Search Documents

By Todd S. Webster, Matthew J. Pierce, Brad D. Krumel

With the Working Shafts and Starter Tunnel under way, it became apparent this 4.7-mile, 19-foot diameter wet weather tunnel was going to live up to its name. The shaft’s pre-excavation grouting was completed, and ground water inflows were slowing project progress. As the tunnel drive was approaching 50% complete a cooperative effort was underway between the owner, engineer, and contractor to raise the base of the Retrieval Shaft by 65 feet to avoid ground water infiltration construction challenges. The tunnel alignment needed to be raised in kind. The project was behind schedule and rethinking the cast-in-place adit work was next on the agenda due to the very wet environment in the tunnel. The race was on to finish the project within the owner’s time constraints while completing multiple redesign aspects of the tunnel alignment and associated adit construction. This paper will evaluate original design criteria and actual in-route design modifications and change management to meet the owner’s just-in-time schedule needs.

Dec 1, 2022

By K. K. Cheng, Z. M. Chen, A. L. Mular

INTRODUCTION Since the nineteen fifties, process engineers have been seriously concerned with process models for various purposes (1,2,3). Models serve as subroutines to mathematical flowsheets which simulate circuits of interest. Simulators can serve to increase process know- ledge, assess circuit performance, investigate flowsheet modifications, evaluate new flowsheets, perform off-line optimization, and compare alternative control strategies. This chapter describes a methodology to develop a simulator of a bulk Cu-Mo circuit comprised of roughers, scavengers and 3 stages of cleaning. The simulator was employed to evaluate the influence of water addition at circuit points and to estimate the optimal number of cells for each stage in the circuit. DESCRIPTION OF CIRCUIT Figure 1 is a flowsheet of the Brenda Mines Ltd. (located near Peachland, B. C.) bulk Cu-Mo flotation circuit as simulated prior to an expansion/renovation which involved the installation of large, new flotation cells. Referring to the flowsheet, feed to rougher cells includes fresh feed, scavenger concentrate and 1st cleaner tailing. Rougher con, 1st cleaner (sect ion 2) con and 2nd cleaner tailing are fed to 1st cleaners (section 1). 1st cleaner (section 1) concentrate and 3rd cleaner tailing serve as 2nd cleaner feed, while 2nd cleaner concentrate is fed to the 3rd cleaners which produce a final bulk concentrate. Table 1 lists cell types and specifications important to the circuit. DEVELOPMENT OF MODELS To develop flotation cell models a systematic procedure was employed (4). This involves the selection of responses and factors, proposing models to be fitted, the acquisition of raw data, the statistical adjustment of raw data, fitting models to adjusted data and testing the adequacy of fitted functions. Responses and Factors Responses of interest included recoveries, concentrate grades and concentrate solids/water flow rates for each stage. Factors that influence these responses, such as reagent addition rates, air flow rates to cells, solids and water flow rates to stages and feed grades were not manipulated during the sampling period. Thus, the investigation was limited,

Jan 1, 1986

By B. G. White

Traditional interpretations of vein ore deposits in the Coeur d' Alene Mining District, such as the view that these deposits formed in a transcurrent tectonic regime during the Precambrian, are being supplanted by the view that the deposits (1) formed in low-grade metamorphic shear zones similar to those that host an important type of gold deposit, (2) display features, such as wall rock carbonate zoning and vein zoning, that are common to ore deposits elsewhere, and (3) are probably Mesozoic and possibly related to emplacement of the Idaho batholith. In recent years, new interpretations have led to major ore discoveries that are likely to extend the life of the district for decades.

Jan 1, 1998

By B. C. Scott

Every year more and more mining companies are entering joint ventures to look for minerals. Large companies join large companies, small companies join small companies, and large companies join small companies. Mining companies join oil companies, chemical companies, machinery companies, and companies with no other connection to the minerals business. And well they might, for here is a way for both minerals-oriented companies and those that have no background or knowledge of the minerals business to get actively involved in an outwardly-attractive but high-risk enterprise with the chance to participate in a lucrative minerals find. Thus, for reasons beyond those normally associated with joint ventures in many other fields, corporations, companies, groups, and even individuals are looking to joint exploration ventures as the answer to all problems of getting into or staying in mining.

