Search Documents

By Glenn A. Shirey, Robert D. Stoessner, S. Gopalakrishnan

Under a contract awarded by the U.S. DOE-PETC, the Pennsylvania Electric Company and New York. State Electric and Gas Corporation are conducting a test program to evaluate and optimize the performance of a two-inch air-sparged. hydrocyclone (ASH) for cleaning fine coal. The test program is being conducted at the Homer City EPRI Coal Quality Development Center, utilizing Upper Freeport coal classified to minus 0.15 mm as the process feed material. A matrix of experiments has been conducted to establish the influence of significant design and operating variables (including overflow and underflow orifices, inlet slurry pressure, airflow rate, and reagent dosage) on the production of deep cleaned coal. Performance of the ASH is being compared to conventional froth flotation, utilizing advanced techniques and selected flotation reagents. This paper focuses on work completed to-date to optimize the performance of the air-sparged hydrocyclone for cleaning fine coal. INTRODUCTION The Pennsylvania Electric Company (Penelec) and New York State Electric and Gas Corporation (NYSEG) have been evaluating advanced fine coal cleaning processes for the production of compliance grade coal (1.2 pounds S02/million Btu). Laboratory bench-scale froth flotation results were compared with results of advanced flotation processes as performed by various organizations, utilizing the same coal feed. Among the processes evaluated, the air-sparged hydrocyclone (ASH) - developed by Dr. Jan Miller at the University of Utah - was considered to offer the best potential for retrofitting into an existing coal preparation facility because of the increased capacity per unit volume. The ASH has been shown to process over 100 times the throughput of conventional froth flotation cells. In May of 1988, Penelec/NYSEG was awarded a contract from the Department of Energy's Pittsburgh Energy and Technology Center (DOE-PETC) to optimize the performance of a five cm (two inch) ASH for producing compliance grade coal from raw classified minus 0.150 mm (1.00 mesh) Upper Freeport coal, and to compare its performance with conventional froth flotation utilizing advanced techniques and selected flotation reagents. The test work is being conducted at EPRI's Coal Quality Development Center (CQDC) in Homer City, Pennsylvania, utilizing a circuit processing 0.10 to 0.25 tons of coal per hour. Other members of the Penelec/NYSEG contract team include the University of Utah, Advanced Processing Technologies, Inc., Davy Dravo, Kaiser Engineers, Ebasco Services, and Management and Technical Systems. ASH DESCRIPTION AND OPERATION The ASH-2 System is a five cm ID (actually 4.76 cm) air-sparged hydrocyclone manufactured by Advanced Processing Technologies, Inc., under license from the University of Utah, for the purpose of research, evaluation and development. A schematic drawing of the air-sparged hydrocyclone is presented in Figure 1. Basically the air-sparged hydrocyclone consists of two concentric right-vertical tubes, a conventional cyclone header at the top, and a froth pedestal at the bottom. The inner tube is a porous tube through which air is sparged radially. The outer nonporous tube simply serves as an air jacket to provide for even distribution of air through the porous inner tube. The slurry is fed tangentially through the conventional cyclone header to develop a swirl flow in the radial direction. Air is sparged through the jacketed, inner porous tube wall and is sheared into small bubbles by the swirl flow. Hydrophobic particles in the slurry collide with these bubbles and, after attachment, are transported radially into a froth phase which forms on the cyclone axis. The froth phase is stabilized and constrained by the froth pedestal, thus moving towards the vortex finder of the cyclone header and discharged as an overflow product. Hydrophilic particles generally remain centrifuged in the slurry phase and are discharged as an underflow product through the annulus created by the froth pedestal.

