Search Documents

By B. Boutilier, R. Mendoza

"First Majestic Silver Corp. (FMS) is a silver mining company founded in 2002 that operates exclusively in Mexico. It has six producing silver mines, one of which is the La Encantada silver mine (La Encantada) located in the state Coahuila. La Encantada is located near the southern United States border and 708 km (440 miles) north of the city Torreon.La Encantada is located in the Sierra Madre Oriental and is a high-temperature carbonate replacement deposit. Mineralization in La Encantada occurs in many different forms such as veins, chimneys, breccia pipes and reefs (mantos). Mineralization is mainly oxides of iron, zinc, lead and manganese, with high concentrations of sulfides at depth relating to two main intrusive events: the Milagros Intrusive and the La Prieta Skarn.Mining began in La Encantada during the 1950s with small vertical shafts, drifts and raises. It focuses on the high-grade silver zones using traditional hoists and extraction methods, before branching into two main separate mining camps: El Plomo and Penoles camp. Penoles, the previous owner, focused mainly on large ore bodies using post pillar cut-and-fill mining method to extract the higher-grade material. Due to the type of ground, irregularity of pillars, and rock conditions, large amounts of high-grade pillars had to be left in situ to ensure the stability of the excavations. The mined-out areas would then be filled with lower-grade material to assist in the stability of the secondary level. These room-and-pillar development entries were 2.5 m x 2.5 m (8.2 ft x 8.2 ft) and spaced every 10 m (32 ft), leaving a vertical pillar of 7.5 m (25 ft). First Majestic acquired La Encantada in 2006. After the acquisition of the mine, the company began the conversion of the surveying reference system from a local grid (Maria Isabel Shaft as 0,0) to the Nav27 coordinate system, and subsequently converted to the WGS84 coordinate system in 2015. Due to the extensive history of the mine, different areas were surveyed with different systems, causing significant challenges when designing the principal extraction levels, pillar heights and ramp locations. To overcome this difficulty, the entire mine was resurveyed and the old workings transposed to the new coordinate system, except for some inaccessible areas due to poor ground conditions or ground collapses. To further ensure pillar height and the safety of the mine workers, probe holes were drilled during the development process."

Sep 1, 2019

By William J. Miles

For compliance with the Hazard Communication Standard and other federal and state regulations, numerous minerals, chemicals and products need to be evaluated for crystalline silica content at a threshold of 0.1 %. The polymorphs of crystalline silica that can occur in chemical and mineral products are quartz, cristobalite and tridymite. Other natural, industrial and synthetic amorphous silicas and hydrates must be distinguished from these polymorphs to prevent over-regulation in the workplace and environment. A number of industrial silica products are composed of glasses, expanded perlite, diatomite, slags, and precipitated and fumed silica products. Amorphous silica hydrates used for industrial products, include opal (hydrated silica of biogenic or inorganic origin), perlite, pumice and tuffs. In addition, crystalline and amorphous silicate minerals and chemicals, abundant in nature and industrial products, must be distinguished from the polymorphs of crystalline silica.

Jan 1, 1997

By E. A. Noble

In the Western Coal Region, successful reclamation of surface-mined areas includes the protection of groundwater sources. To accomplish this, a complete understanding of the geohydrology of the affected area is imperative. Successful mine design also calls for careful attention to geohydrology. Because the Western Coal Region is semi-arid land used mainly for farming and grazing, groundwater is a particularly sensitive topic. It is especially sensitive where the lignite scheduled for mining is itself the aquifer supplying the farms and ranches. Such is the case throughout much of the Western Coal Region, particularly where there are no near-surface sand and gravel aquifers that are commonly found in the glaciated portions of the Region. Just as mining can adversely affect groundwater supply, so can groundwater adversely affect mining. Mine flooding and highwall instability are examples of this. But, mine operators must realize that procedures they use to remedy geohydrologically-related mining problems can have a dramatic effect upon ground- water conditions in areas adjacent to the mine. A logical precaution is to require the acquisition of complete baseline data prior to making the first cut. We recommend that the mining plan not only incorporate the reclamation plan, but that they be developed as one plan.

