Search Documents

By R. Fields

Nevada is primarily known today for its nation-leading production of gold and silver. However, industrial mineral production continues to play an important role in providing construction materials to help make the state the fastest growing in the United States. Aggregate production in Nevada was about 20 million tons in 1991. Most of that was used in construction in the fast-growing Las Vegas area. The state leads the nation in the production of barite and mined magnesite and has significant production of lithium carbonate, diatomite and gypsum. Other industrial minerals produced in the state include specialty clays, silica, lime and dolomite and relatively small production in salt, perlite and dimension stone. Industrial minerals operations are subject to state and federal permitting requirements, especially in the areas of air and water quality and mined land reclamation. As in all segments of the mineral producing industries throughout the nation, the amount and complexity of regulations affecting industrial minerals has increased significantly in recent years. Nevada is no exception.

Jan 1, 1993

Thermal pretreatment can significantly improve industrial comminution operations by reducing energy requirements and increasing mineral liberation. The effect of pretreatment using conventional and dielectric heating followed by quenching on the fracture properties of a number single and multiphase brittle materials has been investigated. The reduction in the impact fracture energies and particle strengths with and without pretreatment has been measured in precise single-particle experiments using the Ultrafast Load Cell. Variations in the fragmentation pattern caused by different pretreatments were assessed by measurements of the progeny size distributions. The differences in the effect of thermal treatment on single and multiphase materials are discussed based on the experimental results.

Jan 1, 1995

By Tuncel M. Yegulalp, Anuta Belova

This paper expands on the ZECA (Zero Emission Coal Alliance) technology, which is aimed at making coal a sustainable source of clean energy in the near future. The technology proposed immediate capture of carbon dioxide and other pollutants upon generation, thus alleviating their negative effects in the Earth’s atmosphere. ZECA proposes using chemical energy of coal to produce hydrogen; the latter is then used to produce electricity via fuel cells or Hyrogen-Oxygen turbines. In this study, a chemical engineering package, AspenPlus 12.1, is used to simulate the reactor (reformer) in which hydrogen is produced from methane water and lime as part of the zero emission power plant. Thermodynamic conditions, pressure and temperature, are optimized with respect to molar hydrogen production. Under the proposed conditions, molar conversion efficiency, carbon to hydrogen, of 95% is achieved. Further studies are required to model the complete power plant and to optimize it for efficiency.

Jan 1, 2005

By Duane L. Whiting

The National Environmental Policy Act of 1969 (NAPA) provides guidance for federal agencies in making informed decisions. The Act has been used to determine the potential environmental impacts from mining and other natural resource operations, primarily in the Western USA. To accomplish the purpose of the Act, a process for developing environmental documents was established. The documents (EA/EISs) evaluate environmental impacts and are produced by federal agencies through public participation and cooperating agency review. Effective interactions and up front coordination between agencies and industry is required. An abbreviated history of environmental protection in the USA leading to NEPA, the driving regulation, objectives, provisions and limitations of the Act, and select mining related NEPA projects III the Western U.S. are discussed in this paper.

Jan 1, 1998

Federal Regulations require that coal producers conduct a written, in-house investigation with every lost time injury accident. Besides their obvious value in accident prevention, competently conducted investigations can provide a number of additional benefits to include positive supervisor involvement, the control of rising worker's compensation costs and a measure of protection from civil/criminal proceedings. The paper describes such topics as MSHA minimum requirements, investigator selection and training, accident site procedures, witness interview techniques and the management review process. The reader is also presented with a number of information resources available through MSHA, the National Safety Council and other sources.

Jan 1, 1995

By John O. Marsden

"This article is an attempt to capture a presentation given at the 2016 SME Mineral & Metallurgical Processing Division (MPD) Luncheon held on Feb. 24, 2016, in Phoenix, AZ. It was presented as a tongue-in-cheek, lighthearted view of several of the issues facing our industry, while identifying some of the challenges and opportunities available to new engineers entering the industry today.Disclaimer• What you are about to read includes personal preferences, biases and occasionally arbitrary opinions.• Some readers may have dissimilar opinions on the contents and/or the rank order of the lists.There are eight top ten lists offered in this article: (1) Industry realities (2) Things a metallurgical or mineral process engineering graduate should do (3) Books every metallurgist should have on their shelf (4) Things I wish I had known (5) Legends of metallurgy (posthumous, with highlights) (6) Things we’ve forgotten (7) Mineral processing innovations of the past 20 years and, finally, (8) The future? For some items, additional context or clarification is provided after the item, while for other items no further explanation is warranted and none is offered. Top 10 industry realities1. Metal price cycles.2. Bigger is better (except when it isn’t).3. Ore grades declining across the board of metals/commodities.4. Ores becoming more complex.5. Three-fold increase in capital costs between 2004 and 2015.6. Three-fold increase in operating costs between 2004 and 2015.7. Less capital availability/challenging financial markets.8. Environmental constraints increasing.9. Socio-political constraints increasing.10. The mine manager is always impossible to work with.As Table 1 shows, there was more than a three-fold increase in gold operating costs between 2004 and 2014. The increases for copper, iron ore and other commodities were similar."

