Search Documents

By T. L. Barone, J. R. Patts, L. D. Patts, S. J. Janisko

"Controlling float coal dust in underground coal mines before dispersal into the general airstream can reduce the risk of mine explosions while potentially achieving a more effective and efficient use of rock dust. A prototype flooded-bed scrubber was evaluated for float coal dust control in the return of a continuous miner section. The scrubber was installed inline between the face ventilation tubing and an exhausting auxiliary fan. Airborne and deposited dust mass measurements were collected over three days at set distances from the fan exhaust to assess changes in float coal dust levels in the return due to operation of the scrubber. Mass-based measurements were collected on a per-cut basis and normalized on the basis of per ton mined by the continuous miner. The results show that average float coal dust levels measured under baseline conditions were reduced by more than 90 percent when operating the scrubber. IntroductionAirborne coal dust is a byproduct of coal production, and engineering controls exist to deal with both the respirable dust health hazard as well as the float dust explosion safety hazard. Float coal dust, smaller than 75 µm (0.003 in.) in size, can deposit throughout mine entries and propagate explosions that had been initially fueled by methane gas. The inertization of float coal dust with rock dust helps prevent a potential secondary float coal dust explosion, but a preferable course of action is to significantly reduce the hazard by removing float coal dust from the airstream before it has the opportunity to deposit on the mine’s surfaces.Since 1970, disasters due to explosions in underground coal mines have caused 201 deaths in the U.S. mining industry, including 29 deaths in a single mine explosion in 2010 (Wade, 2010; U.S. Mine Safety and Health Administration, 2015). The U.S. National Institute for Occupational Safety and Health (NIOSH) had initiated a fiveyear research project that aims to investigate methods and technologies to reduce the potential for secondary coal dust explosions by the purposeful capture and/or suppression of float coal dust prior to its deposition on the mine roof, rib and floor (NIOSH, 2013). The project aims to evaluate the efficiency of methods to reduce longwall and belt airway float dust in the general airstream as well as methods to capture it at or near the source. Prioritization is given to longwall sections given the amount of coal produced relative to continuous miner sections, but the research is open to technologies that may be adapted from one method of mining to another."

Dec 1, 2016

By S. Khoshjavan

Separation of refractory rock phosphate (P2O5 = 11.5%) from the Dalir area, Iran, containing quartz, calcite and other impurities, by calcination and flotation processes has been successfully used to upgrade the phosphate values. Petrographic studies of this ore showed that collophanite was the major phosphate mineral and the main gangue minerals were calcite, dolomite and quartz. The results of characterization studies showed that the liberation degree of apatite occurred below the average grain size of 140 µm. Preliminary flotation tests were used to process the phosphate samples. Results of preliminary flotation tests showed that they don?t contain any desirable efficiency (grade or recovery) of P2O5. Calcination was the best process for preconcentration of this ore. In the desliming stage, about 14.4% of total P2O5 was removed. Encouraging concentrate grades were obtained after flotation with anionic and cationic flotation, successively. The reagent schemes that have been used in this study consisted of COCO-amine acetate and fatty acid as silicate and apatite collectors, respectively, as well as fuel oil and anionic poly acryl amid as promoter collectors. The optimum pH values for direct and reverse flotations of phosphate were 11 and 6, respectively. Experiments conducted using d80=140 µm deslimed fractions has yielded an acceptable grade of more than 30% P2O5 with a recovery of more than 62%. Finally, a laboratory flowsheet for the processing of Dalir refractory phosphate ore has been proposed.

Jan 1, 2011

By M. P. Saunders

A comprehensive, site specific water management plan is of primary importance to the successful implementation, operation and decommissioning of any mining project. Formulation of a plan requires an orderly planning process consisting of identifying problems, establishing planning criteria based on the guidelines and requirements of regulatory agencies, and an iterative procedure of identifying, investigating, and evaluating plan elements and alternative plans. A typical uranium surface mine operation consists of a mine pit or pits, spoil pile areas, crusher, processing plant, and tailings disposal area. A water control plan addresses the problems of diversion of natural runoff from undisturbed areas around the mine; and diversion, collection, and treatment of runoff from within the mine area. A water control plan is required to determine the location and size of appropriate control and detention structures; their cost; and the schedule for permit activity, design, and construction. The plan must be formulated to meet the requirements of both the State and Federal regulatory agencies.