Jan 1, 1976

By T. P. Meloy

Traditionally the mineral and mining engineers have characterized particles by sieving and-settling. Within the last decade, with the advent of the scanning microscope, entirely new experimental and theoretical approachesl-10/have been taken to minutely define the particle surface. This approach depends upon a hypothesis which takes advantage of the recent developments in automatic micro-scopes which can acquire large amounts of information in a short time and the new computational techniques which rapidly reduce the information to meaningful, practical data. Historically sieving and settling are the oldest sizing techniques known. Sieving by square screens, shown on Figure l-A is a common, current practice for sizing particles both in the laboratory and in production. A woven cloth is used which usually has square openings. The size particle that will pass through the opening dependent on a complex relationship of its morphology. As can be seen in Figure l-A, neither the width nor the height of the particle is determined by sieving. From square screens one and only one parameter characterizing the particle size is obtained, that parameter is the radius of the sphere that will just pass through the given sieve opening. A variation of square mesh screen is the slot screens, shown in Figure 1-B. Here another measure more closely associated with the height of the particle is obtained. Once again, one and only one parameter is associated with the particles' shape.

Jan 1, 1977

By Edward H. Eisenbrey

This paper is primarily concerned with the exploration for massive sulphide orebodies. In a discussion of this type, it seems appropriate to establish a few definitions so that all parties may consider the same beast and its habitat. First, the term "massive sulphides", as used here, not only denotes a body of mineralized rock containing in excess of 50% sulphides by volume, but a mass of sulphides that respond as a conductor to the electromagnetic (EM) systems currently in use in exploration. "Disseminated sulphides" refer to all of those sulphide occurrences that respond to the Induced Polarization (IP) geophysical methods most commonly in use in porphyry copper exploration. This latter definition may also include the disseminated sulphide halos so frequently found associated with massive mineralization as well as banded and stringer sulphide mineralization. It is plain to see that these two end members of our definitions can easily blend into each other. The term "volcanogenic" refers here to any and all geologic processes that have their origin in volcanic activity. Thus we are concerned here with the exploration for massive sulphide ore deposits derived from and affected by contemporaneous and post mineral volcanic activity. Furthermore, most massive sulphide deposits are apparently formed in a submarine environment, deposited with extrusive rocks and sediments and/or chemical hot spring accumulations, then enclosed and protected by the addition of more volcanic and sedimentary material then, probably folded and deformed into one of their myriad of shapes.

Jan 1, 1973

By John E. Miller

Unit Rig & Equipment Co., manufacturer of Lectra Haul Trucks, is continually studying methods of reducing the operating costs of large haulage trucks. Reduction of haulage system operating costs is an important goal that equipment operators and equipment manufacturers constantly try to improve on. One of the most variable and important factors affecting operating costs is actual truck operating practices. An examination was centered on methods to optimize truck utilizaion. It was found that a very effective method of accomplishing this goal would be an Automatic Truck Control (ATC) system to automatically control a fleet of haulage trucks in a predetermined pattern. Economic studies were conducted which showed a very favorable reduction in mine operating costs by use of an ATC system. In 1970, Unit Rig & Equipment Company, in conjunction with SAAB-SCANIA began preliminary development of adapting for truck use a proven automated control system previously used for train systems, small trucks, and military target vehicles.