Jan 1, 1972

By Jenna Wundrack, Evan Thibaud

The advanced cryogenic treatment is a post-manufacturing metallurgical process that involves subjecting off-theshelf materials to extremely low temperatures, significantly improving wear resistance and reliability. These case studies explore whether the claims of Enrich Bits & Tools benefit metals and their specific in-field application to drill bits in the blasting industry. This paper reviews the application of the treatment to button drill bits for enhanced wear resistance in two operations. The first is a civil construction project with highly abrasive rock. To confirm the remarkable benefits of the treatment, a second case study was performed. This case study utilized measure-while-drilling technology in consistent rock characteristics to reduce variables in the field study.

Feb 1, 2024

By Marietta Canty

Results are presented that were gathered during field-scale testing of an innovative technology, sulfate-reducing bacteria (SRB), designed to treat and control acid mine drainage (AMD). The project was performed under the Mine Waste Technology Program (MWTP), which is funded by the U.S. Environmental Protection Agency (EPA) and jointly administered by the EPA and the U.S. Department of Energy through an Interagency Agreement. The MWTP is implemented by MSE Technology Applications, Inc., located in Butte, Montana. A field-scale test is described in which the subsurface workings of an abandoned mine were used as an "in situ biological reactor."

Jan 1, 2000

By A. Supomo, A. Partanen, M. Mular

Although many SAG operators may agree that on-line measurement of SAG feed-size is an attractive notion, applying this information in a control strategy that recovers the investment, engineering time, and maintenance is not necessarily straightforward. The P. T. Freeport Split-Online system was justified based on the assumption that SAG feed-size could be used in a feed-forward control strategy either at the regulatory or expert system control level. Something like “as the feed size changes adjust the throughput to avoid under or overloading the mill” was envisioned. However, following installation and calibration, Cluster Analysis showed that such an approach would not be successful. However, the sensor has been successfully integrated into Freeport’s grinding control strategy other ways. It provides an input to the Kalman filter parameter estimator used in a model-based control strategy that optimizes throughput and grind. The Split sensor also provides a characteristic feed size parameter for use in an on-line work index estimator. This paper describes the calibration and installation of the Split SAG feed-size analyzer, and reviews the evolution of its use in the Freeport C3 grinding circuit control strategy.

Jan 1, 2001

By D J. Bradshaw

It is well known that the chemical environment determines the success of the flotation process, however its characterization and control is difficult to achieve. This work evaluates the use of various measurements, including mineral potential measurements, in gaining an understanding of the influence of varying parameters such as the milling media and the reagent suite composition on the flotation performance of a platinum group metal (PGM) bearing ore. The results showed differences in the response of the various mineral electrodes to the different conditions, however the changes in flotation performance of the different minerals in the ore could not be wholly described by the electrochemical changes, demonstrating the limitations of these measurements.

Jan 1, 1999

By D. H. Stonehouse

There is no such thing as an industrial minerals industry. There are, however, many industries operating in the general field of industrial minerals. And although we use the phrase "industrial minerals industry" out of sheer convenience, the only common denominator among, say, the potash mining and processing industry, the sulphur-sulphuric acid industry and the granite industry is, in fact, that they each are exploiting an industrial mineral resource. May I quote the person whom I consider to be the reigning Mr. Industrial Minerals, Robert L. Bates, who in the 4th edition, 1975, of Industrial Minerals and Rocks states: "An industry is considered to belong to the industrial minerals field if its operations consist of extraction and processing, but not manufacturing. Thus the mining and beneficiation of feldspar is a mineral industry, but the manufacture of ceramic products is not. In the cement and lime industries, processing merges into manufacture, and the line is less distinct. It disappears altogether in a plant that extracts salt as artificial brines, and makes sodium and chlorine chemicals, all under the same roof."