Aug 1, 2016

By Gregg W. Davidson, J. Andrew McGlenn, Frank Huber

The Second Narrows Water Supply Tunnel will ensure system reliability in the event of a major earthquake and increase the Greater Vancouver Water District’s capacity to meet the long-term needs of a growing population. The tunnel will be 1,100 m long and 6.5 m in diameter (3,610 LF × 21.3 ft), constructed under Burrard Inlet between North Vancouver and Burnaby in British Columbia. It will be excavated through mixed ground conditions under high groundwater pressure, using a slurry TBM, between a 72 m (236 ft) deep shaft in soil and a 110 m (361 ft) deep shaft in rock. The completed tunnel will accommodate three large-diameter water mains that will be installed as part of the tunnel contract. This paper presents the project from design and contractor procurement, into the current construction stage describing some of the unique challenges encountered during the project development to date.

Jun 13, 2021

By Kristin K. Mueller, Lucie Coudert, Thi Yen Chau Nguyen, Lan Huong Tran, Jean‑François Blais, Guy Mercier

Fluorite (calcium fluoride—CaF2), also known as fluorspar, is an industrial mineral used in metallurgy, hydrofluoric acid production, and ceramics manufacturing. Based on the results from a previous study, a low-grade fluorspar by-product (20.0% CaF2) originating from the exploitation of a rare earth carbonatite deposit can be improved to 75.4% by combining magnetic separation and acid leaching. The present research aimed to develop and optimize a column flotation process to increase the purity of this fluorspar by-product by removing residual silicate minerals and meeting the requirements for ceramic manufacturing (> 85% CaF2). The optimal flotation conditions required for maximizing the recovery and improving the grade of a fluorspar by-product were identified using a conventional approach combined with a response surface methodology (Box-Behnken design). Optimal fluorspar flotation was achieved under the following conditions: 3.6 g/kg of sodium oleate as the collector, 2 g/kg of sodium silicate as the pH modifier and depressant, a conditioning time of 35 min, a flotation time of 7 min, and a solid-to-liquid ratio (S/L) of the pulp of 5%. Under these conditions, 86.8% fluorspar recovery was achieved, and the grade increased from 76.5% in the feed (metallurgical grade) to 88.6% (ceramic grade) in the final concentrate. The silicon content decreased from 5.66% in the feed to 1.12% in the fluorspar concentrate. Using magnetic separation before the flotation improves the final content of fluorspar in the concentrate with the final grade of 94.4%.

Sep 9, 2022

By K. Perry, B. Lusk, Q. Huang, R. Honaker

"Rock dust is applied in underground coal mines to prevent the propagation of coal dust explosions. The application is conducted either dry or wet. Both methods have advantages and disadvantages however the formation of caked rock dust particles is cited as a significant concern for wet applications. A study was conducted to evaluate the effect of modifying the rock dust particle surfaces to repel water and each other by the addition of oleic acid (OA) and sodium oleate (NaOL). At a NaOL dosage of 2 lbs/ton, a contact angle of 112o was measured indicating strong surface hydrophobicity and ability to repel water. FTIR studies indicated a chemisorption mechanism which is necessary for long term stability of the surface modification. The dispersion rate of the modified rock dust samples was elevated by the application of both OA and NaOL thereby indicating a significant reduction or elimination of the detrimental effect of caking. Tests in an explosion chamber showed a 79% reduction in the dust explosion potential relative to untreated rock test applied by the wet technique. INTRODUCTION Mine explosions have been a long-time threat to underground coal miners attracting significant attention to the accumulations of combustible dusts and gasses. In the presence of sufficient oxygen and heat, the accumulations of combustible dust and gass can lead to large-scale underground coal mine explosions [Harris et al., 2010]. To alleviate the problem, rock dust such as limestone can serve both as a thermal inhibitor and a heat sink to inert the coal dust explosibility thereby prohibiting the occurrence of dust explosions [Richmond et al., 1975; Amyotte et al., 1995; Dastidar et al., 1997; Man et al., 2009]. The dispersibility of the rock dust is an important characteristic that determines the degree of explosion prevention [Greenwald et al., 1938; Mozumdar et al., 1974; Amyotte et al., 1995]. Unfortunately, the environmental conditions of an underground mine has the potential to cause caking of the rock dust which reduces the dispersive characteristics needed. The dispersive property of rock dust can be enhanced by modification of the particle surface properties by the application of chemical additives [Greenwald et al., 1938; Mozumdar et al., 1974; Spence, 2004; Vogt, 2011; Doidge et al. 2014]. The major mechanism for rock dust caking is the adsorption of water which forms liquid bridges at the particle-particle contact points where saturated solutions of soluble powder ingredients are present. Changes in temperature or relative humidity result in solvent (water) evaporation and the formation of dry bridges [Rumpf, 1958; Specht, 2006]. One method to prevent caking is creating hydrophobic rock dust to repel water from the solid surface thereby preventing the formation of liquid and solid bridges."