Jan 1, 1981

By J. Rostami, P. P. Nelson, A. Khetwaln

Tunnel boring machines (TBMs) can be considered as the method of choice for tunneling in many projects due to the high level of efficiency and high potential productivity, safety, and applicability in a variety of subsurface conditions. The muck transportation system in a TBM tunneling operation plays a significant role in the process and impacts the overall performance of the machine. This paper introduces a recently developed method of simulating TBM operation through discrete event simulation (DES), which allows for tracking of the various activities, incurred downtimes in the operations, and overall machine utilization. The study presented here compares two different muck transportation systems, conveyor and rail, under similar geological conditions to quantify the impacts of the choice of muck transportation systems on machine utilization. The results show the applicability and extent of redundancy in the use of the two systems relative to machine capabilities and their sensitivity to geological conditions.

Jun 13, 2021

WELCOME to the world-class Cripple Creek district where gold exploration and production continue 95 years after the initial discovery. More than 21 million troy ounces of gold have been recovered, valued at greater than $7.8 billion using today's gold price ($371/oz). The Cripple Creek district is localized within and around the margins of a silica-undersaturated alkalic diatreme-intrusive complex. The diatreme appears to be comprised of three sub-basins: 1) a sub-basin east of the Cresson (Fig. 1); 2) a southwestern sub-basin between Victor and Cripple Creek; and 3) a northwestern sub¬basin within which the Globe Hill and Ironclad pits (Fig. 1) are located. The recognition of three separate basins was made by G. F. Loughlin and A. H. Koschmann (1935, Fig. 8) who prepared a contour map on the floor and walls of the composite Cripple Creek basin. The northwestern and southwestern sub-basins are apparent due to the discontinuous exposures of a partially exhumed ridge of Precambrian rocks (Fig. 1). The separation of the eastern and southwestern sub-basins was recognized in mine exposures where a fault-bounded ridge line extends from the vicinity of the Ajax mine toward the Precambrian "island" (Fig. 1).

Jan 1, 1986

Little knowledge is available that considers the effects of continuous miner position on the possible respirable dust exposure of the remote mining machine operator. Such information could be very useful for increasing the awareness of the remote operator as to those parts of an extended cut that generate higher levels of respirable dust. This data could be used to develop guidelines for positioning the remote operator to reduce his potential exposure. This work details the effects of continuous miner position on dust levels measured on the machine and at the remote continuous miner operator location.

Jan 1, 1998

By Ray H. Hario

Background of Erie Mining Company Erie Mining Company, managed by Pickands Mather & Co., is one of the largest producers of iron ore pellets in the United States. The plant is located at Hoyt Lakes, Minnesota, sixty-five miles north of Duluth on the eastern end of the Mesabi Range. Taconite Harbor, situated on the north shore of Lake Superior, is the location of its Power Plant and shipping facilities. (Figure 1) Even though the plant commenced operation in September, 1957, its true be-ginning can be traced back to 1931 when Pickands Mather, in conjunction with Bethlehem Steel Corporation and Youngstown Sheet and Tube Company, began investi-gating the possibilities of processing low grade ores. In 1940, Erie Mining , Company was formed. During the early and middle 1940's, laboratory and pilot plant research was proven to a point where a preliminary plant was deemed feasible and built in 1948. This plant had an annual capacity of 203,200 t (200,000 long tons) per year and, until mid-1952, was the only taconite plant in existence using commercial-size equipment. During this period, ownership of Erie Mining Company was expanded to include Interlake, Inc. and The Steel Company of Canada, Limited. In 1953, authorization was obtained from the owners to build a 7.62 M t (7.5 M long tons) per year plant at a cost in excess of $300,000,000.