Jan 1, 1979

By Nelson R. Shaffer

Implementation of the Clean Air Act Amendments of 1990 is negatively affecting production of coal used for generating electric power in Indiana and elsewhere in the Midwest. Required reduction of sulfur compounds from gas streams, or flue gas desulfurization (FGD), as mandated by these laws has encouraged installation of wet limestone scrubbers at many generating plants. Increasingly stringent requirements that will begin in 2000 are expected to necessitate even more extensive use of such scrubbers. Indiana has large deposits of limestone-the major consumable alkaline raw material for scrubbers-that can meet an expected demand of several million tons per year. Limestones are not, however, all the same. Different limestone units behave quite differently when used as scrubbing agents under differing conditions in actual practice. Decisions about FGD scrubber details would be more meaningful if made with thorough knowledge of which rock units contain the most efficient FGD limestones and which sites of suitable stone are located nearest to power plants. Even though abundant carbonate rocks occur in Indiana, their suitability in scrubbing systems has received little attention, and few attempts have been made to match details of stone resources to the needs of various utility scrubbing systems. Optimization of the fit between geologic characteristics of the existing limestones and prospective scrubber systems should allow for greatly improved planning and operation of FGD systems with attendant lower overall costs. Electric utilities have developed computer models to predict FGD system operations (i.e., the FGD-PRISM model of the Electric Power Research Institute). These models require geologic data such as reactivity that are commonly unavailable. We generated data needed for the model during a cooperative effort among the Indiana Department of Commerce, the Indiana Geological Survey (IGS), The Indianapolis Power & Light Company (IP&L), and the Indiana Mineral Aggregates Association. Our goal was to provide missing geologic details of Indiana scrubber-stone raw materials and apply them to the FGD-PRISM model to provide general guidance to determine which geologic units can provide stone for most efficient sulfur removal. Results of the model for selected limestones and parameters specific to one IP&L generating plant were calculated. Geologic data generated may be applied to other generating operations, and our examples should help other utilities optimize their FGD strategies. Several hundred samples from more than 30 active quarries were collected and their physical properties determined. Grindability values ranged from 7.2 to 21.7 for 50 selected samples. Acid-insoluble residues of less than 1% to 13% were found. Dissolution rates as an index of reactivity varied over two orders of magnitude for the selected set of samples. These data plus chemical analyses and Ca/Mg ratios were entered into a generic scrubber model to determine rates of stone use and scrubber efficiency for various stone. Removal of SO2 was projected by this model to range from 89% to 98% with stone utilization rates from 91% to 93%. Excellent scrubber stone sources were found in Mississippian rocks in central and southern Indiana. Rocks of the Ste. Genevieve and Salem Limestones were especially efficient. Even small amounts of dolomite, clay minerals, and quartz diminished a stone's usefulness for FGD scrubbing.

Jan 1, 1999

By Sandy Worden

Coal mining companies in Australia are managing the high-consequence risks across their operations more effectively by using an interactive online risk management system known as Riskgate Developed by the Minerals Industry Safety and Health Centre (MISHC) at the University of Queensland, Australia, Riskgate contains detailed information about 11 high-consequence risk areas (called topics in the system) for opencut and underground coal mines (Table 1). The existing topics are: fires; strata control for underground mining; ground control for opencut mining; tires; isolation; collisions; explosions and explosives; manual tasks; and trips, slips and falls. Every Riskgate topic is focused on coal industry activities (mining, processing, transport and storage). The scope includes mine sites, lease areas and mine infrastructure (mobile, fixed plant, field equipment, buildings, road and rail transport), and all aspects of the mine life cycle from design through to decommissioning. The topics uniformly recognize that a loss of control can result in injury or fatality, equipment damage, production loss, reputation loss and environmental damage. However, the priority focus for Riskgate is the safety of mine personnel.

Jul 1, 2013

By A. B. Cecala

Two recent Bureau studies evaluated workers' dust exposures in automated pallet loading processes. The first study involved a Bureau designed dust control system using a push-pull ventilation technique. The unit was shown to reduce workers' dust exposures by 76% during pallet loading at a ground silica operation. A hydraulic lift table was used to automate the bag stacking process; this kept the loading height constant throughout the entire pallet loading cycle. The second study evaluated different commercial automated pallet loading systems. These systems automatically stack the bags onto pallets, shrink wrap the pallets, and deliver the pallets to a fork lift pickup location. Results from a ground silica evaluation site indicated respirable dust samples taken were below the Threshold Limit Value (TLV) as established by the Mine Safety and Health Administration (MSHA).

