Search Documents

By C. J. Bise

In August, 1977, the Federal Surface Mining Control and Reclamation Act was signed into law [I]. It stated that: "The Congress finds and declares that because of the diversity in terrain ... and other physical conditions in areas subject to min ing operations, the primary governmental res- ponsibility for developing, authorizing, issuing, and enforcing regulations for-surface mining and reclamation operations subject to the Act should rest with the States." Section 516 of Title V (Control of the Environ mental Impacts of Surface Coal Mining) of the Act deals with the surface effects of underground coal mining operations. "Each permit issued under any approved State or Federal program pursuant to this Act and relating to underground coal mining shall re quire tfieoperator to adopt izeasures consist ent with known technology in order to prevent subsidence, causing material damage, to the extent technologically and economically feasible, maximize mine stability, and main tain the value and reasonable foreseeable use of such surface lands, except in those instances vhere the mining technology used requires planned subsidence in a predictable and controlled manner: Provided, that nothing in this subsection shall be construed to prohibit the standard method of room and pillar mining. "

Jan 1, 1980

By W. E. Lytle

Environmental permitting is a critical component for joint-venture projects located in the Commonwealth of Independent States (CIS). This paper presents the basic CIS regulatory environmental requirements for permitting of a hypothetical mining source and emphasizes air permitting. Topics which will be covered include: the Expertiza process, air pollution quantification, data requirements, and air pollution modeling protocol. A comparison will be made between permitting requirements for air pollution sources in the United States and a CIS country, Kazakstan.

Jan 1, 1998

By Jeremy Cawley, Horry Parker Jr., Clint Wilson

The 5180 m EPBM drive on the Lower Olentangy Tunnel (LOT) is predominantly within glacial overburden. To connect LOT with the existing OARS deep tunnel in limestone bedrock, the upper 15 m inside diameter Vine Street retrieval shaft telescopes down to 6.7 m in diameter and extends into the karstic Columbus Limestone to a depth of 51 m, where a 104 m SEM tunnel will connect to OARS shaft 6. Pre-excavation grouting was reuired prior to lower shaft excavation to reduce potentially high groundwater inows. This paper discusses the secant pile installation, grouting program, shaft excavation, and hydrogeologic observations.

Jun 23, 2024

By William R. Yernberg

The Society of Economic Geologists (SEG) held its biennial conference May 14 through 16, 2006, in Keystone, CO. SEG is an international organization with about 3,500 individual members with interests in economic geology. The 2006 SEG conference theme was “Wealth creation in the minerals industry — integrating science, business and education.” The conference exceeded expectations with 705 participants, including 102 students, from 44 countries. The conference featured 30 oral presentations, 24 professional posters and more than 70 student posters. The conference also included a trade show with 50 vendors, numerous field trips, workshops and social activities.

Jan 1, 2006

By David A. Campbell

There has been a long history of ironmaking on the North East coast of England centered around the River Tees. The industry developed here because of the availability of good coking coals to the North in Co. Durham, and the discovery in 1851 of ironstone in the nearby Cleveland Hills, South of the .River. Cleveland ironstone is relatively poor in quality, with an iron content not exceeding h% and high proportion of sulphur and phosphorous. The iron exists in chemical association with alumina and silica, and physical beneficiation processes involve a serious loss in iron unless the upgrading is limited, when the economics of the process become doubtful. Over the years, richer foreign ores have replaced the local ironstone, and the last operating mine was closed in 1964.

Jan 1, 1982

By Lawrence Adler

The properties of a geologic mass may be considered from a resource or an engineering viewpoint. The primary engineering applications include ground control, excavation, bulk handling, and hydrology. This study will focus upon these areas in descending order. For an adequate geologic description, data is necessary on the following components: (1) the intact rock, (2) geologic structures, (3) contained fluids, and (4) existing pressures and temperatures, see Table 1. This information, combined with the engineering specifications, provides the basis for a formal geotechnical analysis as illustrated in Figure 1. For a structural analysis it is essential to establish the mechanical properties of the material composing the structure. This material, termed the "rock mass," consists mainly of the first two geologic components, the intact rock and geologic structures (Figure 1) Consideration of fluids will be subordinated to their role as chemical agents affecting the mechanical properties. The existence of pressures and temperatures generally lies beyond the scope of this study.

