Search Documents

During a period of six months in FY2018, a series of trials were conducted to compare drilling accuracy using two different methodologies and the subsequent impact this had on ore dilution. Testing was conducted at Cracow underground gold mine in Queensland, Australia. The drill rig’s existing alignment process was compared to a new technology system with the following observations: - Using the existing alignment process only 20% of holes surveyed recorded toe points within the +/-300mm (11.8in) tolerance blast-hole deviation. - The new technology was proven to limit rig alignment error, reducing average blast-hole deviation and increasing the number of holes drilled within tolerance by 160%. The increased accuracy reduced stope dilution by reducing over-break of subgrade ore: - Stopes drilled using the new technology recorded 62.6% less average dilution. - This contributed to an overall reduction in dilution for the full year (FY18) of 5 percentage points compared to FY17 - from 22% to 17% (a net decrease of 22.7%). A cost-benefit analysis extrapolated from the trials stipulates that if the new technology were in use for a full 12 months, when applied to FY17 full year data, a 10 percentage point reduction in dilution would represent a net 45.4% decrease, and would result in AUD8.2M (USD5.9) additional ore recovered, with AUD4.5M (USD3.2M) less spent on wasted cost of haulage and processing of diluted ore. As a result, return per tonne would increase 22%, from AUD87 (USD63) to AUD106 (USD77.1). INTRODUCTION Dilution – planned and unplanned – remains a significant cost impairment in the mining process. A series of trials were held over a six-month period in FY18 which established the cost-benefit of new technology as it applies to the alignment accuracy of production drilling rigs in underground mining, thus confirming its ability to limit drilling as one of the causes of dilution. The trials identified three underlying factors affecting drilling accuracy, measurable by blast-hole deviation surveys of planned vs actual toe data. These were; rig alignment error, collar location change/error, and in-hole deviation. The trials involved a comparison of existing rig setup processes and technology, with the new technology (Minnovare’s Production Optimiser system). The trials were undertaken in the same environment; an operating underground gold mine - Cracow Gold Mine. The comparison first revealed the extent to which rig alignment impacts blast-hole deviation. Secondly, the new technology was proven to limit rig alignment error, thereby reducing average blast-hole deviation and increasing the number of holes drilled within tolerance by 160%.

Jan 1, 2019

By G. X. Wang

The nonliving dried water hyacinth (E. crassipes (Mart.) Solms) roots were investigated for biosorption of cadmium and lead and other heavy metal ions in aqueous solutions. Dried water hyacinth roots, when suspended in solution, strongly and rapidly sorb several different metal ions. Factors such as reaction time, pH, initial concentration of metal ions, presence of other metal ions and biomass concentration were investigated. Metal ions, including Cd2+ and Pb2+, were bound to the root in a very pH-dependent manner, with the binding increasing after about pH 3. High levels of removal were obtained. The adsorption was shown to follow the generalized Langmuir adsorption equation. The relative affinity of the roots for lead is greater than for cadmium. The maximum sorptions of the roots were about 33 and 86 mg/g for cadmium and lead, respectively. Only 15-20 minutes were required for the process of uptake onto the biomass to occur. The batch sorption kinetics of the uptake of cadmium and lead can be described by an apparent first-order reversible reaction model. The roots could be regenerated after the metal ions were stripped. A solution of CaCl2 in acidic medium appeared to be the best eluant for desorbing the sequestered Cd and Pb completely at pH 3. The kinetics of the metal stripping process was quite rapid. Successful desorption of Cd and Pb from the biomass by acidic CaCl2 solutions revealed that the metal uptake phenomenon is reversible, implying physical sorption of Cd and Pb.

Jan 1, 1997

By H Vigil, G. Peach

Long tunnels with only one access shaft pose many program problems for logistics, combine these with the requirement to drive directly out under the seabed for 10.2 km, and the program issues become even more challenging. The Musaimeer outfall tunnel was one such tunnel and to meet and eventually improve on the planned completion date required a complex and extensive management of all tunnel logistics required to support consistent tunneling for a two-year period. This technical paper will discuss the management issues and solutions implemented to meet the challenges of the Outfall tunnel construction.