Jan 1, 1990

By A. Aly Selirn

An economic simulation model was developed to predict the amount of copper recovered from copper oxide deposits and the cost of producing it as a function of the deposit parameters. The economic simulation model includes models of fragmentation design and cost, copper extraction, solution distribution and recovery, effluent solution cutoff grade, and financial analysis. Cost and price indices were also developed to evaluate the economic feasibility of in situ leaching operations as a function of their starting date. Application of the models to various properties having the same area and different ore thickness shows that the effluent solution cutoff grade does not vary with the ore thickness nor with its grade. The percent of copper recovery is, however, shown to increase with the increase in the ore thickness and is independent of the ore grade. it is also shown that while the profit per unit of extracted copper increases with the increase in ore grade or ore thickness, the rate of return on total investment does not show any correlation

Jan 1, 1977

By Christopher Mark

Horizontal stresses are caused by global plate tectonic forces. During 1995 alone, they were largely responsible for closing two U.S. longwall mines. This paper presents six case histories from Pennsylvania, West Virginia, Kentucky, and Alabama. In each case history, a mine encountered roof falls or difficult ground conditions in the headgate, caused by horizontal stress concentrations. The problems are detailed, and the control measures adopted are described. In most cases, nearby longwall panels without stress concentrations were trouble-free. The paper also discusses detailed measurements made at two adjacent Pennsylvania longwalls. One headgate was oriented to avoid a horizontal stress concentration, and the other was not. Eliminating the stress concentration dramatically reduced roof support loads and roof deformation. The paper concludes that proper panel orientation and sequence is the key to maintaining headgate ground control. The optimum orientation is not parallel with the maximum horizontal stress, as previously thought, but rather 20° in the stress shadow of the gob. Other stress control techniques, including artificial support, are briefly discussed.

Jan 1, 1997

By A. Wallace Mitchell

Barite deposits in Nevada occur as bedded and vein-types along a north-northeastern -trending zone which parallels the Antler orogenic belt The bedded deposits of Nevada are the most significant economically. They are presently supplying eighty-five percent of the domestic barite production which is used primarily as a weighting agent in the petroleum drilling industry. The ore bodies are controlled both structurally and stratigraphically, occurring along regional and local structural breaks in siliceous eugeosynclinal rocks of mid-Paleozoic age. Evidence for origin of the barite includes sedimentary and hydrothermal features indicating that localization probably took place along fractures in the seafloor.

Jan 1, 1980

By T. E. Masoner

The struggle to get the minerals industry seriously interested in high intensity wet magnetic separation* has been difficult. The high capital cost of the equipment, the lack of basic research, the lack of operating information, and the diverse characteristics associated with different minerals and ores have prevented the development and use of HIMS-W on a wide scale. The Climax Molybdenum Company, a Division of American Metal Climax, Inc., located at Climax, Colorado, was among the first companies in the Americas in recent years to support the development of HIMS-W to recover weakly magnetic minerals on a large scale. The Climax Molybdenum Company, one of the world's largest underground mines, processes about 40,000 tons per day of ore, from which about fifty million pounds of molybdenum disulfide are produced each year. By-products include tungsten, iron pyrite, tin, and some monazite.

Jan 1, 1968

By Jr. Pickering

Commercial quality kaolin deposits occur in fluvial sediments in both central-eastern Georgia and in the eastern Amazon River area of Brazil. Distinctive coarse and fine particle size kaolin deposits are present in both areas; they have many remarkable similarities for mineral deposits occurring at such wide geographic separation. Industrial, mineralogical, crystalline, and chemical resemblance of the coarse and fine kaolin deposits from the two areas will be described in detail. Knowledge of similarities of the Brazilian clays to those which have dominated world production in Georgia will help to develop superior quality kaolin products for world use in paper, paint, plastic, ceramic, and other applications.

