a move toward large-scale operations and greater integration and automation of systems. Mechanization is being used increasingly to raise production and reduce labor requirements. Yet, while transportation, ventilation and other activities have benefited from this trend, mechanization of rock excavation (for development and production) has lagged. The switch to a mechanized excavation system can be complex, requiring a thorough study of operational and cost benefits to be successful. To justify the high capital cost of mechanical mining equipment, production rates and the true costs of machine mining must be accurately estimated. To evaluate the cost effectiveness of mechanical mining for a particular operation, the total production cost (capital and operating) must first be estimated. This requires a reliable estimate of the production rate of the candidate mechanical excavator. Previously, the variable nature of rock caused performance prediction of these machines to be more an art than a science. Additionally, some of these machines are highly sensitive to operator skill. They all depend on their backup systems. The effects of interaction with the overall mining operation can be difficult to forecast. And a new system must surmount psychological barriers before it can become truly operational.

Jan 1, 1994

By E. H. Cho, P. K. Dai

An acid mine drainage sludge sample, containing 3.6% Mn, 0.18% Ni, 0.15% Co and 0.39% Zn, was obtained from central West Virginia. The sample was leached at room temperature with a pH 3 sulfuric acid solution. Air was then bubbled through the leach solution at pH 4.5 to precipitate the iron. The leach solution contained 258 ppm Zn, 105 ppm Ni, 90 ppm Co and 2050 ppm Mn. Three solvent extraction studies were performed to selectively extract these metal ions in a sequential operation with DEHPA. Cyanex 272 and Lix 84. The A/O ratio was one, and the extractants were diluted ten times with kerosene. A study of solvent extraction with DEHPA showed that Zn could be extracted without Ni or Co up to a pH of 2.75. A pH of 2.75 is considered to be the optimum pH to maximize the selective separation of Zn from Mn. The separation factor of Co over manganese suggests that the two metal ions should be extracted together by Cyanex 272. The separation factor of Co over Ni indicates that these two metal ions can be separated most effectively around pH 5.3. Also, Ni can be effectively extracted by Lix 84 above pH 5.5.

Jan 1, 1995

By Frank E. Dalton, Bart T. Lynam, Forrest C. Neil

The Tunnel and Reservoir Plan (TARP) is the largest tunneling program in the history of the metropolitan Chicago area (Figure 1). Between September 1976 and September 1977, rock tunnel contracts having an estimated cost of approximately $420 million will be advertised. During the past six months, the Metropolitan Sanitary District of Greater Chicago (MSDGC) has awarded contracts for 16.5 miles of rock tunnels in diam of from 9 ft to 30 ft having a total bid price of $120,261,750. RECENT CONTRACT AWARDS Addison-Wilmette Tunnel $63,140,480 Upper Des Plaines #20 Tunnel 35,749,664 Upper Des Plaines #21 Tunnel 21,371,607 Addison-Wilmette Tunnel The first contract was advertised in September 1975. This contract, described as the Addison-Wilmette Tunnel, runs from Wilmette Harbor at Lake Michigan under the North Shore Channel to Addison Street in the City of Chicago, a distance of 10 miles. The contract calls for constructing approximately 27,750 linear ft of 30 ft ID and 24,020 linear ft of 22 ft ID unlined rock tunnels, excavation of two construction shafts, and the excavation of 32 drop shafts of various diam. Two hundred ninety-three companies were notified of this contract being advertised, 70 companies took out contract specifications and 3 companies ultimately submitted bids. The contract was awarded to a joint venture of:

