Search Documents

By O. Salami, G. Xu

Fire accident is one of the most classic safety concerns in underground mines both in the USA and abroad. It may occur from pool fires due to leakages in hose or pipes, vehicle fires, or fires in tires and conveyor belts in the underground mines. It may also result from the storage of flammable materials such as gasoline, diesel, and explosives in the underground. When fire occurs in an underground mine, it releases heat, smoke, and other toxic gases such as carbon monoxide, and methane to the surrounding thereby making life unbearable to the miners. Furthermore, smoke greatly impact visibility in the underground which makes evacuation even more onerous and challenging. To this end, a thorough investigation of fire behavior and spread of toxic gases in a practical underground mine is imperative to develop a reliable emergency evacuation plan in an event of fire disaster in the underground mine. The objective of this study is to investigate temperature variation and CO spread along mine airways by conducting full-scale fire experiment in the underground mine. The results presented from this study are crucial to developing evacuation plans in underground mines. In addition, the findings from this study could be used to validate existing evacuation models.

Mar 2, 2022

By R. G. Reddy

Spent potliner is generated in the electrolytic process of reducing alumina to make aluminum metal using molten fluoride electrolytes. Spent potliner (SPL), obtained at the end of the pots life contains a small amount of cyanide and fluoride which present environmental problems. SPL became a listed hazardous waste under RCRA (K088) in July, 1990. One of the possible uses of spent potliner is as a substitute for Calcium Fluoride (CaF2) as a fluidizer in iron-and steel making and in the glass industry. A low viscosity and a low melting point are prime requirements for accomplishing the above. In the present study, viscosity measurements were performed. Effect of various additives, such as sand, limestone, dicalcium silicate dust, and MgO baghouse dust on the viscosity of SPL was studied. The results showed that with the addition of sand and limestone, very high fluidity of SPL melt can be obtained at significantly low temperatures. The results suggest that spent potliner mixed with additives could potentially be used as a substitute fluidizer.

Jan 1, 1999

By VASU GANGRADE, Marcia Harris, Kumar Vaibhav Raj, Jim Addis, Khaled Mohamed, Snigdha Sarkar

The National Institute for Occupational Safety and Health (NIOSH) conducted a ventilation assessment for a recently established underground room-and-pillar stone mine implementing split-mine ventilation. The primary objective was to examine the impact of the length of the in-place stone stoppings on face ventilation efficiency. These stone stoppings serve to separate the intake and exhaust entries and align with the mining direction. To achieve this, computational fluid dynamics (CFD) modeling was utilized. The appropriate turbulence model was selected, and a mesh convergence analysis was conducted for the CFD model. Following that, the CFD model was validated using the conducted ventilation surveys. Two configurations of in-place stone stoppings, designated as Layout-I and Layout-II, were simulated using the validated CFD models. Layout-I featured a shorter in-place stone stopping, while Layout-II had a longer one. The results obtained from the CFD models demonstrated that the increased length of the in-place stone stopping in Layout-II resulted in a notable enhancement in ventilation efficiency at the advanced faces (last stopping), elevating it from 4% in Layout-I to 8.4% in Layout-II. However, no significant impact of the in-place stopping layouts was observed at other faces. In general, Layout-II exhibited a greater circulation of air at the outby stoppings.

Feb 1, 2024

The 2014 George A. Fox Conference at the Graduate Center, City University of New York in New York City was presented under the theme, ?21st Century Challenges for the Tunneling Industry. Bruce Grewcock, chief executive officer and president of Peter Kiewit Sons? Inc., opened the conference with a keynote address in which he set the tone for the rest of the day by touching on the many challenges the industry is facing, which are plentiful and complex. Covering the breadth of the industry, he spoke about everything from the technical challenges that come from working beneath the streets of some of the most densely populated regions in the world to the challenges that come from working with the people who live in those areas. ?My observation is that we, as an industry, are being asked to put structures in places where they are needed, but are complex environments to work in,? said Grewcock. ?We work in an industry that relies on some of the most technically challenging engineering in the world, and when we are done with a project, we cover it up and no one ever sees it.? Despite these issues, Grewcock said that, in his opinion, the biggest challenge the industry is facing is that of people; more precisely, where to find the next batch of people. Looking out at the conference-record crowd of more than 400 registered attendees, Grewcock quipped that he saw plenty of gray beards and asked aloud, ?Where will we find, educate and train the people to tackle the issues that this industry will face in the future??