Jan 1, 1997

By H. V. Scotland III

Lafarge Corporation's Texas Quarry, in Baltimore MD, achieved a substantial expansion of pit reserves by removing an inactive underground mine. The day lighting program, designed, and completed in 1997, open pit mined more than 400 meters of room and pillar workings which were originally developed to recover high brightness Calcium Carbonate. The project proved to be a challenge throughout its course as the pit plan was modified and successful daylighting techniques were developed to remove the mine without adversely affecting the safety of the operation, quality of the stone recovered, or negatively impacting the surrounding community. The design parameters and techniques developed and implemented at Texas may prove of interest to other operators as they are faced with daylighting opportunities. This article will detail the challenges we faced and the solutions which made the project a success.

Jan 1, 1999

By C. D. Litton, I. E. Perera

Experiments were conducted to evaluate the response characteristics of commercially available gas, smoke and flame sensors to fires of common combustible mine materials. The experiments were conducted in the large-scale fire gallery located at the National Institute for Occupational Safety and Health (NIOSH) Lake Lynn Laboratory in Fairchance, PA, using ponderosa pine, red oak, Douglas fir, high and low volatile coals, polyvinyl chloride (PVC) and styrene butadiene rubber (SBR) conveyor belts, No. 2 diesel fuel and diesel exhaust. All the experiments (except those using No. 2 diesel fuel and the diesel exhaust tests) were conducted in a similar manner, with combustible materials heated rapidly by electrical strip heaters, producing smoldering fires that quickly transitioned into flaming fires. The sensors included a diffusion-type carbon monoxide (CO) sensor, photoelectric- and ionization-type smoke sensors, a video smoke/flame detector and an optical flame detector. Simultaneous measurements were obtained for average gas concentrations, smoke mass concentrations and smoke optical densities in order to quantify the levels of combustion products at the alert and alarm times of the sensors. Because the required sensor alarm levels are 10 ppm and 0.044 m-1 optical density for CO and smoke sensors, respectively, the different sensor alarms are compared to the time at which the CO and smoke reached these alarm levels (Litton et al., 1991). In addition, the potential impact of using smoke sensors that have met the performance standards from accredited testing laboratories is also evaluated using the response of an Underwriters’ Laboratory (UL)-approved combination photoelectric/ionization smoke detector. The results are discussed relative to fire sensor needs that can have a positive impact on mine fire safety.

Jan 1, 2014

By P. Soupios

Seismic geophysical methods have long been used by geologists and geophysicists to delineate subsurface features. These techniques work because different types and strengths of soil and rock transmit energy at different velocities. The Crosshole-Downhole tests (CH-DH) and seismic refraction survey (RS) are among the most used methods in engineering applications to obtain the elastic properties of subsurface layers. As a result, seismic methods have evolved into a cost-effective tool for rapidly determining depth to bedrock in engineering and construction projects. The seismic methods are best suited to sediment thickness analysis, bedrock quality determination and detection of the presence of weaknesses in the bedrock before the erection of any civil engineering structures such as bridges, tunnels, dams and portals. Seismic methods are also useful in estimating the rippability of bedrock ahead of construction. These methods are particularly useful for large-scale projects that require a significant number of drill holes, resulting in a substantial investment of time and costs for drilling. The CH-DH and RS methods are typically comparable in total cost to drilling, but provide significantly more information in 2-D and 3-D and therefore reduce the likelihood of conceptually oversimplifying the subsurface conditions. The above mentioned methodologies were considered to be the most appropriate geophysical methods for investigating the shallow structure and the dynamic soil properties of the area where the Ilarionas Dam is scheduled to be constructed. The main target of this work was to prove the potential of geophysical methods in providing accurate information to the civil engineer and to obtain information on the dynamic soil and rock properties for earthquake design analyses for the dam construction. Specifically, nine refraction seismic profiles and three cross-hole-downhole seismic tests were implemented to determine the subsurface conditions of the study area. The tests determined the shear and compression wave velocity profiles versus depth and other crucial parameters such as Young and Rigidity modules. Furthermore, they allowed the detailed 2-D mapping (along several profiles of the study area) of the subsurface variation of the soil and rock dynamic moduli.