Jan 1, 2015

By Anup Tiwari, Khanindra Pathak, BIBHUTI BHUSAN MANDAL

Failure of in-pit overburden dumps in open-pit coal mines causes debris to flow toward the active working face, threatening the safety of people and equipment. The evaluation of the potential mobility of failing mass will aid in hazard mitigation associated with unwarranted dump failure. The potential mobility is shown by mobility ratio (ratio of total drop between debris flow's initial and final deposition points to total travel distance) and runout characteristics. In light of above, a laboratoryscale debris flow flume was developed to investigate the effect of material gradation and slope angle on runout characteristics and mobility ratio. The total mass of experimental debris mix (Q) is fixed at 30 kg with 20% water content. Experiments at three different slope angles (30°, 35°, and 40°) demonstrate that increasing the proportion of fines in the experimental mix increases runout characteristics while decreasing the mobility ratio. The length and area of the runout decrease as the slope angle increases, while the mobility ratio increases. There is a positive correlation between d50 and runout characteristics at a fines content of 0.1Q, but a negative correlation at a fines content of 0.2Q and 0.3Q. Conversely, there is a negative correlation between d50 and mobility ratio for fines content of 0.1Q, but a positive correlation exists for fines content of 0.2Q and 0.3Q. A new index called the fine-to-coarse (F/C) ratio is used to identify the critical value of fines and coarse proportion that causes a transition from dry granular flow to fluidized debris flow.

May 29, 2023

By S. J. Schatzel, J. D. Addis, V. Gangrade, L. L. Chasko, C. A. Hollerich

A ventilation study using tracer gas was conducted at a western US coal mine. The objective of the study was to evaluate the movement of longwall face air exchanges between the face and worked-out area and to document the presence or absence of face airflow pathways between these locations. The mine operator uses a bleederless longwall ventilation system with a back return and a blowing mine ventilation system. The study was conducted on an active panel and included both underground and surface monitoring sites. The study used sulfur hexafluoride (SF6) released as a slug on the longwall face and in the front of the gob inby the face. The velocity of the tracer gas movement in the gob was 0.019 m/s (3.7 fpm). The rate of movement for the overall tracer gas slug averaged about 0.0091 m/s (1.8 fpm). A separate tracer gas test initiated with the release of SF6 into the legs of the first shield showed the existence of more than one pathway of face air in the general direction from the headgate towards the tailgate corner. Maintaining adequate ventilation air on longwall faces is important for worker safety and for the dilution of methane emitted from the face and caved gob. A more detailed characterization of longwall system air and gas movement allows a mine to better assess its ventilation design for controlling gas on the face and in the gob.

By W. J. Dolinar

The U.S. Bureau of Mines implemented the Fe2+ /Fe3+-SO2 anode reaction in a Cu electrowinning cell with full-size electrodes. Electrowinning was conducted using industrial electrolyte at 258 A/m2 (24 A/ft2) and 40 'C. Manifold injection of electrolyte provided circulation between the electrodes. Five-day operation using an optimized manifold gave an average cell voltage of 0.94 V at 89% current efficiency, which amounted to an energy savings of 2.82 MJ/kg (0.355 kW-hr/lb) compared to conventional electrowinning. Acid misting was completely eliminated, and SO2 concentration 23 cm (9 in.) above the cell averaged 0.06 ppm.

