Search Documents

By T. McCallum, C. Cooper, B. Hutzler

"In copper solvent extraction, managing the quality of the organic phase is a key parameter to ensure optimal physical and metallurgical performance in the plant. Increased throughput as a result of declining ore grades coupled with advances in plant design and practice, resulting in reduced organic losses, has pushed the limits of the status quo with respect to organic quality. Clay treatment of plant and recovered organic at the optimal dosage is critical in maintaining quality, however, achieving the optimal dosage through existing filtration capacity and practice can be difficult. Cytec has developed a process aid that increases efficiency of existing filtration equipment that has been successfully implemented at two commercial SX operations. ACORGA® CB1000 enables higher dosages of clay while allowing for more efficient use of existing filtration capacity. This study analyzes results from commercial trials and demonstrates that improved organic quality and clarity is achievable through optimization of current treatment practices. INTRODUCTION Decreasing ore grades have prompted copper solvent extraction operations to raise PLS flow rates, increasing plant throughput to maintain production1. The ability to process higher flow rates through existing mixer-settlers historically came at the expense of increased entrainments2. However, advances in mixer-settler design, practices and improvements in organic recovery processes have enabled operations to maintain, and in some cases reduce organic losses while achieving higher flow rates through existing equipment. Based on the increased demand on the SX equipment and reduced losses (or more efficient recovery) maintenance of the circuit organic quality through efficient clay treatment is now more important than ever. This paper discusses common industry practices and related issues in organic clay treatment, and presents benefits achieved in commercial operations through the use of ACORGA® CB1000 Clay Binder. IMPROVEMENTS IN DESIGN AND PLANT PRACTICE Mixer-settler design has improved since the first commercial copper SX operation in the late 1960s. Advanced designs in mixer, settler, and settler internals have contributed to reductions in entrainments. For example, improved impeller designs have been reported to decrease organic in aqueous entrainment from the ‘old designs’ of 50-200 ppm3 to as low as 4 – 10 ppm confirmed via diluent and reagent consumptions . Similarly, operations are reporting a 20-50% decrease in reagent consumption when compared to the original design criteria3. Operations have optimized settler internals to increase coalescence and have improved settler operating practices which have been shown to reduce entrainments7. Comparison of the SX world operating data from 1999 and 2007 shows reductions in organic entrainment losses with increases in flow rates."

Jan 1, 2015

By S. S. Peng

The generation and transportation of the airborne dust are mainly governed by the velocity and the movement pattern of the ventilation air in the longwall face. Generally speaking, the higher the air velocity, the more the airborne dust will be generated and the longer the period of the dust of certain size will be carried away from the source. In order to effectively prevent the production and the spread of the airborne dust, The airborne dust concentration distribution in the longwall face must be known in advance. Before the dust concentration distribution can he predicted theoretically with confidence, the air velocity distribution pattern of the ventilation air in the longwall face area must be determined first. However, the complicated, time-dependent and unpredictable mining conditions along and around the face area make the theoretical studies of the problem rather difficult. For instance, one of the factors commonly affecting the air velocity distribution at the longwall face is the air leakage, either into or from the gob area. The leakage quantity and the location of occurrence differ from mine to mine, face to face, and time to time. They depend not only on the compactness of the caved roof fragments in the gob, but also on the degree of obstructions in the working space and in the return entry. Another obstacle to the theoretical studies about the velocity distrbution is the complicated boundary conditions of the ventilated spnce which is very difficult to represent accurately in mathematical forms. In this paper, the air velocity distributions measured in four longwall faces are presented. A statistical model for each longwall face is also derived for prediction of air velocity distribution in the longwall face.

Jan 1, 1985

By Arthur B. Cummins

It is appropriate to discuss diatomite at an AIME meeting in San Francisco. California has led the nation, and the world, in the production of diatomite products for more than 40 years. It appears that our State will maintain this position for a long time to come. Diatomite today ranks high in the list of California mineral commodities, with a total value since 1889 well in excess of $100 million. California's production has more than doubled since 1942. In 1959, the value of diatomite production in California is exceeded only by the following industrial mineral materials-borates, stone, sand and gravel and cement20,28. Also, not unimportant is the production of diatomite in each of our other Pacific Coast States, including Nevada. First, let us define diatomite. It is a sedimentary siliceous rock of organic origin, which consists mainly of the fossilized remains of diatoms. Diatoms are microscopic aquatic plants which have the capacity of precipitating silica bio-chemically so as to form a part of their organized structure. In the economic sense, we are not concerned with the numerous types of sedimentary materials which contain minor amounts of diatom residues, or with impure or highly indurated siliceous materials, which may have been formed from diatomite2. Diatomite (synonyms--diatomaceous earth, kieselgurO is a term generally restricted to material of such qualities as to be suitable for commercial uses. Diatomaceous silica is a designation which is best used to distinguish the basic component of diatomite, that is, the substance of the silica shell itself, and which is the major' constituent of beneficiated diatomite or processed diatomaceous products.