Jan 1, 2006

By Jon Ike Isaacson, Michael Miller, Jarek Trela

Despite reef structures being relatively common in carbonate rocks around the world, tunneling experience in reefs is extremely rare. Impacts and risks associated with reef tunneling through these geologic features were also relatively unknown. A new reef was encountered during construction of the Lower Pogues Run Tunnel in Indianapolis, exposed over 5,000 linear feet along the alignment, resulting in adverse impacts on construction. Analysis of investigation data and construction from this encounter provide insight into the identification and characterization of reefs along tunnel alignments as well as the potential impacts on construction for future tunneling within reef structures.

Jun 23, 2024

By A. Juganda, Jr. Bogin, J. Brune, J. Grubb, S. Lolon

"Face ignitions at the longwall face are a serious hazard in underground coal operation that can lead to a major mine explosion. Despite having methane monitoring system mounted on the shearer and at various locations on the longwall face, undetected accumulations of methane can still occur and result in face ignitions. With the use of Computational Fluid Dynamics (CFD), the interaction between the air flow at the longwall face and factors that contribute to the accumulation of methane around the longwall face can be modeled and visualized in great detail. The results confirm that the tailgate corner of longwall face is a critical area that is prone to face ignitions and needs to be properly monitored. The occurrence of roof falls on the tailgate entry inby the face and/or poor caving conditions behind the shields can pose a safety risk in the longwall operation. Poor gob caving can lead to insufficient face air quantity to dilute methane at the tailgate corner, while blocking of tailgate by a roof fall can carry methane contaminated air from behind the shields back into the face near the tailgate corner and pull the explosive gas zones (EGZs) inside the gob closer to the face. INTRODUCTION Ignitions of accumulated methane gas at longwall faces are well known to be among the major causes of methane explosion in underground coal longwall mining operations. Some of these ignitions can lead to major mine explosions, such as the Upper Big Branch mine disaster in 2010, in which methane migrated from the gob to the shearer cutting drum where it was ignited, resulting in a major mine disaster (Phillips, 2012). History has shown that, despite having methane monitoring systems mounted on the shearer and various locations at the longwall face and alarms set to 1% CH4 (Mine Safety & Health Administration, 2012), undetected accumulations of explosive methane-air-mixtures can still occur and result in face ignitions. Recent study by Verma and Brune (2016) state that frictional ignitions on longwall faces contributed to 379 incidents or 23% of the total 1,637 cases of face ignitions recorded from 1983 to 2014. The common cause of mine explosions usually involves poorly designed ventilation systems, insufficient ventilation, and inadequate monitoring in critical areas that are prone to methane accumulations. In longwall operation, the tailgate corner of the longwall face can be considered as one such critical area. On-site studies by Krog et al (2006) and Thakur (2008) show that increasing the longwall panel width may also increase cumulative methane emissions at the tailgate. There are also indications that increasing longwall face lengths can result in an increase of the void space behind the face under certain roof conditions (Schatzel et al, 2006). This may cause higher leakage rates from the face to the gob, thus reducing the amount of fresh air available at the tailgate."

Jan 1, 2017

A linear programming model with integer sequencing variables is developed to schedule limestone production for a quarry in Central Japan. The model is used to optimize raw material production from the quarry supplying limestone to cement, quick lime and aggregate plants. Typically, the mining in the quarry takes place in four to six different areas each area having 3 or 4 mining increments. Each mining increment contains different quality of limestone. The limestone production from the quarry is transported to the plants byway of 3 ore passes. Each plant requires a given quantity of limestone per period meeting certain quality constraints. This paper will describe development of the scheduling optimization model and how it is used to schedule production by period within the quarry to meet the capacity and blending requirements of the plants.

Jan 1, 2003