Jan 1, 1989

By Behrooz Abbasi, Seyedsaeid Ahmadvand, Thom Seal, Babak Azarfar, Bryan Ulrich

Hydro-Jex® is a new enhanced method for heap leach treatment with significantly higher mineral recovery. In this case study at the Los Filos Mine in Mexico, the Hydro-Jex operation is evaluated for heap leach stability. This is pursued by numerical modeling of the heap leach pad stability and well monitoring of the phreatic surface before and after the Hydro-Jex operation. Experimental and numerical results both indicate an improvement in mineral processing under the influence of Hydro-Jex. Numerical results show an insignificant decrease and a significant increase in stability during and after Hydro-Jex injection application, respectively. The integrity of the liner is maintained in both cases. The zonal injection pressure, operationally below the overburden pressure, is found to be negligible compared with the dimensionality of the heap, and stability of the structure is not exposed to any significant risk, even up to 25%above overburden pressure. Furthermore, heap leach factor of safety increases after Hydro-Jex application. This is attributed to breakdown of the water solution build-up and thus a decrease in the phreatic surface depth below the top of the pad. It is suggested that injection wells be drilled, based on thorough geophysical data, in locations where overcompaction of heap material results in water solution build-up and pore pressure enhancement. Compared with traditional heap leaching, the Hydro-Jex technique not only expedites mineral processing by increasing chemical kinetics extraction but also increases the stability of the heap by unclogging drains.

Jun 29, 2020

By C. M. Bristow

The mineral kaolinite is one of the commonest minerals in the uppermost 10 m of the continental crust; ranking in abundance alongside minerals like quartz, mica, feldspar and calcite. Only very exceptionally does it possess all the necessary properties needed to make it worth commercially exploiting. The terms 'Kaolin' and 'Kaolinite' are derived from a locality known as 'Kau-ling', in Jiangxi Province, Peoples Republic of China; where samples of a white clay used by the Chinese to make porcelain were first obtained by European missionaries and explorers in the eighteenth century.

Jan 1, 1986

By Ed Schodowski

Wireless technology is a hot topic for anyone involved in the design, operation, maintenance or upgrading of mines or mineral processing plants because wireless technologies overcome barriers that have prevented many useful data inputs. Wireless communications can contribute to worker safety, satisfy environmental concerns, support plant security, track human and physical assets, and improve equipment maintenance. The cost structure of wireless is compelling and users can realize savings ? up to 90 percent less installed cost than wired instruments ? since wireless technology eliminates the need for expenses associated with cabling, engineering, construction and documentation. Many applications previously considered too expensive have become economically feasible with wireless. Two examples are continuous monitoring of safety showers to notify operators when one has been activated, and monitoring effluents to ensure environmental regulations are being met. In many cases, wireless transmitters can be installed where wired devices were too expensive to justify, or were not feasible due to physical or technical barriers. Examples include monitoring temperature measurements inside a rotating reactor or monitoring process variables in a tough, corrosive environment too challenging for a wired solution. Wireless also gives operating personnel mobility with the ability to communicate from remote or hard-to-reach zones. According to a recent Venture Development Corp. survey covering radio frequency (RF) of microwave industrial monitoring and control products, these features are contributing to the expected nationwide growth rate for industrial wireless applications of 19 percent annually from 2007 to 2012 (Taylor, 2008). At the same time, mineral producers have many questions about wireless systems including their applicability, reliability and security in this industry. Just what can wireless do? Is it secure and reliable? Can these instruments stand up to the rigors of the industry? Can wire-less technology provide the flexibility needed for mining applications?

Jan 1, 2009

By B. K. Mishra

This paper focuses on the use of a numerical tool known as the discrete element method (DEM) to study the motion of ball charge in ball mills (14-18 ft). DEM is employed to simulate the motion of individual balls. While doing so, the effect of liner design on the grinding performance of the mill is studied. Two important factors such as the configuration of the liner and the geometry of the lifting surfaces are correlated with the overall mill performance. An attempt is made to show the effectiveness of the lifter bars in transmitting power from the mill shell to the interior of the mill with particular emphasis to large diameter mills.