Jan 1, 1959

By P. Moyo, S. Dixon, R. Norcross

The separation and recovery of copper from cyanide solution has been investigated since the early 1900s. The precipitation of copper using sulfide ion was patented in 1911 by Williamson, published by Leaver & Woolf of the USBM in 1931 and Cyanamid in 1960s. The current practice of sulfide precipitation is used in various processes such as “SART" for cyanide regeneration and copper recovery. The precipitation of copper sulfide requires the pH of the clear solution to be in the range of 4-6. The precipitated copper sulfide can be sold to smelters. Alternatively, copper cyanide can be precipitated from clear solutions in the pH range of 2-3. However, selling copper cyanide is challenging because of its cyanide content. Past work has focused on the use of boiling sulfuric acid to convert copper cyanide to copper sulfate as published by Seracini in 1991. This paper describes a simple process to convert copper cyanide to copper oxide using sodium hydroxide at ambient temperatures. The cuprite can be sold to smelters or used as a feed to an electrowinning circuit to produce copper cathodes. The process provides an effective method to recover copper from cyanide solutions with a lower capital requirement.

Mar 2, 2022

By B. Salopek, D. Rajkovic, D. Rumenjak

In decision making support system, that are used in various fields of environmental protection (environmental impact assessment, environmental management systems, setting environmental standards and regulation, etc.), it is often important to apply various mathematical environmental engineering models. The question of linking environmetal engineering modeling to decision making support system used in environmental protection is not yet methodically solved. The reasons for that could be manifold. Decison making support systems, used in environmental protection, because they are simply taken from bussines decision making, are not often adequate for specific problems raised in environmental protection. On the other hand, there are great number of types of models in environmental engineering, what urges the problem of finding the way of their proper linking with decision making support systems. The application of fuzzy logic in that field is estimated as one of possible solution of the problem.

Jan 1, 2005

By Marietta Canty

Results are presented that were gathered during field-scale testing of an innovative technology, sulfate-reducing bacteria (SRB), designed to treat and control acid mine drainage (AMD). The project was performed under the Mine Waste Technology Program (MWTP), which is funded by the U.S. Environmental Protection Agency (EPA) and jointly administered by the EPA and the U.S. Department of Energy through an Interagency Agreement. The MWTP is implemented by MSE Technology Applications, Inc., located in Butte, Montana. A field-scale test is described in which the subsurface workings of an abandoned mine were used as an "in situ biological reactor."