Jan 1, 1977

By D. Yeager

Researchers at the U.S. Bureau of Mines have successfully used a genetic algorithm to tune computer models of three column flotation units simulating a separation circuit. The computer models rely on empirical constants that are selected so that the models accurately predict the performance characteristics of individual column flotation units. Unfortunately, these empirical constants have traditionally been selected using a time consuming trial and error process. A new and more efficient approach to selecting empirical constants for computer models has been developed. A genetic algorithm has been used to select the empirical constants for column flotation models used to simulate a three column circuit. Genetic algorithms are search algorithms based on the mechanics of natural genetics. They rapidly locate near optimum solutions in difficult search spaces. Bureau researchers have used these innovative search algorithms to dramatically reduce the time needed to select empirical constants for column flotation models. The approach is applicable to the selection of empirical constants for numerous other computer models.

Jan 1, 1995

By Glenn Mongillo

Discrete Element Method (DEM) software has been successfully used to simulate various machine/soil interactions and provide insight for industries such as mining and bulk material processing. This paper will investigate typical calibration techniques used in particle models for DEM simulation and physical calibration experiments with soft ground TBM cutting tools to incorporate parameters such as tool drag forces that contribute to required TBM torque. With a well calibrated DEM model, it is expected that TBM simulation results will be more meaningful and provide better insight into TBM performance, power requirements, cutting tool placement, and overall cutter head design.

Jun 13, 2021

By Qinghua Tian, Zhipeng Xu, Dong Li, Xueyi Guo, Liu Zhu

A possible process for extracting tellurium and antimony from a residue generated in alkaline sulfide leaching of telluriumbearing alkaline skimming slag was proposed. The central composite design was employed to define the optimal leaching conditions for tellurium and antimony extractions from the residue sample. Using a 23 factorial matrix, the best performance for tellurium and antimony extractions (96.36% and 99.64%) were obtained at 175 g L−1 Na2S concentration for 80 °C during 60 min. The notable degree for influencing tellurium and antimony extractions was leaching temperature, Na2S concentration, and leaching time. The analysis of variance results indicated that the regression model was significant and suitable to be used for the optimization of independent variables within the range. The model was validated under optimal operating conditions based on the experimental design results. Antimony and tellurium in the leach liquor were separated and recovered by H2O2 oxidation followed by Na2S-Na2SO3 reduction. 98.93% of antimony was precipitated selectively during H2O2 oxidation, while 95.06% of tellurium was precipitated during Na2S-Na2SO3 reduction. NaSb(OH)6 and elemental tellurium was obtained as the product.

By M. Frenzel, D. Ebert, K. Bachmann, A. D. Renno, R. Möckel, J. Gutzmer, J. Krause

With the increasing demand for metalliferous and mineral raw materials, and consequent depletion of the global natural resource base, the possible utilization of secondary raw material sources is receiving more and more attention. In the present study, we present results from a detailed vanadium deportment study of three basic oxygen furnace slag (BOS) samples known to containing elevated bulk concentrations of vanadium (V). Complementary analytical methods that were used to quantify the abundance and composition of V-containing phases include SEM-based automated mineralogy, Xray fluorescence (XRF) analysis, and X-ray powder diffraction as well as electron probe microanalysis. The vanadium deportment was quantified using Monte-Carlo simulations of the data obtained from automated mineralogy and electron microprobe analysis. The total V concentrations identified by XRF are between 1.7 and 2.2 weight percent V. The most important hosts of vanadium are larnite-, brownmillerite- and portlandite-solid solutions. In two samples, calcium carbonates also significantly contribute to the V deportment, while wuestite, lime and native iron do not contribute significantly to the vanadium deportment. A thorough consistency check identifies considerable uncertainties in the density of the Vbearing phases as the most likely reason to explain remaining discrepancies between measured and calculated V values.