Dec 1, 2022

By S. K. Kawatra

Outokumpu Electronics has designed a new on-line coal slurry ash analyzer, based on an instrument developed at Michigan Technological University. The primary goal was to build an accurate instrument at the lowest possible cost. The instrument determines ash content from measurements of x-ray backscatter, iron Ka fluorescence, and low-energy y-ray absorption. It is capable of measuring the ash content with a standard error of 1.1% ash over an analysis range of 9-21% ash and 7-22% solids. The analyzer was tested on coals from United States, Poland, Great Britain and the USSR.

Jan 1, 1992

By C. Vass, A. Noble

"The chemical treatment of mine-influenced waters is a longstanding environmental challenge for many coal operators, particularly in Central Appalachia. Mining conditions in this region present several unique obstacles to meeting NPDES effluent limits. Outlets are often located in remote areas with challenging terrain where conditions do not facilitate the implementation of large-scale commercial treatment systems. Furthermore, maintenance of these systems is often laborious, expensive, and time consuming. Many large mining complexes discharge water from numerous outlets, while using environmental technicians to assess the water quality and treatment regime multiple times per day. As an alternative solution, this paper describes the ongoing research and development of automated chemical treatment systems for mine water discharges. The current work explains the development of a bench-scale prototype that has been used to evaluate various monitoring, notification, and control strategies. Results from this testing are compared to present day practices to show the costs and benefits of implementing an automated treatment and monitoring program. INTRODUCTION Background The National Pollution Discharge Elimination System (NPDES), per Section 402 of the Clean Water Act, requires permitting of all point source discharges from coal mines. This program dictates that all water leaving a permitted boundary, whether it be process water or storm water, must leave through a monitored NPDES outlet. These permitted NPDES discharge points, also denoted outlets, outfalls or monitoring points, must meet a rigorous set of effluent limits to maintain compliance. Common effluent limits monitored by coal companies include but are not limited to iron, manganese, aluminum, total suspended solids (TSS), and pH. Raw mine water is often deficient in meeting these effluent limits, and as a result, various treatment processes are required to bring the water into compliance prior to environmental release. Depending on the mining and geologic conditions, water monitoring and treatment programs can constitute a significant operating cost for the mine operator. In Appalachia, acid mine drainage (AMD) constitutes one of the most significant and widespread water quality challenges that must be treated per NPDES guidelines. AMD is a general lowering of water pH that occurs when water and sulfide minerals interact within oxidizing conditions in coal and metal mining. Acid Rock Drainage (ARD) is a similar term that applies more generally to non-mining causes such as highway construction and other large-scale excavations. Today, mine influenced waters (MIW) is becoming more popular as the general term referring to all types of mining-induced water issues. AMD has been researched substantially over the last 30 years, with investigators studying various causal mechanisms and treatment strategies (e.g. Gazea, 1996; Ziemkiewicz, 1998; Skousen, 2000; Kleinmann, 2001; Johnson, 2003; Akcil, 2006; Kalin, 2006). This research has produced several pragmatic results, which provide numerous methods to predict, prevent, and treat AMD."

