Search Documents

By A. Bieg, M. Samson, Z. Bell, A. Zinsser, J. Schuyler

As the world progresses toward the renewable energy transition, the demand for minerals increases exponentially. According to the International Energy Agency (IEA) 2021 Net Zero by 2050 Report, critical mineral production needs to grow six times to combat climate change. It’s estimated that four to seven percent of global greenhouse gas (GHG) emissions come from the mining sector’s Scope 1 and 2 (direct and indirect) emissions. Including Scope 3 (upstream, downstream, and embedded) emissions, the sector accounts for 28% of global GHG emissions. In a typical mining operation, diesel fuel is the biggest source of direct GHG emissions, and haulage is often the main source of diesel emissions. Large haul trucks have been the industry standard for over 50 years and offer flexibility, relatively low capital cost (especially with equipment lease options), and guaranteed technology with known maintenance. The challenge will be to justify their continued use when there are more economical options that lead to significant reductions in GHG emissions. The purpose of this study is to compare five haulage options in terms of GHG emissions, using the methodology defined by the Greenhouse Gas Protocol Scopes 1, 2, and 3 (Category 2). Additionally, this analysis compares operating and capital costs associated with the five haulage options (emerging and proven technologies): 1) Diesel-Electric Haul Trucks, 2) Battery-Electric Haul Trucks, 3) Fuel Cell Haul Trucks, 4) Railveyor, and 5) Conveyor. This analysis looks at the emissions and costs associated with operating the equipment (fuel and electricity), the embedded emissions and costs associated with the construction and installation of the equipment itself, and the associated infrastructure (roads, powerlines, and rail).

Feb 1, 2023

By W. W. Wen

Approximately 3 percent of the raw coal processed in U. S. Steel coal-preparation plants ultimately reports to slurry- tailing disposal. The usual disposal method is to pump the refuse slurry containing the minus-48 mesh (300 µm) refuse into dams or impoundments that are constructed of the coarse refuse. The failure of an impoundment at Buffalo Creek, Saunders, West Virginia and the sliding failure of a coarse refuse pile at Aberfan, Wales, England, resulted in an evaluation of refuse disposal methods by various regulatory agencies as well as coal producers. The result of this evaluation was the promulgation of Federal regulations dealing with the construction, operation, and final abandonment of coal refuse disposal areas. As a consequence of these regulations the use of the landfill/impoundment method of disposal became in some cases economically urlfeasible or technically impossible. U, S. Steel has studied a number of alternative methods of refuse disposal. During an investigation of mechanical dewatering with a pressure filter, Portland cement was added to the slurry to solidify the filter cake. Because of the success of the cement addition it was decided to study the stabilization of fine-coal-refuse slurry through use of cement-type additives.

Jan 1, 1979

By Ankit Jha, Javad Sattarvand, Aaron Young

Blockchains are one of the prominent disruptive technologies that are being implemented in several disciplines. The application of blockchains in the mining and mineral industry can provide utility for several processes especially when the industry is undertaking digital transformation. The governing principles of blockchain technology are applicable in undertaking transformation in several processes within the mining industry. This study investigates the applications of blockchain technology within the realms of the mining industry and identifies key areas of implementation. A systematic review of publications on academic platforms relating to blockchain technology in the mining industry did not retrieve a considerable number of articles. Consequently, a thorough review of white papers and articles authored by individuals on use cases within the mining industry is compiled and presented in this manuscript. This paper identifies all the potential areas within the mining industry where blockchains could provide value and improve processes through their implementation. The broad area of implementation of blockchains includes supply chain, traceability in spare parts, contract management, regulatory compliance, and cyber security.