Jan 1, 1973

A charge of the Research Council of the Society for Mining, Metallurgy and Exploration, Inc. (SME) is to ?? identify longer term research ideas/needs, that in the perception of the SME Research Council, could represent significant technology breakthroughs ?? (SME, n.d.). In 2008, the Council decided that instead of unilaterally developing a list of top priorities, it would involve the entire membership of SME in identifying the top priorities. Additionally, it decided to keep the list short. This paper describes the process and results from that exercise.

Jan 1, 2010

By K. Koizumf, A. A. Cram, K. Whitchurch

The Expert Scheduling is a new, exciting method for scheduling underground and open-cut coal mines. A key feature of the Expert Scheduler is the adoption of an expert or artificial intelligence system. The expert system makes decisions regarding the schedule, such as which area should be mined. With existing scheduling systems these choices are made by the scheduling engineer. Developing one area may be better than another if it offers better quality or lower costs. Information the engineer considers in these decisions could be; • coal tonnage and quality targets, • equipment utilisation, • mining cost, • and other practical constraints. In expert scheduling a number of experts are appointed to make these decisions. A number of mining strategies are examined for each period. Information for each strategy is evaluated by "experts" and the "best" solution adopted. The method is based on the Blackboard Techniques. With this technique information is presented to "knowledge sources” or "experts" by the Blackboard Controller for their "opinions". These "opinions" are examined by the Blackboard Controller to select the best strategy. Engineers can readily add experts to the system, and modify the weighting of experts to suit mining conditions. Using an Expert Scheduler means that many schedule op- tions can be analysed quickly with full repeatability.

Jan 1, 1996

Mining is big business in Ontario. The province is Canada?s leading mining region. It consistently ranks among the top 10 jurisdictions worldwide for exploration spending, reaching about C$1 billion in 2011. More than 26 percent of all exploration and appraisal dollars spent in Canada are invested in Ontario. Minerals produced include nickel, copper, platinum group elements (PGE), cobalt, zinc, diamonds, gold and silver. It was reported that there are more than 600 mining exploration projects in the province. And, recent discoveries of chromite in northern Ontario?s Ring of Fire will add to the province?s mineral production in the coming years.

Jan 1, 2013

By Rick Frechette, Bryan Ulrich

Representatives from several mining operations in three western states left their mines behind for a day in February to discuss with their peers the issue of water. The event was Knight Piésold and Co.’s Roundtable 2007, held in Elko, NV. It was third such event put on by the company. The issue this year was site-wide water considerations.

Jan 1, 2007

By J. J. Gusek

The Riley Pass strip mine is an abandoned uranium-bearing lignite deposit in Harding County, South Dakota, covering about 150 acres of highwalls, pit floor and mine spoils exhibiting elevated levels of radioactivity. Six reclamation design alternatives were developed, ranging from doing nothing to reclaiming to approximate original con-tour. The alternatives were evaluated for expense, site stabilization, and mitigation of public safety hazards. A comparative economic evaluation on three of the alternatives was completed for the Forest Service in selecting an alternative and substantiating federal funding requests. This evaluation included economic impacts associated with physical and radiologic health hazards, affects on recreational users, socioeconomic impacts and environmental improvement.

Jan 1, 1995

By George S. Austin

Adobe, dried mud bricks, have been used since before historic time in the construction of dwellings. Building materials are normally evaluated for thermal performance based on measurements known as R- and U-values. The R-value is an indicator of the ability of a wall to insulate effectively and the higher the R-value, the better it is as an insulating material. The U-value, or value of conductance, is the reciprocal of the R-value and reflects the rate at which heat is conducted through a material. But the "heat capacity of the wall" must also be considered. This measures the length of time that passes before a steady state of heat flow is achieved. The effective U-value measures both the resistance to the transfer of heat and the capacity to hold heat. These latter value make adobe a far more interesting as a modern building material that was formerly recognized.

