Search Documents

By R. K. Zipf

Recent scientific studies by researchers at the National Institute for Occupational Safety and Health (NIOSH) and the U.S. Army Corps of Engineers (USACE) presented the worst-case explosion pressures that can develop if a methane-air mixture of a certain composition and dimension accumulates and ignites within a sealed area of a mine. The Mine Safety and Health Administration (MSHA) issued its final rule on sealing of abandoned areas which considers potential explosion pressures and the risk of achieving the necessary conditions. The new MSHA seals regulation has increased the pressure design criteria an order of magnitude beyond the old standard of 140 kPa (20 psi) to 800 kPa (120 psi). However, there still are major knowledge gaps pertaining to seals and sealed areas including: (1) the composition of the sealed area atmosphere and how it changes in time and space, (2) explosion pressures that might actually develop within sealed areas, (3) engineering procedures to follow when designing seals and seal installations, and (4) guidelines to manage the atmosphere within sealed areas with monitoring or inertization. NIOSH has initiated a seals research program with collaborators from Safety in Mines Testing and Research Station (SIMTARS) in Australia, West Virginia University (WVU), the Naval Research Laboratory (NRL), and USACE. Highlights of progress so far include: (1) construction of a gas explosion tube at Lake Lynn Laboratory for studying large methane-air explosions, (2) computer simulation of the fluid dynamics of high pressure methane-air explosions, (3) development of seal analysis methods considering construction materials, reinforcement and the seal foundation, and (4) development and testing of innovative seal designs that utilize inexpensive, readily-available rock rubble to resist high explosion pressures. NIOSH researchers aim to provide sound engineering guidelines to better address the new MSHA seal regulations. DISCLAIMER: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By Wei Victor Liu, Omer Faruk Ugurlu, Chengkai Fan, Bei Jiang

Accurate prediction of truck productivity plays a pivotal role in improving the efficiency and profitability of openpit mining operations. This paper proposes a deep neural network (DNN) model to overcome the challenge of predicting truck productivity in openpit mines. The prediction model was built using eight variables and was optimized by considering different train-test split ratios, numbers of hidden layers and neurons, and activation functions. The proposed model’s performance was evaluated using various metrics and compared with other commonly used machine learning algorithms. The results showed that the proposed model outperformed traditional machine learning models by achieving higher prediction accuracy. Moreover, a single-variable sensitivity analysis showed that haul distance is the most influential variable for predicting truck productivity. This study marks a pioneering effort in employing DNN to predict truck productivity in openpit mining, signifying a notable advancement in the field.

Jul 1, 2024

By Ralph L. Merklin

One of the most commonly employed set of calculations in mill design and research is the material balance, known in wet beneficiation plants, as an Ore and Water Balance. For mill designers, the balance is one of the principal requirements in determining the proper size of launders, pipelines, process equipment, etc. In process development, one of the major goals is the establishment of an optimum balance. The usual procedure for calculating a material balance involves a manual technique utilizing reference tables, pre -obtained data, and a slide rule or desk calculator. With these, the engineer must perform a series of calculations which are repetitious in nature and time consuming. Figure I is the flowsheet of the grinding and flotation circuits for a copper concentrator. The initial ore and water balance was calculated manually and required approximately 24 manhours. Later, a number of changes were made in the balance, each of which required an average of 8 manhours.

Jan 1, 1967

By Randall D. Peterson

Economic operation of a mine ventilation system must include some means by which operating costs can be quantified and evaluated periodically. Current practice at most mines relies upon the best judgement of foremen, engineers and managers to identify high cost or problem areas in the system and to estimate potential costs and benefits of work proposed to reduce inefficiencies. The problem with this is that significant savings can be overlooked or sub-economic projects may be undertaken when sufficient attention is not paid to the interrelationship between airflow characteristics and corporate financial criteria. In order to accurately determine costs and benefits it is necessary to view the solution of each potential ventilation problem as a separate economic opportunity.