Nov 23, 2023

By A. L. Miller, A. J. Chambers, P. R. Griffiths, D. A. Parks

"Diesel engines are one of the primary contributors to the presence of nano and ultrafine aerosols in ambient air and occupational environments. Exposure to diesel emissions has been shown to contribute to various adverse health outcomes of the pulmonary system and cardiovascular system. Currently diesel emissions in the workplace are monitored by way of collecting the aerosol onto filters, which are then sent to a lab for thermal-optical analysis using the NIOSH 5040 method, which measures elemental and organic carbon explicitly. This process can take days or even weeks, and workers can potentially be exposed to excessive levels of diesel particulate matter (DPM) before the problem is identified. To remedy this, researchers from the National Institute for Occupational Safety and Health (NIOSH) are seeking to develop a field-portable method for measuring elemental and organic carbon in DPM aerosols. In the current study, we investigated the use of Fourier transform mid-infrared (FT-IR) spectrometry, which lends itself more readily to implementation in a real-time system than do the thermal-optical analysis methods. We have demonstrated a method for measuring organic and elemental carbon in DPM for a broad range of organic carbon (OC) to elemental carbon (EC) ratios (from 50.3 to 0.8). The ability to handle a wide range of OC to EC ratios is critical given the evolving diesel technology. INTRODUCTION Respiratory illnesses are common in mining industry workers [1] and exposures to toxic aerosols such as DPM can result in serious respiratory illness [2]. Health studies show a correlation between workplace exposure to diesel exhaust and an increased risk of lung cancer [3-8]. The International Agency for Research on Cancer (IARC) has characterized diesel exhaust as a human carcinogen [9], and similar classifications have been made by the World Health Organization and the California Air Resource Board. A recent study [10] suggests that the risk of lung cancer is approximately three times greater for heavily exposed workers. When compared to other aerosols in the mine environment, the settling time of DPM is significantly longer than that of dust due to their small particle size (typically < 1 µm) [11]. Additionally, submicron particles (such as DPM) are deposited in the lungs much more efficiently than their larger counterparts such as dust [12]. Previous studies focusing on particle morphology [13] show that the largest mass contributor to lung disease in mining is elemental carbon, which provides a solid core onto which hydrocarbons are adsorbed. In accord with those findings the Mine Safety and Health Administration (MSHA) decided on submicron total carbon as a surrogate for monitoring diesel particulate matter in the mining environment."

Jan 1, 2018

By Kelly Sands

"Mitigation may be considered a hurdle when it comes to environmental permitting. For complex projects with site specific mitigation plans, the time to devise those plans and get them approved can be a long and costly endeavor. However, mitigation options are expanding and the mitigation banking industry has grown tremendously over the last two decades, helping projects move forward with less debate. Mining companies are recognizing the value that mitigation banks provide in helping to shore up project timelines and costs. Where possible, companies are taking advantage of the opportunities to buy credits from thirdparty providers offering mitigation bank credits. In some instances, mining companies are taking matters into their own hands by establishing mitigation banks to realize their own mitigation freedom. That can have its advantages and disadvantages, as discussed below. All in all, the expansion of mitigation options has streamlined the permitting process, introduced flexibility, improved project permitting timelines and loosened the permitting girdle.Compensatory mitigationCompensatory mitigation involves actions taken to offset unavoidable adverse impacts to wetlands, streams and other aquatic resources and authorized by Clean Water Act section 404 permits and other permits. As such, compensatory mitigation is a critical tool in helping the federal government meet the longstanding national goal of ‘‘no net loss’’ of Waters of the U.S., both in acreage and function.Section 314 of the National Defense Authorization Act for Fiscal Year 2004 required the Secretary of the Army, acting through the Chief of Engineers, to issue regulations “establishing performance standards and criteria for the use, consistent with Section 404 of the Clean Water Act, of on-site, offsite, and in-lieu fee mitigation and mitigation banking.” The provision also required that those regulations ‘‘maximize available credits and opportunities for mitigation, provide flexibility for regional variations in wetland conditions, functions and values, and apply equivalent standards and criteria to each type of compensatory mitigation’’ (73 FR 19595). The result was the Final Rule on Compensatory Mitigation for Losses of Aquatic Resources issued in 2008 (33 CFR Parts 325 and 332).”"

Jan 6, 2017

By V. Montaruli, A. Nieto, M. Cardu

Nickel is a metal whose workability and mechanical strength at high temperatures and in corrosive environments makes it an indispensable alloying element for the realization of stainless steel, specialty steel, super-alloys, rechargeable batteries and electroplating. Because its main fields of application are key to the development of industry and, thus, to society, nickel has recently been recognized as a potentially critical mineral, despite its abundant reserves. The purpose of this paper is the creation of possible case scenarios determined by factors and events that, in the medium to long term, could change the current structure of the nickel market on the demand and/or the supply side. Four scenarios have been determined by considering a demand variation due to the occurrence of a natural disaster and an aerospace plan implementation and taking into account the resource nationalism and the skills shortage as supply varying factors. Through the creation of a georeferenced global nickel database, the paper proposes supply strategies related to the four scenarios for each top nickel consumer: China, India, European Union, United States and Japan.