Aug 1, 2024

By Matthew Anderson, David Day, Paul Smith

"The Midwest is presently the focus for Combined Sewer Overflow (CSO) abatement in the United States (U.S.). Most of the EPA mandated utility and municipal long term CSO abatement programs in large metro areas in the Midwest such as Cleveland, Indianapolis, Columbus, Chicago, St Louis, Akron, Fort Wayne, Louisville, Kansas City, Omaha and Pittsburg use or will use deep tunnels for storage and conveyance of CSOs. This paper will compare design methods specified and implemented for tunnel construction in Midwestern geology such as soft ground and mixed face EPBM tunnels, hard rock TBM tunnels, drill & blast tunnels, road header tunnels along with tunnel lining systems. It will also review the performance of successful CSO systems that include design life cycle, vortex and drop shaft configurations, pump stations, storage and conveyance strategies and long term operation and maintenance criteria. HISTORY and BACKGROUND Prior to development of mandated wastewater treatment plants, collecting both wastewater and storm water runoff in a single-pipe system was an efficient and economical solution. The early combined sewer systems were typically designed and sized to carry several times the average dry weather wastewater flows and not designed to handle a mixed volume of waste water and storm water during a wet weather event. Beginning in the early 1970s, federal legislation (Clean Water Act of 1972, Clean Water Act of 1977 and the Water Quality Act of 1982) changed how municipalities and industries in the U.S. were required to treat and discharge wastewater into the nation’s surface waters. They were mandated to treat wastewater at federal regulatory standards for discharge into surface waters that is safe for humans, wildlife and aquatic life. The wastewater treatment facilities that evolved were initially designed and sized to treat only the peak volume of raw wastewater flowing during dry weather. Combined sewer system control sections or relief structures were installed upstream of wastewater treatment plants (WWTP) and were designed to protect WWTPs from potential damage that would be caused if peak volumes of raw wastewater mixed with storm water runoff reached and overwhelmed the WWTPs."

Jan 1, 2016

By Lynn Salvati, Colin LaVassar, Loic Galisson, Joel Theodore, Lynette Sla

"Sound Transit’s University Link and Northgate Link projects will add 6.75 miles (10.9 km) of twin-bored tunnel to Seattle’s light rail system, extending the route north from downtown Seattle. The tunnels are being constructed primarily in glacial soils using pressurized-face tunnel boring machines. Cover over the tunnel alignment varied from 13 feet to over 300 feet (4–91 m). Since the tunnels are located in densely populated urban areas, controlling ground movements and monitoring settlement were essential to success of these projects. Hundreds of geotechnical instruments, including extensometers, surface settlement points, and near-surface settlement points, were used in both projects to monitor settlement. The observed data were compared to settlement predictions made prior to tunneling, and analyses performed to update empirical factors to better estimate settlements. Recommendations for designing efficient and cost-effective settlement monitoring programs are provided based on the review of the monitoring data and analyses.INTRODUCTIONThe paper includes data from Sound Transit’s University Link and Northgate Link projects. These projects will add 6.75 miles of twin-bored tunnel to Seattle’s light rail system. The tunneling for University Link will extend the light rail system from downtown Seattle to the University of Washington. Tunneling from downtown Seattle to the Capitol Hill Station was completed under the U230 contract, and tunneling from the Capitol Hill Station to the University of Washington Station was completed under the U220 contract. The Northgate Link extension will extend the light rail line north of the University of Washington, including approximately 3.5 miles (5.6 km) of twin tunnels between the University of Washington Station and the Maple Leaf Portal and two stations, U District Station and Roosevelt Station. Tunneling for the Northgate Link project is still underway as part of the N125 project. At the time of writing, tunneling from the Maple Leaf Portal to Roosevelt Station has been completed. Therefore data labeled as N125 in this paper only include the portion of the alignment from the Maple Leaf Portal to Roosevelt Station."

Jan 1, 2016

By G. W. Kenzy

Recently, in the United States, questions of possible deleterious synergistic health effects of the gaseous and particulate components in the diesel exhaust and mineral and coal dust have been the impetus for extensive research by several agencies. At the present time, diesel engines are tested and approved for use in gassy and non-gassy underground metal and non-metal mines under Parts 31, 32, and 36 of Title30 of the Code of Federal Regulations. Diesel-powered equipment for use in underground coal mines, though not explicitly addressed in the law, is administered under Parts 32 and 36 of Title 30, with Part 36 being applied in the case of equipment working inby the last open crosscut or in the return airways. Operation of diesel equipment in underground mines has the potential for serious health and safety hazards from the gases, vapors, and particulates in the exhaust. Therefore, various countries have rules and regulations for the safe deployment of diesel equipment. The applicable laws and regulations from several countries who have long experience with diesel-powered equipment in their mines are reviewed. Four major areas have been addressed: (1) testing and approval procedures of diesel engines, (2) ambient mine air quality specifications, (3) frequency of sampling and location of samples, and (4) air quality specifications in splits where diesel-powered equipment are operated. The review indicates that most regulations generally consider four possible hazards: (1) toxic components in the engine exhaust, (2) ignition of flammable atmospheres by the engine or electrical equipment, (3) fire hazards presented by the engine fuel oil and by combustible material that might come in contact with the equipment, and (4) mechanical hazards. There is a remarkable similarity in the laws with regard to engine design, testing and approval procedures. However, the aspects with regard to mine air quality and quantity are quite variable-- from a general statement to very specific standards for many different diesel exhaust constituents. However, the laws with regard to synergistic effects of diesel exhaust components and other mine air contaminants are an exception.