Jan 1, 1976

By Pierre M. Matheron

TRANSMANCHE-LINK is responsible for designing, developing and implementing the project for a fixed link under the English Channel, comprising two running tunnels of diameter 7.6 metres and a service tunnel of diameter 4.8 metres. The three tunnels will all be 50 km long, with 37 km bored through chalk marl at a depth of 40 metres under the sea bed. The tunnels will be driven from both sides of the channel from intermediate addits above the coastline on either side with a 55 m access shaft at Sangatte in France and two "descenderies" or inclined tunnels addits and a shaft at Shakespeare Cliff on the English side. A total of eleven tunnel boring machines will drive the 150 km of tunnels. The major part of the tunnel linings will be built of precast reinforced concrete segments, and two plants have been specially built to produce the necessary 725,000 segments. Seven million cubic metres will be evacuated on wagons along the tunnels and then lifted by belt conveyor on the English side, and by hydraulic mucking from the bottom on the French side. Preliminary work started early in 1987 with manufacture of the first boring machines, construction of five precasting plants, boring of the Sangatte shaft in preparation of the Shakespeare Cliff entrances. The principal project dates are :

Jan 1, 1987

By Robert B. Gordon

The Reverse Curve Tunnel Project was located in Glenwood Canyon, Colorado approximately twelve (12) miles east of Glenwood Springs. The Project was one of many being constructed over a period of time by the State of Colorado, Department of Highways to improve Interstate 70 to four lanes as it travels thru the environmentally sensitive Glenwood Canyon. The Project consisted of excavating and concreting a tunnel approximately five hundred fifty (550) feet long, forty two (42) feet wide, and thirty two (32) feet high. The designer was Parsons, Brinkerhoff, Quade and Douglas, with geotechnical consultation provided by Woodward Clyde. CONSTRUCTION CHALLENGES There were several significant construction challenges presented primarily by the physical location of the Project. In this study each problem will be discussed, as well as how it was overcome by construction methods and/or design requirements. Portal Excavation - One of the most difficult areas of work on the Project consisted of excavation and stabilizing the East and West Portal rock prior to tunnel excavation. The Reverse Curve Tunnel passes through a sheer walled cliff face which is approximately two hundred fifty (250) feet high. Geologically the cliff consists of primarily sedimentary deposits with open, weathered joints and vertical faulting. Before the tunnel excavation could begin, a narrow sliver cut had to be excavated and rock

Jan 1, 1989

By Robert A. Jankowski, Jonathan Kelly, Edward F. Divers

Results for the first underground test of the ventilated drum in a U.S. coal mine are presented. Tests were conducted by the Bureau of Mines through a contract research program with Foster-Miller, Inc., to evaluate dust control effectiveness in a western mine and for gas control in a full scale laboratory facility. The ventilated drum is designed to reduce the amount of dust from cutting by drawing dust-laden air from the cutting zone through twelve water- powered "dust capture" tubes built into the shell of the shearer drum. High pressure water up to 1 12.48 kg per cm2 (1,600 psig), released from sprays, induces maximum airflow of 1.89 m3/sec (4,000 cfm) from the face side of the drum and provides cleaning for respirable dust and improved methane dispersion. At the gob side of the drum a deflector plate, attached to the cowl arm, turns the water spray and a proportion of the cleaned air back into the cutting zone. More than 50 ventilated drums have been installed to date in England, and their tests carried out on fixed height and single-ended ranging drum shearers have shown reductions in respirable dust of 60-80 pct, as compared with conventional wet cutting. The U.S. test on a double drum shearer showed slightly lower reduction.

Jan 1, 1987

By Yutaka Mochida

OUTLINE Beginning in 1946, a careful geological survey was made of the Tsugaru Straits. In 1964, excavation of the exploratory tunnels were started to observe the characteristics of faults and rock formation directly, and to study construction methods of excavation and sealing water inflow. In March 1971, the investigation stages were over, and in April 1971, the construction project was authorized from the government. The geological features in the straits may be divided into three broad classes. One third consists of andesite on Honshu side. The other two thirds consists of tuff. The middle of the straits consists of tuff, so-called Kuromatsunai-layers. On Hokkaido side, it consists of tuff, called as Kunnui-layers. There are nine noteworthy faults on the route. Prior to the excavation of the main tunnel, the horizontal pilot tunnels and service tunnels are made. Exploratory borings are taken to confirm the geological conditions and the presence of gushing water. Groutings for sealing water inflow are carried out when necessary. In geologically bad conditioned sections such as disintegrated or fractured zones, special methods are applied. In geologically good zones, the tunnels are bored through using the same methods as for a mountain tunnel driving. The pilot tunnel being constructed at the sea bottom is under direct control of the Japan Railway Construction Public Corporation. The service tunnel and the main tunnel are being excavated by contractors.