Jan 1, 2013

By D. C. McLean

One of the few innovations in hydrometallurgy in recent years has been the utilization of the chemistry of basic iron sulfates called jarosites. These have been used to make iron-zinc separations in the processing of zinc concentrates and are a very important factor in both the Duval and Cymet copper chloride processes as a means of preventing iron build-up in the closed leaching circuits. Copper oxychlorides are kindred compounds in that they are insoluble basic salts that form at low pH (1.5 to 3) and precipitate selectively from many base metal solutions. They have been reported in the chemical literature as far back as 1860, and a few of them are known in their mineralogical forms (particularly atacamite) usually as nuisance minerals because of their chloride content. Several patents describe their synthesis and use as fungicides and insecticides, and papers have discussed their formation as corrosion pro¬ducts on copper and brass piping (14).

Jan 1, 1979

By Patrick Scott, Germán Schmeda, Morgan Mullins, Liam Knudsen, Bradley S. Van Gosen, Carma A. San Juan, Nicholas A. Karl, Jeffrey L. Mauk, Clayton Forbush

The objective of the US Geological Survey’s mineral deposit database project (USMIN) is to develop a comprehensive twentyfirst century geospatial database that is the authoritative source of the most important mines, mineral deposits, and mineral districts of the US. Since May 2017, the project has focused on critical minerals. Data for critical minerals that are produced as products are relatively robust, whereas data for critical minerals that may be recovered as byproducts are commonly of much poorer quality. Similarly, more is known about critical minerals that occur in conventional deposits than where those critical minerals occur in unconventional deposits. For example, rare earth elements occur principally in deposits hosted by alkaline igneous rocks, but there is potential for their production from phosphate rock mining, which is less documented. Lithium (Li) has been recovered from pegmatites and brines, but other Li-bearing deposit types have been delineated that may go into production. Cobalt may be produced as a byproduct or coproduct from a wide range ofmineral deposit types, whereas rheniumis a byproduct of copper ore. Significant opportunities for research exist that could help identify new sources of critical minerals, and may also help increase production and recovery from existing sources.

Feb 8, 2021

By NARAYAN K. BHAGAT, ARVIND K. MISHRA, C. Sawmliana, Rakesh Kumar Singh, Panchanan Hembram

Mining operations in close proximity to dwellings and sensitive structures present challenges in terms of mitigating the undesirable effects of blasting while maintaining productivity and ensuring the safety of surrounding communities. This paper explores the application of advanced blasting techniques, including the use of electronic detonators and the splitting of total explosive charges, to address these challenges. A series of experimental blasts were conducted, comparing blasts conducted with and without splitting of holes, to assess the impact on ground vibrations. The results demonstrated significant reductions in vibration magnitudes when implementing controlled blasting practices with splitting techniques. The findings highlight the importance of total explosive charge in determining ground vibration magnitudes within the danger zone of mine workings. The use of electronic detonators provided precise control over blast sequencing, contributing to safer and more efficient mining practices. These advanced blasting methods offer a practical and innovative solution for conducting safe mining operations near dwellings and sensitive structures, ensuring compliance with safety regulations while sustaining productivity.

Jan 23, 2024

By Kenneth N. Han

The effect of anions such as sulfate, chloride, and nitrate on the solubility of rare earth element-bearing phosphates and fluorocarbonates has been examined using relevant thermodynamic data. The study has found that these anions have significant influences on the overall dissolution of rare earth elements (REEs) from various sources in the aqueous media. The thermodynamic calculations in this study have indicated that the speciation of REEs with the anions tends to increase the overall solubility of the REE-bearing minerals. However, in some cases, strong precipitation of REEs with some of these anions causes an adverse effect on the solubility of these elements. It has been found that sulfate ion has the most pronounced effect on the solubility compared to nitrate and chloride, in which the latter two acids exhibited almost identical results. The calculated results have indicated that REE-oxide (hydrated) is the easiest compound to dissolve, followed by carbonate, phosphate, fluoride, sulfate, fluoro-carbonate, and oxalate in that order.

