Search Documents

By A. Halim, A. Martikainen, S. GYAMFI

This paper outlines a unique case of the development of strategies to reduce ventilation and heating costs in Konsuln iron ore mine in northern Sweden. The mine, located just south of Luossavaara-Kiirunavaara Aktiebolag’s Kiruna iron ore mine, was developed as a test mine from 2018-2020 for the Sustainable Underground Mining (SUM) project. Besides functioning as a test mine, Konsuln also contributes to ore production. The existing mine ventilation system was designed for the current production rate of 0.8 million tons per annum (Mtpa). There is a plan to increase this rate to between 1.8 and 2.0 Mtpa.

Sep 30, 2021

By Morgan M. Sears, Mark Morris, Joseph Bright

In an effort to advance the science underlying modern coal pillar stability analysis, researchers at the National Institute for Occupational Safety and Health are currently involved in research aimed at better understanding the impact of an in-seam rock parting on the strength of coal pillars. The purpose of this study is to determine a suitable virtual mining height that could be applied using current pillar stability analysis tools. To accomplish this, the boundary element model LaModel was used to back analyze data collected on pillar performance in a room-and-pillar panel at the Maple Eagle Mine located in Southern West Virginia. In a previous work, data collected from borehole pressure cells (BPCs) and extensometers were taken from three instrumentation sites. Data collected from the back bleeders were used to measure the rear abutment stresses, and data collected from two instrumentation sites in the wraparound bleeder were used to measure the front and side abutment stresses as well as the peak strength and performance of the slabbed leave pillar. The utilization of two nearly identical instrumentation sites in the wrap-around bleeder provided much needed repeatability of the obtained measurements. In this study, the data collected from BPCs at the three instrumentation sites was calibrated to match the Bieniawski pillar stress gradient. To model the measured pillar behavior, the LaModel program was selected due to its capability of being directly comparable to the Analysis of Retreat Mining Pillar Stability (ARMPS) and Analysis of Coal Pillar Stability (ACPS) programs. The model was then calibrated to match the measured abutment extent and abutment stress. Finally, the model was validated by reducing the modeled mining height until the yielding of the slabbed leave pillars in the model matched what was measured in the field. The final calibrated mining heights show that a reduction of the shale parting thickness, not including any clay layers, of 52% is applicable. This research study provides the first known measurement of the ARMPS/ACPS “50% Rule” and its applicability to this panel of the Maple Eagle Mine. This finding provides a proof of concept and could have significant implications for future research.

Feb 1, 2024

By J. P. Ducarme, J. L. Carr, C. C. Jobes

"An average of 1.2 fatalities occur per year in underground coal mines in the United States when a miner is struck or pinned by a remote-controlled continuous mining machine. Proximity detection technology provides a means to prevent these types of accidents by disabling all machine motion when a miner is in close proximity. Researchers at the National Institute for Occupational Safety and Health (NIOSH) have developed the intelligent Proximity Detection (iPD) system, which continuously tracks the position of miners near the machine and disables only those machine motions that could cause a pinning accident. This system, previously demonstrated using non-permissible proximity detection hardware, has now been shown to be effective when implemented using an MSHA-approved system as a platform. Performance tests have shown accuracy, repeatability, and stop zone identification to be comparable to or better than the system demonstrated with non-permissible hardware. INTRODUCTION Underground coal mining room-and-pillar operations typically use Continuous Mining Machines (CMMs), such as the one shown in Figure 1. When CMMs first became available, they were operated from an on-board operator’s compartment that protected operators from roof falls and other hazards but severely restricted visibility and subjected them to machine vibration and high levels of dust and noise. To solve these problems, remote controls were developed to operate CMMs. Now CMM operators are free to position themselves for best visibility of each mining task and are no longer subjected to the rough motion of the CMM during mining operations or the dust and noise generated by the machine. However, this technological advance removed operators from the protection afforded by the operator’s compartment and exposed them to the hazard of being struck or pinned by the CMM or other large moving machines."