Jan 1, 2016

By Lourens Scheepers

Mining induced seismicity and rockbursts have been part of the deep level gold mining industry in South Africa for many years. One could be forgiven for thinking that we should know everything there is to know by now to have rockbursting under control to a level that it has minimal impact on safety and production. Well, we don’t… There are things we know that we know, and they are implemented, or should be. There are thigs we know that we don’t know, and they are researched, or should be. There are things we don’t know that we don’t know, and, well, we don’t know… We know that seismicity and the associated potential for rockbursts generally increase with an increase in stress (increase in mining depth and/or mining span and creation of remnants) and proximity to faults and dykes. We know there are a number of potential sources of events in a mine; that is: mining abutments, pillar abutments, mining faces and geological structures (faults and dykes). We know there are a number of event mechanisms associated with these sources; that is: slip on a geological structure, shear through intact rock and bursting of the rock near the edge of a mining excavation. One of the tools used more and more and with increased success to identify event source mechanisms is Moment-Tensor analysis (MT). This typically assist in differentiating between three event mechanism components: volumetric deformation component, axial deformation component and slip / shear component. The insight gained from MT assist greatly in identifying the most likely event source to assist in understanding the rockmass response to mining. We know that the seismic response in our mines are mining induced (not natural). This may seem trivial, but it is important to realise that we influence the seismic response with the way we mine, and by how much we mine (extraction ratio). Therefore we put design rules and strategies in place to reduce the seismic hazard and we install rockburst support in our mining excavations. We know the seismic response to mining is influenced by the properties of the rockmass, including strength, stiffness and brittleness, but quantifying its influence is typically more difficult than expected. We know numerical modelling can improve the engineer’s understanding of the potential rockmass response associated with designed mining layouts and strategies. For our environment (narrow, tabular large area) elastic boundary element modelling remains the most convenient and practical approach, but it overestimates the stress at mining abutments and underestimates the stress further away from these abutments. Adding a crushing (based in limit equilibrium) modelling approach vastly improves the boundary element modelling ability to simulate the deformed (interpret fractured) zones and associated redistribution of stress. We don’t know how to quantify what an acceptable seismic risk is. We don’t know if we can mine remnants at an acceptable seismic risk. Some remnants are extracted surprisingly easy, others serve us with devastating rockbursts. The limit equilibrium modelling shows potential to significantly improve our ability to quantify the rockburst risk. We don’t know if large-scale preconditioning is possible and will be effective to significantly reduce the seismic risk associated with remnant and pillar mining. Research is required (and has been initiated). Vast areas of ground have been extracted historically in the South African gold fields. Most gold reserves are now in deeper ground (4000 m) and historic remnants (areas left before due to mining difficulties) as well as pillars (regional stability pillars). If we cannot find ways to extract these reserves at acceptable risk levels, the future of the South African gold mining industry is very short.

Apr 26, 2022

By T. McCallum, C. Cooper, C. Lewis

"Following a successful solvent extraction (SX) pilot plant demonstration in 2016, CYANEX® 600 has been used commercially to recover molybdenum from concentrate leach liquor since March 2017. Consistent with the piloting results, the commercial plant has achieved expected molybdenum recovery, a significant reduction in base consumption, and a step-change improvement in physical performance. This paper highlights the optimization activities and plant performance from startup through normal operation. INTRODUCTION Historically, tertiary amines have been the most commonly used extractant for molybdenum and rhenium recovery. Tertiary amines utilize a protonation of the ligand combined with an anion exchange mechanism as proposed in equations (1-2). R3N + H+ ???R3NH + (1) 4R3NH+ + Mo8O264- ???(R3NH+)4Mo8O264- (2) In addition to the transfer of Mo and Re, the amine transfers acid and other anions to the strip liquor. The undesirable transfer of other species increases base consumption during stripping, impacting operating costs. Additionally, lower solubility of molybdenum-amine complexes create operational challenges, resulting in diminished physical performance. The presence of colloidal Si in concentrate leach liquors and the formation of Pickering Emulsions adds to the physical plant performance challenges with the amine extractant. CYANEX® 600, a phosphinic acid-based extractant, uses a cation exchange mechanism proposed by equation (3). 2(H2R2) + MoO22+ ??(HR2)2MoO2 + 2H+ (3) The cationic exchange mechanism eliminates chemical transfer of acid and other anionic impurities and avoids some of the physical challenges of the amine extractant (emulsion and 3rd phase formation). In addition, the reagent offers high selectivity for Mo over Re, which may be desirable in certain moly pressure oxidation (POX) flowsheets. Alkali base (ammonium hydroxide, sodium hydroxide, sodium carbonate, etc.) is used for molybdenum stripping. Therefore, reduction or elimination of chemical acid transfer from extract can significantly reduce base consumption in strip. Extensive laboratory and pilot plant testing was completed to evaluate the use of CYANEX® 600 for molybdenum recovery at Freeport-McMoRan’s Bagdad operation. The test work and pilot demonstration confirmed a reduction in base consumption along with improved selectivity. In addition, the evaluation highlighted a step-change improvement in physical performance over the incumbent amine extractant. The decision was made to convert the commercial operation to CYANEX® 600 in March 2017."