By Ritika Kundu, Moussa Wone, Amanda M. Morgan, Tatiana K. Proctor

The Piney Branch CSO 049 Storage Tunnel (PBST) will be the last major project for the DC Clean Rivers Program. The project includes construction of a 2,200-foot-long, 18-foot-internal-diameter storage tunnel; two connections to combined sewer infrastructure; and two shafts. Major challenges include excavation underneath an existing live outfall that must remain in service; excavation of the tunnel through several areas of low rock cover and mixed-face conditions; and negotiations with a variety of federal, regional, and local stakeholders to address project impacts. This paper describes the overall project scope; geotechnical conditions along the alignment; design and construction challenges; and construction procurement.

Jun 23, 2024

By Reginald E. Reid

Mining on Bureau of Land Management (BLM) administered lands is affected by Federal laws and regulations requiring the mining industry to plan for the environmental consequences of surface disturbance. Regardless of the requirements for obtaining a claim, permit, lease or contract to mine, a notice or a mining and reclamation plan will be submitted and an acceptable environmental document must be prepared prior to mining. A bond may be required based on the results of the environmental evaluation, public interest and the operator&apos;s past history of compliance. In several areas, Federal requirements are different from California&apos;s requirements under their Surface Mine and Reclamation Act (SMARA). Therefore, the BLM is negotiating with the State in order to work out problem areas of responsibility and duplication of effort.

Jan 1, 1984

By Alistair James, James Alcorn, Chaitan S. Sandhu, Andy Small

The Risk-Informed Decision Making (RIDM) working group is a group of industry professionals formed under the joint initiative undertaken by United States Society of Dams (USSD), Tailings Dam Safety Committee and Canadian Dam Associations (CDA) Mining Dam Safety Committee (MDC). The working group was organized to develop a guideline on implementation of a RIDM process relating to the design of mining water dams and Tailings Storage Facilities (TSF). Since its formation in 2022, the group has completed a literature review of more than one hundred (100) cross industry publications on applications of RIDM in mining water dams and TSFs, has held two industry workshops in Niagara Falls, Ontario in 2024 and Saskatoon, Saskatchewan in 2025 to capture industry input relating to the understanding and application of RIDM. The working group has subsequently formulated a process that constitutes good industry practice as it relates to application of RIDM in mining dams and TSFs. The authors, through their engagement and leadership in the working group and facilitating the two industry workshops in 2024 and 2025, are of the opinion that the successful application process of RIDM across Canada and United States (U.S.) is still not clear to many industry practitioners. There is confusion over terminology, good versus poor RIDM, and in some cases reluctance to use the RIDM terminology. This paper addresses critical knowledge gaps identified in the RIDM implementation for mining water dams and TSFs through three years of stakeholder engagement. It provides clarity of the process via a joint position statement and implementation roadmap, resolves terminology confusion, and documents contradicting industry opinions to promote adoption of good RIDM practices in Canada, U.S. and beyond.

Feb 22, 2026

By James W. Baxter

State geological surveys promote sound procedures for evaluation of mineral resources before development-procedures that protect the environment and accrue maximum benefit to citizens. Sophisticated laboratories have been equipped for geophysical, geochemical, petrographic, and mineralogic characterization of materials to assist citizens in land-use planning and optimum development of natural resources, activities clearly within purview of the state. Proper use of these facilities in support of exploration in a competitive, free-enterprise system should be based on achieving ultimate benefits to the public, but, in general, should not entail competition with commercial laboratories.