Jan 1, 2015

By S. Mischler, J. Organiscak, S. Klima, C. Seaman

"Researchers at the National Institute for Occupational Safety and Health’s Pittsburgh Mining Research Division (PMRD) performed comparative testing of six hollow cone water sprays from three manufacturers: static swirl chamber sprays from Spraying Systems (BD-3, BD-5) and Steinen-Hahn (SH-3, SH-5), and movable swirl chamber sprays from Repair King (RK-3, RK-5). Water flow testing was completed at three operating pressures (60, 80, and 100 psig) where both sets of sprays (3-series and 5-series) produced similar water flows, deviating less than 8% from the average water flow rate at each pressure. Airflow induction testing was completed at 80 psig using a hot wire anemometer to take air velocity measurements upstream of the spray nozzles. Respirable dust capture efficiency testing was completed in a 14.5-m3 (512-ft3) closed system dust chamber at 80 psig. The dust capture efficiency ranged from 7.2% to 9.9% for the 3-series nozzles, and from 5.3% to 7.1% for the 5-series nozzles. Sprays were also analyzed using a Cloud Aerosol and Precipitation Spectrometer (CAPS), which uses light scattering to count and size the airborne water droplets from each spray. In both cases, Spraying Systems sprays produced the largest mean droplet size, followed by Steinen-Hahn and Repair King sprays, respectively. INTRODUCTION Coal mine worker overexposure to respirable coal dust continues to be a problem in underground coal mining operations in the United States. The U.S. Mine Safety and Health Administration (MSHA) now requires coal mine worker respirable dust exposure to be no more than 1.5 mg/m3 average over the actual working shift (CFR 30-70.100, 2016). Potential overexposure to respirable dust by continuous miner, roof bolter, and shuttle car operators may be prevented if proper safety and health practices are implemented as detailed in the mine’s ventilation plan (CFR 30-75.371, 2016). Water sprays are a necessary component of an underground coal mine ventilation plan. They are important on the continuous mining unit for moving air and removing respirable coal dust from the breathable airstream. MSHA requires underground coal mines to include the number, types, location, orientation, operating pressure, and flow rate of operating water sprays in their mine ventilation plans (CFR 30-75.371, 2016). Water sprays can become clogged, requiring the sprays to be properly checked, maintained, and replaced in order to continue meeting the ventilation requirements described in the mine ventilation plan.In an effort to eliminate the problems with spray clogging, Repair King has developed self-cleaning movable swirl chamber hollow cone water sprays (RK-3, RK-5). The spray’s movable swirl chamber is designed to only open when water pressure is applied to the spray nozzle, preventing the nozzle from clogging. Anti-clogging sprays could improve mine production by reducing the amount of time spent servicing clogged sprays. Also, these sprays could improve health and safety of miners since they would continue to suppress and capture dust and continue to move airflow at the face, while a clogged spray loses this ability until it is cleaned or replaced manually. The objective of this research was to assess the comparability of the Repair King sprays with the most commonly used sprays in underground coal mines using performance criteria. An assessment of the sprays self-cleaning or anti-clogging capability was not conducted."

Jan 1, 2017

By Michael J. Beus, Jan G. Patricio

INTRODUCTION The U.S. Bureau of Mines, Spokane Mining Research Center, has been conducting and documenting rock mechanics research in the Coeur d’Alene mining district for the past ten years (1, 2, 3, 4, 14, 15). A current project combines the information gathered from rock mechanics instrumentation, geologic structure, and analytic techniques to improve shaft and support design for the deep mines of the district (3). This project required knowledge of the anticipated loads and the physical properties of the rock mass to provide accurate input data for computer design models. Several techniques have been utilized to determine the physical parameters including the USGS (U.S. Geological Survey) solid inclusion probe, the CSIR (Council for Scientific and Industrial Research) biaxial and triaxial strain cells, and the CSM (Colorado School of Mines) dilatometer. This paper describes the determination of the in situ modulus of deformation in three mines over a period of three years and the evaluation of these results as they applied to this project. The need for in-situ rock mass properties such as the modulus of deformation has stimulated research and development of a large number of instrumentation techniques. One area of continuing interest involves various methods of radial borehole dilation. This concept was pursued by Menard (9) with an apparatus known as the pressure meter, which is used frequently in soil mechanics. Other developments in rock mechanics include the CPC (cylindrical pressure cell) by Panek (11) and the dilatometer by Rocha et.al. (13) in Portugal. The CSM dilatometer, which also utilizes this technique, was chosen for this project because it required a small amount of background study, was inexpensive, and could easily be combined with other experiments being planned for the test locations. Although no previous field applications to hard rock (compressive strengths greater than 20,000 psi) has been documented, the instrument was selected since good results have been achieved in granite, oil shale, and several coal measure rocks (11, 12).