Jan 1, 1980

By J. F. Fitzpatrick

This paper examines the cost elements associated with changes to gold mining practice over the last decade that result from the changes in environmental regulation and the heightened governmental and public awareness of environmental issues. The main experience base is Pegasus Gold Corporation's flagship mine, Zortman/Landusky, located in the Little Rocky Mountains of Phillips County, Montana. This operation was among the first mines that were permitted under the 1974 Montana Metal Mining Reclamation Act. In 1974, the Montana Metal Mine Reclamation Act was enacted, creating a permit system for metal and industrial mineral mines for the state of Montana. The act established the content of mine permit applications and defined parameters for the reclamation of mining disturbances. The Act can be viewed as implementing legislation for Article 9, Section 2, of Montana's Constitution, which provides that "all lands disturbed by the taking of natural resources shall be reclaimed." Pegasus Gold Corporation's Zortman/Landusky mine was among the first mines permitted under the new Act. In 1978, the initial permit applications were submitted for Zortman and Landusky, and a full Environmental Impact Statement was prepared by the Montana Department of State Lands; permits were issued in 1979. When opened later that year, the anticipated mine life for the combined Landusky and Zortman operations was approximately 18 years, based upon a proven and probable ore reserve of 43.2 million tons. Zortman/Landusky was the first large-scale heap leach gold mine in the United States. Its distinguishing feature was, and remains, a remarkably low ore grade, now .016 oz/ton. The ore is economic because it requires neither crushing nor agglomerating to leach effectively. Approximately two years after the initiation of the state's regulatory process, the Federal Land Policy Management Act (FLPMA) was enacted, establishing a mine regulatory framework for lands under the administration of the Bureau of Land Management.

Jan 1, 1992

By Timothy Batchler, Khaled Mohamed

Standing supports have been used in coal mines for decades to enhance roof support capability. Sometimes standing supports are used as a tool to resist the lateral movement of spalled ribs. Researchers from the National Institute for Occupational Safety and Health (NIOSH) are conducting a testing program for different types of standing supports (steel and timber) to investigate the effect of lateral loading on their vertical loading capacities and the factors affecting their lateral loading capacities. In this paper, the mine roof simulator (MRS), at the NIOSH Pittsburgh research facility, was used to determine the response of steel props to vertical and horizontal loadings. Finite element models (FEMs) were developed and verified using the tested steel props. To justify the testing program for testing standing supports with end-conditions of rock-like materials, the verified prop models were used to study the effect of a wide range of roof and floor materials (gray shale, shale, and claystone) on the critical buckling loads of the steel props. Also, several lateral loading scenarios were evaluated in which the steel props were laterally loaded at different heights. The critical buckling load for steel props setting up against a claystone roof and floor was found to be one-half of that shown by the MRS test where roof and floor platens are made of steel. Minimum prop performance was observed when the lateral load was applied at the mid-height of the steel prop, especially at small lateral displacement (less than 2 in).

Sep 10, 2022

By S. Partney

Waste clay ponds are a necessary part of the phosphate rock beneficiation process. They are large, averaging a square mile in size; unsightly, in that they protrude 20 to 50 feet (6 -15 meters) above natural grade; stabilization and reclamation is slow; and they have had a history of catastrophic failure. The State of Florida has never published a specific rule regarding the configuration or height of these ponds, but has enforced numerous policies along these lines. The current rules are given and interpreted, along with the reasoning for current policy. In addition, an overview of the history of the policies, and an attempt at explaining the reasons for the changes that have occurred is given. The industry has been forced to make major monetary decisions, having effect for decades on mine economics, in a constantly changing regulatory environment. The Bureau of Mine Reclamation is confident that a direction of regulation has been solidified, but changes are still to be anticipated.