Jan 1, 1993

By Yuanyuan Wang, XUEWEN WANG, Jinzhi Wei, Ligang Wen, Muxin Jia, Zhengyao Li

The abstract discusses the use of disodium carboxymethyl trithiocarbonate (D8) as an effective depressant in the flotation separation of stibnite and pyrite. The study investigates the mechanism behind D8's selective inhibition of pyrite, utilizing techniques like micro-flotation experiments, contact angle measurements, infrared spectroscopy, adsorption capacity analysis, and zeta potential measurements. The findings reveal that D8 physically adsorbs onto both pyrite and stibnite, but its adsorption capacity on pyrite is significantly higher. This adsorption enhances the hydrophilicity of the pyrite surface, hindering the adsorption of the collector and effectively depressing pyrite flotation, while having minimal impact on stibnite floatability.

Mar 14, 2022

By William H. Dresher

A recent report to President Reagan from the Business-Higher Education Forum, entitled, "America's Competitive Challenge: Need for a National Response," (1) observes that in the recent past, ". . . much of that research, which is necessary for major breakthroughs and sustained productivity improvements, was redirected to short-term objectives ... At the same time, American universities, which conduct more than half of the nation's basic research, have suffered from an accumulated under-investment in facilities and equipment amounting to an estimated $1-4 billion." Also contributing to the decline in America's productivity, the report said, are "...weak technology transfers between government and industry and between universities and industry..." This report as well as other recent reports and articles have, reopened a subject which has long been debated but rarely resolved-- the interaction between the academic community and industry in the sponsorship and conduct of research. The subject is unfortunately, too often treated as a controversial issue involving ethics and the profit motive when, in fact, the two branches of society -- industry and academia -- are necessarily part of the same system. I would like to speak to you today on the subject of university-industry interactions and to some extent discuss the role of government in such interactions. Finally, I will make some remarks as to how this subject applies to the mining industry.

Jan 1, 1984

By J. D. Miller

Pilot-scale tests indicate that effec¬tive concentration of fine gold from Colorado River sands can be achieved by flotation with the air-sparged hydrocyclone. The fine sands (55% minus 400 mesh and 0.01 opt*) from gravity concen¬tration were processed with a 5-cm air-sparged hydrocyclone (capacity -1.0 tph dry solids). Concentrate grades as high as 5.0 opt were produced in a single stage at a recovery of 75.0%. The separation efficiency was significantly better than that achieved in conventional batch flotation experiments.

Jan 1, 1985

By R. J. Visintainer, J. M. Furlan

"Due to the time-consuming nature of froth testing in a laboratory environment, practical limitations require the development of a method of applying a single set of performance test data (Visintainer and Whitlock, 2012) obtained for a single froth pump at a given speed to a range of froth pump speeds and sizes, % air content and liquid viscosities. Head, efficiency and flow all vary as functions of both liquid viscosity and air content. As such, it is necessary to develop a technique that can be used to interpolate from existing test data in order to predict froth performance for pumps of various sizes running at variable speeds. Details of the technique developed in order to achieve this goal, as well as the insights gained from analysis of the resulting regressions, are discussed. Additionally, comparisons are made between the performance predictions of this test-derived method and those of the Hydraulic Institute standard for the effects of liquid viscosity on centrifugal pump performance (ANSI, 2010).IntroductionPump performance data (Visintainer and Whitlock, 2012) has been collected for a froth pump using an experimental loop outfitted with an array of pressure transducers, mass flow meters, an inverted U-loop, magnetic flow meter and an assortment of other instrumentation. Experiments were performed on pure water, water and air, pure corn syrup, and corn syrup and air. Data was obtained for % air contents of 0-30% and viscosities of 1- 15,000 cSt at eight specific valve positions (eight different flows as a percentage of best efficiency flow points) and the viscosity was changed by allowing the system temperature to increase during testing. The test pump is a 710-mm diameter impeller, GIW HVF, open shrouded, vented design that has its discharge axis oriented at 45° upward from the horizontal. A schematic diagram of the froth pump test loop can be seen in Fig. 1."