Jan 1, 1977

By Yuting Xue, Gamal Rashed, Zoheir Khademian, Connor Brown, Khaled Mohamed

Ground falls in U.S. underground coal mines can lead to significant consequences, including loss of life, injuries, damaged equipment, and production stoppage. Improving the safety of the workplace is of utmost importance for mine workers and the U.S. economy. The Mine Safety and Health Administration (MSHA) accident/injury/illness dataset provides short narratives for reported incidents, including ground-falls. The main objective of this study is to develop a framework that includes: 1) utilizing machine learning algorithms to categorize ground-fall incidents from narratives based on the main cause of the occurrence and 2) demonstrating an example of a user-friendly visualization to display injury/fatality trends from narratives in U.S. coal mines between 1983 and 2021. The developed framework was tested on a subset of the data and achieved an average F1-score of 96% in categorizing the incidents. The outcome will help identify areas requiring additional research and innovative solutions to reduce severe occupational hazards.

Feb 1, 2024

By M. G. Vieira

This investigation addressed the possibility of producing pellet feed at a silica content of = 1.0% using a representative sample of Samarco´s mechanical flotation tailings. This sample contained 11.0% Fe and presented an F80 = 116 µm and a d50 = 63 µm. The higher silica content was verified in the coarser fractions and the higher iron content in the fraction -37 µm. Specular hematite is the most abundant mineralogical phase in the fraction -37 µm. The technological tests used one of four methods: magnetic concentration using a wet high-intensity magnetic separator, magnetic concentration using a SLon high-gradient magnetic separator, reverse flotation or direct flotation. The methods using the magnetic concentrator SLon, reverse flotation and direct flotation did not present results meeting the target of the study: iron content in the concentrate (rougher stage) greater than 34% or iron recovery greater than 80%. Cleaner stages were not achievable with the resulting concentrates. In contrast, the most successful method consisted of using wet high-intensity magnetic separators (WHIMS) as a rougher stage and reverse flotation as a cleaner stage. Using this route, it was possible to produce a pellet feed with a silica grade of 1.0% and high specular hematite content.

Jan 1, 2010

By A. G. Mayton, D. H. Ambrose, C. C. Jobes, N. K. Kittusamy

In a systematic study, the National Institute for Occupational Safety and Health (NIOSH) evaluated seat designs in low- and mid-seam shuttle cars during production operations at two underground coal mines in southern West Virginia. The purpose was to support, with additional data, earlier findings that NIOSH ergonomic seat designs (featuring viscoelastic foam padding and lower-back support) may help reduce health risks to operators of coal mine shuttle cars. Eight shuttle car operators evaluated seven seat designs (one already in use in each vehicle and five NIOSH designs) relative to perceived and measured whole-body vibration (WBV) exposure (including vehicle jarring/jolting) and discomfort. Operators’ perceptions using a visual analog scale (VAS) and questionnaire ratings were compared with International Standards Organization (ISO) 2631-1:1985 fatigue-decreased proficiency (FDP) limits and measured WBV levels on low- and mid-seam shuttle cars. Objective and subjective data results indicated that NIOSH seat designs (with added adjustability, lower-back support and improved seat padding) performed better to reduce vehicle jarring/jolting levels and that shuttle car operators favored them over existing seat designs. The NIOSH low- and mid-seam shuttle car seats showed 45 to 77 percent better performance in FDP and 9 to 60 percent better performance overall in operators’ ratings. Considering the VAS results for low- and mid-seam shuttle cars under no-load conditions, operators rated the level of jarring/jolting 18 to 89 percent lower with the NIOSH seats. Reductions in measured vehicle jarring/jolting were 19 to 46 percent for the three-directional vector sum accelerations relative to the existing seats on the low- and mid-seam shuttle cars. Questionnaire responses indicated that operators for both shuttle car models rated NIOSH seat designs as more comfortable overall. Vehicle operators most frequently suggested adding armrests to improve the seats on the mid-seam shuttle car. A suggested improvement for the low-seam shuttle car was to make the seat a better fit for the operator compartment, which would enhance clearance between the operator and vehicle controls and allow for better seat adjustment and operator visibility.