Jan 1, 2000

By S. K. Kawatra, S. Valluri

With increased CO2 emissions from steel and coal industry, there is great opportunity to capture CO2 and utilize the captured CO2 for economic advantage. The primary goal is to develop energy-efficient processes that reductively couple CO2, an abundant and renewable carbon source, for the production of value-added chemicals such as methanol, ethanol, and oxalic acid. These chemicals can be used elsewhere in the refining process or sold as valuable by-products. Geological sequestration, in comparison, has no economic return. Current CO2 utilization research at Michigan Technological University focuses on electrochemical reduction of CO2. Electrochemical reduction of CO2 to hydrocarbons and other chemicals is a complex multistep reaction with adsorbed intermediates. The exact reaction mechanisms leading to various products are not clear from the literature to date and will likely change over the range of conditions like pH, electrode potential, electrolyte medium, catalyst, etc. This paper will present different ideas and their viability to utilize CO2 as a feedstock to produce several value-added compounds. INTRODUCTION Carbon dioxide (CO2) emissions into the atmosphere will need to be drastically reduced to curb the various undesirable effects of climate change. The large contribution in total CO2 emission originates from coal or natural gas power plants, and a considerable amount from steel plants. Average CO2 emissions in the US from steel industry is 2.9t CO2/t steel (Global CCS Institute 2013). Capturing the available CO2 from the steel and coal industries for economic advantage is a win-win situation for the industry. This technology is not only important scientifically but is also vital for a sustainable future. The various ongoing investigations can be categorized as biochemical, thermochemical, photochemical, and electrochemical approaches. Among these, the electrochemical method shows the most promise as an efficient form of CO2 conversion technology, because of its many advantages like high reactivity under ambient conditions and good extensibility from small- to large-scale processes1 BACKGROUND Extensive research has been done on the chemistry of transforming carbon dioxide into more useful products. Methods are known to convert carbon dioxide into a wide variety of substances, including methanol, isobutanol, carbohydrates, methane, carbonates, urea, formic acid, oxalic acid, carbon monoxide, epoxides, formaldehyde, and so on. Several of these (carbohydrates, formaldehyde, isobutanol etc.) are primarily results from biological processes. The rest are results of strong reduction reactions or electrolytic reduction. In short, electrolytic reduction can be used to form methane, methanol, formic acid, oxalic acid, carbon monoxide from carbon dioxide2. CO2 reduces at the cathode in an electrolysis cell. These processes have the general form of generating the carbon dioxide anion radical (2⋅−) and allowing it to react with itself or the electrolyte3. Catalysts can be added to influence the formation of the anion radical or to suppress side reactions3. The electrolyte, catalyst, voltage, electrode material and CO2 content are all known to effect the reaction pathway. Table 1 shows the overall reactions and energy requirements for electrochemical conversion of CO2 to chemicals

Jan 1, 2019

By E. A. Sondreal

Requirements of flue gas desulfurization (FGD) for Eastern and Western U.S. coals will not be the same because of differences in coal sulfur content, ash analysis, and beating value. The effects of these differences and of limited availability of water in the West are the subjects of this paper. Eastern and Central bituminous coals are generally high in sulfur and require removal efficiencies in the range of 70 to 90 percent to meet the Federal emission standard of 1.2 lb SO2/MMBtu. Ash in Eastern coals is low in alkali content and is relatively insoluble in scrubber solutions. High sulfur content and market availability make salable product methods more attractive in the fast and Central United States than in the West. Western subbituminous coals and lignites are generally low in sulfur content, however, only a few deposits could reliably meet the Federal emission standard without FGD, Required removal efficiencies generally fall in the range of 0 to 60 percent to meet the 1.2 lb SO2/MMBtu limit. If the standard were raised to 2 lb S02/MMBtu, approximately two-thirds of Western coals could be burned without FGD. Some Western coals contain ash high in alkali, some of which is soluble in scrubber solutions. This complicates scrubber chemistry, but it also provides the meant for displacing some or all of the limestone requirements when only moderate S02 removal is required. Dry areas in the West would benefit from full commercial developement of dry processes of FGD.

Jan 1, 1974

By R. P. Schneider

The Chino mine, concentrator, and smelter are located in Grant County in Southwestern New Mexico. Chino Mines Company is a partnership two-thirds owned and operated by Kennecott Santa Fe Corp., and one-third owned by MC Minerals Corp. (Mitsubishi) of Japan. The Chino Ore Body The Chino ore body is a widely varied deposit of rock types and contains intrusive stocks and sediments. The stocks contain chalcocite in a matrix of quartz, mica, and feldspar. Much of the feldspar is altered to clay. Some of these stocks are enriched with native copper. The sediments contain chalcopyrite associated with gangue minerals including magnetite, pyrite, garnet chlorite, and epidote. The contact of the stock and sediment is heavily altered to chlorite and clay. The stock ores contain economic quantities of molybdenite. The operating work index of Chino ore varies from 5 to 20 kwh/ton and averages 8.5 kwh/ton. The ore head to the concentrator averaged 0.81% copper and 0.010% molybdenum. Fifteen percent of the total copper head exists as nonsulfide mineralization.

Jan 1, 1985

By John A. Brooks

The description of a phosphate flotation operation is repeat information for many people, except for variations in flow sheets. This paper is written to show the variations in flows, and to give enough. of the overall flows to allow anyone not familiar with the operation to be able to formulate a fair idea of the operations.

Jan 1, 1962

Surface contamination of minerals during fine grinding may occur due to coating of one material on the other. This can alter the surface chemical properties and adversely affect the separation of minerals by physico-chemical processes. In dolomite-silica system, selectivity was completely lost (compared to a synthetic mixture) after wet grinding of the minerals in spite of using a dispersant. Adsorption and surface characterization studies were conducted on silica particles separated after grinding with dolomite. SEM-EDAX analysis indicated the presence of dolomite on silica particles, which could cause the loss of selectivity.