Jan 1, 1981

By R. Casagrande, L. R. Moore, J. Sessoms, P. Macy

"A South American nickel mine has been producing a nickel concentrate that also contains copper and iron (15 percent nickel, 5 percent copper, 28 percent iron) for the end use of stainless steel production. A critical specification for the quality of the steel is the iron to magnesium oxide ratio (Fe:MgO), with a ratio of below 3.5:1 having a substantial impact on the nickel value. This nickel concentrate producer historically mined the sulfur-rich mineral pyroxenite but had been forced to move to a magnesium oxide/silicate (MgO/SiO4)-rich mineral harzburgite, resulting in nickel recovery being reduced to around 50 percent to maintain the required Fe:MgO ratio. In this study, ore mineralogy, water chemistry and the chemistries associated with the flotation process were evaluated in an effort to increase nickel recovery while maintaining the Fe:MgO ratio according to specification. New chemistry was introduced with the specific goal of complexing with the MgO and retarding its interaction with the bubble flow in the flotation process.IntroductionGlobal nickel production in 2011 totalled to 1,770,000 tons, according to the Raw Materials Group (2013). From 1950 to 2005 there was an aggregate 4.4 percent increase in nickel production, with a market-value high of $1,000/ton nickel reached in 1998 (Mudd, 2010). Approximately 65 percent of nickel production is consumed by the stainless steel industry, with 12 percent of the remainder used in super alloys or nonferrous alloys. Nickel imparts corrosion resistance, temperature resistance and other benefits to its alloys (Table 1) (Oberg, 1996; Cáceres, 2003). The dominant types of nickel-bearing ores are classified as either laterites (limonite: nickel-iron oxide; and garnierite: nickel hydrosilicate) or magmatic sulfide deposits (pentlandite: iron-nickel sulfide) (U.S. Geological Survey, 2013a, 2013b). In 2012, about 40 percent of the nickel ore mined was sulfidic-type ores and about 60 percent was laterite. The processing of laterite ore is expected to continue to increase as the availability of sulfidic ores continues to decline."

Jan 1, 2015

By Richard R. Klimpel

INTRODUCTION Previous papers by this author have discussed some of the difficulties involved with optimizing the performance of industrial flotation circuits, e.g. Klimpel (1988, 1989). The two major problems seem to be: 1) the inherent "systems" nature of the froth flotation process which leads to a great deal of self-compensation among the various operating options available and 2) the inherent variations in mineralogy, water chemistry, etc. that always seem to be present in industrial operations. In particular, the influence of reagent dosage has been emphasized in the above referenced work including an industrial system interaction denoted as the R/K trade-off, Klimpel (1984, 1987). Using a simple two parameter model for fitting time - recovery data, Klimpel (1980): [ ] where r is cumulative recovery at time t or at the t th cell, R is the long-term equilibrium recovery and K is the first-order rate of mass removal from the cell (time ), the definition of the R/K trade-off with increasing reagent dosage can be given as follows: at low dosages both R and K increase, at intermediate dosages R continues to increase but K starts to level out, and at high dosages, R may flatten out or still continue to increase but K starts to decrease, sometimes rather quickly. An illustration of this effect in a batch laboratory flotation cell is given in Figure 1. The purpose of this paper is to give a detailed plant illustration of this R/K trade-off phenomena with changing collector dosage which shows just how highly interactive the grindinglflotation system in sulfide mineral processing really is. This is one of about 20 plant level case studies that are being presented and evaluated in an upcoming book, Klimpel (1990). The particular study given here was completed in late 1979 on a copper ore of head grade 0.93% Cu. The frother being used was Dowfroth* 250 at a constant dosage of 0.15 g for each ton of solids feed to the rougher bank and the slurry pH was 10.2. The motivation of the study was to better understand the relationship of changes in feed rate (hence in particle size and state of liberation) with variations in collector dosage (potassium amyl xanthate). The major concern was to determine how much extra economic benefit could be gained by better utilizing the existing grinding mills and rougher bank consisting of eight identical cells. The remainder of the flotation circuit was also studied, including regrinding of rougher tails, but did not prove as critical as the rougher bank operation itself. It appeared from an overall economic viewpoint, the battle was being won or lost in the manner in which the rougher bank was being operated. This was not to minimize the roles of the scavenging and cleaning circuits but those portions of this particular circuit could be rather obviously operated to achieve maximum benefit given the specific output of the rougher bank. A special attempt was made to maintain constant ore type throughout the entire test program. Eight specific test conditions were evaluated including three different feed rates (and hence three different size distributions) to flotation. Tables 1 and 2 summarize the eight test conditions and overall recovery results at the end of the rougher bank for each test. A single test consisted of at least three consecutive eight-hour shifts operating at steady-state with composite cell lip samples taken over the final eight-hour shift. "Trademark of The Dow Chemical Company