Jan 1, 2009

By M. H. Morcali

Pistachio nut shells, an agricultural waste biomass, and Lewatit TP 214, a commercial sorbent, were investigated as adsorbents for the adsorption of platinum from dilute hexachloroplatinic acid solutions. Before the pistachio nut shells were carbonized, adsorption percentage was 65%, whereas Lewatit TP 214 ensured almost 100% adsorption. However, after the pistachio nut shell was carbonized at 1,000° C under an argon atmosphere, the platinum adsorption (%) increased two-fold. The effects of such parameters as sorbent dosage, contact time, temperature and solution pH on adsorption were studied in detail in batch mode. The adsorption equilibrium data were best fitted with the Langmuir isotherm model. The maximum adsorption capacities, Qmax, at 25° C were found to be 38.31 and 33.22 mg/g for the carbonized pistachio nut shell and Lewatit TP 214, respectively. The adsorption of platinum on both sorbents was found to be described by the pseudo-second-order kinetic model. The results indicated that the activated carbon prepared from pistachio nut shells can be effectively used for the removal of platinum from acidic solutions.

By Robert D. Thomson

The plastics industry runs into the billions, both in the dollar value of its finished, products and in the pounds of plastic raw material produced. It is, too, one of the fastest growing industries with a 300 percent increase in production in the past ten years. Informed estimates set 5.9 billions pounds as the plastic volume for 1959. Statistically, this is equivalent to a per capita consumption of 25 pounds in the United States. Plastics are man-made materials in contrast to natural materials like wood and are a family of materials -- not a single material - each member having special advantages. A generally accepted definition; for plastics is; a large and varied group of materials which consist, wholly or in part, of combinations of carbon with oxygen, hydrogen, nitrogen, and other organic and inorganic elements. This, while solid in the finished state, at some stage in its manufacture is soft enough to be formed into various shapes, most usually through the application either singly or together of heat and pressure. Many combinations and many different materials are thus possible. Therefore, for purposes of simplification, most plastics can be classified under one of 14 recognized basic family groups. These groups in turn generally can be further classified into one of two major subdivisions - thermosetting or thermoplastics. A few plastics are in between and they can be formulated to be either thermosetting or thermoplastic.

Jan 1, 1960

By M. N. Chandraprabha

This paper discusses the role of the mineral-adapted acidiphilic microorganism Acidithiobacillus ferrooxidans in the beneficiation of arsenopyrite-containing multisulfides (pyrite and chalcopyrite) and the bioremediation of the resulting arsenical waste water. It was found that adaptation to minerals alters the surface properties of the microorganism. Bacterial adaptation to arsenopyrite and controlled bacterial adhesion to mineral surfaces lead to selectivity in arsenopyrite separation. Bioremoval of arsenic ions (both arsenite and arsenate ions) by Acidithiobacillus ferrooxidans is also discussed. Key words: Acidithiobacillus ferrooxidans, Bioremediation, Arsenopyrite beneficiation

Jan 1, 2009

By I. R. M. Chaston

Abstract. This paper puts forward the concept of 'radial' plant layout where all crushing, milling and treatment operations are preferably concentrated in one central area and these separate stages are connected by radiating conveyors to and from outside storage areas. This system is contrasted to the more customary system of 'linear' plant layout where the crushing, milling and often the treatment operations follow one after the other in separate buildings. The radial system simplifies and improves contral and supervision to a very considerable extent and can lead to a form of continuous plant operation with the separate sectors shutting down in succession for necessary maintenance while maintaining the overall plant operation. The paper is illustrated with example: from past and recent diamond treatment plant practice in South Africa which demonstrate the reduction in plant labour achieved by this system. Previous objection to this type of layout on the grounds that it inhibited plant expansion are shown to be unwarranted. Radial Layout for Increased Treatment Plant Productivity A great deal of time and trouble is spent by highly qualified and experience( metallurgists in developing the right treatment process for a given ore. This process is then often expressed in a treatment flowsheet of the type shown in Fig. 1 which shows a typical diamond plant. This flowsheet, when completed, is commonly handed over to the mechanical engineers who then design the layout of the equipment indicated on the flowsheet and produce the working drawings upon which the detailed construction of the treatment plant will be based. It is an unfortunate fact that the tedious and time-consuming juggling of equipment and inter-plant transportation is often left to hard-working draughtsmen who, however capable' in their field, lack practical experience in the day-to-day operation and maintenance of the treatment plants they design. As a result many plants have been produced which, while they satisfy the requirements of the flowsheet with minimum capital requirements, cost far more than should be necessary to op¬erate and maintain. It is often possible to change individual items of equipment which do not achieve the performance required of them, but it is usually extremely expensive to change the basic layout of the plant if this should be found to be unsatisfactory. It should therefore be recognised that great care and attention should be spent on consideration of the basic layout of any treatment plant and that the views of both designers and operators should be fully regarded before settling upon the inevitable compromise dictated by the varying requirements of process-engineering and economics. It is unfortunate that this important subject receives such scant regard in the standard ore dressing text books and hand-books, being usually dismissed in a few paragraphs.