Jan 1, 1993

By John H. Paugh

Hydraulic slurrying and pumpability characteristics of phosphate matrix (ore) have not been quantitatively defined. An elemental triangular diagram analysis of rock/sediment texture is used to classify the nature of the ore; then related to empirical field data of hydraulic pressureand production yardage ratios. This experiment is applied as a geotechnical tool to provide empirical data of ore slurry and pumpability characteristics as key considerations in the design of slurry pipeline systems. A real texture variability maps are developed on a section of land to assist mine engineering planning.

Jan 1, 1981

By Keith G. Wallace

The effect of face resistance on ventilation air leakage through stoppings was measured in a twin development heading. Face resistance was varied by alternately tightening or loosening the face line brattice to change the line brattice leakage. Results indicated that tight brattice lines are necessary to maintain acceptable airflow at the face but result in higher leakage throughout the entire system, reduced overall ventilation efficiency, and higher operating costs. Conversely, a low face resistance which simulated an auxiliary fan/duct system gave reduced stopping leakage losses, higher quantities of air at the last open cross-cut and greater entire system efficiencies

Jan 1, 1984

By William F. Stowasser

The organization and operations of the information gathering system, and examples of the products prepared for the commodity phosphate rock by the Division of Nonmetallic Minerals, U.S. Bureau of Mines, are used to describe the Bureau's commodity program. Selected examples from publications about phosphate rock are used to illustrate the program. The Commodity Divisions reporting to the Office of the Assistant Director-¬Metals, Minerals and Materials, have the responsibility in the Bureau of Mines to maintain commodity records, understand the present supply and demand status of the commodity, and forecast future supply, demand, and problems. Within the Divisions, commodity specialists have the broad charter of acquiring as much information about a commodity as is necessary to characterize its history, current status, and future. This information and understanding are the base for the development of mineral policies. To accomplish these objectives, the commodity specialists acquire data and information about each commodity and produce a number of standard publications each year. In addition, as circumstances dictate, each specialist will prepare or participate in the preparation of special documents for specific purposes or problems associated with his commodity. In the preparation of reports and publi¬cations, he may communicate with industrial organizations and other Government agencies.

Jan 1, 1975

By Issac Douglas, Sheila Devasahayam, John S. Thella, Manoj K. Mohanty, Jeremy Prishmont

The flotation performance of Sodium O, O-diisobutyl Di thiophosphate (referred to as reagent A) was compared with Aerophine 3418A (referred to as reagent B) for floating a complex copper ore grab sample (Ore A). Preliminary test results indicated a cumulative copper concentrate grade of 10.19% with a recovery of 86.31%, which was achieved with reagent A from a feed consisting of 5.32% Cu. The grade and recovery achieved using reagent B are 9.11% and 87.85%, respectively. A comparative analysis based on the preliminary test results indicated that reagent A’s performance is better than that of reagent B at lower concentrate grades, specifically below 12% Cu. However, the flotation performance is better for reagent B at higher concentrate grades (>12% Cu). A more detailed study was conducted to optimize the grade-recovery performances achievable from both reagents on a complex low-grade copper ore sample (Ore B) from Western USA. Test results indicated a copper concentrate with a grade of 5.5% Cu and 78.59% recovery was obtained with reagent A compared to 4.31% Cu and 62.04% recovery with reagent B from a feed consisting of around 0.25% Cu.

Feb 22, 2026

By W. E. Horst

In Part I of this paper we describe two techniques that were employed in the development of mathematical descriptions of the size reduction process which takes place in a ball mill. In Part II we show how the comminution model was imbedded in a process model to effect steady-state and dynamic simulation of a closed-circuit grinding operation. Increasing emphasis is being placed on development of approaches whereby the essential characteristics of a process can be succinctly represented in terms of a mathematical description of the relationships that exist among important process variables. This activity, commonly known as mathematical modeling, predates modern electronic computers: however, these computers with their tremendous computational capability have given new impetus to the whole field. Although the computer is quite helpful in the development of mathematical models, the real value to the engineer lies in the fact that computers represent such a powerful tool for simulating systems described by mathematical models. As a consequence, engineers may simulate and thereby study the behavior of complex. interacting, systems over a broad range of process variables and configurations once appropriate process models have been developed for the sequence of steps comprising the process.