Jan 1, 1990

By D. Bahrami, W. K. Asante, G. L. Danko

It is prudent to interpret atmospheric monitoring signals in real time for checking the safe limits of the air conditions in underground mines. In gassy mines, real-time evaluation increases the safety of operations. In all mines, continuous monitoring and evaluation contributes to maintaining air conditions within healthy and safe limits. Signal interpretation for safety conditions in mines is difficult for many reasons. An increase in hazardous contaminant concentrations can be predicted by signal pattern recognition, root cause analysis of rapid changes toward deterioration, and forward prediction in time using algorithms and numerical models. The paper describes an early warning system for analyzing monitored signal patterns continuously in real time as well as forward predicting the various environmental and working conditions to recognize dangerous trends that may affect safety and health in underground mines. A dynamic, numerical ventilation model with heat and gas contaminant simulation components is used for the analysis of atmospheric data. Methods and test results are discussed with numerical examples for signal propagation prediction. Several mine examples are studied using controlled, synthetic data for malfunction simulations to evaluate time delays between the detection time of suspicious signal trends and the time of dangerous threshold crossing marking an accident scenario. Delay time is found in the order of 20 min in the examples, signifying the useful time period for preventive intervention between EWS warning and the likely breakout of a following accident.

By Denys B. Smith

Electric logs and cuttings records from Zechstein 3 and 4 strata in boreholes in the British Sector of have been interpreted in the light of numerous cored boreholes through this sequence in north-east England. This interpretation shows that potash salts in the two cycles are thickest and most consistent in a belt 20 to 40 km wide parallel with and a few kilometres from the present basin margin, and are here generally similar in grade to those known onshore. The potash ores in both cycles are mainly of sylvinite in onshore areas, the layered Upper the Southern North Sea Potash of the fourth cycle being rather less variable but generally of appreciably lower average grade than the Boulby Potash of the third cycle. Potash salts in both cycles are highly variable in thickness and grade in basin centre areas where they have been grossly affected by diapirism of the thick second cycle salts.

Jan 1, 1978

By Dwane K. Johnson

INTRODUCTION The small mining company faces the dilemma of how to finance the development of its properties because it doesn't have the financial resources to pay for the development costs from its own funds and doesn't have the financial strength which will enable it to borrow the money needed for development. However, with a little imagination and the right set of circumstances, a financing can be arranged for the small mining company. This paper is an attempt to describe the fundamental steps on how such financing can be obtained --in other words--what is required to provide ad- equate capital at a low cost for developing and bringing a mining property into production. Innovative financing follows from this. The basic keys for building and maintaining a successful mining company are "the four M's": Management, Market, Mine, and Money. The writer believes their order of importance is as presented and each is a building block required in order to obtain the type of financing that best suits the borrower and lender. MANAGEMENT Management must be experienced, highly organized, realistic, able to take advantage of opportunities and fulfill promises. Mine financing requires a variety of skills and concentration on the part of management. Management should have a thorough understanding derived from experience in geology, construction, mining and metallurgy and environment, marketing, and financial matters. Management must realistically visualize what will be produced at what cost and truly evaluate the risks associated so the proper security can be correctly designed. Since risk cannot be eliminated, the objective of management is to identify the risk which will be present in a given venture and assess the level of that risk which will be acceptable to the firm. Generally the risk which is present is subject to little or no modification. After management identifies and measures the acceptable risk the firm will proceed in a way that it will be least exposed. Management must determine its long-term objectives and strategies within the context of a constantly changing world. This question must be addressed before examining the sorts of risk which affect the development and operation of a specific property. The compilation and interpretation of "hard data" by competent people is good to a point but the experience and instinct of seasoned individuals are the important factors in management choosing a long-term direction for the corporation. The attitude towards risk greatly affects the goals of the corporation. Major risks in a mining project can be placed in four categories: 1. Market - Price, demand, substitution. 2. Costs - Capital, operating, financial. 3. Regulation. 4. Taxation. The feasibility study for a project is the fundamental tool used in the management of risk. Management should employ an experienced team with an established and well-understood set of ground rules for the preparation and assembly of a feasibility study. The necessary degree of realism is built into all levels of the study and if the project is technically feasible, the company's hurdle rate is then used to discount the base-case project cash flow in order to determine its financial viability. Understanding the geological significance of the mineral deposit is critical. There should be strong interplay among the pure regional geologist, the detailed mine geologist, the mining engineer, and the metallurgical engineer. The collaboration among these different disciplines will yield a feasibility study that is more reliable. The essence of this work must be appreciated and understood by the executives planning the financing. It is vital that they thoroughly understand the risks and make the proper risk assessments to cope with our rapidly changing market environment. Projecting future revenue values is paramount and is subject to much estimation. One way to mitigate fluctuations and the risk of falling prices is by selling production for future delivery. MARKET Since mining is a worldwide industry it is mandatory that bankers be aware of what is occurring in the marketplace, both foreign and domestic. The marketing of the production is a very important facet when considering financing for the small