Jan 1, 1981

By Jon Y. Kaneshiro, Gregory E. Korbin, Stephen J. Navin, Larry J. Stout

Sewage presently being discharged into the Tijuana River Valley pollutes the valley as well as the beaches in the South Bay of San Diego, making the beaches unusable nearly year round. The SBTO will convey flows down a 8.5 m (28 ft.) by 58 m (190 ft.) deep drop shaft, through a 3.35 m (11 ft.) by 5.8 km (3.6 mile) long tunnel, and up a 46 m by 2.7 m (150 ft. by 9 ft.) riser shaft connecting to a 1.5 km (0.95 mile) of seafloor pipeline and 1.2 km (0.76 mile) of diffusers on the ocean floor. The drop shaft will be sunk through 38 m (125 ft.) of saturated sands and gravels and 20 m (65 ft.) into the dense fine sands of the San Diego Formation. The tunnel liner has been designed as a five piece, single pass, gasketed, bolted, reinforced concrete liner designed to withstand an external head of 76 m (250 ft.) of water and internal operating head of up to 27 m (89 ft.) and to accommodate movement at the numerous fault crossings. The tunnel is contemplated to be driven with a state-of-the-art Earth Pressure Balance Machine (EPBM) or slurry shield machine through a wide range of conditions from clay to gravel with boulders.

Jan 1, 1995

By Y. S. Kim, A. Bailey

A feasibility seismic refraction and reflection field survey was conducted at the U. S. Borax Company open-pit mine, Boron, California by the writers during the weekend of March 13 and 14, 1976. This field survey was carried out as a preliminary investigation primarily for the purpose of evaluating and establishing the ability of such geophysical techniques to locate and outline the subsurface openings of the old room-and-pillar mining under the present open-pit. The value of such knowledge about the old underground workings is directly related to the safe and economical operation of the open-pit mine for the company. Although mine maps of the old underground workings are available at the mine, the extent of roof and wall cavings and the present condition of the old underground openings are unknown. Owen and Suhler (2) are the first investigators who used electromagnetic methods, Pulse-Echo System, and electric resistivity measurement to solve the problem without success. A few years later, Herzig and Owen (1) attempted to solve the problem with application of earth resistivity measurement method with unfavorable results. The U. S. Borax Company carried out an extensive study for slope failure problems of the open-pit with application of dipmeter measurements. However, the slope stability study was not correlated to the old underground openings lying under the present open-pit (3).

Jan 1, 1977

In conjunction with steady increases in production levels, long-wall operators have applied greater quantities of ventilating air to control respirable dust and methane gas. As a result, air velocities greater than 7.6 m/s (1500 fpm) have been measured on longwall faces. Operators have expressed concern over the potential entrainment of respirable dust at these high-velocities, especially during shield advance as dust falls from the shield canopy directly into theair stream. Laboratory tests to simulate dust liberation by shield movement were conducted at the Pittsburgh Research Laboratory of NIOSH in a wind tunnel designed to study dust entrainment in high-velocity airstreams. Dust was introduced into the tunnel to determine dust concentration as it relates to entrainment, dilution, air velocity, and particle adhesion. Airborne dust samples were obtained by iso-kinetic sampling using BGI cyclones to quantify respirable dust concentration at the various air velocities. Laboratory tests were con-ducted at velocities ranging from 2.0 to 10.1 m/s (400 to 2000 fpm),and significant differences in airborne respirable dust levels were measured. This research is being conducted to provide fundamental information on the entrainment characteristics of respirable dust at high air velocities, which will subsequently lead to solutions for shield dust control. A discussion of the test procedures and results are presented.