Jan 1, 1992

By J. A. Ehler

Speed and torque control of standard A.C. induction motors can be accomplished using a variety of devices ranging from mechanical, hydraulic, and electrical. Also, the motor can be specified as an A.C. wound rotor or D.C. motor using the associated controls. Normally, any one of these drive types can be adequately used to provide the torque control necessary to accelerate a conveyor belt system. The selection will depend on the economics, experience, and preference of the designer or end user. These drive types will be presented from a functional and performance viewpoint to assist in the understanding of the available technology.

Jan 1, 1998

By Rameshwar Sah, PK GHORUI, LR SINGH, SIVALINGARAJU BARISETTY, SHYAM YADAV

Fly ash is a by-product generated by the combustion of coal in thermal power plants. Its disposal is a major environmental concern for these power plants. Though a considerable part of fly ash is used in cement making and brick manufacturing, a substantial quantity remains unutilized. Bentonite is commonly used as binder in the micropelletization of process waste to attain the mechanical strength required for handling and transportation. The present paper deals with the partial replacement of bentonite with fly ash in the micropelletization process without affecting the quality of the micropellets. The mechanisms of both the binders are discussed. The bonding of particles by bentonite is a physical mechanism, while fly-ash bonding is a chemical mechanism. Silica and alumina are the major constituents present in fly ash along with lime. In the presence of water, the alumino-silicates and unhydrated lime present in fly ash undergo a pozzolanic reaction and form cementitious bonds, which hold the particles together. Use of fly ash as alternative binder for bentonite has cost benefits besides providing a better utilization option for fly ash.

By Zhongran Dai, Nan Hu, Jianhong Ma, Hui Zhang, Zhihua Zhong, Han Zhou, Feng Li, Yonggen Qiu, Yang Ding, Yingchun Yang, Dexin Ding

In the traditional chlorination roasting-water leaching-solvent extraction process for the extraction of rubidium-bearing ore, Rb leaching from the ore and calcium removing from the leachate are conducted separately, and this results in the complicated process and high energy consumption. In order to integrate the Rb leaching and calcium removing processes, Rb-bearing polymetallic ore was firstly treated by chlorination roasting, it was then leached in a micro-reactor with raffinate, and the calcium ions in the leachate were removed in the reactor as carbonate precipitates by passing CO2 at certain pressure into the reactor. The effects of raffinate alkalinity, CO2 pressure, and CO2 reaction time on Rb leaching rate and calcium removing rate were investigated. The experimental results show that when Rb-bearing polymetallic ore was leached for 90 min by stirring with raffinate with 1.125-mol/L alkalinity, and the pulp was made to react with CO2 at 0.8 MPa for 15 min, the Rb leaching rate and calcium removing rate amounted to 92% and 98.2%, respectively. This integrated process including Rb leaching from Rb-bearing polymetallic ore and calcium removing from leachate could simplify the process for the extraction of Rb-bearing ore and increase its economic benefits.

Sep 27, 2023

By Rainer Antretter

While respirable crystalline silica (RCS) dust that arises in industrial production mostly emanates from point sources and can be well mitigated, the extraction of dust is much more difficult in underground construction, since locally generated dust spreads widely. Analysis of dust measurements shows that RCS values are difficult to predict, and effective dedusting systems are required to comply with permissible exposure limits (PEL) in breathed air. Dedusting systems are effective near the tunnel face, while dedusting of working areas away from the tunnel face is difficult or even impossible. In general, there is little temporal influence on the tunnelling work—except for drill and blast excavation—which makes it necessary to remove the deduster and ductwork from the face area. Concurrent work in the tunnel is affected by the backflowing air mass of ventilation and therefore the quality of this air mass must be considered. The use of personal protective equipment (PPE), e.g., dust filter masks, is considered the least-desirable safety measure available. However, for certain individual operations in the tunnelling process, the use of PPE cannot be avoided, especially if other technical mitigation measures are not possible. In tunnels with small cross sections for example, dedusting systems often cannot be accommodated and PPE must be used instead. This raises the question of whether the use of PPE can be avoided by designing appropriate excavation cross sections and allowing for the implementation of technically engineered mitigation measures. The paper highlights problems with dedusting measures and shows possible ways to achieve OSHA compliance.