Jan 1, 2015

By Alexander N. Winchell

"Location. The iron formation of the Gogebic district (including the Penokee) comprises a narrow belt south of the western part of Lake Superior extending from Michigan for a considerable distance into Wisconsin. From the mouth of the Montreal River (about twenty-five miles west of Ashland) the iron formation is only about twelve miles distant, but it is about twenty miles south of Ashland. Beginning on the east at a point about eight miles east of Wakefield, Mich., it extends through Sunday Lake, Bessemer and Ironwood in Michigan, and thence south of west through Hurley, Wis., and only a short distance south of Mellen, Wis. About eight miles westward from Mellen, the formation disappears, but six miles further west it is known to reappear and continue thence for about eight miles. The total length of the range is about sixty miles, two-thirds of this distance being in the State of Wisconsin; but nearly all of the ore has been obtained from the eastern third of the district, which is in the State of Michigan.History. This iron range was first noted in 1848 by Dr. Randall, assistant geologist to Dr. David Dale Owen, while following the fourth principal meridian northward. It was also reported by Charles Whittlesey in an account of a survey made in 1849, and published by Owen in 1852. Analyses of the iron ore are given with the following account. ""The bed of magnetic iron ore south of Lac des Anglais is of extraordinary thickness,25 to 60 feet. * * In the wild and deep ravines where the Bad River breaks through the range, there is a cliff of slaty ore * * * probably three hundred feet thick. * * * I estimate more than one-half of this face to be ore, and in places the beds are from ten to twelve feet in thickness, with very little inter-mixture of quartz * * * . The position of the best exposures of ore which I saw is such as to require from eighteen to twenty eight miles of transportation to reach the lake."""

Jan 1, 1920

By Philip Antunes, A. E. (Tony) Reschke

"INTRODUCTION Tunnel Boring Machine (TBM) operations require the injection of material into the annular tail voids as the machine advances ahead of the segmental concrete lining. This annular gap is created because the cutting diameter of the TBM has to be larger than the outer diameter of the concrete segments of the tunnel lining. Fundamentally, the two basic types of annular grout are thick, concrete like mortars and thin, mobile, two-component grouts. While some European countries seem to still favor the concrete like mortars, from a global perspective it is now the two-component type grouts that dominate the industry. Two-component type grouts are comprised of an “A” component grout (typically cement, flyash, bentonite and a retarder/stabilizer) and a “B” component accelerator (sodium silicate or water glass as it is sometimes known). They are thus sometimes referred to as A/B type or bi-component grouts and were pioneered by the Japanese over 30 years ago. They offer a host of operational benefits over thick mortars, such as reduced settlement (Feddema et. al., 2001), effective penetration of the void space, with less energy, and reduced strain on the segmented linings (Robinson et. al., 2007). Two-component grouts are highly mobile and can be pumped many kilometers. The use of a retarder/stabilizer can also extend the shelf life of the “A” component grout for several days while the early strength of the accelerated grout stabilizes the ground and supports the segmental liner almost immediately. The batch plants that prepare the two-component grouts use one of two possible mixing methods for preparing the “A” component grout. The simplest plants use paddle type mixers and numerous tunnels worldwide have been successfully grouted using this technology. However, a superior type of mixer is available, namely the high shear colloidal mixer. Keller Colcrete successfully pioneered the development of the colloidal mixer back in 1937 and for over 75 years colloidal mixers have been internationally recognised as the most efficient method of mixing cement based grouts (Houlsby, 1990). These mixers are used in grout preparation for radioactive waste encapsulation, hydro dam grout curtains, soilcrete jet grouting, soil nailing, and numerous other geotechnical applications. In tunnelling, these mixers are also used for ground treatment, compensation grouting and for the preparation of bentonite lubrication for pipejacking. It has been only within the last decade however that these high-shear colloidal mixers have been adapted for use in the preparation of two-component grouts."