Jan 1, 2004

By R. W. Seedsman

Mandalong Mine was originally planned to operate with panel widths of 250 m and a predicted surface subsidence in excess of 3 m. The consent conditions applied by the NSW government on this mine plan were very tight and, following a change in ownership, were considered by the new operator to present a number of unacceptable business risks An acceptable risk profile for the mine layout restricted surface deformations to less than 500 mm vertical subsidence, less than 7 mm/m tilt, and less than 5 mm/m strain. Empirical subsidence prediction methods indicated that it would be necessary to reduce extraction panel widths of 80 m - an uneconomic option. The application of a number of rock mechanics concepts identified that the local overburden geology could be exploited such that panel widths of up to 175 m could be possible. The 125 m width was selected as a low-risk introduction of this new subsidence prediction method. The extraction of the first 2 longwall panels has demonstrated the validity of the prediction subsidence method and has provided the opportunity to refine the selection of key input parameters. The impact of mining through a zone of thrust faults was successfully predicted. The mine is now planning the introduction of 160 m wide panels, and will review the associated subsidence impacts prior to any further increases in width.

Jan 1, 2006

By Vincent Castronova, Jane Y. C. Ma, Joseph K. H. Ma, Chang-geng Mo, Carl J. Malanga

A group of bisbenzylisoquinoline (BBIQ) alkaloids has been shown to exhibit various degrees of effectiveness in preventing silicainduced fibrosis in animal models (1, 2). The capability of these drugs to interact with phosphatidycholine vesicles and rat alveolar macrophages was studied using fluorometric and equilibrium dialysis methods. The lipid binding affinity of these alkaloids was found to depend upon several structural factors including hydrophobic substitutions, the chiral configurations, and the double oxygen bridge-restricted conformation of the benzylisoquinoline moieties. Tetrandrine, which is highly effective in preventing fibrosis, showed strong binding to both lipid vesicles and alveolar macrophages. In contrast, curine and tubocurine, which have little or no effect on silicosis, exhibited only weak binding to lipid vesicles and almost no binding to cells. The moderate binding affinity of fangchinoline to vesicles and cells corresponded to a moderate effectiveness of the compound as an antifibrogenic agent. Methoxyadiantifoline, an alkaloid of unknown antifibrogenic potential, also exhibited high binding affinities for lipid and cells. In summary, this study indicates that alveolar macrophages exhibit large binding capacities for certain members of the BBIQ alkaloids. A positive correlation was observed between binding affinity to alveolar macrophages and the reported antifibrotic potency of these compounds, suggesting that the ability of these drugs to interact with alveolar macrophages may be a key step in inhibition of the progression of silica-induced pulmonary disease.

Jan 1, 1991

By Louis M. Schlesinger, Joel F. Hutwelker

A pilot plant was constructed to attrition scrub and deslime North Carolina phosphate ore. A 15.2 cm (6 in.) diameter pilot-scale Linatex Hydrosizer was used for desliming. Four tests were run at a throughput of 2.9 t/hr/m2 (0.30 ton/hr/f t2) and a teeter bed density of 1.12-1.13 g/cm3. The teeter water flow rate was varied to create an upflow velocity ranging from 0.25-0.47 cm/s. (This latter value is equal to the terminal settling velocity of a 200 mesh (74 micron) particle having a density of 2.7 g/cm3.) The recovery of +200 mesh oversize to the sizer underflow was 95%-96%, regardless of the teeter flow rate. The recovery of -200 mesh undersize to the sizer overflow increased from about 90% at 0.25 cm/sec to 100% at 0.47 cm/sec. A metallurgical balance that was conducted for one of the tests showed that less than 2% of the phosphatic value was lost to the overflow. A fifth test was run using an upflow velocity of 0.47 cm/sec; however, the teeter bed density was maintained at 1.05 cm/sec. This change had the effect of reducing the cut point (d50), while maintaining complete slime removal.