Jan 1, 2018

By Linda J. Dahl

The U.S. Department of the Interior, Bureau of Mines is developing a process to selectively extract manganese from oxide ores as part of its in situ leach mining research program. The Bureau is conducting site characterization studies of two manganiferous iron-formation deposits which include: drill core, regional stratigraphic relationships from the existing geologic database, ore body geometry, geologic structure, hydrologic conditions, proximity of ore minerals to the leach fluid paths, surface subsidence potential, and data collected from laboratory leaching experiments. This information is being used to evaluate the technical, environmental, and economic feasibility of in situ leach mining of manganese for these two deposits. This paper will focus on the stratigraphy, mineralogy, ore textures, fractures, permeability, and porosity as they relate to in situ leach mining.

Jan 1, 1992

By Gabriel Böde Jimenez Leon, Michael Karmis, Christopher Newman, Zach Agioutantis

"When utilizing high recovery underground mining methods, such as longwall or high-extraction room-and-pillar mining, the movement and deformation of the overburden propagate toward the surface and may affect the integrity of overlying surface streams (Peng et al, 1996). Published studies cite three major mechanisms of subsidence as most likely to impact streams: displacement, slope and strain. While subsidence-induced vertical displacement cause little structural damage to the stream bed, it may create adverse drainage and stream flow issues as the subsidence trough allows for ponding (Dawkins, 2003). Subsidenceinduced changes to the slope, or tilt, of a stream may have adverse effects on water flow. As the stream enters the subsidence trough, the gradient increases providing potential erosion control problems. When exiting the subsidence trough, a reduction of the gradient may inhibit stream flow, causing localized ponding (Peng, 2008). While vertical displacement and tilt both may have detrimental effects to surface streams, the resulting strains have been documented as being the most damaging to surface streams and structures causing distortion, fractures, or failure (Singh, 1992). When stream beds are subjected to high tensile strain, tensile cracks may form at the surface level allowing for the direct loss of stream flow through fissures. When stream beds are located in areas of high compressive strain, rock layers forming the stream bed can fail as the stream bed ruptures, upward, blocking stream flow or having the stream diverted into the fracture zone at the base (Iannacchione, et. al., 2010).Recent investigations on the effects of underground mining on surface bodies of water suggest that to determine the degree of stream impact one must also consider the geologic structure and thicknesses, surface topography, watershed drainage areas, width of river bed and rate of mining. Due to the complex nature and number of parameters affecting surface streams, subsidence modeling tools and software packages should be implemented throughout all stages of subsidence planning, prediction and control. The Surface Deformation Prediction System (SDPS) utilizes the influence function for the calculation of final subsidence deformations with respect to the angle of influence, supercritical subsidence factor as a function of the percent hard rock, edge effect offset distance, and surface topography. Developed more than 25 years ago, SDPS has been continually updated with new analysis and prediction features, providing a reliable and versatile program for subsidence management methodologies. Most recently, the program has been updated to evaluate the effect of varying surface topography in the prediction of horizontal displacements, referred to as ground strain, allowing for the accurate three-dimensional representation of surface deformations in mountainous terrain (Agioutantis and Karmis, 2014). Ground strain has become one of the predominant deformation indices used in the evaluation of potential damage to surface structures (Karmis et al., 1995). Ongoing work with SDPS software seeks to investigate the calculation of ground strain in SDPS and its ability to accurately and realistically predict damage to surface streams due to underground mining operations."