Mar 1, 2014

By JIACHENG XIE, Juanli Li, Wenyong Du, Tao Cui, Mengyao Dong, Pengfei Huo

The operation of intelligent coal mining in complex geological environment is still unable to realize automation. In order to realize the autonomous cutting of fully mechanized mining equipment and improve coal production, a mining and transportation equipment dynamic advancement path planning method based on spatial kinematics coordinate deduction prediction and real-time correction prediction of coal-rock state identification of equipment cutting current index are proposed. Firstly, the spatial motion law of the mining and transportation equipment is analyzed, and the mathematical model of the spatial motion of the mining and transportation equipment is established. The relationship between the adjustment of the shearer rocker arm and the pose change of the scraper conveyor is determined, and the coordinate deduction model of the spatial advancement position of the equipment is determined, which provides a theoretical basis for the advancement path planning of the mining and transportation equipment. Then, on the basis of the mathematical model construction, combined with real geological data and equipment information, the three-dimensional dynamic planning of the advancement path of the mining and transportation equipment is carried out from the two dimensions of the horizontal advancement direction and the shearer walking direction. At the same time, the relationship between the cutting current index of shearer and the state recognition of coal-rock mass is analyzed, and the coal-rock mass state identification of cutting current and the adjustment of rocker arm model is constructed, and the real-time dynamic correction of three-dimensional path is carried out, so that the planned path can better adapt to the sudden change of real geological environment. Then, using the unity3d virtual reality technology, a simulation system for the horizontal advancement path planning of the virtual mining and transportation equipment is constructed, which simulates the real advancement operation process of the mining and transportation equipment and conducts advancement training. Finally, the dynamic advancement scheme update prediction based on the existing actual cutting but ahead of the actual cutting is realized in the virtual scene, and the optimal scheme is transmitted into the existing prediction cutting system to guide the actual physical equipment mining. The path planning method can control the coordinate position error of the advancing cutting path within 15 mm, which provides ideas for the research on the advancing path planning of fully mechanized equipment.

Nov 22, 2022

By A. F. Barsotti

Apart from jewelry, holistic apparel, and special collections of color and sometimes rare crystal specimens, the average layperson has little or no appreciation of the omnipresence of minerals or mineral derived products in the home. From concrete in the driveway to aspirins in the medicine cabinet, minerals, especially industrial minerals, play a major role in day to day living. For a better appreciation of this let's look into the a day of the life of a fellow named John, and see how much we depend on industrial minerals. The sounds of soft violins nudged John from his sleep. The melodic sounds of Beethoven's Pastoral coming from his radio alarm clock brought him out of his dreams. He reached for the reading light switch, then checked his watch--6:30 a.m., and another day of work. As he got up, the darkness outside reminding him of winter coincided with the soft voice of the all night disk jockey forecasting the fall of four inches of snow. Warm beads of water beating on his face removed all remnants of sleep and, like a stimulant, the morning shower brought thoughts of yesterday and plans for a new day. These carried over as he looked himself in the mirror while shaving and brushing his teeth.

Jan 1, 1993

By V. K. Reddy Kallam, NEHA PANDEY, Sunil Kumar Tripathy, ARIJIT BISWAS

The study investigates SO2 leaching of low-grade ferruginous manganese ores to selectively recover manganese as MnSO4 and produce battery-grade electrolytic manganese dioxide (EMD). The effects of leaching parameters (duration, temperature, SO2 flow rate) on Mn recovery were studied. Under optimum conditions, 97.9% Mn recovery was achieved. The MnSO4 leach liquor was purified and used for electrowinning EMD with 88.01% purity and battery-active γ structure.