Jan 1, 1982

By E. McCullough

"Fostering positive community relations is a principal tenet of sustainable development, but conflict can test even the strongest of relationships. While conflict surrounding resource development projects has the potential to be destructive, it may actually pose opportunities for partnership and collaboration when managed effectively. It is therefore not only important for mineral resource professionals to recognize the financial and social costs associated with legal disputes among project stakeholders, but also for them to prioritize resolving social conflict using alternative channels that allow for win-win outcomes. A variety of dispute prevention and resolution techniques do exist, but successful practice is not yet the norm. Here we review the sources and consequences of social conflict in the context of mining projects, and discuss typical and alternative approaches to conflict management in light of their respective benefits and drawbacks. We also suggest implementation of conflict resolution lessons into resource-related university curricula as a critical step in the continued shift of the mining industry towards sustainable development. INTRODUCTION Social conflict is a recurring phenomenon in the human experience and serves as a critical mechanism for change [1-5]. It occurs when two or more parties perceive that their needs and interests are in direct competition with each other and believe they cannot be reasonably accommodated. Conflict over mineral resource activities, particularly the distribution of benefit and risk, has become an omnipresent issue throughout the world [6-7]. Contrary to common perception, however, conflict can be a positive, transformative encounter in some instances [2, 8-11]. For this to be possible, society and its acting agents must reconsider how to address conflict. What if conflict were only a challenge to try something different? It is well-understood that the mineral industries must manage an increasingly significant volume of social conflict [12-13], which can be a costly externality impacting all of whom are involved. Conflict is commonly considered in a two-party sense, but this can deeply over-simplify the true number of stakeholders. Besides mining companies and community members, government policymakers and regulators, public interest groups, and judicial systems, to name a few, bear the social expenses of poorly-managed conflict [4, 6, 12, 14-22]. It is desirable for interested parties to participate actively in a constructive way to pursue their needs rather than contributing to adversarial relationships, operational problems, and legal costs [1, 4, 12]. Some mining companies are of course already working to develop more productive relationships with their stakeholders, but there is undoubtedly still a gap between ideal and common practices. This gap can inhibit collaboration and threaten the potential for mutually-beneficial resolutions to complex social issues [12]."

Jan 1, 2016

By E. McCullough

"Fostering positive community relations is a principal tenet of sustainable development, but conflict can test even the strongest of relationships. While conflict surrounding resource development projects has the potential to be destructive, it may actually pose opportunities for partnership and collaboration when managed effectively. It is therefore not only important for mineral resource professionals to recognize the financial and social costs associated with legal disputes among project stakeholders, but also for them to prioritize resolving social conflict using alternative channels that allow for win-win outcomes. A variety of dispute prevention and resolution techniques do exist, but successful practice is not yet the norm. Here we review the sources and consequences of social conflict in the context of mining projects, and discuss typical and alternative approaches to conflict management in light of their respective benefits and drawbacks. We also suggest implementation of conflict resolution lessons into resource-related university curricula as a critical step in the continued shift of the mining industry towards sustainable development. INTRODUCTION Social conflict is a recurring phenomenon in the human experience and serves as a critical mechanism for change [1-5]. It occurs when two or more parties perceive that their needs and interests are in direct competition with each other and believe they cannot be reasonably accommodated. Conflict over mineral resource activities, particularly the distribution of benefit and risk, has become an omnipresent issue throughout the world [6-7]. Contrary to common perception, however, conflict can be a positive, transformative encounter in some instances [2, 8-11]. For this to be possible, society and its acting agents must reconsider how to address conflict. What if conflict were only a challenge to try something different? It is well-understood that the mineral industries must manage an increasingly significant volume of social conflict [12-13], which can be a costly externality impacting all of whom are involved. We commonly consider conflict in a two-party sense, but this deeply over-simplifies the true number of stakeholders. Besides mining companies and community members, government policymakers and regulators, public interest groups, and judicial systems, to name a few, bear the social expenses of poorly-managed conflict [4, 6, 12, 14-22]. It is desirable for interested parties to participate actively in a constructive way to pursue their needs rather than contributing to adversarial relationships, operational problems, and legal costs [1, 4, 12]. Some mining companies are of course already working to develop more productive relationships with their stakeholders, but there is undoubtedly still a gap between ideal and common practices. This gap can inhibit collaboration and threaten the potential for mutually-beneficial resolutions to complex social issues [12]."

Jan 1, 2016

By Zhiguo Chang, QINGXIANG CAI, Ebelia Manda, IZHAR MITHAL JISKANI, XIANG LU, Wei Zhou, Saleem Raza Chalgri

The concept of mine safety is highlighted in the literature of sustainable mining but not extensively discussed. This study analyzes various aspects of underground and surface mine safety and emphasizes its importance in the context of sustainable mining. More specifically, this research attempts to find the relationship between mine hazards and demographic characteristics, examine and compare the perceptual difference among miners, and determine the impact of mine hazards on workplace safety and safety climate. Descriptive analysis, chi-square test, independent samples t test, and linear regression modeling were conducted to achieve study objectives. Results confirmed that mine hazards were significantly associated with age and experience. Miners perceived lower levels of management safety practices, followed by supervisor safety, coworker safety, and job safety. The analysis showed that underground miners reported lower safety scores than surface miners. There was a statistically significant difference between miners’ perception of safety climate (p < 0.05). The results showed that the higher prevalence of mine hazards predicts poor workplace safety and a low safety climate. The regression models revealed that mine hazards have a significant effect on workplace safety (p < 0.05) and safety climate (p < 0.05). In conclusion, the distinctive model of mine safety presented here contributes to the monitoring and design of comprehensive safety interventions and helps to better understand how certain factors interact on multiple levels to influence the overall safety of the industry. In this study, some suggestions are put forward to provide directions to develop a sustainable mine safety system.