Jan 1, 2015

By H. Askari-Nasab, B. Osei, K. Awuah-Offei

The U.S. coal mining industry consumes approximately 142 billion kWh/a of energy. The U.S. Department of Energy estimates that the industry’s annual energy consumption could be reduced by 49%. This constitutes nearly $3.7 billion of potential savings on coal production costs at 5.3¢/kWh of energy. Additionally, with climate change regulation on the horizon, any benefits from energy savings in the near future are compounded by associated reductions in CO2 emissions. Research indicates that operating conditions significantly affect energy efficiency. Modeling and simulation have been shown to be a cheap and reliable means of evaluating the effects of process interactions and operating conditions. The goal of this work was to apply stochastic process simulation to model the energy efficiency of a typical truck-and-shovel mining system and use the model to evaluate production strategies to improve energy efficiency. The research team conducted energy audits of truck-and-shovel overburden removal and used the results to develop regression models describing truck and shovel fuel consumption. The team then built a stochastic simulation model of the truck-and-shovel overburden removal operation and used it to assess a variety of improvement measures by simulation experimentation. Valid fuel consumption models for shovel loading and truck haulage have been formulated, based on the energy audit results. Valid stochastic process models of truck-and-shovel operations have been formulated to study energy efficiency. The following strategies, in decreasing order of impact, provide the most energy savings for truck-and-shovel overburden removal at the mine: (1) shorten haul roads, (2) increase shovel capacity and (3) increase shovel utilization through optimal truck matching. Additional data will be required to adequately describe operator effects on energy efficiency.

Jan 1, 2011

By Martin B. Zimmerman

It is becoming evident that traditional methods of econometric analysis are inadequate in estimating-the long-run supply of minerals. Econometrics is limited to extracting estimates from observations of the theory predicts that the least cost deposits will be exploited first.1 The estimation of parameters from past data then must lead to biased projections of the future. Mining conditions in the future will be worse than in the past and it is the impact of the future conditions on cost that we need to know. In this paper we present a methodology for dealing with this problem. We estimate a "cumulative cost" function that yields the long-run marginal cost of mining as a function of cumulative output produced over time.2 This is relatively easy to do for coal mining in the United States where exploration for new deposits is not a major factor in supply. The first step of the procedure relates cost to the rate of output and to the geological conditions of the mine. The second step combines geological information on remaining deposits with the cost function to yield the cumulative cost function. A central theme of both these steps is the interaction of economics with geology. The best deposits are selected first and in each step of the estimation allowance must be made for this fact. The problem of depletion is part of the general problem of structural change. The change through depletion in the nature of the exploitable mineral stock is only one factor that calls for an analysis sensitive to the changing circumstances of the industry. The factors impinging most heavily on the coal industry today are the strict environmental regulations legislated

Jan 1, 1977

By John W. Tieman

The increasing magnitude of our nation's pollution problems seems to stem from two main factors: urbanization and technical advance. In 1920, less than half the country's 106 million people lived in cities. Forty years later, the urban population accounted for 70 percent of the nation's 179 million. It is predicted that by the end of the century, 95 percent of the U. S. population, estimated at 280 million, will live in urban areas. As these people live increasingly in city concentrations, their residues also concentrate. With technological advances to support the increasing population, the variety and quantity of goods that we use also increases. New materials and processes result in increases in pollutants, some of them new. The harmfulness of these pollutants is sometimes known, but sometimes only suspected. One pollutant of concern at the present time is sulfur dioxide, the product of combustion of sulfur-containing fuels. Research on processes to remove sulfur oxides from flue gas has been in progress for many years. Pioneers in this field were the British who, in the early 1930's, installed a full-scale flue gas scrubbing unit on a 120 MW boiler using alkaline water from a Thames estuary plus chalk. Since that time, various methods have been studied by many investigators. Federal laws covering air pollution started with the 1955 Air Pollution Control Act. With the advent of the Air Quality Act of 1967, and subsequent publishing of criteria and available technology for control of sulfur oxides in January 1969, the clamor for information on commercially available control techniques to remove sulfur from fossil fuels has rapidly increased. Although many state-of-the-art papers have deluged the literature during the past several years, the research going on in the area of sulfur oxides control is of such importance that periodic reviews are justified. It is the purpose of this paper, therefore, to again review the state-of-the-art, but this time from the stand-point of what is immediately commercially available

Jan 1, 1972

By J. M. Keane

SMEThis loaner is concerned with important criteria relative to the design of small flota¬tion concentrators. For the purpose of this discussion a small flotation concentrator is defined as a facility having a designed ore feed rate of 1,000 metric tons per day (MTPD), or less. The decision to design and construct a small flotation concentrator is the culmination of a series of logical steps relative to the ex¬ploitation of a potential ore body. The information required for a rational and timely decision regarding plant design and construction is usually contained in a feasibility report. The information required in a thorough feasibility report has been summarized (1) (2) as follows: Type of mine or plant and proposed daily, monthly, and yearly production of all intermediate and final products. Quantity of indicated ore reserves. Location of project illustrated by a map showing surroundings, trans-portation facilities, and existing utilities.