Jan 1, 1993

By Osvaldo Bascur, Laurent Garrigues, Nouna Kettaneh, Svante Wold

The chemical, oil, semiconductor, mining, and paper and pulp industries, as well as most other modern industries, are rapidly expanding the range of measurements used to characterize raw materials, process steps, intermediates, and final products. In addition, process variables such as temperature, pressure, and flow become more and more numerous, providing extra information on the state of the process. However, no matter how many sensors are added, the underlying sources of variations that drive the process behavior remain constant. On the other hand, the measuring frequency of these data has increased from once a day or once an hour to once, ten, or even hundred times a minute. This gives masses of data that are swelling in both directions (more variables and more observations). These data need to be properly stored, managed, and analyzed to provide diagnostics about the state of the process as well as an understanding of the relationships between different parts of the process and the product properties. Projection methods such as PCA (principal components analysis) and PLS (projection to latent structures) compress process data to informative summaries of the original variables. These can be shown on line, providing an efficient, graphically oriented suite of diagnostics regarding the "health" and performance of the process. The power of these methods is illustrated by two examples of industrial data in the mining industry.

Jan 1, 2000

By John E. Urosek, Jack E. Tisdale

The Mine Safety and Health Administration (MSHA) has developed a Mine Ventilation Bleeder and Gob Training Course. This three day course is designed to increase the knowledge and understanding of bleeder ventilation systems. It discusses concepts, designs, plan approval, inspection and evaluation of bleeder systems. This paper will introduce some of the material contained in that course, focusing on the inspection, examination, and evaluation of bleeder systems. The regulations addressing the use of bleeder systems are found in Title 30 Code of Federal Regulations (30 CFR) Section 75.334. The examination requirements are found in 30 CFR Section 75.364. Section 75.364 de- scribes specific locations where examinations are to be made and specific information to be gathered at those locations. The required locations and information will be discussed in some detail with examples and illustrations. These weekly examinations for bleeder systems are designed to monitor the parameters of the bleeder system and to evaluate its effectiveness. Over time, conditions can develop in the bleeder system that affect the ventilation and lead to hazards such as methane accumulations. The hazards of methane accumulations need to be understood as such accumulations can contribute to mine explosions. The importance of additional information gathered by the mine examiner that can assist in evaluating the performance of the system will also be discussed.

Jan 1, 1997

By Balesh W. Konda, Andrew B. Cecala

Face ignitions occurring during longwall mining are increasing each year and are expected to continue to increase as deeper and gassier seams are mined. Effective methane monitoring strategies are needed to supplement techniques developed either to control the ignition sources or to dilute the gas to an acceptable concentration. Present monitoring strategies do not always detect dangerous concentrations as rapidly as they should. In a number of instances, dangerous concentrations have been observed at the shearer, but are diluted to acceptable levels when measured at the tailgate monitoring location. To effectively monitor and control methane concentrations, methane liberation and emission patterns must be identified. This need has led to a joint research effort between the Canada Centre for Mineral and Energy Technology and the United States Bureau of Mines. By combining the knowledge and experience of both organizations, the methane hazard facing underground longwall operations can be addressed more effectively. A comprehensive plan was developed to monitor methane levels throughout the panel and for an entire longwall mining cycle. In June-July 1986, a case study was performed at the Cape Breton Development Corporation's Lingan colliery in Sydney, Nova Scotia. This initial study was performed on two advancing longwall panels. Methane concentrations and flow patterns from this study are described in this report. A similar study is planned on a retreating longwall panel.

Jan 1, 1987

By T. Eisele, T. Weldum, G. Rajala, H. Walqu, S. Kawatra

The throughput and energy efficiency of comminution circuits is reduced when ore characteristics change, causing bottlenecks in some portions of the circuit while leaving excess capacity in others. The results of analysis of three years of daily grinding circuit operating data for a full-scale plant has shown that the location of bottle-necks in the circuit will change depending on the nature of the feed ore. The circuit tends to be limited by the primary mill capacity when the ore hardness increases, and limited by the secondary mill capacity with softer ores. Two methods are considered for shifting load in the circuit to relieve bottlenecks by taking advantage of excess capacity in other parts of the circuit: 1) Addition of supplemental comminution operations, such as high-pressure grinding rolls, to process specific size fractions that are not handled efficiently by the primary mill; and 2) Use of screens to shift grinding load upstream from the secondary mills back to the primary mills. In the case of the plant examined in this study, it was found that 58% of the time there was sufficient excess capacity in the primary mills that the throughput of the circuit could have been increased by using screens to shift the grinding load from the secondary mills to the primary mills.