Jan 1, 2016

By Fred Delabbio, Sverker Hartwig

As openpit copper operations transition from surface mines to underground, the speed of underground infrastructure construction prior to production is critical for maximizing the value of the project. Typically, the preferred underground bulk mining method is block caving. In preparation for future underground projects, Rio Tinto made the strategic decision to invest in a step-change program that would develop system solutions to reduce the construction time of block caves. The program focused on improving safety and doubling or more the construction speed of both vertical shafts and horizontal infrastructure compared to existing drill-and-blast rates. After an extensive selection process, Rio Tinto selected the Atlas Copco mobile miner machine as one of the concepts to proceed with for construction of horizontal infrastructure for access and footprint. In addition to un-derground drilling and hauling equipment, Atlas Copco?s Robbins mobile miner concept (a previous attempt at horizontal mechanical excavation) completed trials at Mount Isa, Pasminco and Taisei. Rio Tinto selected the new Atlas Copco mobile miner machine concept for a number of reasons including the use of proven technology from the three previous mobile miner machines and other commercial products, as well as the ability to install complete ground support typical with high rock stress conditions at approximately 1,500 to 2,000 m (4,900 to 6,500 ft) depth. Atlas Copco, with support from Rowa, the Swiss company that specializes in back up systems for tunnel boring machines (TBM), is advancing the detail design of the access version of a tunneling system on behalf of Rio Tinto. Because of the different requirements between an excavation system for access tunnels and that for tunnels on the footprint, two different versions of the mobile miner machine technology were envisioned. The access and the footprint versions of the Atlas Copco mobile miner machine share a majority of key technologies and systems. Therefore, it was possible to conduct a performance conformation test using a full-scale version of the access machine that would also mitigate the technical risks for the footprint version. To alleviate confusion, this article focuses on the access version of the Atlas

Jul 1, 2010

By J. J. Scott

As a Rock Mechanics investigator, the author has, Over his career, attempted to use his best knowledge in developing better rock control fixtures. Based on the experience of nine years of development of friction rock stabilizers, in 1980 he decided to launch a new investigation to develop a unique roof support fixture which would fit the coal mining market. The largest single user of roof bolts in the world is the American coal mining industry, historically using up to 100 million fixtures per year. In 1989 they used approximately 82 million fixtures.

Jan 1, 1990

By Irwan Halim, Young Jin Park

A new tunnel lining was designed for rehabilitation of the existing unlined Weehawken Tunnel in New Jersey. Structural assessment using beam spring models was performed for the lining design as a drained structure at the invert with a waterproofing umbrella. Empirical Federal Highway Administration (FHWA) guideline was typically adopted for estimating hydrostatic pressure, which recommends full hydrostatic pressure at the crown and ten or twenty-five percent gradual reduction from the initial pressure toward the invert. Finite element seepage analyses were conducted for the actual conditions based on anticipated drainage behind the lining and impact on the structural design. Considerations will be provided on the existing guideline for estimating hydrostatic pressures.

Dec 1, 2022

By M. A. Reinsel

New technology for removal of nitrate from low-temperature waters has been developed. Typical results from the first operational-scale system (operating at a metal mine in Montana since January 1996) are over 90 percent nitrate removal at a flow rate of 130 gpm and a water temperature of 12°C. The system also operated successfully at flow rates as high as 300 gpm and water temperatures as low as 2°C. The ABC is advantageous because it is: a) cost-effective to design, construct and operate, and b) effective at cold water temperatures. The system can be designed for a variety of flows, nitrate concentrations, water temperatures and water qualities.

Jan 1, 1998

By James M. Griffin

It was not many years ago that people would have argued that a coal session did not belong at an International Mining Convention. Historically, steam coal has always been used domestically due to its natural geographic diversity and high transportation expense. Times have changed. With the help of Opec, steam coal has gone international. As opposed to metallurgical coal, whose trade routes have a long history, whose supply sources are more limited and whose market growth is seen by most to be relatively flat, steam coal export forecasts are calling for more than a doubling by 1990 and a quadrupling by the year 2000. Suddenly, one must be familiar with coal mining on a global basis in order to predict which regions will be able to fill these markets.

Jan 1, 1982

By M. J. Hannan

Considerable interest has arisen in developing analytical methods suitable for measuring resource commodity substitution patterns. some of this work has applied the Translog method to estimate actual elasticities of substitution. Recent examples incl.uae Privolos and Dunietz (1987), Kopp and Smith (1983), and Moroney and Trapani (1983). Another method, one which has received attention earlier in the work of Fisher and Pry (1970), is that of the logistic or diffusion function. We believe that the latter method has properties suitable for analyzing current problems of material substitution. The present study thus evaluates this method in its original logistic form as well as an extended version incorporating additional explanatory influences. The analysis is applied to copper/aluminum substitution and iron ore beneficiation. Substitution for copper by aluminum is examined in the building wire and cable, and magnet wire end-use markets. For iron ore, the substitution of pellets for sinter is considered for the U. S. market.