Apr 20, 2022

By L. G. Wilson

In our comparison of California and Turkish colemanites, we should first place the discussion in context. In order to exclude technical considerations, which are not germane to this paper, we must make the manifest and basic observation that if colemanite were not acceptable for the production of glass products it would not be used, and we would not be interested in this comparison at all. Suffice it to say that the colemanites, being calcium borates, provide a necessary flux in glass manu¬facture, together with the requisite degree of physical strength and chemical durability which can be achieved only by the use in glass of a. flux substanti¬ally free from alkali; so the sodium borates are automatically excluded from the production of textile fibers. Thus we have today under consideration only California colemanite, Turkish cole mite, and, because it provides a degree of competition to both, ABA, or anhy¬drous boric acid, which, although it is a refined intermediate and of much higher cost, it is also of a much higher degree of purity, and its characteristics can easily be modified to produce a desired end product, so we must include it in any consideration of high quality borates. [Calcim Borate Pentahydrate] Colemanite is a [calcium pentahydrate,] with the formula Ca2B6011.5H20. It has a theoretical B203 content of 50.8%.

Jan 1, 1973

By Ahmet Unal

Use of radio frequency identification (RFID) technology to solve informational needs in isolated and restricted underground mining environments will be reviewed, giving specifications of some past and currently available systems. The advantages and disadvantages of using various frequencies, system configurations, and specific components, including their construction standards and capability, will be discussed. The remaining challenges to more widespread use of RFID systems for personnel and vehicle tracking will be identified, and recommendations concerning operating environment capabilities will be detailed. Finally, the ultimate requirements for maintaining system integrity during and following a coal mine emergency will be discussed.

Jan 1, 1997

By Roger Bell

Most modern mines can profit from improvements in information handling. Recording systems in many cases were designed to satisfy certain necessary legal requirements, but not specifically to provide management information. As a consequence, the top managements of these properties work with cost data and production information that is dated, lacking in detail and clouded with supposition. It is the intent of this paper to describe an information system for a mine-plant complex in terms of the type of data, application areas and the existing equipment technology that may be applied to improve this situation. The economics of information processing and data handling will not be discussed in detail. This paper is based on the premise that information is something of value and that information processing like a manufacturing operation works for and is subject to management control. Information, the product, must be of quality, and the cost must be favorable in terms of its use.

Jan 1, 1965

By K. Rüter

Sustainable investment is a global growth market. Companies that can reconcile economic, environmental and social objectives not only minimise risks, but also realise significant potentials of added value. This particularly applies to the metals & mining industry, as it is an attractive sector for investors and, at the same time, faces major challenges in the field of sustainable development. oekom research AG is an independent rating agency specialised in the analysis and evaluation of the environmental and social performance of companies, sectors and countries for institutional investors and financial service providers in the socially responsible investment (SRI) sector. oekom research has been active in the sustainable investment field since 1993 and its research is currently being used by managers of more than 60 bond and share funds with a volume of assets totalling more than 4.5 billion Euro. The company?s research and its central instrument, the Corporate Responsibility Rating (CRR), are based on the world's most comprehensive set of criteria for the ethical assessment of companies. With the support of an independent scientific advisory board, these universal and industry-specific sustainability criteria are being constantly updated reflecting the dynamics of global challenges in sustainable development. Increasingly, the rating results and benchmark reports of oekom research are also being recognised by the companies as a valuable tool to identify best practices, areas for improvement, and potential risks. This paper will outline the methodology of oekom research, the identification of key sustainability issues in the metals & mining industry, the development of industry-specific sustainability criteria (indicators) for the assessment of the metals & mining industry and key findings of the recently completed CRR of twenty major metals & mining companies.

Jan 1, 2007

By Ray E. Harris

A resource of 134,400,000,000 tons of minable trona and mixed trona and halite underlies an area of about 1,300 square miles vest of Green River, Wyoming (Culbertson, in preparation)(Figure 1). In 1982, the total domestic consumption of soda ash (refined trona) was 6,667,000 short tons (Kostick, 1983), approximately 90 percent of which came from Wyoming trona. This enormous resource occurs in the Wilkins Peak Member of the Creen River Formation (Eocene). The Green River Formation is derived from sediments deposited in a large lake (Lake Gosiute) that occupied the Green River Basin in south-western Wyoming 38-54 million years ago. The Wilkins Peak Member represents a restricted, evaporite-rich cycle of deposition during which time the trona deposits were formed. A total of 42 trona beds are known, of which 25 are of sufficient thickness and extent to be considered minable (Culbertson, in preparation).