Jan 1, 2004

By A. English, Edward Martinez, L. A. Haas, N. W. Johnson, Harrison Copper, M. E. Tawil, C. C. Harris, G. V. Jergensen, D. Halbe, M. P. Amsden

Declining US ore grades along with skyrocketing energy, materials, labor, and regulatory costs underscored the urgency for technological innovation in the mineral processing area. Re¬liance on the scale-up and automation of unit operations was the sector's primary battle plan. Debate continues on the upper size limit of concentrating plants and whether process controls should be centralized or distributed in the mill. In the materials handling area, the economics of large-scale and mobile systems, particularly conveyors, were well documented in the literature. Comminution, the most costly and energy consuming area of the processing flowsheet, saw improvements in process controls and liner designs. The trend toward larger grinding units stalled somewhat during the year owing to some operational problems at commercial plants. Research and development of apparently less expensive physical separation processes-that also boast recovery of cleaner and more environmentally acceptable products -gained momentum during the year. Because of escalating capital cost requirements for new plant capacity, the year saw a greater interest by mill designers to re-examine existing capacity. The focus here is clearly to modify or retrofit unit operations with more efficient components as an alternative to installing more costly new equipment. The problems facing the processing sector during the 1970s can be expected to continue in the decade ahead. Technological gains from scale-up and process controls appear

Jan 5, 1980

By Harry M. Edenborn, Richard W. Hammack

Experiments were done to determine if a mushroom compost-based sulfate reduction system could be used to treat nickel-contaminated mine waters. Sulfate reduction systems were established in columns containing acid-washed mushroom compost. Simulated mine waters containing 2000 mg/L sulfate and 50 to 1000 mg/L nickel were adjusted to pH 4.5 and pumped through the columns at flow rates between 15 and 25 mL/hr. During the first nine days of operation, virtually all influent nickel was removed in the columns by sorption and ion exchange mechanisms. The nickel removal rate then dropped to 18 to 30 mg Ni/day (7.8 to 12.8 nmol/ g-substrate/day), probably due to low sulfate reduction rates. When sodium lactate was added to the inflow, a sustained and seven-fold increase in the nickel removal rate was observed. Bacterial sulfate reduction rates measured in mushroom compost-based wetlands exposed to coal mine drainage are 2 to 20 times faster than the rates observed in this study. Low sulfate reduction rates in the columns may have been due to the inhibition of microbial activity by high nickel concentrations and the removal of labile organic compounds from the mushroom compost substrate during acid-washing. Results of this study indicate that bacterial sulfate reduction can effectively treat nickel concentrations up to 500 mg/L if labile carbon is nonlimiting.

Jan 1, 1992

By Kenneth L. Rubow, Virgil A. Marple, Ye Tao

Techniques are being developed for measuring the mass concentration of respirable diesel exhaust particles found in underground coal mines. Studies have been conducted over the past five years to investigate size selective sampling techniques to measure the respirable mass concentrations of diesel exhaust and mine dust aerosol particles in underground coal mines. Results from these studies have been used to develop design and performance criteria for a personal diesel exhaust aerosol sampler. Three personal diesel exhaust aerosol samplers have subsequently been designed and evaluated in both laboratory and field settings. These samplers use size selective classifiers for the determination of the respirable mass concentrations of mineral dust and diesel exhaust particles. Their designs are based on the premise that diesel exhaust particles are predominantly less than 0.8µm while mineral dust is greater than 0.8 µm. One design, selected for field evaluation, consists of a 10 mm nylon respirable dust cyclone followed by a 0.8 µm cutpoint impactor and afterfilter. The cyclone removes the large nonrespirable particles while the inertial impactor stage, collects the mineral dust on an impaction plate and allows the diesel particles to penetrate to an afterfilter. The two sample fractions of the respirable particles (<0.8 µm and >0.8 µm) are gravimetrically analyzed to determine the concentrations of the diesel and mineral dust portions in the respirable coal mine aerosol.

Jan 1, 1991