Jan 1, 1995

By J. W. Walkiewicz

The U.S. Bureau of Mines has conducted studies using microwave energy to stress-crack iron ores. In a microwave chamber which simulates a continuous throughput operation, the Bond grindability of a taconite sample was improved by 13 pct at a bulk temperature of 197? C. To further improve the economics of microwave fracturing, higher powers up to 16 kW were used to rapidly heat samples to relatively low temperatures in a continuous belt-fed applicator. A significant enhancement of grindability was obtained with a minus 1.9-cm taconite rod mill feed. At a sample temperature of 130? C, the grindability was improved a maximum of 26.1 pct over the non-microwaved sample.

Jan 1, 1993

By Milka Madahana, John Ekoru

For efficient management of operations, mining companies are required to be able to predict potential scenarios for main market factors. Competitive advantage and value creation are established through managing the value chain well. The mining value chain is usually faced with challenges from various shifts in commodity markets as well as ongoing uncertainties. Therefore, there is a need for accurate analysis of data from the markets, for the prediction of commodities, for instance, Precious Group Metals (PGM). The main objective of this research work is to apply machine learning methodologies with the aim to identify patterns and trends in the Precious Group Metals, and thereafter analyze and predict the future trends of these markets. Numerous machine learning models are applied to a dataset consisting of 15 years of daily price for eight precious metals namely Platinum, Palladium, Rhodium, Ruthenium, Osmium, Indium, Silver, and Gold. The results reveal the patterns and trends within the data sets and that different machine learning methods could be suited for the prediction of market prices for each of the PGMs. The application of an amalgamation of various machine learning methods may result in more accurate predictions of the PGM markets. Accurate prediction of market prices for PGMs will possibly result in unlocking untapped sources of value in the mining industry.

Jun 25, 2023

By D. K. Dysinger

The U.S. Bureau of Mines investigated leaching of chalcopyrite with sulfuric acid-oxygen under conditions anticipated during in situ leaching. A central composite experimental design was chosen to study oxygen pressures of 150, 300, and 450 psi, leach temperatures of 35?, 65°, and 95° C, oxygen-to-chalcopyrite mass ratios of 0.5, 1.0, and 1.5, leach times of 8, 16, and 24 hours, initial acid strengths of 0.6, 1.2, and 1.8 g H2SO4/g chalcopyrite and pyrite to chalcopyrite mass ratios of 0, 1, and 2. The leaching kinetics were consistent with the shrinking core model. A quadratic response surface model was used to determine linear and interaction effects of the design factors on rate constants from Arrhenius correlations.

Jan 1, 1993

By L. M. Sandoval, R. Kaunda, C. N. Vasquez, S. C. Falcon

Artisanal and small-scale mining (ASM) involves a wide range of practices, from highly informal and minimally mechanized mining operations with predominantly manual work to formal practices carried out by small but high-tech industrial mining operations [1]. ASM may be a traditional practice, with skills passed from one generation to another. It can be an important driver of local economic development, while simultaneously contributing to a complex array of positive and negative socioeconomic and environmental impacts. There are more than 100 million artisanal and small-scale miners in 80 countries worldwide, and they supply around 20% of the worldwide gold production [2]. According to the Peruvian Ministry of Energy and Mining (MINEM), in 2020, 32% of fatal accidents in formal (legal) Peruvian mining operations were caused by groundfall events [3].The lack of resources, knowledge of best practices in health and safety, and insufficient equipment used in ASM make the probability of suffering work accidents very high. Furthermore, groundfall is one of the main causes of accidents and injuries in underground mines around the world [4], and it is also a concerning problem in ASM, where the associated fatality rate is similarly high. Unfortunately, a proper record of accidents in ASM is not kept, so an estimate of the actual number of groundfall accidents cannot be accurately developed [5]. Currently miners rely on empirical and observational tools acquired through previous experience to assess groundfall risks. The risks for artisanal miners can tend to be significantly greater than risks for those from the mining industry. This is due to the lack of regulation of ASM, which tends to operate outside the legal framework and the regulations lack of enforcement in force for occupational health and safety regulations.

Mar 2, 2022

By Edmond F. Lawrence

The Calico area lies within the Walker Lane fault zone, six miles north of Schurz, Nevada. The mineralized area is overlain by a thick section of Tertiary tuffs and ash-flows, that have been intruded by a series of andesite plug, dikes, and sills. The pre-Tertiary rocks outcrops only in two areas at one to two miles distance from the drilling areas. Underlying the volcanics are sediments ranging from siltstones, sandstone, calcareous shales, to carbonates of the Luning sequence. These have been intruded by one or more phaneritic intrusives ranging in composition from quartz diorite to quartz monzonite, with the development of a skarn zone on the south flank that contains extensive mineralization consisting of magnetite, pyrrhotite, pyrite, and chalcopytite, with traces of sphalerite, galena, and molybdenite. The magnetite, pyrrhotite, and part of the pyrite appears to be contemporaneous with the skarn, while, part of the chalcopyrite, galena, sphalerite, molybdenite, quartz, and calcite, occurs as minute veinlets cutting the other minerals. This later mineralization may be associated with a late stage of the same sequence, or possibly associated with another intrusive to the southwest. Geophysical work has consisted of aerial magnetics, ground magnetics, gravity, seismic, and induced polarization surveys. Preliminary induced polarization surveys indicated anomalies at depth, both over the magnetic anomaly and to the northwest. Subsequent IP work confirmed this earlier anomaly, and drilling disclosed extensive mineralization at depths of 400 feet on the northwest end and over 1,000 feet to the southeast.