Jan 1, 1983

By Dale W. Norris

United States Steel's Cumberland Coal Operations is located in Greene County in the southwest corner of Pennsylvania. The mine and related facilities have been in operation since September of 1977. Production from this mine, U. S. Steel's first commercial coal mining venture, will eventually reach a level of 2.72 million mt of clean coal per year and is totally committed to electric power generation. Cumberland is a slope mine in the Pittsburgh seam and is mined by continuous mining machines and longwall. The coal from the mine is trans- ported by belt to the surface, taken through a rotary breaker for initial preparation, and stored in raw coal silos. It is then processed through the preparation plant and taken to a clean coal silo where it is held for train loading. Cumberland Mine operates its am 28.16 km railroad to transport the coal to the Monongahela River. The unit train consists of thirty-one 90 mt cars. The coal, once loaded on barges, is then shipped to the customer. Cumberland Mine is one of the most modern coal preparation and unit train loading systems in the nation. The preparation plant is de- signed to receive coal from the silos at a rate of 720 at per hour. The +6.35 mm material is screened out and cleaned in a Daniels heavy media vessel with two 3.35 m weirs. Minus 6.35 mm material is fed to sixteen #88 Deister concentrating tables. The cleaned coal from this circuit is dewatered, and all effluents from the mechanical dewatering report to the classifying Cyclone sump for classification through ten 35.6 cm cyclones. The cyclones overflow material (-150 mesh) is processed through two banks of three 8.5 m3 Denver D.R. flotation machines. The cyclone underflow pro- duct (28-1 0 mesh) is processed in two banks of 5 six 2.83 m Denver Sub A machines. The clean flotation product is then dewatered in Bird screen bowl centrifuges, blended with the other clean coal size fractions, and the total plant product further dewatered in a thermal dryer.

Jan 1, 1980

By George E. Summers

A salt dome appears to provide the basic medium requirements for the excavation of the 315 foot diameter, unsupported spherical cavity at a depth of 2700 feet required by the AEC in a proposed "decoupling" experiment. Tatum Salt Dome was a natural choice for a site because more geological and hydrological information has been accumulated on Tatum than any other salt dome on the Gulf Coast. The Tatum Dome is a mile in diameter, roughly flat topped, nearly cylindrical in shape and has some overhang at the top. The salt stock has nearly vertical layering of alternating bands of salt and anhydrite. In the vicinity of the dome, adequate fresh water for solution mining is available in surface streams and in subsurface aquifers. A saline aquifer is available for brine disposal. A tentative cavity location was selected near the center of the dome which meets the design criteria established by the AEC.

Jan 1, 1968

By R. G. Reddy

Spent potliner is generated in the electrolytic process of reducing alumina to make aluminum metal using molten fluoride electrolytes. Spent potliner (SPL), obtained at the end of the pots life contains a small amount of cyanide and fluoride which present environmental problems. SPL became a listed hazardous waste under RCRA (K088) in July, 1990. One of the possible uses of spent potliner is as a substitute for Calcium Fluoride (CaF2) as a fluidizer in iron-and steel making and in the glass industry. A low viscosity and a low melting point are prime requirements for accomplishing the above. In the present study, viscosity measurements were performed. Effect of various additives, such as sand, limestone, dicalcium silicate dust, and MgO baghouse dust on the viscosity of SPL was studied. The results showed that with the addition of sand and limestone, very high fluidity of SPL melt can be obtained at significantly low temperatures. The results suggest that spent potliner mixed with additives could potentially be used as a substitute fluidizer.

Jan 1, 1999

By L. Gertsch, R. Gustafson, J. Rostami, C. Swope

Development of a permanent human base on the moon for exploration requires a self-sustaining system. Such a system entails the production and processing of limited amounts of raw material on the moon. Any mining and construction activities on the moon can only be performed by a robust excavation machine that can excavate a variety of material, from loose surface regolith to consolidated (frozen) regolith with embedded rocks in the mixture. Meanwhile, a limited amount of information on lunar regolith is available to develop and optimize a machine for lunar ground conditions. Therefore, any excavator designed for use on the lunar surface should have the ability to adapt to a wide range of operating conditions. A prototype cutterhead for the lunar excavator was built and tested at the Kennametal facility in Latrobe, PA. This paper discusses the results of initial material characterization, as well as full-scale tests of a prototype cutterhead in relevant material. A brief review of anticipated production rates under various assumed ground conditions is also presented.

Jan 1, 2010

By Rick A. Croote

The objective of the Cerrejon Coal Project is to mine and export a minimum of 15 million metric tons per year of bituminous coal from the Guajira Pennisula in Colombia, South America. Major components of the project will include an open pit mine, 150 km railroad, marine terminal for storage and shipping, and accommodations for the support personnel. This paper primarily reviews the coal handling facilities at the mine and port which will include crushers, conveyors, silos, stacker/reclaimers, and a shiploader. Of special interest is the design concept for unloading bottom-dump railcars, a programmable controller control system with automatic stacking and reclaiming, a linear-type shiploader, and 2.4m wide conveyors running at 5 m/sec.