Jan 1, 1977

Gangue-cemented paste backfill (GCPB), is a well-established green mining technology and significantly improves the recovery rate of mineral resources, prevents mine dynamic disasters, reduces surface subsidence, and consumes a considerable amount of solid waste. The addition of an early strength agent as an additive in cement-based materials provides several security, technical, and economic advantages. In this study, the early strength agent on the early age (3, 7 and 28 days) strength of GCPB is evaluated experimentally. The GCPB specimens have an initial sodium sulfate early strength agent concentration of 0%, 1%, 2%, 3%, and 4%, and the obtained samples were analyzed by testing for uniaxial compressive strength (UCS) and scanning electron microscopy (SEM). The test results show that the UCS of the GCPB specimens with sodium sulfate is much higher than that of the blank specimens. When cured for 3 days and 7 days, the strength of GCPB with 2% sodium sulfate increased the most, by 131% and 116% respectively. When cured for 28 days, the strength of GCPB with 1% sodium sulfate increased by 135%. Scanning electron microscopy (SEM) results showed that the GCPB with 1% and 2% sodium sulfate had better internal structure compactness, thicker acicular crystals, and more flocs. As a kind of early strength agent, sodium sulfate can react with calcium hydroxide to generate calcium dihydrate sulfate and then react with calcium aluminate; the hydration product (C3A) quickly generates calcium sulfoaluminate hydrate (AFt) needle-shaped crystals, forming an early skeleton and improving the early strength.

Jan 7, 2020

By Nick Karlin

Dragados USA is constructing the LA Effluent Outfall Tunnel, a 7-mile, 18 ft internal diameter effluent discharge tunnel, utilizing a 21.6 ft (6.585 m) Herrenknecht Mixshield TBM. This paper highlights the means and methods used for TBM launch from a 55 ft diameter shaft excavated in wet with diaphragm wall support of excavation. This included SEM excavation of jet grout blocks for starter and tail tunnels, temporary concrete structures and steel installations, TBM sealing system, umbilical management for TBM hydraulic, electric and bentonite circuits as well as complex segment delivery logistics. The many launching challenges were overcome thanks to the innovative approaches from the project team.

Jun 13, 2023

By Roger Nendick

The recent developments in refractory precious metal ore processing (Bio-oxidation, Autoclaving), and the revitalization of the more traditional roasting processes have attracted great attention in recent years and are indeed the focus of todays symposium. It must always be remembered, however, that the term refractory ore by definition means that the material 'must be capable of being treated at a profit". Given the high cost of the refractory processes, the requirement to be treated at a profit requires very close scrutiny during the evaluation phase of the property development. The M.G.M. film company has the latin motto Ars Gratia Artis meaning Art for Arts Sake. Ingeniatore Gratia Ingeniatoris (a very crude attempt at saying Engineering for Engineerings Sake) should not be the motto for mining companies intent on exploiting refractory gold deposits, but rather the wittily tilted heading for this paper "Take the money and run like a thief". The following hypothetical case studies show that the high technology solution is not always the best financial solution.

Jan 1, 1990

By Stephen G. Hardcastle

3D-CANVENT is a software package that integrates advanced computer aided design (ACRD) true 3D graphics with a mine ventilation simulator. The package runs as a Windows(tm) application to access its printer drivers environment and does not need third party CAD software. It is composed of two primary modules: DMVENT and MINEDESIGNER. DMVENT is a traditional Fortran coded Hardy-Cross iterative ventilation network solver written in 1980 with thermodynamic capabilities. This module is relatively unchanged with the traditional data input options for branch type, specified or calculated resistances, fixed flows, and fixed or variable pressure fans. MINEDESIGNER is the graphics engine that optimizes the ventilation design process. It performs the front-end transformation of input data entered in the graphical interface into the correct format for the solver. At the back-end it reconverts the historically standard tabular data output from the solver into an easily viewed graphical format. ACRD features of MINEDESIGNER are used to generate a 3D wire-frame node and branch network of the mine's ventilation system. The network can be displayed in up to 4 views orientated to XYZ planes or a 3D view. All the views have zoom, pan, slice and rotate options. The graphical interface efficiently permits data entry and editing via a mouse with pick-and-point item selection. Branches can be found or added with "search" and "join" options. Visual interpretation is enhanced by the 16 colour options for branches and numerous graphical attributes. Network locations are readily identified by alpha-numeric names for branches, junctions and fans, and also the logical numbering of junctions. The program is also readily expandable for pollutant simulation and control/monitoring applications.