Jan 1, 1967

By G. W. Mannard

The large massive sulphide deposits present a formidable challenge to the economic geologist. They represent such huge concentrations of iron, sulphur, base metals and precious metals that it is difficult to conceive how they were derived from the crust or mantle of the Earth. The problem of the origin of massive sulphide deposits has generated a geological controversy which has lasted two hundred years and shows no sign of abating. The economic incentive to solve this problem is great, as the massive sulphide bodies are the moat important source of the world's zinc, lead, and silver, as well as yielding large amounts of copper and gold. Using the criteria of abundance, size, age distribution and gross value of contained metals, the predominant sub-group of the massive sulphide deposits is that which comprises the crudely conformable pyritic (or pyrrhotitic) deposits which occur in stratified volcanic and sedimentary rocks or their metamorphosed equivalents. Examples of this sub-group are: the Buchans, Bathurst, Noranda, Kidd Creek, Flin Plon and Sullivan deposits of Canada; the Mt. Isa and Broken Hill orebodies of Australia; the Cyprus, Rio Tinto, Meggen and Rammelsberg deposits of Europe; Ducktown and the United Verde in United States; and the Kuroko deposits of Japan.

Jan 1, 1973

By Robert W. Yokom

As the search for new sources of energy and minerals leads to more remote areas of the country - and the world - the need to plan for adequate housing and community facilities for the construction and operations workforces and their families takes on an importance equal to the mining and processing facilities themselves. A corollary to the need for planning is the increasingly crucial need for development companies to devise effective strategies for dealing with the local communities impacted by these projects. Experience has amply demonstrated the high price to be paid for failure to learn this lesson, a price measured in lost productivity, confrontation with local communities, labor turnover, mental health and other social and eocnomic problems. In Sweetwater, Wyoming, a new industrial activity caused the population to double from 18,000 to 36,000 between 1970 and 1974. During that period industrial productivity fell 25 to 40 percent, cost overruns on the principal new industrial facility exceeded 33 percent, annual employee turnover rates climbed above 100 percent, the local mental health clinic workload increased nine times and complaints to the local law enforcement agency increased 60 percent.

Jan 1, 1981

By Thomas Schwind, Benedikt Grau, Angelos Gakis

"In Crossrail’s Farringdon station, compensation grouting was successfully utilized to mitigate the surface settlements induced by the tunneling works. The main focus of this study was the platform tunnels, which were approximately 300m long each and were enlarged to platform size using sequential excavation method (SEM) from the existing TBM running tunnels, initially supported using sprayed concrete linings. The rear grouting injections were carried out at a typical distance of minimum 5m above the completed, fully strengthened shotcrete lining hence inducing some additional stresses. In-tunnel monitoring using surveying targets was performed systematically to ensure that no excessive distortion of the initial shotcrete lining occurred. 3D finite element analyses were utilized to back calculate the actual “effective” pressure that was imposed on the completed shotcrete rings against the additional measured in-tunnel displacements due to the compensation grouting episodes. Additionally an assessment of the theoretical, “maximum” allowable grouting pressures that would lead to overstressing of the lining is presented. INTRODUCTION As part of the back analysis performed for the SEM tunnels in Farringdon station, an investigation of the effect of compensation grouting on the two constructed platform tunnels was undertaken. The platform tunnels were 10.6m high by 11.4m wide and approximately 300m long each. They were enlarged to their final shape from the existing TBM tunnels using SCL methods. This study utilized 2D and 3D finite element (FE) analyses in order to back calculate the observed tunnel crown displacement, assessing the equivalent grouting pressures during the rear injection episodes of the concurrent grouting operations. The results provide a useful reference for the order of magnitude of the grouting pressure load cases that can be applied in the numerical simulation of similar cases. Part of the results presented in this paper, were derived by the second author as part of his Master of Science thesis in Technical University of Graz."

Jan 1, 2016