Jan 1, 1984

By M. L. Harris

Explosions in underground mines and surface facilities such as processing plants are caused by confined accumulations of combustible dust and/or flammable gas mixed with air in the presence of an ignition source. Underground explosions can be prevented by minimizing methane concentrations through methane drainage and ventilation, by adding sufficient rock dust to inert the coal dust, and by eliminating ignition sources. The effectiveness of rock dust in arresting explosion propagation was proven by experiment and practice (1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11). The precise mechanism by which rock dust (generally pulverized limestone dust) quenches flame has not been fully explained, but is believed to be absorption of thermal energy from the heated gases and absorption of radiant energy, which reduces the preheating of unburned coal particles ahead of the flame front. One measurable aspect of explosibility is incombustible content. In order to determine whether enough rock dust is applied, 30 CFR1 § 75.403, Maintenance of Incombustible Content of Rock Dust, requires at least 80% incombustible content on the roof, ribs, and floor of underground coal mines. 30 CFR § 75.403-1 further defines the incombustible content as follows: ?Moisture contained in the combined coal dust, rock dust and other dusts shall be considered as a part of the incombustible content of such mixture.? In order to determine the incombustible content of the mine dust, samples of deposited dust from specified areas in a mine must be collected, analyzed, and then compared with the minimum standard of 80%. The traditional low temperature ashing (LTA) approach to determine if a coal and rock dust mixture is compliant with the inerting requirement consumes the coal dust and considers the remaining material to be inert. Compliance with the law is then determined by comparing the measured percentage of inert material of the representative band sample with the pre-established requirement of 80%. The incombustible content of the sample includes rock dust, the amount of moisture as received at the lab, and the inherent ash in the coal. The LTA method is not itself a direct measure of explosibility but is a surrogate that calculates a single parameter associated with large-scale Bruceton Experimental Mine (BEM) explosion test results conducted with dry rock dust. This method assumes a homogenous mixture with no layering of rock dust and coal dust. Float coal dust is a serious explosion hazard if it accumulates on top of the rock dust and is not mixed with the rock dust (12). Mitchell and Nagy (13) studied the effectiveness of water as an inerting agent for the coal dust explosion hazard. The study emphasized that surface water evaporates readily from dusts. Thus, in a passageway where the dust is wet, changes in weather or the ventilation system could dry the dust and make it unsafe in a relatively short period of time. Where adequate rock dust has been applied, this drying effect is not a factor. However, if the mine depends upon the moisture content as part of the incombustible content, fluctuations in the dust surface moisture within a mine can render moisture content an ineffective and inconsistent measure of safety. Additionally, if sufficient moisture is absorbed and subsequently relinquished by rock dust, a cake can form and render the rock dust ineffectual. The trend has long been recognized that mine explosions occur primarily during the winter season when the humidity is low for long periods of time (14, 15, 16). In light of this trend and due to the potential variability of the moisture content of the dust, it may not be prudent to include variable surface moisture in the total incombustible content of the sample. Instead, surface moisture should be viewed as an additional safety measure as long as the rock dust is dispersible. However, moisture limits the ability of the rock dust to disperse and can significantly reduce its capacity to effectively inert propagating explosions (2, 13, 17, 18, 19, 20, 21, 22). Given the methods by which the as-received moisture and incombustible content are determined, dust samples from the 2010 MSHA database were assessed to determine the variability of the moisture content throughout a year and how often the measured as-received moisture might have affected the dust explosibility determination if removed. The findings were then verified by observation in laboratory studies and within the NIOSH OMSHR Safety Research Coal Mine (SRCM).

Feb 23, 2014

By K. M. Kim

An analysis was conducted to determine the effects of blasting on slope stability and downstream comminution processes. To investigate these effects, the extent of blast-induced rock damage and the magnitude of induced stress were examined. This analysis showed that damage may extend up to 500 m (1 MPa, tensile strength) into the rock mass, a distance that is sufficient to have an impact on the pitscale slope over the long term. In addition, the damage zone was calculated using the assumption that compressive waves are the primary agent in microfracturing during blast fragmentation. The calculated damage zone — up to 2.2 m (43 MPa, rock mass compressive strength) — indicates that microfracturing can occur throughout 20-50% of the entire rock mass in the blasting area, depending on the blast geometry, burden and spacing. Finally, an economic analysis was conducted by comparing two assumed blasts in a copper mine. The change in energy required for crushing and grinding was demonstrated using Bond’s law after increasing the blast energy from 180 kcal/t to 350 kcal/t. A total cost saving of 13.3% ($9.4M) was achieved with the increase. However, the benefits of blast-induced microfracturing must be balanced against the potential impacts to slope stability to ensure safe conditions, a top priority in mining operations.