Jan 1, 1990

By J. Drelich

The wetting behavior of liquid polymers at solid surfaces and the adhesion forces involved at polymer-filler interfaces should always be considered in the fabrication of high quality polymer composites, including those made with mineral fillers. Spontaneous polymer spreading over the filler surface is a basic condition in the fabrication of the polymer-mineral composites. In this regard, the wetting and adhesion characteristics of polymer-mineral systems are reviewed in this contribution. It appears that several aspects of wetting phenomena at mineral filler surfaces are not well described in the literature and require further systematic study. Specifically, it is clear from this review that efforts should be made to determine the effects of mineral surface contamination (including surface hydration) on wetting and adhesion phenomena, and to determine the wetting characteristics of molten polymers at mineral filler surfaces. It is expected that any improved fundamental understanding of wetting and adhesion phenomena for the polymer-mineral composites will provide the basis for further technological development.

Jan 1, 1995

By M. Moats, I. E. Paschalidou, K. Awuah-Offei

Tellurium (Te) is a rare metalloid that is predominantly produced from the treatment of anode slimes formed during copper (Cu) electrolytic refining. The US Government lists Te as one of the 50 critical minerals, partly, because of its use in thin-film photovoltaic (PV) technology. Given policy initiatives to increase Te production, it is important to evaluate the life-cycle environmental impacts of Te recovery as a by-product of Cu processing. The literature contains a few specific life cycle assessment (LCA) studies of groups of metals that include Te without proper regard to impacts per life-cycle stage of Te production or the effect of allocation on the results. This study builds an LCA model of the production system of Te from anode slimes treatment to evaluate the effect of allocation on life-cycle impacts. We build life cycle inventories using data from the Ecoinvent v3.7.1 database, literature, and engineering calculations and allocate impacts in proportion to products’ mass and economic value. The results show that economic value-based allocation yields greater impacts than mass-based allocation indicating the significant effect of the allocation approach on life-cycle impact estimates.

Feb 1, 2023

By William E. Robinson

Why did it fail? My first reaction when assigned this topic was to say: because somebody "goofed"--then thank you all for letting me say those few words, then promptly sit down. All of you have been bandying this problem around for many years--so all of a sudden I should come up with the solution. Well, While I might not provide you with your particular answer, I think I can show you some of the resolutions to it. Somewhere along your path of experience you may have discovered that a good formula for starting a fight is to tell a group of dedicated (Nordberg Crusher) users they should be using (Allis-Chalmers), or a group of (Allis-Chalmers) 'users they should be a (Traylor). Now, if you really want a melee, get both groups together and tell them they should be using a (Stedman Cage Mill). This is one sure way you can learn how great minds arrive at logical, well thought-out conclusions, based on all the relevant facts. Why did it fail? I could go on for hours giving you specific reasons why. One of my engineering professors used to start his new class off each year by writing on the blackboard--four and two, then turn to the class and ask: What is the problem? One brave scholar would venture to answer 8. His head would shake no. Another would dare 6. Again, a head shake. Now that the ball had gotten rolling, a number would vocally decide it had to be two, which produced only another shake of the head--no. All of them had missed the question he had asked : What is the problem? What he had gotten ,were some of the possible answers to the problem.

Jan 1, 1977

By L. R. Chirinos

The Tintaya mine of BHP Copper, located in Southern Peru, includes a copper oxide deposit hosted in a mineralized skarn zone. The ore contains large amounts of clays and high acid consuming species resulting in low heap leaching performance. A treatment scheme was proposed that included a wet screening separation. The coarse fraction would be treated by heap and the fines by agitation leaching. The dissolved copper would then be recovered through solvent extraction and electrowinning (SXEW). Testwork determined the optimum heap leaching conditions to treat the oxide in on/off pads of 3 meter height with an initial acid cure followed by variable acid strength during irrigation. The method resulted in a reduced acid consumption and good copper recoveries.

Jan 1, 1997