Mar 27, 2020

By Ronald L. Gibbs

IN THE BEGINNING Contrary to popular myth, the personal computer can trace its roots back to a time before 1981 and the IBM PC. The seeds of the personal computer revolution were probably founded in 1975 with the release of the Altair (kit) personal computer, first advertised in Popular Electronics. June of 1975 marked the beginning of the Homebrew Computer Club in San Francisco. The founding membership list of the Homebrew Club now reads like a "Who&apos;s Who" of those involved in the early development of the personal computer industry. The Apple I computer was created by Steve Wozniak in early 1976 from the newly manufactured MOS Technology 6502 chip. It had 4,000 bytes (4K) of Random Access Memory (RAM] memory, a revolutionary amount of memory in 1976. Another early pioneer, the Commodore Pet computer, was another 6502 machine, but with 8K of memory. Tandy Corporation made its name in the hobby industry with leather kits. They embarked on a new path with the production of the TRS-80 line of personal computers. Most were based on the Z-80 chip, but again, were memory limited. A number of other Z-80 based systems followed later, including the Osbourne and the KayPro Computers. These systems were based on the Digital Research CP/M operating system and had a maximum of 64,000 bytes of memory (64K). The Apple I1 Computer appeared in 1977. Newer models of the original Commodore Pet and an Atari computer followed. These machines were also limited to 64K of memory addressing, and the early models typically shipped with only 16K, 32K, or 48K of memory. The Z-80 and the 6502 were the first truly commercialized CPU chips touting boxes with key- boards, monitors (sometimes a TV), and the ability to expand (peripheral slots for serial communications, centronics parallel communications, etc.1. They all shared one technology, audio tape as a storage media. The use of a portable tape recorder provided inexpensive, if not always reliable, magnetic storage. The tape recorders were typically finicky and required patience to use. Adjustments to the volume control were often needed to find "just-the-right" setting for loading or saving information. This kept the personal computer from being accepted in many markets, and gave it a reputation as a hobbyist or experimenters&apos; toy. In early 1979, Steve Wozniak finished the design of a floppy disk drive and controller. This was a revolutionary design which reduced the "then" standard number of controller chips from fifty-plus, to just eight. With the advent of an affordable floppy disk drive mechanism, the personal computer was about to gain respectability. From a business standpoint, it was now possible to save and reliably retrieve business information. It also provided a superior means of distribution for commercially created software. Commercial software became a commodity rather than an oddity.

Jan 1, 1993

By Brian E. McGee

The Federal Coal Management Program represents the culmination of several years of effort by the Department of the Interior (001) to reformulate the manner in which coal owned by the United States is leased and developed. These efforts began in 1970 with a study by the Bureau of Land Management (BLM), which indicated that unless drastic changes were made in. the federal coal leasing procedures, federal coal lands would be leased almost for the asking while production of coal from those lands had been decreasing. Consequently, informal action was taken in 1971, which resulted in no further leasing being authorized until February, 1973. At that time, a formal moratorium on most coal leasing was established, with exceptions granted only for leases needed to satisfy short-term needs such as maintaining existing mines or supplying reserves for new contracts in the immediate future. This leasing policy embodied a long term objective of developing an entirely new planning system for federal coal leasing, as well as to schedule the preparation of a programmatic impact statement for this new system. As a result of the 1973 moratorium and the ensuing application of short-term criteria, only 10 federal coal leases (covering approximately 30,177 acres) were issued from February, 1973, through January l, 1976.

Jan 1, 1982

By V. Claremboux

The transformation of raw iron ore into high quality steel can take place via several processes. A general consistent theme involves the upgrading of the iron ores via methods such as flotation and magnetic separation, the preparation of an agglomerate such as via pelletization or sintering, the smelting of the agglomerate into a high grade iron product, and the further refining of iron into specific steel alloys. Each of these steps admit potential for optimizations and alternatives, and the process overall is critical to meeting the world’s continuing iron demands.

Feb 1, 2025