Jan 1, 2014

By D. J. McParland

This paper will deal with some of the considerations which, were involved in the design and construction of the uranium mills in the Elliot Lake area . These plants, eleven in number, range from 1500 to 6500 tons per day milling capacity. Most references are with respect to the seven plants in the Rio Tinto Group which have a combined milling capacity in excess of 20,000 tons per day. In dealing with such abroad subject as mill design, one has the choice, of covering a few specific problems in great detail, or else attempting to cover many subjects superficially and briefly. In preparing this presentation, an attempt has been made to compromise on these extremes, and to select some interesting illustrations which are of general interest in the field of mill design, and of value to persons concerned with mill design broadly, beyond the field of uranium mills.

Jan 1, 1959

By Paul H. Miller

After passage by the Congress, Public Law 95-87, the "Surface Mining Control and Reclamation Act of 1977" was signed by President Carter on August 3, 1977. This law, in its simplest form, was intended to control the environmental effects of surface coal mining and to ensure that mined land is restored to a condition equivalent to that prior to mining. Immediately after the signing, the wheels of government bureaucracy began turning to establish a new federal agency -the Office of Surface Mining Reclamation and Enforcement or OSM -in the Interior Department that would implement the provisions of the Act. Since this took time and because the Congress had not yet provided funding for OSM, a special task force was assembled within the Interior Department to begin the task of writing interim regulations to implement the Act. With respect to the use of explosives, the Act specified that a blasting plan be included in the application for a mining permit. The blasting plan will outline the procedures an operator will use to meet specified environmental protection performance standards. The performance standards established by the Act require explosives to be used only in accordance with existing state and federal laws and regulations and with regulations to be promulgated by the regulatory authority. The regulatory authority was defined as either a state agency operating under an approved state program or the OSM operating under a federal program. As a minimum, it was specified that the regulations should include provisions to require that: 1) a blasting schedule be published in a local newspaper and be mailed to local governments and to all residents living within 1/2 mile of the blasting site . 2) daily notice be given to residents in the area prior to blasting. 3) blast reports be prepared that are maintained for three years and available on request to the public. 4) blasts be designed to prevent injury to persons, damage to property outside the permit area, adverse impacts on underground mines and adverse effects on ground or surface water channels or availability outside the permit area. 5) upon request of residents or property owners within 1/2 mile of the permit area, preblast surveys shall

Jan 1, 1978

By A. L. Martikainen

Booster fans increase air pressure to overcome resistance, the objective being to force adequate amounts of air through distant workings. They are used in areas that are difficult or uneconomic to ventilate with main fans alone. Booster fans are currently permitted in underground coal mines in some countries; the United Kingdom, South Africa, Australia and Canada have been defined as major users. Booster fans are not allowed in the US bituminous and lignite coal mining operations at the present time due to safety concerns. This paper presents the history of booster fan use in coal mines of the United States during the last 90 years. Changes in regulations, as well as advantages and disadvantages of booster fan use, are discussed. Research and petitions for booster fan use are highlighted in order to bring the debate into focus.

Jan 1, 2010

By C. V. Deutsch, O. Babak

A longstanding problem in geostatistics is that kriging usually assigns significantly greater weights to end samples in strings of data than it does to central samples. These weights are theoretically valid, but suboptimal estimates may result when there are geological trends in the variable near contacts, that is, large weights may be applied to samples that are systematically lower or higher than average. A number of ad-hoc corrections exist, each with pros and cons; none are fully automatic with a well-defined measure of optimality. A new method for estimation in a finite domain is proposed. This method is referred to as finite domain kriging. The method is based on kriging with a successively larger number of data. The total number of relevant data (n) is established, and then n kriging matrices are solved. The first matrix has the closest single data value (n-1 weights are set to zero); the second has the two closest data (n-2 weights are set to zero) and so on. The final matrix has all n data. The kriging weights used for estimation are the average of the weights from the n successive kriging runs. Each kriging run is optimal, yet with different smoothing and a different treatment of data at the end of the strings. The result is a set of weights that does not give undue influence to data values at the end of strings. The methodology is developed with examples. Cross validation shows that finite domain kriging outperforms conventional kriging.