Jan 1, 1998

By J. R. Patts, A. B. Cecala

"After industrial sand has been mined and processed, the finished product is typically loaded into small bags of 45 kg (100 lb) or less, large bulk bags of 454 to 1,361 kg (1,000 to 3,000 lb), or vehicles such as trucks or trains for transport to end users. As the sand is being transferred and loaded, dust can be released into the work environment, potentially exposing workers to respirable crystalline silica. A number of control technologies have been developed and utilized in an effort to reduce dust liberation during loading operations. For bulk loading into trucks or trains, the U.S. National Institute for Occupational Safety and Health (NIOSH) evaluated one of these technologies, the Dust Suppression Hopper (DSH), at two industrial sand processing plants. Results from these case studies show that the DSH reduced airborne respirable dust levels by 39 to 88 percent, depending upon the product size being loaded.IntroductionInhalation of respirable crystalline silica dust can lead to the development of silicosis, a disabling and potentially fatal lung disease. Once contracted, there is no cure for silicosis, so the goal is to prevent the development of the disease by limiting exposure to respirable dust containing crystalline silica at or below the exposure limit of 50 µg/ m3 recommended by the U.S. National Institute for Occupational Safety and Health (NIOSH, 2002). At industrial silica sand operations, the product contains high levels of crystalline silica, so effective control technologies are needed to minimize the respirable dust exposure of workers.NIOSH, in partnership with the Industrial Minerals Association–North America, published a dust control handbook (NIOSH, 2012) focused upon control technologies for industrial- mineral mining and processing operations. One chapter in this handbook discussed technologies for controlling dust liberated during bulk loading, including telescoping loading spouts, dust collection systems for loading spouts, enclosures for load-out areas and a newer technology known as Dust Suppression Hopper (DSH)."

Jan 9, 2018

By M. K. Mohanty

Due to inefficiencies of the flotation process, significant effort has been recently provided to develop gravity separators for treating ultrafine particles. As a result, several enhanced gravity concentrators have been developed and commercialized. The Altair Centrifugal Jig is an enhanced gravity separator that provides relatively efficient separations on +25 µm size fractions. An experimental program conducted on -600 µm coal found that the Altair Jig reduced the ash content of the 600 x 44 µm from about 30% to 10% with an 86% combustible recovery value. The pulse water pressure, feed volumetric rate and ragging volume were found to be the key operating parameters affecting the separation performances obtained from the process. An extremely low density cut point of 1.54 and an Ep value of 0.08 were indicative of the high process efficiency values achievable by the Altair jig.

Jan 1, 1998

By T. Gupta, T. Ghosh

Rare earth elements (REEs) and their compounds are essential in a multitude of mundane and sophisticated applications such as renewable energy technologies, catalysts, medicine, and defense applications. The global supply deficit could be attributed to the destabilization of REE market that has, as a result, incentivized indigenous production of REEs. Cost-effective and environmentally benign opportunities are being explored for the production of REEs from non-conventional mineral sources including coal and coal by-products to stabilize the supply chain. Coal from Healy coal mine and Wishbone Hill deposits in Alaska have been quantified for REEs and were found to possess elevated total REE concentrations as compared to world average levels (60– 70 ppm). The objective of the study was to concentrate the REEs in the froth phase by froth-flotation of the fine size fraction (< 75 μm). A Box-Behnken design of experiment was employed to ascertain the main and interaction effects of operational parameters on response variable by analyzing 3D response surfaces. Experiments were carried out to maximize REE recovery and concentration by modeling and optimization of three operating variables (frother dosage, pulp density (% solids), and collector dosage). Based on the results, the optimum flotation conditions for maximum recovery at an elevated concentration of REEs in the froth fraction was obtained at 4.2% solids and 32.7 ppm of frother dosage for Healy sample and 10% solids and 37.9 ppm of frother dosage for Wishbone Hill coal sample. The quadratic relationship between the input and response variable was found to be independent of collector dosage suggesting good surface hydrophobicity and floatability of the two coal samples.