Jan 1, 1987

By Geoff W. Seward, Charles J. Maes

INTRODUCTION The work of the metallurgical engineer engaged in developing a leach, solvent extraction electro- winning process usually begins in the laboratory and generally proceeds via pilot plant testing before finally resulting in a commercial operation. The path leading to the development of the eventual process will involve a test program on leaching in order to derive information on the amenability of the copper-bearing material to acid dissolution, under various conditions. Commonly in North America the leach process of choice is either dump or heap leaching but it may also be in-situ leaching or the treatment of mine waste- waters and bleed streams. In the past, agitation and vat leaching have also been included in the list of options. Currently the economics of copper production dictate that only material of mineralogy and grade, capable of being leached without prior milling, will lead to a viable process. This is not necessarily true in other parts of the world where grades are higher and milling costs lower and therefore this paper con- fronts all the techniques available to the metallurgical engineer in terms of the evaluation of the solvent extraction process. Understanding the objectives of a laboratory and pilot plant evaluation of a solvent extraction route is important and these are described in some detail in this paper. Of at least equal importance is understanding limitations of such a test program and this aspect of process development is also discussed with reference to the kind of equipment and experimental practices that have been shown to produce results consistent with the objectives. WHERE TO BEGIN? At the inception of a project much information is developed on the variables of the leach process and indeed in some instances the type of leach that best suits the ore to be treated is the subject of intense investigation (Wadsworth 1983). The decision to treat the leach solution by solvent extraction focuses attention on the selection of the extractant most suited to the nature of the chemical composition of the solution. A laboratory screening program will probably need to be arranged in order to assist in narrowing the options and the following is suggested for this initial screening. Selection of a Representative Leach Solution This is preferably obtained from leaching a representative sample of the ore under conditions likely to pertain in the commercial leach circuit. As the conceptualized circuit flow sheet will undoubtedly involve the recycle of aqueous solutions via the leach, then it is desirable to know the nature of and the likely level of the impurity ions in the solution as well as the concentration of copper. The other most important parameter that is required is the free acid (Anon, Acorga Analytical Method) content of the solution. As a rule of thumb, it is always true that recovery across SX is maximized as the pH of the leach solution rises. Whilst a high pH may be desirable for SX recovery, it is not always desirable for the pH (or more correctly, the free acid) of the leach to rise too high. The working range, therefore, tends to be between 1.5-2.5 pH. At an early stage in process development it is likely that a number of ill-defined conditions will exist, making it difficult to decide on typical leach conditions in which case the screening tests should be carried out using a synthetic leach solution prepared from laboratory chemicals. In doing this the copper and free content should be carefully controlled along with the appropriate addition of major impurity ions as their sulphate salts. Preparation of Suitable Organic Solutions Manufacturers information sheets on the reagents to be tested are required at this stage The information necessary to make an informed judgment on reagent performance is: Copper Uptake Value. This will indicate the amount of copper that can be extracted by a reagent as a function of its operating concentration in a