Jan 1, 2009

By Alexander Sutulov

1. INTRODUCTION According to the classical economic approach of the open market economy, copper supply should be regulated by market forces which are (a) demand and (b) prices. In fact, demand is of primordial importance because prices are a reflection of supply-demand balance: they go up in times of shortages of supply and down when over-supply situation exists. In the past few years, this basic mechanism of market economy has been under pressure from a number of non-market forces, such as social and monetary problems of sane important copper producing countries; structural changes in copper mining companies through mergers with oil companies; and other factors which greatly contributed to distortion of the basic supply-¬demand equation. As a result, we have faced in the last three years a situation of oversupply rarely seen in the past, with a catastrophic fall in copper prices, huge losses at mines and unprecedented indebtedness of copper producers. This has deep repercussions in the copper business and its future supply outlook. This is particularly so when taking into consideration that high indebtedness and high interest rates conspire against the very survival of some traditional producers. As we write this comment (July of 1985), close to one half of U.S. copper production capacity is closed down, sane of it for good, while the same precarious situation exists in Canada, Australia, Zambia, and some other primary producers who cannot face present low prices with equally low costs. The question is then what this situation means for the medium-¬term future, until the end of this decade, Particularly when taking into consideration the fact that some of the factors influencing it are of a long-term character. 2. SUPPLY-DEMAND SITUATION IN THE LAST FIVE YEARS Since the last boon year, in 1979, when world copper consumption reached a record of 9.8 million metric tons of refined copper, demand dropped to only 9.0 million tons in 1982, when the crisis bottomed out, and then steadily recovered to the level of 9.7 million tons in 1984. Meanwhile, copper production, which in 1979 was only 9.4 million tons, in spite of the fall in demand, grew to 9.7 million tons in 1981 and 1983 and only temporarily was cut to 9.4 million tons in 1982 and to 9.5 million tons in 1984. As a result of this imbalance, hugh copper stocks were accumulated with supply systematically out¬growing demand by over 2 million tons at one time. With the Western World refined copper demand running at an average of 115,000 tons per week, this oversupply was equivalent to between 15 and 18 weeks production, i.e. twice as large as normal. This was immediately reflected in very low copper prices. Another contributing factor to relatively low copper prices was the lack of speculator interest for this commodity. Between 1981 and 1984 the world experienced a very intensive period of wealth distribution, high interest rates and intensive restructuring off world economy and its industrial sector. Therefore, much of the available money was attracted to more lucrative and attractive investments rather than to the lack-luster performance of copper, and for that matter, of the metal sector in general. The much announced and discussed recovery of the U.S. economy since 1983, and particularly in 1984, with an overall growth of the GNP by 6.8% in 1984, happened to be more oriented to the service sector than the industrial sector and therefore this recovery was not adequately reflected in copper consumption nor to metals in general. This put serious doubts about the future demand for copper. Consequently copper prices failed to improve in spite of an apparent fall in stocks and a healthy increase in the demand for copper since 1982. At the time of this writing (July, 1985), although same analysts claim that the available stocks are running at about 8 weeks of supply, which are considered to be below normal, copper prices are still very low at between 65 and 67 cents per pound of copper. Part of the answer may be the normal seasonal slow-down period in the Northern Hemisphere due to summer vacations and

Jan 1, 1986

By Akram Marseet, Andrew J. Petruska, Rik Banerjee

Event cameras are used for their performance in high dynamic-range lighting conditions which are canonical to active mining environments. Direct labeling of event-based image data to train a model to perform semantic segmentation using traditional methods is slow and error-prone. This study proposes a framework to use roughly hand-labeled color images from a mine as an input to an intermediary probabilistic algorithm called alphamatting to generate a ground-truth data set. These high-fidelity labels can be used to train a semantic segmentation model to differentiate the support strap from the roof. This model can then be leveraged to segment an event-based scene to enable autonomous roof bolting. This pipeline has been shown to achieve an accuracy of 88% with a false positive rate of 3%.

Feb 1, 2024