Jun 13, 2021

By L. Alan Weakly

The U.S. Department of Energy (DOE) has entered into a $l.5 million Cooperative Agreement with Alpine Equipment Corporation/Astro International Corporation ("Alpine") of State College, Pennsylvania, for the evaluation of water-jet-assisted (WJA) mechanical cutting of oil shale under actual mining conditions. A commercial-sized, heavy WJA mechanical miner is being assembled based upon the successful "factory testing" of a smaller prototype miner utilizing standard tungsten-carbide and Polycrystalline Diamond Composite (POC) bits in large oil shale boulders. Actual field testing of the machine will be conducted in an oil shale mine located in the Piceance Basin of Western Colorado. In-mine logistical support is being provided by several oil shale companies through the Colorado Mining Association (CMA) and the U.S. Bureau of Mines (USBM).

Jan 1, 1990

By V. K. Gupta

The experimental results of some wet batch and continuous grinding experiments carried out in a 40 x 40 cm grate discharge ball mill have been analyzed for the variation of the grinding rate parameters, Si, with various operating conditions using a linearized population balance model. The wet grinding tests were carried out under conditions which were very similar to those encountered in the actual practice in plant operation. Well distributed -4 and -20 mesh feeds of two complex pyritic ores were used. The volume-percent solids in the pulp ranged from 30-40, the particle load from 5-8 kg, and the solids feed rate from 70-1 10 kg/hr.

Jan 1, 1981

By E. Westman

Geographic Information Systems (GIS) are becoming a more commonly used tool for resource estimation as they provide not only a database management platform, but also the graphical capabilities to visualize resource characteristics. Interpolation methods used commonly in these resource studies do not typically provide a quantitative answer to the question: "How accurate is the estimate?" By comparing localized measurements at several locations to the interpolated thickness distribution used in a resource estimate, a quantitative analysis of accuracy can be obtained. The technique is demonstrated with a case study from Central Appalachia.

Jan 1, 1999

By G. C. Kachel

Significant effort has been expended and considerable success has been realized m the application of instrumentation and automatic control equipment in the mining and ore processing industries. This effort has been applied principally to process equipment with the objective of increasing throughput, minimizing labor requirements and/or improving grade or product quality. Less spectacular, but quite rewarding has been the successful application of instrumentation and automatic control equipment to a wide variety of material handling equipments. This paper describes some of this work including: (1) automatic weighment of load-haul-dump units and trams underground; (2) automation of skip loading; (3) instrumentation applied in feeders and conveyors; (4) level measurement in bins, silos, vessels and sumps; (5) automatic blending of sized materials; (6) automatic loading of ships, trains and trucks; (7) automatic control of tailings disposal facilities

Jan 1, 1973

The last decade has seen the use of powerful computerized Mine-Wide Monitoring (MWM) systems for detecting hazardous conditions in underground coal mines. Recently, the U.S. Bureau of Mines and Jim Walter Resources, Inc. (JWR) expanded the scope of MWM system to include ground control. Single-point extensometers were installed in each of 30 intersections along a tailgate entry. These instruments monitored the rate of roof sag, a sensitive indicator of roof instability. Data were collected by the mine's own computerized MWM system. The paper describes the successful integration of ground control instruments into MWM, the data reduction procedures, and the identification of several hazardous areas.