Jan 1, 1986

By Paul M. Keyser, Donald G. Foot, Jeffrey D. Mckay

In the past 30 years, there have been tremendous advancements in the uses and applications of column flotation. From their first use as final cleaners that could produce excellent grades at the cost of recoveries, columns are now being used in every stage of the flotation circuit as well as is SX-EW. Columns as roughers, final scavengers and even at the end of CIL circuits, are finding their way into the marketplace. Operational results of these new uses are presented. INTRODUCTION Flotation columns have been in use since the early 1950's in the U.S. (Hollingsworth, 1952) and the early 1960's in Canada (Trembley, Boutin, Wheeler, 1963). Application of column flotation has been somewhat diverse. In the early years, columns were used predominately for molybdenum cleaning in Canada and for phosphate flotation in the United States. Unfortunately, results met with skepticism and disdain as the columns were hard to operate, temperamental and although producing high grades, could not achieve acceptable recoveries. Since the inception of column flotation technology, the degree of knowledge for design and operation of columns has vastly improved. Despite improvements in the technology, there is still some reluctance by mineral producers to investigate the use of column flotation cells for processing stages other than cleaner flotation. This characterization is in part due to the proven advantage of flotation columns in reducing gangue entrainment in the froth product which results in higher grade products and/or fewer processing stages. Also, during the development of column technology, different types of spargers have been used with varying degrees of success. Furthermore, the general knowledge base of parameters affecting column flotation design and operation have advanced tremendously. Inefficient, or primitive, sparger design, coupled with the lack of column design and operating knowledge and experience, resulted in poor metallurgical and mechanical performance in many cases. Unfortunately, this lack of knowledge caused many column installations to be characterized as failures. The industry felt that columns could not achieve high recoveries, especially when dealing with coarse particles. Therefore, columns were characterized as cleaners, where low recoveries could be tolerated as recirculating loads rather than direct losses and froth cleaning advantages of the quiescent column flotation regime could be realized. Fortunately for the minerals industry, some producers have stood at the forefront of technology and allowed the column to be utilized for new applications. In the last decade, column flotation applications have expanded to virtually every mineral system and plant location throughout the world. The expanded application of columns has generated a new wave of interest for processing various streams. One of the most notable is in the use of columns as rougher cells. This is of particular interest to "green-field" plants and plants where expansions are taking place. Here, metallurgical superiority can be combined with maximum capital and operating cost advantages for a rapid return on investment. The superior results experienced to date, have generated a cohesive vision of the future in mineral processing where flotation columns function as single stage primary separation devices (roughers) with a single stage cleaner, if necessary. The advantages of column flotation go far beyond their original uses. We now have seen columns used as final tail scavengers, in SX-EW plants and even at the end of CIL circuits. Some of these cases will be reviewed. CASE STUDIES In an attempt to show the diversification of column flotation to many facets of the mineral processing plant, a variety of case studies will be discussed. Some of these were designed by the authors while others have been provided by plant sources. It is important to note that in each successful case, the columns were designed using the author's design and scale-up approach. This method assures that the columns are designed correctly for their particular application. For successful

Jan 1, 1993

By Joseph T. Duncan, Syd Peng, Larry G. Stolarczyk

The mining business has numerous risks: equipment availability, labor disruptions, foreign exchange rate, etc., but one of the more important risks is assessing the geology. Improving the “intelligence” of geology can and will have significant positive effect on reducing mining risk and thus enhancing operational and financial performance. The use of the advanced Radio Imaging Method (RIM-IV) on coal seams and ore bodies can create useful two-dimensional (2-D) and three-dimensional (3-D) high-resolution images that provide mining engineers with additional intelligence to better plan and improve operations. Improved operational performance will reduce costs and enable mining companies to meet market and financial commitments. For the past decade the underground coal mining industry has been moving toward “super panels” in long-wall mining, and “super sections” for room-and-pillar mining. These mining conventions employ wider faces, longer gate roads, greater room-and-pillar density, and an increased scale in the amount and complexity of mining equipment. An obvious economy of scale exists: amortization of setup investments over greater volume of coal enables mine management to reduce fixed cost per ton. Restricted by equipment considerations, face widths have currently reached about 1,100 ft. Wider longwall panels are planned, with 1,400-ft widths, but this requires an incremental step in hardware that the original equipment manufacturers will soon bring to market. However, longwall panel length has not yet reached its limits, with some panels planned up to 25,000 ft. While longwall panel length is generally dictated by reserve size and extent, practical restrictions in mine planning also include seam thickness, ventilation requirements, or restrictions involving methane drainage. Super panels have certainly enabled the industry to keep pushing the limits of productivity improvement. However, important considerations in mine planning, now and especially in the future, will be driven in large part by geological factors. While larger developments improve productivity and capture economies of scale, the fact that super panels can contain at least four times the area or coal volume means that the probability of encountering serious anomalies is at least four times greater than with the “conventional” panels. Given the increased probability of encountering anomalies, improved assessment of geology is important for super panels and super sections. Proper due diligence requires a thorough and competent evaluation of a mining property and its ore reserve. Using improved geostatistical techniques is most important, and improving the base data for the analysis is equally important. The old cliché “garbage in, garbage out” certainly applies. Also, the quality of coal reserves is (or has been) declining, so, in the future, mining will be in deeper and most likely thinner seams—and these seams appear to contain greater anomalies that threaten efficient operations. To counter the impact of reserve deterioration, the industry is moving toward greater use of geophysical tools and services. Fortunately, tools such as the Radio Imaging Method™ (RIM-IV) system have been improved and can provide the industry with enhanced 2-D and 3-D images of coal seams and ore bodies. To identify and profile the best areas of a coal reserve, geologists, engineers, and mine managers need greater intelligence in the form of RIM-IV tomographic maps of longwall panels and room-and-pillar sections. These images have enhanced the understanding of in-seam features, which in turn has improved operational plans and performance.