Jan 1, 1983

By T. Bartnitzki, N. Fietz

"INTRODUCTION For a long time now automation has been state of the art in production engineering and chemical engineering. The advantages of automation are, for instance, higher reliabilities of production processes, higher product qualities as well as capacities and improved safety conditions for the personnel. In contrast, many operations in mining are still conducted manually by machine operators instead of autonomous control units. One example for this is the excavation of underground hard coal which is still executed with aid of human perception. The Institute for Mining and Metallurgical Machinery (IMR) has been working on possibilities for sensor-based automation of mining machinery for many years now. Thereto the focus is set on the implementation of common material analysis techniques into ruggedized conditions as a basis for automation. Laser-induced breakdown spectroscopy (LIBS) for instance is an atom emission technique which enables the determination of the elemental composition of a sample. After introducing LIBS this paper will give an overview on dust formation during the cutting process. With the illustration of a few examples the challenges in determining dust concentrations specifically such of cutting processes are explained in further detail. The final chapter will outlay the possibilities and challenges in utilizing cutting-induced dust for the automation of shearer loaders. LASER-INDUCED BREAKDOWN SPECTROSCOPY LIBS Fundamentals LIBS (laser-induced breakdown spectroscopy) is a contact-free method for analyzing materials in any state of aggregate. It pertains the atom emission techniques and is based on the generation of plasma, inducing avalanche ionization on the surface of a solid material or any spot in a gas or aqueous solution. With sufficient background information on the expected elements and an additional calibration, this method can determine all present elements not only qualitatively but also quantitatively. However, this method cannot be utilized for determining the molecular composition of materials – if this feature is required a complementary method such as Raman analysis needs to be added. (1, 2)"

Jan 1, 2015

By Edward C. Dowling

Froth flotation has been used industrially for many years to separate valuable minerals from their associated gangue constituents. Notwithstanding the significance of this process to the mineral industry, many of the engineering tools needed for the evaluation of the flotation process are still in a developmental stage. Traditionally, the evaluation of a flotation test on both the laboratory and industrial scale has been based largely on a rougher recovery value achieved at a sufficiently long time to give a "final" or "equilibrium" recovery value. The assumption of a time equivalency for a given recovery value between various flotation tests or between laboratory tests and industrial operation underlies this method of evaluation. Such an assumption implies that flotation is an "equilibrium engineering process" and that the time-rate recovery of material from the flotation cell is not affected by changes in the flotation system. It has been shown by Bushell (1) and by Klimpel (2) that the assumption of time equivalency between various flotation tests is unjustified. Consequently, better tools are needed for evaluating flotation test results, Because mathematical flotation models which incorporate both a recovery and a rate function can completely describe flotation time-recovery profiles, they can provide an excellent tool to evaluate flotation tests.

Jan 1, 1984

By O. F. Brown

The use of quality materials (aggregates and asphalt binder) in optimal proportions is the key to producing optimally performing hot mix asphalt (HMA). The Superpave mix design standard in the US introduced specific volumetric and binder property requirements in HMA design. Different methods for HMA constituent proportioning have been proposed in various guidelines. The design process to determine the HMA blend is currently iterative and engineers rely almost exclusively on experience. This approach is time consuming and often does not result in cost-optimal HMA mixtures. This paper introduces a mixed integer linear programming (MILP) optimization model for hot-mix asphalt constituent proportioning. The MILP model minimizes the total mix cost while satisfying all the volumetric, binder and mix property specification requirements. The model has been successfully validated with real-life example. The aggregates and binder ratios from the model were in close agreement with those from the contractor. The Bailey ratios and the gradation constraints were also satisfied. The cost of the optimal mix was $0.804/Mg less than that of the contractors?. This marginal reduction might make all the difference in an industry that is highly competitive. The MILP model also demonstrated that adding RAP to the contractor?s design would reduce the cost of the blend by $5.74/Mg. The virgin binder content was reduced by 1% because of the recycled asphalt contained in the RAP. This work represents the first successful attempt in incorporating both aggregate and asphalt performance requirements into the optimization formulation. Applying these models will ensure the minimum cost mix that meets all constraints and will increase profit margins for plant operators.

Jan 1, 2012