Jan 1, 1980

By J. D. Noll

An effective technique to minimize miners? respirable dust and diesel exposure on mobile mining equipment is to place mine operators in enclosed cabs with designed filtration and pressurization systems. Many factors affect the performance of these enclosed cab systems, and one of the most significant factors is the effectiveness of the filtration system. High-efficiency particulate air (HEPA)-type filters are typically used because they are highly efficient at capturing all types and sizes of particles, including those in the submicron range such as diesel particulate matter (DPM). However, in laboratory tests, minimum efficiency reporting value (MERV) 16 filters have proven to be highly efficient for capturing DPM and respirable dust. Also, MERV 16 filters can be less restrictive to cab airflow and less expensive than HEPA filters. To verify their effectiveness in the field, MERV 16 filters were used in the enclosed cab filtration system on a face drill and roof bolting mining machine and tested at an underground limestone mine. Test results showed that DPM and respirable dust concentrations were reduced by more than 90% when the cabs were properly sealed. However, when the cab door was opened periodically throughout the shift, the reduction efficiency of the MERV 16 filters was reduced to 80% on average.

Feb 1, 2014

By James C. Barker

Alaska?s known mineral endowment includes some of the largest and highest grade deposits of various metals, including gold, copper and zinc. Recently, Alaska has also been active in the worldwide search for sources of rare earth elements (REE) to replace exports now being limitedby China. Driven by limited supply of the rare earths, combined with their increasing use in new ?green? energy, lighting, transportation, and many other technological applications, the rare earth metals neodymium, europium and, in particular, the heavy rare earth elements terbium, dysprosium and yttrium are forecast to soon be in critical short supply (U.S. Department of Energy, 2010). The REE, accompanied by other high field strength metals (such as Nb, Zr, Ti, Th, W), are associated with alkaline complexes of the Hogatza Belt in northwest Alaska; peraluminous tin-granites of the Ruby batholith in central Alaska and the Porcupine plateau in the northeast; and peralkaline intrusive complexes in the southwest Alaska Range west of Anchorage, and on Prince of Wales Island in southeastern Alaska. Limited evidence suggests that the heavy REE are associated with deposits that became more highly evolved by late hydrothermal processes.

Jan 1, 2012

By G. Hoffmeyer, I. Ream

"Several copper projects exclusively utilizing in-situ recovery methods are currently under development in Arizona. Favorable conditions for In-Situ Copper Recovery (ISCR) include a saturated orebody, fracture hosted mineralization, hydraulic conductivity sufficient to effectively inject and recover solutions using wells, and a relatively flat background hydraulic gradient. Safe operation of an ISCR project requires that the operator have the ability to induce and maintain localized hydraulic gradients, thereby controlling the movement of injected and recovered solutions. Benefits of ISCR include reduced initial capital, and a greatly reduced environmental footprint. THE ISCR METHOD EXPLAINED The method chosen to extract a mineral from a deposit is driven by characteristics such as its size, grade and depth of burial. Large lower grade deposits that require significant excavation to access using surface methods are potential candidates for in-situ recovery. ISCR may also be ideal for smaller deposits due to the lower initial capital. However, regardless of the size of the deposit, certain hydrogeologic conditions must be present for ISCR to be successful. In-situ recovery methods do not require excavations of rock from the surface or underground, resulting in a dramatic reduction in surface disturbance when compared to conventional mining. With the ISCR method, what is visible above ground is the processing plant, well heads, piping, process solution impoundments and evaporation ponds. There are no waste rock piles, tailings impoundments, leach pads, or impacts associated with blasting and hauling. Other benefits include reduced initial capital, reduced dust and noise, and lower water use. Early testing of the in-situ copper recovery method by Occidental on the Van Dyke deposit east of Phoenix and by Kennecott at Safford Arizona in the 1970s produced encouraging results, but the permitting regime for a large-scale operation was not yet in place. Additional testing and commercial application of in-situ copper recovery techniques have expanded since the 1980s, most commonly in conjunction with open pit or underground mining operations. For example, several operations in Arizona (San Manuel, Miami East and Tohono) have used in-situ techniques to extract additional copper following conventional mining from parts of the deposits adjacent to open pits or underground workings. Where the rock has been broken up by conventional methods, the method is called “in-place” leaching. The US government has also been involved in assessing in-situ techniques. For example, joint research was conducted by the US Bureau of Mines and industry on the Santa Cruz deposit in Arizona; and both federal and state agencies have been involved to establish the comprehensive permitting regime that exists today. Currently there are several projects in Arizona being evaluated as stand-alone ISCR operations."