Jan 1, 1970

In the estimation of recoverable resources, geostatistical techniques such as Multiple Indicator Kriging require a change of support correction to derive theoretical recoveries based on an assumed level of mining selectivity. The change of support models most widely used in practice entail model based generalized corrections either on a global or local basis. Examples include the affine and indirect lognormal methods. Change of support corrections derived empirically through short-scale conditional simulation realizations often show notable differences compared with theoretical corrections determined using model variogram parameters. The existing changes of support models are reviewed and an alternative method is proposed.

Jan 1, 1999

By M. J. Shields

There are numerous suggestions in the literature on methods of obtaining representative samples of waste rock or mill tailings. Some suggested methods would result in thousands of samples and very high costs for a large facility. There is no general rule that can (or should) be followed, such as collection of a given number of samples per mass of material, per acre of impoundment, or per foot of drillcore. Each site is different, and the adequacy of sampling must be tailored to the site. A logical approach is to let the variability at the site dictate the number of samples that should be collected and analyzed, and then to quantify and evaluate the results by means of standard statistical methods.

Jan 1, 1998

By William F. Stowasser

The United States has traditionally been the world's largest producer and net exporter of phosphate rock and related fertilizer products with the exception of rock exports from Morocco. In recent years, however, U.S. producers have faced increasing competition from operations in foreign countries, leaving the future position of the U.S. phosphate .industry as a leader in the world markets somewhat less certain. This paper will review the U.S. phosphate rock industry in relation to its known demonstrated reserves, its historical and present production and export levels, and its future mining potential. The paper will include an analysis of the availability of phosphate rock in the United States represented by cost-tonnage relationships. The U.S. phosphate rock industry has for decades provided raw materials at reasonable costs to the phosphate fertilizer industry, and the fertilizer products have been made available to both domestic and international markets. Natural soils normally contain low quantities of phosphorus, and cultivation exhausts the available phosphorus through the removal of harvested products. Yields diminish, and it becomes necessary to apply phosphorus to the soil in an amount at least sufficient to compensate for removal. Raising the level of phosphorus also permits nitrogen and potash fertilizer nutrients to be effective and sustain the high crop yields necessary to support increasing food demands. In only a few areas of the world are soils, climate, rainfall, and low-cost phosphate fertilizer available to assure high agricultural yields in successive years. One of these areas is the central United States and south central Canada. By contrast, in the Soviet Union, the weather conditions in farming areas frequently cause crops to either bake or drown in the field. To attempt to counter the effect of weather on production, the U.S.S.R. has increased use of fertilizer and equipment in recent years. The effect of fertilizer on various crops has been documented, and in all cases, improvements in yield and plant development were noted, as was the ability of fertilizer to mitigate the effects of unfavorable climatic conditions. Phosphate resources can be classified as either identified or undiscovered. In the identified classification, we are principally concerned with demonstrated phosphate resources, or those that have been measured or indicated. In the southeastern United States, the phosphate mining areas of Florida and the Carolinas have been explored and drilled extensively in attempts to locate new deposits. The exploration programs indicate that another Florida Bone Valley Formation or North Carolina Pamlico River Deposit is unlikely to be discovered in the southeastern U.S. coastal plain. Phosphate rock deposits of commercial interest in the western United States are located in Montana, western Wyoming, northern Utah, and southeastern Idaho. The deposits are in the Permian Phosphoria Formation with most of the mining activity occurring in Idaho. Although substantial demonstrated resources have been identified, recovery costs and the field's isolation from markets have restricted growth of the industry in the west. The phosphate rock deposits in Tennessee are well known, and it is estimated that about 29 million metric tons1 are potentially recoverable. Undiscovered deposits of brown rock in Tennessee would likely be quite small.

Jan 1, 1985

By Sam Rosenblum

The anomaly ratio is obtained by dividing the analyzed value of an element by the anomaly threshold value of the element. The sum of anomaly ratios for all anomalous elements in a sample may be compared with similar sums for other samples, so that the samples having the greatest anomaly-ratio totals can be recognized easily. In partial or full-suites-of-ore-elements the use of anomaly ratios is more meaningful than analyzed values because the ratios quickly indicate anomalous elements and call attention to samples and localities that should be investigated.

Jan 1, 1980