Jan 1, 2005

By R. Kahrger

This paper is written to convey the latest developments in compact bucket wheel excavators (BWE's) operating in medium-hard rock and will serve to indicate that BWE and compact machines in particular do in fact have application in materials other than loose sandy soils and soft rock. A recently run extensive three month field test in hard marl, which was previously considered too hard and difficult to be handled by a BWE, is used as an example to explain some of the design requirements and problems associated with digging harder materials.

Jan 1, 1990

By John Marsden, Mike Botz

A variety of modeling techniques can be utilized to forecast metal production at heap leaching operations. These approaches reflect a wide range of complexity, flexibility, time to implement, cost, and accuracy. For many operators, a spreadsheet-based modeling technique is attractive since the calculations are directly accessible, models can often be developed by site staff, and the results are generally easy to extract and interpret. The authors have developed a spreadsheet-based modeling technique that provides a high degree of flexibility, while still considering detailed operating information for ore properties, leach kinetics, scaleup factors, lift height, and in-heap metal inventories. The technique involves establishing kinetic leach curves for each ore type to characterize metal extractions, followed by application of separate metal recovery curves to define the rate at which leached metals exit the heap in pregnant solution, taking into account delays due to the in-heap solution inventory. At any point in time, the difference between total metal extracted and total metal recovered is equal to the in-heap inventory of the leached metal. This modeling technique is particularly useful for larger multi-lift heaps where delays in metal recovery are appreciable due to in-heap solution holdup. The technique is also applicable to sites with multiple heaps, leach cycles, and/or metal recovery plants (e.g., carbon columns for gold; solvent extraction for copper). This paper describes the modeling technique, including input data required and methods for defining kinetic leach curves and metal recovery curves. The technique is compared against an alternative spreadsheet technique using a simplified in-heap solution inventory calculation to forecast metal production, which has proven to be effective at a number of sites.

Sep 3, 2019

By John G. Hall

Everyone forms his own mental picture when the subject of copper is mentioned. To an architect, copper is a warm, enduring metal with a quiet beauty; to the historian, man's first metal; to the product engineer, the best electrical and thermal conductor of all commercial metals; to the investor, a volatile stock; to the speculator, the daily price quotation; to those in the mining industry, the challenge of producing copper for rising needs in the face of rising costs and lower grades of ore. At this meeting, we will look upon copper as a key raw material in industry, in national defense, in technology, in world trade, and as a principal commodity in the economies of several developing countries. As miners, and most of us here are miners, we are prone to view our role as suppliers of copper. We locate, mine, smelt and refine the metal. In the complexities of today's world, however, following a period of the longest domestic copper strike in history which caused critical world-wide shortages and widely fluctuating prices; it becomes necessary for all of us to concern ourselves with the whole spectrum of copper affairs -"from mine to consumer " But first we need to look at the miner's side of the picture -- capacity and production. We will examine these functions in terms of the whole world -- not simply the free world. Nature did not endow all regions of the earth equally, and copper in world trade has a way of ignoring political boundaries. Science and technology, as well, know no national boundaries. It is said that the "Engineering & Mining Journal" has as many readers in the Communist World as in the Free World. Nor is this a one-way street. We presently have available to us in the. U.S., cover-to-cover translations of many Communist World mining and metallurgical journals.

Jan 1, 1968