Jan 1, 2016

By Grant A. Brackebusch

Paste tailings disposal was successfully implemented at the New Jersey mill in Kellogg, ID with two different types of ore feed, a gold ore and a silver ore. The purpose of this paper is to describe the production of paste tailings, including operational problems during commissioning, and also highlight the environmental and economic benefits that were realized versus conventional tailings disposal such as the recycling of process water, increased shear strength and reduced permeability of the tailings mass, and reduced environmental permitting.

By Paul B. Queneau

Formulation and commercial utilization of solid-waste incinerator slag by-product is the focus of this paper. Particular attention is given to iron aluminosilicate melts having compositions similar to that of nature's basalt The earth?s crust can be viewed as an environmental laboratory for predicting stability of various silicates; small-scale laboratory experiments are necessary to confirm findings there from. An ideal slag consumes flux additives at acceptable cost, is compatible with furnace refractory, flows readily from the furnace, and has physical properties suitable for its commercial utilization -all within the critical constraint that the slag is environmentally stable. Examples of successful solid waste slagging practice, including tonnage, utilization and pricing, are provided from metallurgical and waste treatment operations of North America. Western Europe and Japan.

Jan 1, 1991

By J. D. Noll, J. A. Organiscak, A. B. Cecala

Over the past decade, a substantial effort has been made to improve the air quality inside enclosed cabs of both underground and surface mobile mining equipment to reduce respirable dust exposures by the equipment operators. As part of this effort, the U.S. National Institute for Occupational Safety and Health, (NIOSH) completed a comprehensive laboratory study that determined the significant factors for cab filtration and pressurization systems. From this information, a major underground mining equipment manufacturer designed a filtration and pressurization system that was incorporated into the enclosed cabs of its equipment. A long-term evaluation was performed on the effectiveness of this filtration and pressurization system to improve the air quality in the enclosed cabs of two different pieces of equipment, a face drill and a roof-bolter machine, at an underground limestone mine. This long-term evaluation demonstrated a significant reduction in dust levels between outside-to-inside cab respirable dust concentrations. During this evaluation, a modification to remove one of the filters on the roof-bolter machine simplified the design without sacrificing the system’s efficiency. Tests using particle count instruments performed during nonproduction time periods on both pieces of equipment indicated protection factors greater than 100 when comparing respirable-sized dust particles inside the enclosed cab relative to outside.

Jan 1, 2012

By I. A. Tinto

Labrador City is located in the southwestern portion of Newfoundland-Labrador, approximately 965 kilometers north-east of Montreal. The mine and beneficiation complex of the Iron Ore Company of Canada, known as the Carol Project, is situated 535 metres above sea level in a climatic region characterized by cold winters and short, cool summers. History The iron Ore Company of Canada commenced work in the area in 1949, however, it was not until 1958 that the decision was made to proceed with mining operations. The ore body consists of Specular Hematite (Fe203) and Magnetite (Fe304) with small quantities of Limonite and Geothite. The average grade of the ore bodies is 39% iron.

Jan 1, 1985