Jan 1, 1994

By J. O. Stephens

During the late 1940's and early 1950?s, the Westinghouse Combustion Turbine Division built and demonstrated a residual oil-burning locomotive on six eastern railroads. Plans were made to convert to burning pulverized coal, and a single combustor was operated at a full-pressure condition in the laboratory for about two years. During the mid-1960's to mid-1970's, there was considerable interest in coal-burning MHD and a combustor was developed which would also be applicable to combustion turbines. In the early 19801s, the BCR National Laboratory (BCRNL) became affiliated with the University of Pittsburgh, and a program was begun, supported by the Stare of Pennsylvania, to develop an all-purpose combustor for use with industrial and utility boilers and eventually with combustion turbines. In this paper, we review the work of almost 40 years, indicate our present position, and propose steps to be taken leading to efficient and environmentally acceptable power generation from coal, and specifically to coal-burning locomotives.

Jan 1, 1986

By Andrew B. Cecala, Emily J. Haas, Jay F. Colinet

Researchers from the U.S. National Institute for Occupational Health and Safety (NIOSH) studied the impact of an unregulated dust control technology (the Helmet-CAM) and a regulated dust control technology (the continuous personal dust monitor) within a sociotechnical system (STS) framework to mitigate respirable dust sources. The results address how to best incorporate the overarching principles of meta-design STS during the technology integration process. Specifically, quantitative and qualitative data show that a prominent focus on the social factors within an STS framework could help reduce organizational unpredictability and may improve communication within the system to help reduce technology adoption time.

By D. J. DeLeo

In recent years the hue and cry of American industry concerning the pressure of foreign competition on the domestic marketplace has become all too familiar to most of us, as we are all well aware, the steel industry has not been exempted from this pressure, reduced production levels, work force cutbacks, and in some extreme cases, plant closings and company liquidations have resulted, new regulations governing imports and quotas have been enacted, foreign trade agreements reached, and more strict regulation enforcement practices undertaken, despite these, and other measures, the impact of aggressive foreign competition has not lessened, the concensus of numerous management consultants is that in order to successfully cope with these problems we must draw on all available technology to provide the tools which will enable us to enhance our management effectiveness, one area requiring particularly close attention in any mining operation is that of managing critical resources - namely time, energy and equipment in a fast and efficient manner, In mining, with critical resources deployed over a large geographical area, any degree of success involved with resource management is dependent upon knowing the current status of all work related activities, if we, as mine operators, are to be more successful in this area, additional tools are a necessity and modern technology has provided a multitude of new options from which to choose.

Jan 1, 1985

By J. L. Hoover, P. W. Conrad, J. Downey, S. Parrow, S. Rosenthal

The goal of the drill bit consumption study was to develop an equation(s) based on various components that affect drill bit wear and use that equation(s) to estimate the consumption of bits during production drilling. Drill bit data from various geographic locations were compiled and used to develop linear regression equations using the Microsoft Excel software package. Multiple drill bit consumption equations were developed and statistical analysis was used to verify the accuracy of those equations. The equations will allow mining companies to more accurately forecast drill bit consumption when evaluating new mine properties. This capability becomes increasingly beneficial to forecasting as the cost of consumables increases.

Jan 1, 2012

By T. S. Golosinski

Use of contractors to excavate, load and haul mined material is widespread in Australia. It is also becoming a common practice in many other countries. The paper reviews current practices in Australian contract mining. Various types of contracts are reviewed, including partnering arrangements and alliancing between the contractor and the mine owner. Applicability of various types of contracts to specific mining situations is discussed, as is their impact on overall mine performance

Jan 1, 1998

By E. H. Smith

St. Joe Minerals Corp., a subsidiary of Fluor Corp., treats high-grade gold, silver, and copper ore at its El Indio plant at an altitude of 4 km in the Chilean Andes. The ore is complex, being a mixture of massive pyrite-enargite and quartz, both containing very fine gold and silver. Treatment produces a copper flotation concentrate containing high levels of gold, silver, and arsenic, and also dore bullion. Part of the flotation concentrate is roasted to remove the arsenic content, and arsenic trioxide is collected as a by-product.

Jan 1, 1987