Jan 1, 1995

By Yves Boissonnas, Marco Bettelini

"INTRODUCTION AND OBJECTIVES The operational safety of long and very long rail tunnels represents a key issue in all development stages, including design, construction, commissioning and operation. The spectrum of potential threats is very broad and challenging. These issues can only be mastered by means of a proper combination of a number of safety measures at various levels. This paper focuses on the specific safety issues and the extremely challenging conditions characterizing very long and deep tunnels. They include a significantly increased risk during operation that the incident train cannot exit the tunnel by its own means, long self-rescue and rescue distances, the presence of a number of trains, possibly mixed traffic as well as significant thermal issues. Amberg Engineering is strongly involved in the design and construction of most long and very long rail tunnels in Europe, including in particular the Gotthard Base Tunnel (GBT), Lyon-Turin Base Tunnel (LTF) and the Brenner Base Tunnel (BBT). The combined experience arising from these tunnels forms an invaluable body of expertise, which is summarized in this paper. The focus is on shared issues with practical relevant examples and project-specific solutions. Special attention will be devoted to the 57 km long Gotthard Base Tunnel, which will be operational by mid-2016 and will be the longest infrastructure tunnel worldwide. VERY LONG TUNNELS IN EUROPE Overview From the point of view of safety, tunnels in excess of about 20 km exhibit a significantly increased risk that incident trains could stop within the tunnel. This is related to the European Technical Specifications for Interoperability (TSI) on rolling stock, to be discussed in the chapter on rescue stations. This paper will specifically focus on the following longest tunnels in construction or operation, listed in Table 1."

Jan 1, 2016

By T. Ritzel

Predictive maintenance technologies including vibration analysis, tribology, infrared thermography, ultrasonic detection, and electrical measurements have been applied to large electric mining shovels at Cyprus Sierrita. The predictive program was initiated by Cyprus Sierrita and P&H Mining Equipment at the Cyprus Sierrita Mine in Tucson, Arizona during August of 1996 on the P&H model 2300 and 4100 electric shovels. The utilization of these technologies has shown the potential for improving electric mining shovel availability and minimizing maintenance costs. Predictive technologies provide the tools to assess machinery condition. Availability is enhanced by the condition based planning of component replacement. Maintenance costs are minimized by focusing resources through condition based prioritization.

Jan 1, 1997

By III Scotland

Genstar's underground mine at Texas, MD experienced a failure of the mine roof and subsequent damage to an underground backfill caused by surface floodwaters. A hydraulic backfilling program was developed in house to stabilize temporary repairs to the mine roof, replace 2300 yards of pneumatically stowed backfill, and complete a permanent repair to the mine roof. A flowable backfill material was developed, tested, and later marketed as the result of experience gained during this project. In addition, Genstar personnel developed backfilling techniques to meet the requirements of the repairs and completed work without the additional expense of non company services or contractors.

Jan 1, 1992

By John C. Bowling

Many recent mine developments in North America are located in remote northern regions with extreme winter temperatures in the range of -20oF to -60°F. In addition, many locations are subject to very heavy snowfall. This paper discusses some of the key considerations in the planning and design of mine plant buildings, particularly concentrators, located in these regions. SUMMARY & CONCLUSIONS The subject is considered under three main headings: I. Building Out line and Structural Frame 2. Wall and Roof Materials 3. Foundations The plan outline of a mine plant building will naturally be governed by the scope and layout of the process equipment it contains. The selection of roof profile, on the other hand, will generally depend upon a number of factors extraneous to the process e.g. snow conditions. When these factors are considered for concentrators in cold locations, a flat or stepped roof will usually be more economical and suitable than a sloping roof. The materials normally used for the structural framework of concentrators are the same as used for other industrial buildings, namely steel, concrete and wood. Structural steel, however, is the most commonly used material for concentrators in

Jan 1, 1971